AL8-V855Stereo Bluetooth Headset

BLUETOOTH ® HEADSET Guía del usuario  Plantronics Voyager 855 EN ENGLISH TABLE OF CONTENTS Welcome 3 What is Bluetooth? 3 Package Contents & Features 4 Charging 5 Pairing 6 Custom Fit 8 Headset Controls 12 Stereo Headset Controls 13 Indicators 15 Range 15 Hands-Free Features 16 Optional Accessories 17 Troubleshooting 18 Product Specifications 19 Technical Assistance 1 9 Limited Warranty 19 Important Safety and Operational Information 20 Regulatory Notices 22 Plantronics Voyager 855 EN ENGLISH WELCOmE Thank you for choosing the Plantronics Voyager™ 855 headset. To get the most from your new headset, we recommend that you take the following steps: Read this User Guide, including all the safety information at the end of this guide, before you use your headset. If you need assistance, please do the following: Follow the steps in the “Troubleshooting” section on page 18. Contact the Plantronics Technical Assistance Center at 866-363-BLUE (2583) or visit www.plantronics.com/support. Visit www.plantronics.com/productregistration to register your headset online, so we can provide you with the best possible service and technical support. NOTE: If you are considering returning the product, please contact the Technical Assistance Center first. 1. . • • . WhAT iS Bluetooth? Bluetooth wireless technology provides a way for devices to communicate with each other using short-range radio frequency instead of wires. Any two Bluetooth devices can communicate as long as they both have Bluetooth turned on, they are within range, and they have been paired – a quick “handshake” that connects the two devices. Bluetooth range is up to 33 feet (10 meters). Obstructions, such as walls or other electronic devices, can cause interference or shorten the effective range. For optimal performance, place your headset and phone on the same side of your body.  Plantronics Voyager 855 EN ENGLISH PACkAgE CONTENTS & FEATurES Call control button (on/off) Mute microphone (Pause/Play*) Volume up/down (Track forward/back*) Extendable boom Microphone port Ear loop stabilizer Stereo plug-in cable Sound isolating ear bud (small, medium and large) AC Charger 100 – 240V * Stereo mode only and requires Bluetooth AVRCP (Audio Video Remote Control Profile). See “Stereo Headset Controls” on page 13 for details. 1. . . . 5. 6. 7. 8. 9. 1  5 6 9 7  8 5Plantronics Voyager 855 EN ENGLISH ChArgiNg Before you use your headset for the first time, charge it for at least 1 hour. It takes approximately 3 hours to fully charge your headset. Connect the charger cable to the headset. Plug the charger into a power outlet. While your headset is charging the indicator glows red. When your headset is fully charged, the indicator turns off. WARNING: Do not use your headset while it is connected to the charger. CHECk THE CHARGE LEvEL When your headset is on, simultaneously press and hold the call control button and the volume down button for about two seconds. The indicator flashes red to show the charge level. 1. . Red FlashesBattery Level 1More than 2/3 full 21/3 to 2/3 full 3Less than 1/3 full 6 Plantronics Voyager 855 EN ENGLISH PAiriNg Pairing is the process of introducing your headset to your phone. Before using your headset for the first time, you must pair it with your Bluetooth phone. Normally you need to pair your headset with your phone only once. To see a demo of the pairing process, visit www.plantronics.com/easytopair. QuIC kPAIR™ TECHNOLOGy Your new headset includes Plantronics QuickPair technology to simplify the Bluetooth setup process. The first time you turn your headset on, your headset automatically enters pairing mode for 10 minutes. Once paired successfully, your headset stays on for instant use. If not successfully paired after 10 minutes, your headset automatically powers off. When you turn the headset on again, it automatically goes into pairing mode until successfully paired with a Bluetooth phone. To pair your headset for the first time: Turn ON the Bluetooth feature on your phone. TIP: For most phones, select Settings/Tools > Connections > Bluetooth > On. See your phone’s user guide for more information. Press and hold the call control button to turn on your headset. (The indicator flashes red/blue to show that the headset is on and in pairing mode.) TIP: If you don’t see the red/blue flash, press and hold the call control button to turn your headset off, and then press and hold the call control button again until you see the red/blue flash. Use the commands on your phone to locate your headset. TIP: For most phones, select Settings/Tools > Connections > Bluetooth > Search > 8XXPlantronics. See your phone’s user guide for more information. When prompted for the passkey, enter 0000. When pairing is successful, the red/blue indicator on your headset turns off. Your headset is now connected and ready to use. 1. . . .    1 7Plantronics Voyager 855 EN ENGLISH SubSEQuENT P AIRING If you’ve already paired your headset with another device, follow these steps: Turn ON the Bluetooth feature on your phone. TIP: For most phones, select Settings/Tools > Connections > Bluetooth > On. See your phone’s user guide for more information. Turn the headset off by pressing and holding the call control button until the indicator turns red and then turns off. Turn the headset back on by pressing and holding the call control button until the indicator flashes red/blue. The headset remains in pairing mode for 3 minutes. Use the commands on your phone to locate your headset. TIP: For most phones, select Settings/Tools > Connections > Bluetooth > Search > 8XXPlantronics. See your phone’s user guide for more information. When prompted for the passkey, enter 0000. When pairing is successful, the indicator on your headset turns off. Your headset is now connected and ready to use. 1. . . . 5. 8 Plantronics Voyager 855 EN ENGLISH CuSTOm FiT The Plantronics Voyager 855 headset comes with three sizes of sound isolating ear buds. We recommend…

Text truncated - open the document above for the full version.

DATE: June 26, 2007 Federal Communications Commission Equipment Authorization branch 7435 Oakland Mills Road Columbia, MD 21046 Re: Request for Confidentiality Gentlemen: In reference to the application under FCC ID: AL8-V855 and pursuant to Sections 0.457(d)(l)(ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of the accompanying information as outlined below: Schematics Block Diagrams Theory of Operation These documents contain detailed system and equipment description and related information about the product that Plantronics considers to be proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, Plantronics considers that this information would be of benefit to its competitors, and that disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, Alvin Ilarina Compliance Engineer Worldwide Headquarters 345 Encinal Street z P.O. Box 635 Santa Cruz, CA 95060

Worldwide Headquarters 345 Encinal Street z P.O. Box 635 Santa Cruz, CA 95060 Bluetooth Declaration Per FCC 15.247 Requirements 1 Output power and channel separation of a Bluetooth device in the different operating modes: The different operating modes (data-mode, acquisition-mode) of a Bluetooth device don’t influence the output power and the channel spacing. There is only one transmitter which is driven by identical input parameters concerning these two parameters. Only a different hopping sequence will be used. For this reason the check of these RF parameters in one op-mode is sufficient. 2 Frequency range of a Bluetooth device: Hereby we declare that the maximum frequency of this device is: 2402 – 2480 MHz. This is according the Bluetooth Core Specification V 2.0 + EDR for devices which will be operated in the USA. This was checked during the Bluetooth Qualification tests (Test Case: TRM/CA/04-E). Other frequency ranges ( e.g. for Spain, France, Japan) which are allowed according the Core Specification are not supported by this device. 3 Co-ordination of the hopping sequence in data mode to avoid simultaneous occupancy by multiple transmitters: Bluetooth units which want to communicate with other units must be organized in a structure called piconet. This piconet consist of max. 8 Bluetooth units. One unit is the master the other seven are the slaves. The master co-ordinates frequency occupation in this piconet for all units. As the master hop sequence is derived from it’s BD address which is unique for every Bluetooth device, additional masters intending to establish new piconets will always use different hop sequences. 4 Example of a hopping sequence in data mode: Example of a 79 hopping sequence in data mode: 40, 21, 44, 23, 42, 53, 46, 55, 48, 33, 52, 35, 50, 65, 54, 67, 56, 37, 60, 39, 58, 69, 62, 71, 64, 25, 68, 27, 66, 57, 70, 59, 72, 29, 76, 31, 74, 61, 78, 63, 01, 41, 05, 43, 03, 73, 07, 75, 09, 45, 13, 47, 11, 77, 15, 00, 64, 49, 66, 53, 68, 02, 70, 06, 01, 51, 03, 55, 05, 04 5 Equally average use of frequencies in data mode and behaviour for short transmissions: The generation of the hopping sequence in connection mode depends essentially on two input values: 1. LAP/UAP of the master of the connection 2. Internal master clock The LAP (lower address part) are the 24 LSB’s of the 48 BD_ADDRESS. The BD_ADDRESS is an unambiguous number of every Bluetooth unit. The UAP (upper address part) are the 24 MSB’s of the 48 BD_ADDRESS. Worldwide Headquarters 345 Encinal Street z P.O. Box 635 Santa Cruz, CA 95060 The internal clock of a Bluetooth unit is derived from a free running clock which is never adjusted and is never turned off. For synchronisation with other units only offset are used. It has no relation to the time of the day. Its resolution is at least half the RX/TX slot length of 312.5 μs. The clock has a cycle of about one day (23h30). In most case it is implemented as 28 bit counter. For the deriving of the hopping sequence the entire LAP (24 bits), 4 LSB’s (4 bits) (Input 1) and the 27 MSB’s of the clock (Input 2) are used. With this input values different mathematical procedures (permutations, additions, XOR- operations) are performed to generate the sequence. This will be done at the beginning of every new transmission. Regarding short transmissions the Bluetooth system has the following behaviors: The first connection between the two devices is established, a hopping sequence was generated. For transmitting the wanted data the complete hopping sequence was not used. The connection ended. The second connection will be established. A new hopping sequence is generated. Due to the fact that the Bluetooth clock has a different value, because the period between the two transmission is longer (and it cannot be shorter) than the minimum resolution of the clock (312.5 μs). The hopping sequence will always differ from the first one. 6 Receiver input bandwidth and behaviors for repeated single or multiple packets: The input bandwidth of the receiver is 1 MHz. In every connection one Bluetooth device is the master and the other one is the slave. The master determines the hopping sequence (see chapter 5). The slave follows this sequence. Both devices shift between RX and TX time slot according to the clock of the master. Additionally the type of connection (e.g. single or multislot packet) is set up at the beginning of the connection. The master adapts its hopping frequency and its TX/RX timing according to the packet type of the connection. Also the slave of the connection will use these settings. Repeating of a packet has no influence on the hopping sequence. The hopping sequence generated by the master of the connection will be followed in any case. That means, a repeated packet will not be send on the same frequency, it is send on the next frequency of the hopping sequence. 7 Dwell time in data mode The dwell time of 0.3797s within a 30 second period in data mode is independent from the packet type (packet length). The calculation for a 30 second period is a follows: Dwell time = time slot length * hop rate / number of hopping channels *30s Example for a DH1 packet (with a maximum length of one time slot) Dwell time = 625 μs * 1600 1/s / 79 * 30s = 0.3797s (in a 30s period) For multislot packet the hopping is reduced according to the length of the packet. Example for a DH5 packet (with a maximum length of five time slots) Dwell time = 5 * 625 μs * 1600 * 1/5 *1/s / 79 * 30s = 0.3797s (in a 30s period) This is according the Bluetooth Core Specification V 1.0B (+ critical errata) for all Worldwide Headquarters 345 Encinal Street z P.O. Box 635 Santa Cruz, CA 95060 Bluetooth devices. There for all Bluetooth devices comply with the FCC dwell time requirement in data mode. This was checked during the Bluetooth Qualification tests. The Dwell time in hybrid mode is measured and stated in the test report. 8 Channel Separation in hybrid mode The nominal channel spacing of the Bluetooth s…

Text truncated - open the document above for the full version.

Voyager 855 External Photos Top With Earloop Bottom With Earloop Voyager 855 External Photos (continued) Left Right

ARTMASTER REV. LEVEL: REF. PART #: DESCRIPTION: PREPARED BY:DATE: PMS COLOR #: 74956-01 (Body, Painted, Gemini) Gemini (Stereo) headset laser etching: Regulatory artwork 76226-00 N/A 26 J. Yang April 2, 2007 NOT FOR RESALE AB 1.1 Voyager 855 NOT FOR RESALE AB 1.1 Voyager 855 NOT FOR RESALE AB 1.1 Voyager 855 FCC ID: AL8-V855 IC:457A-V855 SW MYY 1:1 reference (Sliding Boom) Scale: 2:1 Scale: 1:1 1:1 reference (Bottom Housing) Scale: 2:1 Scale: 1:1 FCC ID: AL8-V855 IC:457A-V855 SW MYY FCC ID: AL8-V855 IC:457A-V855 SW MYY 22 mm 4 mm 14 mm 13 mm 12.5 mm 5.5 mm

Voyager 855 Internal Photos Assembly Components PCB Top Voyager 855 Internal Photos (continued) PCB Top – No Shield PCB Bottom with battery Voyager 855 Internal Photos (continued) PCB Bottom no battery

2400MHz 2450MHz 2500MHz Efficienc y [dB] -1.7 -1.5 -1.5 ( 67%) ( 71%) ( 71%) Peak gain [dBi] 1.3 1.8 1.1 Average XY-plane TX-H -2.9 -2.6 -2.9 gain TX-V -20.1 -18.7 -18.1 [dBi] YZ-plane TX-H -2.8 -2.7 -2.9 TX-V -16.3 -16.1 -16.6 ZX-plane TX-H -17.2 -17.3 -17.5 TX-V 0.0 0.2 0.1 XY-plane YZ-plane ZX-plane @2450MHz (-X) (+Z) (+Z) (-Y) (+Y) (-Y) (+Y) (+X) (-X) unit: dBi (+X) (-Z) (-Z) -45-35-25-15 -5 5 TX-HTX-V +Y +X +Z +Y +X +Z +Y +X +Z -45-35-25-15 -5 5 TX-HTX-V -45-35-25-15 -5 5 TX-HTX-V Bandwise: 150MHz (VSWR<2) Efficiency > -1.7dB (71%) Peak Gain > +1.1dBiAverage Gain > +0.0dBi (ZX plane-Vertical polarization) 䂓 Radiation Pattern 䂓 Electrical Characteristics VSWR Element-GND Distance: 1mm 8 x 3 x 1 mm 䂓 Shapes *on Taiyo Yuden’s Evaluation Board*GND size on evaluation board: 45x15mm 2.4GHz Multilayer Antenna 2.4GHz Multilayer Antenna : AH 083F245001 : AH 083F245001 Small / Stable Performance /Inverted-F Confidential Confidential -1- 㧙2㧙 1.0 Scope This specification covers the multilayer chip antenna in mounted condition on Taiyo Yuden evaluation board. Part Numbering System  AH 083F245001㧙 T       2.0 Environmental condition Refer to the reliability test of table -1 for the reliability assurance. 2.1 Operating temperature range 㧦 -20͠ to +80͠ 2.2 Humidity  㧦 15㨪95%RH (Withoutdew condensation)   2.3 Storage temperature range 㧔Antenna of single unit㧕 㧦 -40͠ to +85͠ 2.4 Storage temperature and humidity range (packaging condition) 㧦 -10͠ to +40͠, 15 to 85% RH 3.0 Electrical specifications 3.1 Input Impedance  㧦 50ǡ(Specified value ) 3.2 Frequency bandwidth 㧦 2400 to 2500MHz 3.3 Gain 㧖 1  㧦 +2 dBi min. (Peak) 㧦 -1 dBi min. (Vertical polarization average gain of omni directional plane) 㧦 -6 dBi min. (Total average gain) 3.4 VSWR in bandwidth 㧖 2 㧦 3.0 (Typical) 㧖1: Total average gain in 3.3 of electrical characteristics shall be total average gain of V, H polarization in X-Y, Y-Z and X-Z side (Average of total measurement points) in mounted on Taiyo Yuden evaluation board. 㧖2: VSWR in bandwidth in 3.4 of electrical specification shall be VSWR mounted on Taiyo Yuden on standard board. 4.0 Mechanical specifications 4.1 Shape dimension, indication mark: Refer to figure -1. Sealed letter shall be E26. 4.2 Dimension of evaluation board and land-patterns: Refer to figure -2, 3.  Package (T: Taping) Individual specification Frequency bandwidth (4-digit number in MHz) Size (mm) Antenna Class Type 㧙3㧙 Reflow soldering temperature profile Recommended reflow profile        #DQWVU㨪U㨪U  Te m p ͠ ͠ Peak temperature: 250㨪255͠ Time㧔sec㧕 㧙4㧙 Figure -1 Part number: PG_AH_083F245001-T Shape dimension Unit: mm 㧙5㧙 Pin arrangement ̪ Top side view Indication and marker 䋱 FEED 䋵䌎䌃 䋲䌇䌎䌄 䋳䌎䌃 䋴䌎䌃 㶎Top side view Direction marking: 0.48mmǾ 1 32 5 4 Feed marking: Input terminal is prescribed 0.5mmغ An intestinal pattern code: 1.6mm height 3-digit alpha numeric 㧙6㧙 Figure -2 Dimension of evaluation board for this antenna Unit: mm  ࡮Board material: FR-4 ࡮Thickness of base material: 0.8mm ࡮Electrode pattern: single-side ࡮Thickness of electrode: 35Ǵm ࡮Land part: Refer to figure3 Electrode pattern Board size 15 50 45 5.5 15 Ground pattern 㧙7㧙 Figure -3 Antenna land-patterns Land for input terminal Land for GND terminal Land for NC terminal ̪1 : A solder area is set at solder resist ̪2 : Please don't arrange the surface and inside layer pattern near the antenna mounting area. (Refer to our company evaluation circuit board.) ̪1 50ǡ input GND 0.5 1 ̪2 1 3.3 0.9 1 5.2 1 Unit: mm 1 2 Resist 㧙8㧙 Precautions 1. Be careful of using these products because characteristics may be deteriorated if it is used in the following environment. ࡮Special gas atmosphere (Such as CI2, NH3, SOx and Nox, etc.) ࡮Gas atmosphere with volatility and flammability ࡮Place where dust is abundant ࡮Place where water splashes directly, dew condensation is ease to occur because of high humidity,  direct sunlight is subjected and freeze. 2. Be careful not to apply excessive pressure and shock because these products are made from ceramics element. 3. Be careful not to apply excessive pressure and shock to these products during transporting and handling of print circuit board that these products are soldered. 4. Be careful of handling (Don’t drop and hit) because characteristics changes when electrode is damaged and chipped out. And be careful not to touch these products with bare hands because it causes a solderability decline. 5. Please storage under the following condition. Temperature: -10͠ to +40͠ Humidity: 15% to 85% RH Please use these products after the delivery within six months. And after more than six months have passed, please confirm solderability before the use of them. 6. Please arrange these products of position of mounting where stress isn't applied against bend and deflection of circuit board. Be careful not to apply stress and deflection of board during process after soldering these products (circuit board cut, break board checker, mounting of other components, installation to chassis and wave soldering to backside of the circuit board after reflow soldering) because electrode peeling and chip break may occur when circuit board bends during handling. When separating print circuit board after mounting, please avoid hand breaking and use special tools. 7. Be careful not to apply excessive stress and shock to prevent break and chip out during mounting these products on print circuit board. 8. Please use flux containing less than 0.1% wt (cl conversion) of halogen material in soldering to prevent corrosion of electrodes and decline of insulation resistance. 9. Please preheat in soldering so as to be less than 100͠ between solder temperature and products temperate to prevent break of these products. 10. When ultrasonic washing is applied, please confirm cl…

Text truncated - open the document above for the full version.

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR STEREO BLUETOOTH HEADSET MODEL NUMBER: VOYAGER 855 FCC ID: AL8-V855 REPORT NUMBER: 07U11114-1 ISSUE DATE: JUNE 25, 2007 Prepared for PLANTRONICS, INC. 345 ENCINAL STREET SANTA CRUZ, CA 95060, U.S.A. Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 2 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- 06/25/07 Initial Issue T. Chan REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 3 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS............................................................................................. 4 2. TEST METHODOLOGY .................................................................................................................. 5 3. FACILITIES AND ACCREDITATION .......................................................................................... 5 4. CALIBRATION AND UNCERTAINTY.......................................................................................... 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 5 4.2. MEASUREMENT UNCERTAINTY ............................................................................................... 5 5. EQUIPMENT UNDER TEST............................................................................................................6 5.1. DESCRIPTION OF EUT ..............................................................................................................6 5.2. MAXIMUM OUTPUT POWER .................................................................................................... 6 5.3. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................................. 6 5.4. SOFTWARE AND FIRMWARE .................................................................................................... 6 5.5. WORST-CASE CONFIGURATION AND MODE......................................................................... 7 5.6. DESCRIPTION OF TEST SETUP ................................................................................................ 7 6. TEST AND MEASUREMENT EQUIPMENT ................................................................................ 9 7. LIMITS AND RESULTS ................................................................................................................. 10 7.1. ANTENNA PORT CHANNEL TESTS ......................................................................................... 10 7.1.1. 20 dB BANDWIDTH ......................................................................................................... 10 7.1.2. HOPPING FREQUENCY SEPARATION......................................................................... 14 7.1.3. NUMBER OF HOPPING CHANNELS ............................................................................. 16 7.1.4. AVERAGE TIME OF OCCUPANCY ............................................................................... 21 7.1.5. PEAK OUTPUT POWER .................................................................................................. 24 7.1.6. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................ 28 7.1.7. AVERAGE POWER........................................................................................................... 31 7.1.8. CONDUCTED SPURIOUS EMISSIONS.......................................................................... 32 7.2. RADIATED EMISSIONS.............................................................................................................41 7.2.1. TRANSMITTER RADIATED SPURIOUS EMISSIONS ................................................. 41 7.2.2. TRANSMITTER RADIATED EMISSIONS ABOVE 1 GHZ .......................................... 44 7.2.3. WORST-CASE RADIATED EMISSIONS BELOW 1 GHz ............................................. 53 7.3. POWERLINE CONDUCTED EMISSIONS ................................................................................ 57 8. SETUP PHOTOS .............................................................................................................................. 61 REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 4 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: PLANTRONICS, INC. 345 ENCINAL STREET SANTA CRUZ, CA 95060, U.S.A. EUT DESCRIPTION: STEREO BLUETOOTH HEADSET MODEL: VOYAGER 855 SERIAL NUMBER: CS01978 DATE TESTED: JUNE 7-15, 2007 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 15 SUBPART C NO NON-COMPLIANCE NOTED Compliance Certification Services, Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by Compliance Certifi…

Text truncated - open the document above for the full version.

REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 61 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 8. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 62 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED RF MEASUREMENT SETUP RADIATED X ORIENTATION RADIATED Y ORIENTATION REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 63 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 64 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED Z ORIENTATION REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 65 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED FRONT PHOTO REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 66 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED BACK PHOTO REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 67 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP LINE CONDUCTED FRONT PHOTO REPORT NO: 07U11114-1 DATE: JUNE 25, 2007 EUT: STEREO BLUETOOTH HEADSET FCC ID: AL8-V855 Page 68 of 68 COMPLIANCE CERTIFICATION SERVICES DOCUMENT NO: CCSUP4031A 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. END OF REPORT LINE CONDUCTED BACK PHOTO