AL8-VLGDBluetooth headset

Pair Another Phone After pairing your headset to your phone you may want to pair another or new phone. Switch on your headset then tap the Voice button and say "Pair me" to enter pairing mode. Set your phone search and find PLT_Legend to complete the pairing process. Once successfully paired, LEDs stop flashing and you hear “pairing successful.” Phone support plantronics.com/support Online user guide plantronics.com/documentation © 2012 Plantronics, Inc. All Rights Reserved. Bluetooth is a registered trademark of Bluetooth SIG, Inc. and any use by Plantronics is under license. All other trademarks are the property of their respective owners. Patents TEXT pnXXXXX-XX (00.00) amXXXXX-XX Z302 N10687 1 4 4 2 3 2 Voyager Legend GET STARTED CATEGORY Designed in Santa Cruz, California ™ Charge Your Headset Your new headset has enough power to pair and make a few calls. To fully charge it, align both magnetic areas of the headset and USB cable then plug USB end into modular AC charger or laptop for at least 90 minutes. . Reset the Sensors You may need to reset the sensors if a call repeatedly transfers back to your phone even though you are wearing your headset. To reset the sensors, remove headset from your ear, and hold it by the boom for 5 seconds before placing back onto ear. Disable Voice Answer To disable the “answer/ignore” voice command, press and hold the Voice button until you hear a double tone and status confirmation “voice off.” Repeat to reactivate the command. Decipher the LEDs The LEDs flash in response to a change in status or button press. • No LED once fully charged • Flashing red and blue during pairing • Triple red flash when >30 mins talk • Triple blue flash at incoming call Change the Eartip Size To remove the eartip, push it in and twist it to the left to unlock it . Align new eartip into slot, then push in and twist it to the right to lock into place. To wear headset on your other ear, rotate the boom upwards then twist it around tso eartip is on other side before lowering boom. 5 secs for placement only: for placement only: for placement only: Get Paired The first time you put on your headset and slide up the power switch, it begins voice- guided pairing instructions. iPhone: Follow voice-guided instructions and tap the Call button to advance to next step. Android smartphones: Either download our MyHeadset app for one-tap pairing or follow voice-guided instructions from the headset. Other phones: Use your phone’s menus to: 1 Activate Bluetooth on your phone 2 Set to search and find “PLT_Legend” 3 Enter passkey 0000/accept connection. LEDs stop flashing once successfully paired. Take Control Let the Sensors Handle It Smart sensors react when you put on or take off your headset. Putting on your headset will: • Answer an incoming call • Transfer an active call from your phone • Resume streaming audio Taking off your headset will: • Transfer an active call to your phone handset • Pause streaming audio • Lock the call button Use your Voice Tap the Voice button, wait for command request, then say a command, such as: "What can I say?" to hear the full list of available commands "Pair me" to activate pairing mode “Call back” to dial last incoming call "Check battery" for remaining talk time "Am I connected?" to verify connection "Connect me" to re-establish connection "Call Vocalyst" to dial the local Vocalyst number stored in your headset Hear It Whisper Your headset tells you about who is calling you and status changes. For example: “Call from (contact name), answer or ignore?” “Answering call” Talk time (x) hours” “Pairing successful” Your headset understands and speaks in English. You can change the language and other settings online. Connect and update your headset online using your USB cable and our MyHeadsetUp- dater tool at plantronics.com/myheadset. Answer a call Either: • Put on the headset to answer call, or • Say “answer” after call is announced, or • Tap the Call button Reject a call Either: • Say “ignore” after call is announced, or • Press Call button for 2 seconds End a call Tap the Call button to end current call. Voice dial (phone feature) Press the Call button for 2 seconds, wait for phone prompt and then tell the phone to dial the name of a stored contact. Mute the microphone during a call Tap the Mute button . You will hear “mute on” confirmation. An alert repeats every 15 minutes to remind you of microphone mute. Tap the Mute button again to open the microphone and hear “mute off” confirmation. Answer a second call Double-tap the Call button to end the current call and answer second call. Redial or call back last call To redial or call back your last call, either: • Double-tap the Call button or * Press Voice button and say “redial” Adjust the volume Toggle the Volume button up (+) or down (-) during a call or while streaming audio. . voice en For Your Safety fr Pour Votre Sûreté es Para Su Seguridad pt Para Sua Segurança 2 en 3 Important Safety and Operational Information Please read the following safety and operational instructions before using your headset/headphones and accessories. Please keep these instructions for your reference. Additional warnings may be present on the product, packaging, or in the user instructions. This symbol identifies and alerts the user to the presence of important safety warnings. General Operating, storage and charging temperature is 0°C to 40°C (32°F to 104°F). Warnings • Exposure to high volume sound levels or excessive sound pressure may cause temporary or permanent damage to your hearing. Although there is no single volume setting that is appropriate for everyone, you should always use your headset/headphones with the volume set at moderate levels and avoid prolonged exposure to high volume sound levels. The louder the volume, the less time is required before your hearing could be affected. You may experience different sound levels when using your headset /headphones with different devices. The device you use and its se…

Text truncated - open the document above for the full version.

Plantronics, Inc. Date: May 16, 2012 Federal Communications Commission Authorization and Evaluation Division FCC ID: AL8-VLGD ATTESTATION FCC ID: AL8-VLGD Product: Bluetooth headset Model: Voyager Legend We don't provide any controls or software to allow operation outside the USA frequency band when we sell this product in USA. Sincerely, __________________ Peter Clark/Compliance Manager Plantronics, Inc.

Plantronics Inc. Date：May 21, 2012 Federal Communications Commission Authorization and Evaluation Division FCC ID: AL8-VLGD Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: 1 Schematics 2 Block Diagram 3 Operational Description 4 BOM list The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 DFR § 2.803 and the importation rules in 47 CFR § 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices.. We are requesting the commission to grant forty-five days short-term confidentiality request on the following attachments: External Photos Internal Photos Test Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Peter Clark/Compliance Manager Plantronics, Inc.

Plantronics, Inc. Date: 2012-5-17 Federal Communications Commission Authorization and Evaluation Division FCC ID: AL8-VLGD USB function explanation Part 15B testing is not necessary for this device because the USB port is for charge only, no data transmission function. End users are not able to connect to PC for data transmission via USB port. Due to above reasons, this device didn’t perform Part 15B testing, and FCC logo shouldn’t be on the label. Your understanding will be highly appreciated. Sincerely, Peter Clark/Compliance Manager Plantronics, Inc.

1. EUT Photograph (1) EUT Photo (2) EUT Photo Report No： 125S032R-RF-US-P06V01 Page: 2 of 4 (3) EUT Photo (Cable A) (4) EUT Photo (Cable B) Report No： 125S032R-RF-US-P06V01 Page: 3 of 4 (5) EUT Photo (Cable C) (6) EUT Photo (Cable D) Report No： 125S032R-RF-US-P06V01 Page: 4 of 4 (7) EUT Photo (8) EUT Photo

Label location:

(1) EUT Photo (2) EUT Photo (3) EUT Photo (4) EUT Photo

RF Exposure Evaluation Declaration Product Name : Bluetooth Headset Model No. : Voyager Legend FCC ID : AL8-VLGD IC : 457A-VLGD Applicant : Plantronics, Inc. Address : 345 Encinal Street, Santa Cruz, CA95060 USA Date of Receipt : 14/05/2012 Issued Date : 28/05/2012 Report No. : 125S032R-RF-US-P20V01 Report Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF, CNAS or any agency of the Government. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No: 125S032R-RF-US-P20V01 Page: 2 of 5 Test Report Certification Issued Date : 28/05/2012 Report No. : 125S032R-RF-US-P20V01 Product Name : Bluetooth Headset Applicant : Plantronics, Inc. Address : 345 Encinal Street, Santa Cruz, CA95060 USA Manufacturer : Weifang GoerTek Electronics Co., Ltd Address : Dongfang North Road Hi-tech Industry Development District, Weifang Shandong, China Model No. : Voyager Legend FCC ID : AL8-VLGD IC : 457A-VLGD EUT Voltage : DC 3.7V Brand Name : PLANTRONICS Applicable Standard : FCC OET 65 RSS-102: Issue 4, March, 2010 Test Result : Complied Performed Location : Suzhou EMC Laboratory No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Registration Number: 800392; IC Lab Code: 4075B Documented By : (Engineering ADM: Alice Ni) Reviewed By : (Senior Engineer: Jame Yuan) Approved By : (Engineering Manager: Marlin Chen) Report No: 125S032R-RF-US-P20V01 Page: 3 of 5 Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted(audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scope: The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site :http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected] LinKou Testing Laboratory : No.5-22, Ruishukeng, Linkou Dist., New Taipei City 24451, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : [email protected] Suzhou Testing Laboratory : No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., SuZhou, China TEL : +86-512-6251-5088 / FAX : 86-512-6251-5098 E-Mail : [email protected] Taiwan R.O.C. :BSMI, NCC, TAF Germany :TUV Rheinland Norway :Nemko, DNV USA :FCC, NVLAP Japan :VCCI China :CNAS Report No: 125S032R-RF-US-P20V01 Page: 4 of 5 1. RF Exposure Evaluation 1.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r2) Where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Report No: 125S032R-RF-US-P20V01 Page: 5 of 5 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. 1.3. Test Result of RF Exposure Evaluation Product : Bluetooth Headset Test Item : RF Exposure Evaluation Test Site : AC-6 Antenna Gain: Antenna Gain-WLAN: The maximum Gain measured in fully anechoic chamber is 2.59dBi in logarithm scale. Output Power into Antenna & RF Exposure Evaluation Distance: Frequency Band (MHz) Maximum Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm2) 2402 - 2480 MHz 7.2946 0.002635 Note: The power density Pd (4th column) at a distance of 20 cm calculated from the Friis transmission formula is far below the limit of 1 mW/cm2.

Test Report Industry Canada RSS-Gen Issue 3/RSS-210 Issue 8 FCC Part15 Subpart C Product Name : Bluetooth headset Model No. : Voyager Legend FCC ID : AL8-VLGD IC : 457A-VLGD Applicant : Plantronics, Inc. Address : 345 Encinal Street, Santa Cruz, CA95060 USA Date of Receipt : 14/05/2012 Test Date : 15/05/2012~03/06/2012 Issued Date : 04/06/2012 Report No. : 125S032R-RF-US-P06V01 Report Version : V 1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF, CNAS or any agency of the Government. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No： 125S032R-RF-US-P06V01 Page: 2 of 130 Test Report Certification Issued Date : 04/06/2012 Report No. : 125S032R-RF-US-P06V01 Product Name : Bluetooth headset Applicant : Plantronics, Inc. Address : 345 Encinal Street, Santa Cruz, CA95060 USA Manufacturer : Weifang GoerTek Electronics Co., Ltd Address : Dongfang North Road Hi-tech Industry Development District, Weifang Shandong, China Model No. : Voyager Legend FCC ID : AL8-VLGD IC : 457A-VLGD EUT Voltage : DC 3.7V Brand Name : PLANTRONICS Applicable Standard : FCC CFR Title 47 Part 15 Subpart C: 2011 ANSI C63.4: 2009; ANSI C63.10: 2009 Industry Canada RSS-Gen Issue 3/RSS-210 Issue 8 Test Result : Complied Performed Location : Suzhou EMC Laboratory No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., Suzhou, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Registration Number: 800392; IC Lab Code: 4075B Documented By : (Engineering ADM: Alice Ni) Reviewed By : (Senior Engineer: Jame Yuan) Approved By : (Engineering Manager: Marlin Chen) Report No： 125S032R-RF-US-P06V01 Page: 3 of 130 Laboratory Information We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted(audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scope: The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site :http://www.quietek.com/tw/ctg/cts/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory : No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected] LinKou Testing Laboratory : No.5-22, Ruishukeng, Linkou Dist., New Taipei City 24451, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : [email protected] Suzhou Testing Laboratory : No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., SuZhou, China TEL : +86-512-6251-5088 / FAX : 86-512-6251-5098 E-Mail : [email protected] Taiwan R.O.C. :BSMI, NCC, TAF Germany :TUV Rheinland Norway :Nemko, DNV USA :FCC, NVLAP Japan :VCCI China :CNAS Report No： 125S032R-RF-US-P06V01 Page: 4 of 130 TABLE OF CONTENTS Description Page 1. General Information....................................................................................................7 1.1. EUT Description .........................................................................................................7 1.2. Mode of Operation .....................................................................................................9 1.3. Tested System Details..............................................................................................10 1.4. Configuration of Tested System ............................................................................... 11 1.5. EUT Exercise Software ............................................................................................12 2. Technical Test...........................................................................................................13 2.1. Summary of Test Result ...........................................................................................13 2.2. Test Environment.....................................................................................................14 3. Conducted Emission................................................................................................15 3.1. Test Equipment ........................................................................................................15 3.2. Test Setup ................................................................................................................15 3.3. Limit..........................................................................................................................16 3.4. Test Procedure.........................................................................................................16 3.5. Uncertainty ...............................................................................................................16 3.6. Test Result...............................................................................................................17 4. Radiated Emission...................................................................................................33 4.1. Test Equipment ........................................................................................................33 4.2. Test Setup ................................................................................................................34 4.3. Limit..........................................................................................................................35 4.4. Test Procedure..…

Text truncated - open the document above for the full version.

1. Test Setup Photograph Test Mode: Mode 1: Transmit with adapter and cable A Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit with adapter and cable A Description: Back View of Conducted Emission Test Setup Report No： 125S032R-RF-US-P06V01 Page: 2 of 10 Test Mode: Mode 1: Transmit with adapter and cable B Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit with adapter and cable B Description: Back View of Conducted Emission Test Setup Report No： 125S032R-RF-US-P06V01 Page: 3 of 10 Test Mode: Mode 1: Transmit with adapter and cable C Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit with adapter and cable C Description: Back View of Conducted Emission Test Setup Report No： 125S032R-RF-US-P06V01 Page: 4 of 10 Test Mode: Mode 1: Transmit with adapter and cable D Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit with adapter and cable D Description: Back View of Conducted Emission Test Setup Report No： 125S032R-RF-US-P06V01 Page: 5 of 10 Test Mode: Mode 1: Transmit with PC and cable A Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit with PC and cable A Description: Back View of Conducted Emission Test Setup Report No： 125S032R-RF-US-P06V01 Page: 6 of 10 Test Mode: Mode 1: Transmit with PC and cable B Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit with PC and cable B Description: Back View of Conducted Emission Test Setup Report No： 125S032R-RF-US-P06V01 Page: 7 of 10 Test Mode: Mode 1: Transmit with PC and cable C Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit with PC and cable C Description: Back View of Conducted Emission Test Setup Report No： 125S032R-RF-US-P06V01 Page: 8 of 10 Test Mode: Mode 1: Transmit with PC and cable D Description: Front View of Conducted Emission Test Setup Test Mode: Mode 1: Transmit with PC and cable D Description: Back View of Conducted Emission Test Setup Report No： 125S032R-RF-US-P06V01 Page: 9 of 10 Description: Radiated Emission Test Setup for Below 30MHz Description: Radiated Emission Test Setup for Below 1GHz Report No： 125S032R-RF-US-P06V01 Page: 10 of 10 Description: Radiated Emission Test Setup for Above 1GHz Description: Radiated Emission Test Setup for Above 18GHz