APV-2900MBWeatherproof Telematics Gateway Built for Rugged Environments

7/21/2020TTU-2900 Hardware & Installation Guide - PULS Wiki 1/29 TTU-2900 Hardware & Installation Guide TTU-2900™ Hardware and Installation Guide IMPORTANT: DO NOT INSTALL OR USE THE SOFTWARE OR DOCUMENTATION UNTIL YOU HAVE READ AND AGREED TO THE LICENSE AGREEMENT AND REVIEWED THE LIMITED WARRANTY AND REGULATORY INFORMATION. 1Introduction Welcome to the TTU-2900™ Hardware and Installation Guide. This manual is intended to give you information on the basic setup and installation of the CalAmp TTU-2900™ product(s) including hardware descriptions, environmental specifications, wireless network overviews and device installation. 1.1About This Manual The TTU-2900™ is a next generation telematics gateway that includes a range of wireless and peripheral connectivity options and is equipped with CalAmp’s purpose built vehicle interface technologies for both light and heavy-duty vehicle. In order to accurately describe the functionality of these units we have broken this manual into the following sections: System Overview – A basic description of a CalAmp TTU-2900™. This includes a description of roles and responsibilities of each of the CalAmp components as well as a brief overview of the wireless data technologies used by the LMU- 3640™. Hardware Overview – Describes the physical characteristics and interfaces of the TTU-2900™. Installation and Verification – Provides guidance for the installation of the TTU-2900™ versions in a vehicle and instructions on how to verify the installation is performing adequately. 1.2About The Reader Contents 1Introduction 1.1About This Manual 1.2About The Reader 1.3About CalAmp 1.4About the CalAmp Location Messaging Unit - TTU-2900™ 2 System Overview 2.1Overview 2.2Component Descriptions 2.2.1Backend Software 2.2.2LMU Manager 2.2.3LM Direct Server 2.2.4Wireless Data Network 2.2.5 TTU-2900™ 2.2.6 Host Device – Laptop/PDA or MDT 2.3Wireless Data Primer 2.3.1SMS (Short Message Service) 2.3.2LTE (Long-Term Evolution) 3 Hardware Overview 3.1Location Messaging Unit-TTU-2900™ 3.1.1TTU-2900™ Handling Precautions 3.1.2Battery Back-up devices 3.1.3Environmental Specifications 3.1.4Physical Specifications 3.2TTU-2900™ Connectors 3.2.1I/O Connector 3.2.2VBUS Connector 3.2.3Accessories 3.3GPS Receiver 3.4I/O Descriptions 3.4.1Internal Buzzer 3.4.23-Axis Accelerometer Input 3.4.3Ignition and Inputs 3.4.4Outputs 3.4.5Serial Streams 3.4.6Status LEDs 4Configuration of the Vehicle Bus Interface 4.1VBU2 Mode Configuration and Testing Instructions 5 Configuration and Activation 5.1Quick Start - General Config 5.2Activating LTE Using AT Commands 5.3Preparing for Installation 5.4Plan The Installation 5.4.1Size and Placement of LMU Unit 5.4.2Access to the SIM (Subscriber Identity Module) Card 5.4.3Protection from Heat 5.4.4Visibility of Diagnostic LEDs 5.4.5Cable Length 5.4.6Moisture and Weather Protection 5.4.7Preventing Accidental or Unauthorized Modification 5.5Installing the LMU in a Vehicle 5.5.1Place the TTU-2900 in the vehicle. 5.5.2Connect power, ignition, and ground. 5.5.3Typical Connection Sequence 5.6Installation Verification 5.6.1Comm Verification 5.6.2GPS Verification 5.6.3Inbound Verification 5.6.4Verification via SMS 6 CalAmp Locations 7License Agreement 8Limited Warranty 9Regulatory Information 7/21/2020TTU-2900 Hardware & Installation Guide - PULS Wiki 2/29 In order to limit the size and scope of this manual, the following assumptions have been made about the reader. 1.You are familiar with GPS concepts and terminology 2.You have some experience with installing equipment in vehicles 3.You are familiar with the use of AT Commands 4.You are familiar with the use of terminal programs such as HyperTerminal or PuTTY 1.3About CalAmp CalAmp (NASDAQ: CAMP) is a telematics pioneer leading transformation in a global connected economy. We help reinvent businesses and improve lives around the globe with technology solutions that streamline complex IoT deployments and bring intelligence to the edge. Our software applications, scalable cloud services, and intelligent devices collect and assess business-critical data from mobile assets, cargo, companies, cities and people. We call this The New How, powering autonomous IoT interaction, facilitating efficient decision making, optimizing resource utilization, and improving road safety. CalAmp is headquartered in Irvine, California and has been publicly traded since 1983. LoJack is a wholly owned subsidiary of CalAmp. For more information, visit calamp.com, or LinkedIn, Twitter, YouTube or CalAmp Blog. 1.4About the CalAmp Location Messaging Unit - TTU-2900™ The CalAmp Location and Messaging unit-TTU-2900™ is a mobile device that resides in private, commercial or government vehicles. The TTU-2900™ is a single box enclosure incorporating a processor, a GPS receiver, a wireless data modem, and a vehicle-rated power supply. The TTU-2900™ also supports inputs and outputs to monitor and react to the vehicular environment and/or driver actions.. The TTU-2900™ collects, stores and transmits vehicular and location data over a designated wireless network including LTE and HSPA. Vehicular and location data are transmitted to a customized software application that has been designed to receive, acknowledge, process, store, and respond to this data. Unit location and vehicular information is sent at pre-determined intervals, on demand, or when pre-programmed vehicular conditions are met. Transmission of data are sent immediately when in wireless network coverage and stored for later transmission when out of the wireless coverage area. SMS messaging can be used as an alternative or redundant communication backup. The TTU-2900™ is designed to support a variety of custom fleet applications starting with basic automatic vehicle location and including applications requiring more sophisticated features such as geo-fencing, speed and mileage monitoring, third party security monitoring, dynamic reporting routines, and an array of exception alerts. TTU-2900™ a…

Text truncated - open the document above for the full version.

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Subject: Request for Short Term Confidentiality FCC ID: APV-2900MB To Whom It May Concern: In accordance with §0.457(d) and §0.459 of CFR 47, Full Company Name hereby requests short term confidentiality for documents filed under the following exhibit types: 1. External Photographs 2. Internal Photographs 3. User / Instruction Manual 4. Test Set-up Photographs Until the product will be publicly announced. Short term confidentiality release date / period: 180 days from grant issue date These items contain detailed system and equipment description and related information about the product which Full Company Name considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Full Company Name also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are informed and aware of our obligation that we have to inform the involved TCB in written and in due time if we intend to market the product prior to the above specified confidentiality release date so that the short term confidentiality classification can be reset prior to product launch. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Full Name: Imad Rizk Position / Title: Certification Manager Place of Issue: 2177 Salk Ave Carlsbad, Ca 92008. USA Date: January 28 2021

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Subject: Request for Permanent Confidentiality FCC ID: APV-2900MB To Whom It May Concern: In accordance with §0.457(d) and §0.459 of CFR 47, and KDB 726920, Full Company Name hereby requests permanent confidentiality for documents filed under the following exhibit types: 1. Block Diagram 2. Schematic Diagram 3. Part List 4. Operational Description These items contain detailed system and equipment description and related information about the product which Full Company Name considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Full Company Name also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, Full Name: Imad Rizk Position / Title: Certification Manager Place of Issue: 2177 Salk Ave Carlsbad, Ca 92008. USA Date: January 28 2021

Validity of Test Results from Testing / Certification of the Integrated Module To Whom It May Concern: We, CalAmp, 2200 Faraday Ave, Suite 220, Carlsbad CA 92008, USA do hereby declare that the test results from conducted and radiated tests applied to the radio module: Manufacturer: Quectel Model: BG96 FCC ID: XMR201707BG96 and IC ID: 10224A-201709BG96 Which is incorporated in our host equipment: Manufacturer: CalAmp Model: TTU2900MB FCC ID: APV-2900MB and IC ID: 5943C-2900MB And as reported in module test report(s) Report Number: R1811A0536-R1 Issue Date: 02-26-2019 (Part 22 Cat M1) Report Number: R1811A0536-R2 Issue Date: 02-26-2019 (Part 24 CAT M1) Report Number: R1811A0536-R3 Issue Date: 02-26-2019 Part 27 Cat M1) Report Number: R1811A0536-R4 Issue Date: 02-26-2019 (Part 22 NB-IOT) Report Number: R1811A0536-R5 Issue Date: 02-26-2019 (Part 24 NB-IOT) Report Number: R1811A0536-R6 Issue Date: 02-26-2019 (Part 27 NB-IOT) And related original reports Report Number: RXA1706-0199RF01R1, Issue Date: 07-12-2017 Report Number: RXA1706-0199RF02R1, Issue Date: 07-12-2017 Report Number: RXA1706-0199RF03R1, Issue Date: 07-12-2017 Report Number: RXA1706-0199RF04R1, Issue Date: 07-12-2017 Report Number: RXA1706-0199RF08, Issue Date: 08-29-2017 Report Number: RXA1706-0199RF08, Issue Date: 08-29-2017 Report Number: RXA1706-0199RF08, Issue Date: 08-29-2017 Report Number: RXA1706-0199RF08, Issue Date: 08-29-2017 Accurately represent the test results under the new conditions when the identified radio module is integrated in the Identified host equipment. By integration of the said radio module into the identified host equipment no changes were Made to it or by external adaptation circuitry that impacts the validity of the results of the original module’s test reports. Sincerely, Full Name: Imad Rizk Position / Title: Sr. Manager Certifications Place of Issue: 2200 Faraday Ave, Suite 220 Carlsbad, Ca 92008. USA Date: February 19 2021

Letter of Authorization and Anti- Drug Statement Product Name: Weatherproof Telematics Gateway Built for Rugged Environments Model Number: TTU2900MB FCC ID: APV-2900MB We authorize: CETECOM Inc., to act on our behalf on all matters concerning the above named equipment. We declare that CETECOM Inc. is allowed to forward all information related to the approval project to the Federal Communications Commission and discuss any issues concerning the approval application. The applicant must certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti- Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. Does the applicant or authorized agent so certify? ☒ Yes I certify that I am authorized to sign this application. All of the statements herein and the exhibits attached hereto, are true and correct to the best of my knowledge and belief. In accepting a Grant of Equipment Authorization as a result of the representations made in this application, the applicant is responsible for (1) labeling the equipment with the exact FCC ID specified in this application, (2) compliance statement labeling pursuant to the applicable rules, and (3) compliance of the equipment with the applicable technical rules. If the applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC's technical requirements. Authorizing an agent to sign this application, is done solely at the applicant's discretion; however, the applicant remains responsible for all statements in this application. If an agent has signed this application on behalf of the applicant, a written letter of authorization which includes information to enable the agent to respond to the above section 5301 (Anti-Drug Abuse) Certification statement has been provided by the applicant. It is understood that the letter of authorization must be submitted to the FCC upon request, and that the FCC reserves the right to contact the applicant directly at any time. Sincerely Full Name: Imad Rizk Position / Title: Sr. Manager Certification Place of Issue: 2177 Salk Ave Carlsbad, Ca 92008. USA Date: Feb 23, 2021

REVISIONS UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ARE: FRACTIONS DECIMALS ANGLES ±1/32 .XX ±.01 ±0°30’ .XXX ± .005 USED ON DRAWN: CHECKED: ISSUED: TITLE DO NOT SCALE DRAWING SIZE CAGE CODE DWG NO. REV A 6T925 SHEET 1 OF 1 SCALE ITEM NO. QTY REQD IDENTIFYING NO. DESCRIPTION MKTG: 5 1 NOTES: UNLESS OTHERWISE SPECIFIED 1. APPLICABLE STANDARDS / SPECIFICATIONS; MIL-STD-100E, ENGINEERING DRAWING PRACTICES. ANSI Y14.5M-1982, DIMENSIONS AND TOLERANCES. 2. FONT (TYPICAL) : CALIBRI (VARIOUS SIZES), ARIAL (VARIOUS SIZES). IF REQUIRED, BARCODE FORMAT : CODE 128 OR DATA MATRIX ECC200, BLACK INK 3. IF REQUIRED, DATE CODE SHALL BE DEFINED AS : WWYY WW – TWO DIGIT WORK WEEK YY – TWO DIGIT YEAR 4. IF REQUIRED, CURRENT DATE SHALL BE DEFINED AS : MM/DD/YYYY MM – MONTH DD – DAY YYYY – YEAR 5. MATERIAL MUST BE LEAD (Pb) FREE PER THE EUROPEAN UNION’S RESTRICTION OF HAZARDOUS SUBSTANCE (RoHS) DIRECTIVE. 6. COUNTRY OF ORIGIN (COO) IN THE LABEL IMAGE WILL BE REPLACED BY THE COUNTRY LISTED PER THE TABLE BELOW ON ACTUAL PRINTED LABEL. LABEL BLANK, 1.75 X 1.0, SILVER MYLAR, ARGOS 79-00052 LABEL FILE: COO Label Information Assembled in China Assembled in Taiwan 6 Assembled in Malaysia Assembled in Mexico Assembled in USA REV ECO NO. DESCRIPTION DATE APPROVED A 69348 PRODUCTION RELEASE 11/20/2020 E. MOORE LABEL MARKING, UNIT, TTU2900, APOLLO, LTE CAT M, WW, BLUETOOTH, 6200MAH BATT, RS232, GEN-HW A TTU2900MB-YR00-G1000 Elec. File: 136108_A.docx 136108_A_TTU2900MB-YR00-G1000_DB.btw SEE OMNIFY E. MOORE 11/20/2020 SEE OMNIFY 136108 3 6

Radio Frequency Exposure Evaluation Report FOR: CalAmp Model Number: TTU2900MB Product Description: Solar-based telematics gateway FCC ID: APV-2900MB IC ID: 5843C-2900MB Per: CFR Part Part1 (1.1307 &1.1310), Part 2 (2.1091), FCC KDB 447498 D01 General RF Exposure Guidance v06 ISEDC RSS-102 Issue 5 Report number: EMC_CALAM-118-21001_FCC_ISED_MPE DATE: 2021-02-19 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V5.0 2015-10-27 © Copyright by CETECOM Test Report #: EMC_CALAM-118-21001_FCC_ISED_MPE FCC ID: APV-2900MB Date of Report 2021-02-19 Page 2 of 8 IC ID: 5843C-2900MB Page 2 of 8 1 Assessment This RF Exposure evaluation report provides evidence for compliance of the below identified device with the RF Exposure limits for mobile devices as defined in FCC CFR Part 1 (1.1307 &1.1310), Part 2 (2.1091) and IC standard RSS-102 issue 5 under worst case conditions (measured or rated RF output power, antenna gain, distance towards human body, multiple transmitter information as presented by the applicant). In addition, maximum antenna gain or minimum distance towards the human body is calculated respectively, where relevant. The device meets the limits as stipulated by the above given FCC and IC rule parts based on available specifications for worst case conditions at 20cm distance to the body. Company Description Model # CalAmp Solar-based telematics gateway TTU2900MB Report reviewed by: TCB Evaluator 2021-02-19 Compliance Cindy Li (Lab Manager) Date Section Name Signature Responsible for the Report: 2021-02-19 Compliance Yuchan Lu (Test Engineer) Date Section Name Signature Test Report #: EMC_CALAM-118-21001_FCC_ISED_MPE FCC ID: APV-2900MB Date of Report 2021-02-19 Page 3 of 8 IC ID: 5843C-2900MB Page 3 of 8 2 Administrative Data 2.1 Identification of the Testing Laboratory Issuing the Test Report Company Name: CETECOM Inc. Department: Compliance Street Address: 411 Dixon Landing Road City/Zip Code Milpitas, CA 95035 Country USA Telephone: +1 (408) 586 6200 Fax: +1 (408) 586 6299 Lab Manager: Cindy Li Responsible Project Leader: Cathy Palacios 2.2 Identification of the Client / Manufacturer Client’s Name: CalAmp Street Address: 2200 Faraday Avenue, Suite 220 City/Zip Code Carlsbad, CA 92008 Country USA 2.3 Identification of the Manufacturer Manufacturer’s Name: Same as Client Manufacturers Address: City/Zip Code Country Test Report #: EMC_CALAM-118-21001_FCC_ISED_MPE FCC ID: APV-2900MB Date of Report 2021-02-19 Page 4 of 8 IC ID: 5843C-2900MB Page 4 of 8 3 Equipment under Assessment Marketing name: TTU2900MB HW Version : REV A SW Version : 8.5 Hardware Version Identification Number (HVIN): TTU2900MB Product Marketing Name (PMN): TTU2900MB Regulatory Band:  Cellular Module:  LTE BAND 2: 1850.7 ~ 1909.3 MHz  LTE BAND 4: 1710.7 ~ 1754.3 MHz  LTE BAND 5: 824.7 ~ 848.3 MHz  LTE BAND 12: 699.7 ~ 715.3 MHz  LTE BAND 13: 779.5 ~ 784.5 MHz  LTE BAND 25: 1850.7 ~ 1914.3 MHz  LTE BAND 26: 814.7 ~ 848.3 MHz  BLE:  Nominal band: 2400 MHz – 2483.5 MHz;  Center to center: 2402 MHz (ch 0) – 2480 MHz (ch 39), 40 channels Integrated Module Info:  GSM, LTE  Manufacture: Quectel  Module name/number: BG96  FCC ID: XMR201707BG96  IC ID: 10224A-201709BG96  BLE  Manufacture: Texas Instruments  Module name/number: CC2640 Antenna Type:  Cellular:  Antenna maximum gain: o LTE Band 2: 3.1 dBi o LTE Band 4: 3.1 dBi o LTE Band 5: 1.6 dBi o LTE Band 12: 1.6 dBi o LTE Band 13: 1.6 dBi o LTE Band 25: 3.1 dBi Test Report #: EMC_CALAM-118-21001_FCC_ISED_MPE FCC ID: APV-2900MB Date of Report 2021-02-19 Page 5 of 8 IC ID: 5843C-2900MB Page 5 of 8 o LTE Band 26: 1.6 dBi  BLE:  Antenna gain: 1.88 dBi Maximum Conducted Output Power:  Cellular: From modular grant [Watts]:  LTE Band 2: 0.247  LTE Band 4: 0.175  LTE Band 5: 0.242  LTE Band 12: 0.233  LTE Band 13: 0.246  LTE Band 25: 0.284  LTE Band 26:0.239  BLE: From measurement [Watts]: 0.00324 Power Supply/ Rated Operating Voltage Range: Vmin: 8 VDC/ Vnom: 12 VDC / Vmax: 32 VDC Operating Temperature Range: Low -30⁰C, Nominal 25⁰C, High 70⁰C Sample Revision: Prototype Unit; Production Unit; Pre-Production Test Report #: EMC_CALAM-118-21001_FCC_ISED_MPE FCC ID: APV-2900MB Date of Report 2021-02-19 Page 6 of 8 IC ID: 5843C-2900MB Page 6 of 8 4 RF Exposure Limits and FCC and IC Basic Rules For the specific described radio apparatus the following basic limits and rules apply for both, FCC and IC where not indicated differently. 4.1 Power Density Limits acc. to FCC 1.1310(e) / RSS-102 i5, cl. 4: FCC Frequency Range (MHz) Power density (mW/cm 2 ) Averaging time (minutes) 300 – 1500 f (MHz) /1500 30 1500 – 100000 1.0 30 IC 300 – 6000 0.02619 x f (MHz) 0.6834 6 4.2 Routine Environmental Evaluation Categorical Exclusion Limits acc. to FCC 2.1091(c) / RSS-102, cl. 2.5 (rounded to 1 decimal point): FCC operating frequency < 1.5GHz: excluded if ERP < 1.5W / 31.8dBm (EIRP: 33.9 dBm); operating frequency > 1.5GHz: excluded if ERP < 3.0W / 34.8dBm (EIRP: 36.9 dBm); IC 300MHz < = operating frequency < 6 GHz: excluded if EIRP < 0.0131 x f (MHz) 0.6834 W 4.3 RF Exposure Estimation (MPE Estimation) Having available the source based average output power and peak antenna gain or the ERP/EIRP of the specified device and for a known minimum distance of its radiating structures from the body of persons according to its use cases (at least 20cm) the power density at that distance can be estimated by the following formula for plane-wave equivalent conditions (far-field conditions), when ground reflection is neglected. 2 4R PG S   where: S = power density (mW/cm 2 or W/m 2 ) P = power input to the antenna (mW or W) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (cm or m) Test Report #…

Text truncated - open the document above for the full version.

RF TEST REPORT Applicant Quectel Wireless Solutions Co., Ltd. FCC ID XMR201707BG96 Product Quectel BG96 Brand Quectel Model BG96 Report No. RXA1706-0199RF01R1 Issue Date July 12,2017 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC CFR47 Part 2 (2017)/ FCC CFR 47 Part 22H (2017). The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Jiangpeng Lan Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86‐021‐50791141/2/3 FAX: +86‐021‐50791141/2/3‐8000 FCC RF Test Report Report No: RXA1706-0199RF01R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-001R Page 2 of 91 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. TABLE OF CONTENT 1. Test Laboratory ...................................................................................................................................... 4 1.1. Notes of the Test Report ............................................................................................................... 4 1.2. Test facility ..................................................................................................................................... 4 1.3. Testing Location ............................................................................................................................ 5 2. General Description of Equipment under Test ....................................................................................... 6 3. Applied Standards .................................................................................................................................. 7 4. Test Configuration .................................................................................................................................. 8 5. Test Case Results ................................................................................................................................ 10 5.1. RF Power Output ......................................................................................................................... 10 5.2. Effective Radiated Power ............................................................................................................ 17 5.3. Occupied Bandwidth ................................................................................................................... 23 5.4. Band Edge Compliance ............................................................................................................... 37 5.5. Peak-to-Average Power Ratio (PAPR) ....................................................................................... 51 5.6. Frequency Stability ...................................................................................................................... 54 5.7. Spurious Emissions at Antenna Terminals ................................................................................. 60 5.8. Radiates Spurious Emission ....................................................................................................... 70 6. Main Test Instruments ......................................................................................................................... 88 ANNEX A: EUT Appearance and Test Setup .............................................................................................. 89 A.1 EUT Appearance ......................................................................................................................... 89 A.2 Test Setup .................................................................................................................................... 91 FCC RF Test Report Report No: RXA1706-0199RF01R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-001R Page 3 of 91 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Summary of measurement results No. Test Type Clause in FCC rules Verdict 1 RF power output 2.1046 PASS 2 Effective Radiated Power 22.913(a)(2) PASS 3 Occupied Bandwidth 2.1049 PASS 4 Band Edge Compliance 2.1051 / 22.917(a) PASS 5 Peak-to-Average Power Ratio 22.913(d)/ KDB 971168 D01(5.7) PASS 6 Frequency Stability 2.1055 / 22.355 PASS 7 Spurious Emissions at Antenna Terminals 2.1051 / 22.917(a) PASS 8 Radiates Spurious Emission 2.1053 / 22.917 (a) PASS Date of Testing: June 24, 2017~July 3, 2017 Note: PASS: The EUT complies with the essential requirements in the standard. FAIL: The EUT does not comply with the essential requirements in the standard. FCC RF Test Report Report No: RXA1706-0199RF01R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-001R Page 4 of 91 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1. Test Laboratory 1.1. Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. This report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. 1.2. Test facility CNAS (accreditation number: L2264) TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS). FCC (recognition number is 428261) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements.…

Text truncated - open the document above for the full version.

FCC RF Test Report Report No: RXA1706-0199RF01R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-001R Page 51 of 91 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 5.5. Peak-to-Average Power Ratio (PAPR) Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement Measure the total peak power and record as P Pk . And measure the total average power and record as P Avg . Both the peak and average power levels must be expressed in the same logarithmic units (e.g., dBm). Determine the PAPR from: PAPR (dB) = P Pk (dBm) - P Avg (dBm). Test Setup Limits According to the Sec. 22.913(d), The peak-to-average ratio (PAR) of the transmission must not exceed 13 dB. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 0.4 dB. FCC RF Test Report Report No: RXA1706-0199RF01R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-001R Page 52 of 91 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. Test Results Mode Channel Frequency (MHz) Peak (dBm) Avg (dBm) PAPR (dB) Limit (dB) Conclusion GPRS 850 (GMSK) 128 824.2 30.69 30.01 0.68 ≤13 PASS 190 836.6 30.82 30.11 0.71 ≤13 PASS 251 848.8 30.92 30.28 0.64 ≤13 PASS EGPRS 850 (8-PSK) 128 824.2 26.84 26.05 0.79 ≤13 PASS 190 836.6 26.97 26.06 0.91 ≤13 PASS 251 848.8 27.00 26.19 0.81 ≤13 PASS LTE Band 5 Modulation Bandwidth (MHz) Channel Frequency (MHz) Peak (dBm) Avg (dBm) PAPR (dB) Limit (dB) Conclusion QPSK 1.4 20407 824.7 32.89 22.62 10.27 ≤13 PASS 20525 836.5 32.98 22.71 10.27 ≤13 PASS 20643 848.3 34.59 22.86 11.73 ≤13 PASS 3 20415 825.5 32.71 22.70 10.01 ≤13 PASS 20525 836.5 32.95 22.73 10.22 ≤13 PASS 20635 847.5 34.52 22.90 11.62 ≤13 PASS 5 20425 826.5 32.69 22.68 10.01 ≤13 PASS 20525 836.5 33.21 22.69 10.52 ≤13 PASS 20625 846.5 32.99 22.85 10.14 ≤13 PASS 10 20450 829 32.56 22.65 9.91 ≤13 PASS 20525 836.5 32.60 22.64 9.96 ≤13 PASS 20600 844 32.87 22.81 10.06 ≤13 PASS 16QAM 1.4 20407 824.7 33.44 22.67 10.77 ≤13 PASS 20525 836.5 34.24 23.20 11.04 ≤13 PASS 20643 848.3 34.79 23.00 11.79 ≤13 PASS 3 20415 825.5 34.01 22.70 11.31 ≤13 PASS 20525 836.5 34.24 23.25 10.99 ≤13 PASS 20635 847.5 35.15 23.04 12.11 ≤13 PASS 5 20425 826.5 33.86 22.67 11.19 ≤13 PASS 20525 836.5 34.41 23.20 11.21 ≤13 PASS 20625 846.5 33.85 23.00 10.85 ≤13 PASS 10 20450 829 33.35 22.65 10.70 ≤13 PASS 20525 836.5 33.28 23.16 10.12 ≤13 PASS 20600 844 32.99 22.97 10.02 ≤13 PASS FCC RF Test Report Report…

Text truncated - open the document above for the full version.