APV-4230HBTVehicle tracking unit with GPS, GSM/GPRS/HSPA and Bluetooth

1/28/2015LMU­42x0 Hardware & Installation Guide ­ PULS Wiki https://puls.calamp.com/wiki/LMU­42x0_Hardware_%26_Installation_Guide1/47 LMU­42x0 Hardware & Installation Guide 1 change (https://puls.calamp.com/w/index.php?title=LMU­ 42x0_Hardware_%26_Installation_Guide&oldid=4791&diff=cur) in this version is pending review. The stable version (https://puls.calamp.com/w/index.php?title=LMU­42x0_Hardware_%26_Installation_Guide&stable=1) was checked (https://puls.calamp.com/w/index.php?title=Special:Log&type=review&page=LMU­ 42x0_Hardware_%26_Installation_Guide) on 10 June 2014. Contents 1 Introduction 1.1 About This Manual 1.2 About The Reader 1.3 About CalAmp 1.4 About the CalAmp Location Messaging Unit­LMU­42x0™ 2 System Overview 2.1 Overview 2.2 Component Descriptions 2.2.1 Wireless Data Network 2.2.2 LMU­42x0™ 2.2.3 LM Direct™ Server 2.2.4 Backend Software 2.2.5 PULS™ 2.2.6 LMU Manager™ 3 Hardware Overview 3.1 Location Messaging Unit­LMU­42x0™ 3.1.1 LMU­42x0™ Handling Precautions 3.1.2 Battery Back­up devices 3.1.3 Environmental Specifications 3.2 Location Messaging Unit­ 4200™ & 4250™ 3.3 LMU­42x0™Connectors 3.3.1 Power Connector 3.3.2 I/O Connector 3.3.3 Expansion Port 3.3.4 Serial Interface Connectors 3.3.5 Expansion Interface 3.3.6 Serial Adapter 3.3.7 Accessories 3.4 GPS Receiver 3.5 RF Connector 3.6 I/O Descriptions 3.6.1 3­Axis Accelerometer Input 3.6.2 Ignition and Inputs 3.6.3 Outputs 3.6.4 Status LEDs 4 Configuration and Activation 4.1 Quick Start ­ General Config 4.2 Auto provisioning of GSM or HSPA LMUs 4.3 Activating GSM or HSPA LMU using AT Commands 4.4 Accessing the SIM 4.5 Activating a CDMA LMU­42x0™ 1/28/2015LMU­42x0 Hardware & Installation Guide ­ PULS Wiki https://puls.calamp.com/wiki/LMU­42x0_Hardware_%26_Installation_Guide2/47 4.5.1 Activating a CDMA LMU­42x0™ – Verizon 4.5.2 Activating a CDMA LMU­42x0™ – Sprint 5 Installing the LMU 5.1 Preparing for Installation 5.2 Plan The Installation 5.2.1 Size and Placement of LMU Unit 5.2.2 Placement of Antennas 5.2.3 Access to the SIM (Subscriber Identity Module) Card 5.2.4 Protection from Heat 5.2.5 Visibility of Diagnostic LEDs 5.2.6 Cable Length 5.2.7 Moisture and Weather Protection 5.2.8 Preventing Accidental or Unauthorized Modification 5.3 Installing the LMU in a Vehicle 5.3.1 Place the LMU unit in the vehicle. 5.3.2 Connect power, ignition, and ground. 5.3.3 Place the GPS antenna. 5.3.4 Mount the Comm. Antenna. 5.3.5 Typical Connection Sequence 5.4 Installation Verification 5.4.1 Comm Verification 5.4.2 GPS Verification 5.4.3 Inbound Verification 5.4.4 Verification via SMS 6 License Agreement 7 Limited Warranty 8 Regulatory Information LMU­42x0™ Hardware and Installation Guide IMPORTANT: DO NOT INSTALL OR USE THE SOFTWARE OR DOCUMENTATION UNTIL YOU HAVE READ AND AGREED TO THE LICENSE AGREEMENT AND REVIEWED THE LIMITED WARRANTY AND REGULATORY INFORMATION. 1 Introduction 1/28/2015LMU­42x0 Hardware & Installation Guide ­ PULS Wiki https://puls.calamp.com/wiki/LMU­42x0_Hardware_%26_Installation_Guide3/47 Welcome to the LMU­42x0™ Hardware and Installation Guide. This manual is intended to give you information on the basic setup and installation of the CalAmp LMU­42x0™ product(s) including hardware descriptions, environmental specifications, wireless network overviews and device installation. 1.1 About This Manual The LMU­42x0™ is one of the most flexible economy mobile tracking hardware products available. In order to accurately describe the functionality of these units we have broken this manual into the following sections: System Overview – A basic description of a CalAmp LMU­42x0™ based tracking system. This includes a description of roles and responsibilities of each of the CalAmp components as well as a brief overview of the wireless data technologies used by the LMU­42x0™. Hardware Overview – Describes the physical characteristics and interfaces of the LMU­42x0™. Installation and Verification – Provides guidance for the installation of the LMU­42x0™ in a vehicle and instructions on how to verify the installation is performing adequately. 1.2 About The Reader In order to limit the size and scope of this manual, the following assumptions have been made about the reader. You are familiar with GPS concepts and terminology You have some experience with installing equipment in vehicles You are familiar with the use of AT Commands You are familiar with the use of terminal programs such as HyperTerminal or PuTTY 1.3 About CalAmp CalAmp is a leading provider of wireless communications products that enable anytime/anywhere access to critical information, data and entertainment content. With comprehensive capabilities ranging from product design and development through volume production, CalAmp delivers cost­effective high quality solutions to a broad array of customers and end markets. CalAmp is the leading supplier of Direct Broadcast Satellite (DBS) outdoor customer premise equipment to the U.S. satellite television market. The Company also provides wireless data communication solutions for the telemetry and asset tracking markets, private wireless networks, public safety communications and critical infrastructure and process control applications. For additional information, please visit the Company’s website at www.calamp.com (http://www.calamp.com/) . 1.4 About the CalAmp Location Messaging Unit­LMU­42x0™ The CalAmp Location and Messaging Unit­LMU­42x0™ (LMU­42x0™) is a mobile device that resides in private, commercial or government vehicles. The LMU­42x0™ is a single box enclosure incorporating a processor, a GPS receiver, a wireless data modem, and a vehicle­rated power supply. The LMU­42x0™ also supports inputs and outputs to monitor and react to the vehicular environment and/or driver actions. Flexibility 1/28/2015LMU­42x0 Hardware & Installation Guide ­ PULS Wiki https://puls.calamp.com/wiki/LMU­42x0_Hardware_%26_Installation_Guide4/47 The LMU­42x0™ features CalAmp's industry leading advanced on­board alert engine that …

Text truncated - open the document above for the full version.

A E R C E P T D A T A R A D I O L A N D C E L L O M E G A S MA R T L I N K www.calamp.com CalAmp / Mobile resource Management MRM/M2M Products 2177 Salk Ave, STE 200 Carlsbad, CA 92008 PH: (760) 438-9010 – Fax: (760) 438-5835 February 10, 2015 TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Re: FCC ID: APV-4230HBT IC: 5843C-4230HBT M/N: LMU4230H Dir Sir and Madam, The LMU4230H is fleet management and tracking device that resides in private, it is a single box enclosure incorporating a processor, a GPS receiver, a wireless data modem, vehicle-rated power supply and Vehicle bus interface. The LMU4230H also supports inputs and outputs to monitor and react to the vehicular environment and/or driver actions. The LMU4230H contains the same BT/GSM/HSPA radios already certified by TUV under model: LMU30H30BT3 with FCC ID: APV-3030HBT and IC ID: 5843C-3030HBT Sincerely, Product Certification Manager Imad Rizk Phone number: (760) 814-9697 Email: [email protected]

TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121‐2912 Phone: 858 678 1400 FAX: 858 546 0364 TÜV SÜD America Inc. (San Diego) February 09, 2015 TUV SUD BABT Octagon House, Concorde Way Segensworth Rd N, Fareham PO15 5RL RE: FCC ID APV‐4230HBT IC: 5843C‐4230HBT M/N: LMU4230H By my signature below, I attest:  That the Cinterion Wireless module, model: ESH5‐US, which is integrated in this device, is unchanged.  That the original test data from CETECOM GmbH Test Report No.: 6‐014712‐9‐3A and 6‐147‐ 12‐9‐3b according to FCC Part 22H/24E and RSS‐132/133 remain valid and applicable to Model LMU4230H and is/are representative of the compliance for this device.  That the original test data from CETECOM GmbH Test Report No.: 6‐014712‐9‐3A and 6‐147‐ 12‐9‐3b are compliant to the latest version of IC radio standards applied for (RSS‐133 Issue 6 and RSS‐132 Issue 3). Sincerely, Juan Manuel Gonzalez Commercial wireless EMC Lab Manager

A E R C E P T D A T A R A D I O L A N D C E L L O M E G A S MA R T L I N K www.calamp.com CalAmp / Mobile resource Management MRM/M2M Products 2177 Salk Ave, STE 200 Carlsbad, CA 92008 PH: (760) 438-9010 – Fax: (760) 438-5835 February 4, 2015 TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Re: FCC ID: APV-4230HBT IC: 5843C-4230HBT Dir Sir and Madam, We CalAmp 2177 Salk Ave, STE 200, Carlsbad, CA 92008 hereby authorize Juan Manuel Gonzalez TUV SUD America, Inc. 10040 Mesa Rim Road, San Diego, CA 92121 Tel: (858) 678-1466 to act as our agent in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. This authorization expire on February 4, 2016 Sincerely, Product Certification Manager Imad Rizk Phone number: (760) 814-9697 Email: [email protected]

A E R C E P T D A T A R A D I O L A N D C E L L O M E G A S MA R T L I N K www.calamp.com CalAmp / Mobile resource Management MRM/M2M Products 2177 Salk Ave, STE 200 Carlsbad, CA 92008 PH: (760) 438-9010 – Fax: (760) 438-5835 TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Confidentiality Request FCC ID: APV-4230HBT Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, CalAmp Wireless networks hereby requests permanent confidential treatment of information accompanying this application as: - Block Diagram - Operation description - Schematic - Part list Also hereby requests short-term confidential treatment of information accompanying this application as outlined below for a period of 180 days: - Internal photos - External photos The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Sincerely, January 28 2015 Product Certification Manager Imad Rizk Phone number: (760) 814-9697 Email: [email protected]

FCC ID APV‐4230HBT IC: 5843C‐4230HBT

UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ARE: FRACTIONS DECIMALS ANGLES ±1/32 .XX ±.01 ±0°30’ .XXX ± .005 USED ON REVISIONS MATERIAL FINISH DRAWN: CHECKED: ISSUED: TITLE DO NOT SCALE DRAWING SIZE CAGE CODE DWG NO. REV A 6T925 SHEET 1 OF 1 SCALE ITEM NO. QTY REQD IDENTIFYING NO. DESCRIPTION MKTG: 1 1 LABEL BLANK, COATED MATTE, 2.75 X 1.56, 1” SPL 79969-2 NOTES: UNLESS OTHERWISE SPECIFIED 1. APPLICABLE STANDARDS / SPECIFICATIONS; MIL-STD-100E, ENGINEERING DRAWING PRACTICES. ANSI Y14.5M-1982, DIMENSIONS AND TOLERANCES. 2. FONT : BARCODE FORMAT 39, BLACK INK 3. DATE CODE SHALL BE DEFINED AS : WWYY WW – TWO DIGIT WORK WEEK YY – TWO DIGIT YEAR 4. MATERIAL MUST BE LEAD (Pb) FREE PER THE EUROPEAN UNION’S RESTRICTION OF HAZARDOUS SUBSTANCE (RoHS) DIRECTIVE. A. HARGITAI MM/DD/YYYY D. PATEL 01/23/2015 A. ANGELES MM/DD/YYYY 13xxxx-G1000 A REV ECO NO. DESCRIPTION DATE APPROVED A PRODUCTION RELEASE 01/23/2015 LABEL, UNIT MARKING, LMU4230, GEMALTO HSPA, JPOD, BLUETOOTH, INT, GEN-HW LMU4230H-JB00-G1000 Elec. File: 13xxxx-G1000_A.doc 3 WWYY nnnnnnnnnn nnnnnnnnnnnnnnn P/N: LMU4230H ESN: IMEI: FCC ID: APV-4230HBT IC: 5843C-4230HBT This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Assembled in China CC: JB00-G1000

FCC ID APV‐4230HBT IC: 5843C‐4230HBT

  

 

TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121‐2912 Phone: 858 678 1400 FAX: 858 546 0364 February 2, 2015 TUV SUD BABT Octagon House, Concorde Way Segensworth Rd N, Fareham PO15 5RL Attention: Director of Certification RE: Analysis of RF Exposure for Portable use per Title 47, Part 1 Subpart I, §1.1310, Title 47, Part 2 Subpart J, §2.1091 and RSS‐102 Issue 4 March 2010. FCC ID: APV‐4230HBT IC: 5843C‐4230HBT 1. Mobile MPE Calculation Summary using a 20cm separation distance: Mode Output Power Antenna Gain Power Density (mW/m 2 ) GSM/GPRS 850 33.20 dBm (837.0 MHz) ‐9.8 dBi* 0.0435 GSM/GPRS 1900 30.47 dBm (1880.0 MHz) ‐4.5 dBi* 0.0787 WCDMA FDD V 23.84 dBm (826.40 MHz) ‐9.8 dBi* 0.0050 WCDMA FDD II 24.80 dBm (1880.0 MHz) ‐4.5 dBi* 0.0213 Bluetooth 100.4 dBμV/m @ 3 meters 0 dBi 0.00065441 Bluetooth LE 86.6 dBμV/m @ 3 meters 0 dBi 0.00002728 2. Co‐Located Transmitters transmission table: Transmitter type Transmitter type that can transmit at the same time GSM/GPRS 850 Bluetooth GSM/GPRS 850 Bluetooth LE GSM/GPRS 1900 Bluetooth GSM/GPRS 1900 Bluetooth LE WCDMA FDD II Bluetooth WCDMA FDD II Bluetooth LE WCDMA FDD V Bluetooth WCDMA FDD V Bluetooth LE TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121‐2912 Phone: 858 678 1400 FAX: 858 546 0364 3. Simultaneous Transmission MPE (Worst Case Combination): Transmitter type MPE (mw/cm 2 ) Limit (mW/cm 2 ) MPE ratio (MPE/Limit) GSM/GPRS 1900 0.0787 1.0 0.0787 Bluetooth 0.00065441 1.0 0.00065441 Sum of the ratios (should be <1.0)0.07935441 4. Mobile MPE Calculation using a 20cm separation distance (GSM/GPRS 850): Using Power Density formula: Sൌ PG 4πR ଶ where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to isotropic R = distance to the center of radiation of the antenna Maximum peak output power at antenna input terminal: 33.20 (dBm) Maximum peak output power at antenna input terminal: 2089.30 (mW) Antenna gain(typical): ‐9.8 (dBi) Maximum antenna gain: 0.105 (numeric) Prediction distance: 20 (cm) Sourse Based Time Average Duty Cycle: 100 (%) Prediction frequency: 837 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 0.558 (mW/cm 2 ) Power density at prediction frequency: 0.0435 (mW/cm 2 ) Power density at prediction frequency: 0.435 (W/m 2 ) Margin of Compliance: ‐11.08 (dB) 5. Mobile MPE Calculation using a 20cm separation distance (GSM/GPRS 1900): Maximum peak output power at antenna input terminal: 30.47 (dBm) Maximum peak output power at antenna input terminal: 1114.29 (mW) Antenna gain(typical): ‐4.5 (dBi) Maximum antenna gain: 0.355 (numeric) Prediction distance: 20 (cm) Sourse Based Time Average Duty Cycle: 100 (%) Prediction frequency: 1880 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 1.000 (mW/cm 2 ) TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121‐2912 Phone: 858 678 1400 FAX: 858 546 0364 Power density at prediction frequency: 0.0787 (mW/cm 2 ) Power density at prediction frequency: 0.787 (W/m 2 ) Margin of Compliance: ‐11.04 (dB) TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121‐2912 Phone: 858 678 1400 FAX: 858 546 0364 6. Mobile MPE Calculation using a 20cm separation distance (WCDMA FDD II): Maximum peak output power at antenna input terminal: 23.84 (dBm) Maximum peak output power at antenna input terminal: 242.10 (mW) Antenna gain(typical): ‐9.8 (dBi) Maximum antenna gain: 0.105 (numeric) Prediction distance: 20 (cm) Sourse Based Time Average Duty Cycle: 100 (%) Prediction frequency: 826.4 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 0.550 (mW/cm 2 ) Power density at prediction frequency: 0.0050 (mW/cm 2 ) Power density at prediction frequency: 0.050 (W/m 2 ) Margin of Compliance: ‐20.38 (dB) 7. Mobile MPE Calculation using a 20cm separation distance (WCDMA FDD V): Maximum peak output power at antenna input terminal: 24.80 (dBm) Maximum peak output power at antenna input terminal: 302.00 (mW) Antenna gain(typical): ‐4.5 (dBi) Maximum antenna gain: 0.355 (numeric) Prediction distance: 20 (cm) Sourse Based Time Average Duty Cycle: 100 (%) Prediction frequency: 1880 (MHz) MPE limit for uncontrolled exposure at prediction frequency: 1.000 (mW/cm 2 ) Power density at prediction frequency: 0.0213 (mW/cm 2 ) Power density at prediction frequency: 0.213 (W/m 2 ) Margin of Compliance: ‐16.71 (dB) TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121‐2912 Phone: 858 678 1400 FAX: 858 546 0364 8. Mobile MPE Calculation using a 20cm separation distance (Bluetooth): Measured Field Strength ‐‐Radiated: 100.4 (dBuV/m) Maximum peak output power ‐‐Radiated: 0.0032894 (W) Antenna gain(typical): 0.00 (dBi) Maximum antenna gain: 1.00 (numeric) Prediction distance: 20.00 (cm) Prediction frequency: 319.00 (MHz) Limit from table below: 1 (mW/cm 2 ) Power density at prediction frequency: 0.00065441 (mW/cm 2 ) Margin of Compliance: ‐31.84 (dB) 9. Mobile MPE Calculation using a 20cm separation distance (Bluetooth LE): Measured Field Strength ‐‐Radiated: 86.6 (dBuV/m) Maximum peak output power ‐‐Radiated: 0.0001371 (W) Antenna gain(typical): 0.00 (dBi) Maximum antenna gain: 1.00 (numeric) Prediction distance: 20.00 (cm) Prediction frequency: 319.00 (MHz) Limit from table below: 1 (mW/cm 2 ) Power density at prediction frequency: 0.00002728 (mW/cm 2 ) Margin of Compliance: ‐45.64 (dB) *Notes: Power level and worst case channel information for the cellular radio were derived from the test reports of the original filing. Antenna gains information of the cellular radio were derived from a reference cellular module testing using CTIA Over The Air Performance Summation Test Report (7 layers, Inc. Project Name: MUS_CALAMP_1310) provided by the client. Sincerely, Juan M. Gonzalez Name Authorized Signatory Title: Commercial/Wireless EMC Lab Manager

Report No. SC1409996B October 2014 America Report On Application for Grant of Equipment Authorization of the CalAmp Wireless Networks Corp. LMU-3030 GPS Tracking Unit with OBD-II Interface FCC Part 15 Subpart C §15.247 IC RSS-210 Issue 8 December 2010 FCC ID APV-3030HBT IC: 5843C-3030HBT Report No. SC1409996B Page 2 of 54 TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone: 858 678 1400 FAX: 858 546 0364 REPORT ON TEST REPORT NUMBER PREPARED FOR Radio Testing of the CalAmp Wireless Networks Corp. GPS Tracking Unit with OBD-II Interface SC1409996B CalAmp Wireless Networks Corp. 1401 N Rice Ave. Oxnard, CA 93030 CONTACT PERSON Imad Rizk Certification Manager (805) 987-9000 [email protected] PREPARED BY Ferdinand S. Custodio Name Authorized Signatory Title: EMC/Wireless Test Engineer APPROVED BY Chip R. Fleury Name Authorized Signatory DATED October 14, 2014 FCC ID APV-3030HBT IC: 5843C-3030HBT Report No. SC1409996B Page 3 of 54 TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone: 858 678 1400 FAX: 858 546 0364 Revision History SC1409996B CalAmp Wireless Networks Corp. LMU-3030 GPS Tracking Unit with OBD-II Interface DATE OLD REVISION NEW REVISION REASON PAGES AFFECTED APPROVED BY 10/14/2014 Initial Release Chip R. Fleury FCC ID APV-3030HBT IC: 5843C-3030HBT Report No. SC1409996B Page 4 of 54 TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone: 858 678 1400 FAX: 858 546 0364 CONTENTS Section Page No 1 REPORT SUMMARY ............................................................................................................................... 5 1.1 Introduction ................................................................................................................................................ 6 1.2 Brief Summary Of Results ........................................................................................................................... 7 1.3 Product Information ................................................................................................................................... 8 1.4 EUT Test Configuration ............................................................................................................................. 10 1.5 Deviations From The Standard ................................................................................................................. 12 1.6 Modification Record ................................................................................................................................. 12 1.7 Test Methodology ..................................................................................................................................... 12 1.8 Test Facility Location ................................................................................................................................. 12 1.9 Test Facility Registration ........................................................................................................................... 12 2 TEST DETAILS ...................................................................................................................................... 14 2.1 Peak Output Power ................................................................................................................................... 15 2.2 Conducted Emissions ................................................................................................................................ 20 2.3 99% Emission Bandwidth .......................................................................................................................... 21 2.4 Minimum 6 dB RF Bandwidth ................................................................................................................... 26 2.5 Out-Of-Band Emissions - Conducted ........................................................................................................ 30 2.6 Band-Edge Compliance Of Rf Conducted Emissions ................................................................................. 31 2.7 Spurious Radiated Emissions .................................................................................................................... 33 2.8 Radiated Immediate Restricted Bands ..................................................................................................... 41 2.9 Power Spectral Density ............................................................................................................................. 42 2.10 Receiver Spurious Emissions ..................................................................................................................... 46 3 TEST EQUIPMENT USED ...................................................................................................................... 47 3.1 Test Equipment Used ................................................................................................................................ 48 3.2 Measurement Uncertainty ....................................................................................................................... 49 4 DIAGRAM OF TEST SETUP ................................................................................................................... 50 4.1 Test Setup Diagram ................................................................................................................................... 51 5 ACCREDITATION, DISCLAIMERS AND COPYRIGHT ............................................................................... 53 5.1 Accreditation, Disclaimers and Copyright ................................................................................................. 54 FCC ID APV-3030HBT IC: 5843C-3030HBT Report No. SC1409996B Page 5 of 54 TÜV SÜD AMERICA INC 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone: 858 678 1400 FAX: 858 546 0364 SECTION 1 REPORT SUMMARY Radio Testing of the CalAmp Wireless Networks Corp. GPS Tracking Unit with OBD-I…

Text truncated - open the document above for the full version.

FCC ID: APV‐4230HBT IC: 5843C‐4230HBT Radiated Emissions Test Setup (below 1GHz) Radiated Emissions Test Setup (above 1GHz)

FCC ID APV-3030HBT IC: 5843C-3030HBT Radiated Emissions Test Setup (below 1GHz) Note: Project SC1406705 and SC1409996 uses identical test setup. EUT are also identical except for the cellular radio type installed. Radiated Emissions Test Setup (above 1GHz) Note: Project SC1406705 and SC1409996 uses identical test setup. EUT are also identical except for the cellular radio type installed. Radiated Emissions Test Setup Note: Project SC1406705 and SC1409996 uses identical test setup. EUT are also identical except for the cellular radio type installed.