AXYATX033MX-3 Radio Control System

M X - 3 M X - 3 M X - 3 M X - 3 M X - 3 MX-3 Get The Advantage 3 Channel Computer Radio System MODEL BATT REV ARC SUB-TMODEL EPAD/R TH H L LR ST B / DSC 1 2 3 Super Micro 3 CH. Receiver 92836 75 FM M hz #1#2#3 Steering Throttle AUX B/DSC Switch AA Dry Cell Battery Holder Mechanical Speed Controller B / DSC 1 2 3 Super Micro 3 CH. Receiver 92836 75 FM M hz #2 Electronic Speed Controller ESC TRANSMITTER BATTERY INSTALLATION RECEIVER AND SERVO CONNECTIONS Your MX-3 Computer R/C system receiver is NOT equipped with BEC circuitry. DO NOT use more than 6.0 volts to power the receiver. Anything higher than 6.0 volts will burn-up or destroy your receiver. Only use a 4.8~6.0 volt battery pack or a speed controller that is designed to lower the voltage to the receiver. The following diagram shows a typical connection for the servos and receiver. Note that the receiver antenna should be located at least 2” (50mm) away from any servo leads and switches. In electric cars, we recommend that it be at least 4” (100mm) from the electric motor. Extend the receiver antenna to the full length. Failure to do so will cause loss of control. Do not cut or bend the receiver antenna. Insulate the connectors with tape or use tie wraps to avoid contact with metal car chassis. Please follow the model manufactures recommendations for the correct installation of your radio system in your car or boat. Switch To Battery To Motor ! CAUTION When installing your MX-3 radio system in your model, always make sure to set your model on a stand so the wheels are free from any traction before turning on your radio and or connecting your motor for the first time. TRIGGER POSITION ADJUSTMENT Throttle Trigger Set Screw Throttle Trigger Position Gauge A B Throttle Trigger Adjustment screw NOTE: Trigger Set Screw must be loosened before adjusting The Throttle Trigger can be adjusted to give you a more natural feel of the throttle. To Adjust: 1. Loosen the Throttle Trigger set screw by turning counter clock-wise. 2. Turning the adjustment screw clock-wise will move the trigger out or in the (A) direction. 3. Turning the adjustment screw counter clock-wise will move the trigger in or towards the (B) direction. 4. After adjustment is made, re-tighten the Trigger Set Screw. 5. Total adjustment for the trigger is 10mm. Do Not over tighten adjustment screw, it may damage the adjuster and or the threads. TROUBLESHOOTING GUIDE and WARNINGS If your radio system does not operate properly, please check the following items: 1. Make sure the batteries are properly installed and fully charged. With alkaline batteries, make certain the batteries are installed in the correct direction. 2. Check that both the transmitter and receiver power switches are in the ON position. 3. Check the battery voltage by turning on the transmitter and pushing both menu bottons at the same time and releasing. 4. Make sure that the proper frequency crystals are installed in both the transmitter and receiver. 5. Make sure all the receiver and servo connections are tight. WARNINGS: DO NOT OPERATE YOUR SYSTEM IF SOMEONE ELSE IS ON YOUR FREQUENCE AT THE SAME TIME. YOUR MODEL CAN CAUSE SERIOUS DAMAGE OR INJURY SO PLEASE USE CAUTION AND COURTESY AT ALL TIMES. DO NOT EXPOSE THE RADIO SYSTEM TO WATER OR EXCESSIVE MOISTURE. PLEASE WATER PROOF THE RECEIVER AND SERVOS BY PLACING THEM IN A WATER TIGHT RADIO BOX WHEN OPERATING R/C BOAT MODELS. IF YOU HAVE LITTLE OR NO EXPERIENCE OPERATING R/C MODELS, WE STRONGLY RECOMMEND YOU SEEK THE ASSISTANCE OF EXPERIENCED MODELERS OR YOUR LOCAL HOBBY SHOP FOR GUIDANCE. To Open slide CoverInstall BatteriesTo Close slide cover Press down on the battery cover and slide in the direction of the arrow to remove. Install 8 pieces “AA” size alkaline batteries as indicated on the battery tray. Make sure to match the polarity (+ and -) as shown in the battery compartment or the transmitter will not function. Install the battery cover in place and slide to close. 1. 2. 3. WARNING: Improper installation of transmitter batteries can cause serious damage to your system. To Battery To Motor DIGITAL CONTROL SYSTEM + - INC / DEC MENU ESC REGISTRATION NUMBER The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. SYSTEM FEATURES MODEL BATT REV ARC SUB-TMODEL EPAD/R TH H L LR ST We appreciate your purchase of this new Airtronics MX-3 Radio Control System. These instructions are intended to familiarize you with the many unique features of this modern, state of the art equipment. Please read them carefully so you may obtain maximum success and enjoyment from its operation. Please note that the MX-3 is designed for comfort and precise control of all types of model cars and boats. We wish you the best of success with your radio system. Enjoy and have fun. MX-3 Unique and functional pistol grip transmitter design Well balanced for precise control Non-slip rubber steering wheel Well placed digital trim levers Optimum third channel switch location Big LCD display Adjustable (70/30) Throttle trigger Low Battery warning Quick access transmitter crystal High performance micro 3 channel receiver High torque / high speed 94102Z servo Receiver dry battery holder Switch harness NiCd charger jack in transmitter Wrist strap holder (optional wrist strap part # 99104 ) Sound Beep ( On / Off ) Digital Trim indicators (throttle and steering) Battery Fuel Tank Dual Rate Steering EPA Steering, Throttle, AUX ARC Steering, Throttle Model Memory (5) Sub-Trim Steering, Throttle Servo Rev Steering, Throttle, AUX Battery Voltage Display Audio On / Off Screen Display SYSTEM SPECIFICATIONS Model: Output power: Modulation: Power supply: Weight: Frequencies: MX-3 200 MW FM/PPM 8 AA alkaline dry cells DC 12V or 8 cell NiCd Pack. 14.46 ounces 27 MHz (6) frequencies 75 Mhz (30) frequencies Trans…

Text truncated - open the document above for the full version.

‘ì‰ ñ ̃ H ƒNƒƒ bƒ N ”-U‰ ñ ̃ H “dŒ ¹‰ ñ ̃ H @@‚ T‚ u •\¦‰ ñ ̃ H ƒŠƒ Zƒ bƒ g ‰ñ ̃ H ‹L‰ ̄‰ ñ ̃ H ‚q‚ e• ” DC BROCK DIAGRAM SPECIFICATION TX-RADICON 3/6 D ’ü” {‰ ñ ̃ H @@ @ I’ i‘• ‰ñ ̃ H @@ LOW PASS FI LTER @@ Tr:2SC2 757 Tr:2SC2 757 Tr:Q4 RF OUT(ANT) ’ ü” {” ‚p‚ S F ~‚ Q@ @@@ @ 2SC4735 F ~‚ R 2SC4910 ŠÉÕ‘• ‰ñ ̃ H F –³‚ μ@@@@@@@@@@@@@@@@@ @@2SC4735 SPECIFICATION TX-RADICON 4/6 •Ï’ ²‰ ñ ̃ H @@ ”-M‰ ñ ̃ H @@ ’ü” {‰ ñ ̃ H @@ @@~ ‚ Q D:SVC20 3CP Tr:2SC2 757 ‚c‚ b• ” RF BROCK DIAGRAM ü @ @311 A20242A F ~ @ @311A20244A F ~ 31 1A 2024 1A F ì‰ ñH @@‚ T‚ u

FCC ID Label/Location: FCC ID Label: FCC ID AXYATX033

Response to: Correspondence Reference Number: 23392 731 Confirmation Number: EA484985 FCC ID AXYATX033 Applicant: Airtronics Inc (1) The radio equipment Model MX-3 is a 3 Channel Frequency Modulated Radio Control transmitter. The operating frequency of the transmitter can be any one channel in the 75.41-75.99MHz Remote Control frequency band. There are no controls or levers accessible to the user that can change the operating frequency. The MX-3 is used for remote control of ground units such as model cars and boats. The operating power of the MX-3 is 12VDC from either 8 AA alkaline dry cells or an 8-cell NiCd Pack. (2) Refer to Exhibit - Updated FCC Report

PCB    XC6202P5 M 24LC01BT   ×            (TUBE)     (TUBE) (TUBE)          (TUBE)  ×   (TUBE) 

1 03 R104 R105 R108 C108 C109 VC1 C110 TC1 C111 R106 C113 R107 C112 R109 C114 C115 R110 R114 C122 R111 C118 R113 C119 C120 C116 R115 C127 R118 C128 C129 R119 R125 L101 C134 C135 R116 C124 R117 C125 C126 R120 C131 R123 R124 C132 C136 C123 C130 R121 C133 T2 T3 Q3 Q4 L1 02 L1 03 L1 04 C137 C138 T1 Q2 Q1 XTAL C104 C105 STB 7.0V EN D:R1 26 EN D:L1 04 EN D:C1 38 TP9 GND2 R112 JP124 R122 SPECIFICATION TX-RADICON 1/6 R103 C106 C107 C108 R1 02 VR101 R101 C117 C101 C104 IC1 01 MOD C103 DT1 01 DT 10 2 TP8 RF-CUT VDD GND 1 2 3 4 5 C102 ‚q‚ e• ” R126 TP10 SPECIFICATION TX-RADICON 2/6

A-011-02-C Page 1 of 22 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan Designated by Ministry of international Trade and industry KANSAI ELECTRONIC INDUSTRY DEVELOPMENT CENTER HEAD OFFICE IKOMA TESTING LABORATORY 6-8-7 NISHITENMA 12128 TAKAYAMA-CHO KITA-KU OSAKA 530-0047 JAPAN IKOMA-CITY NARA 630-0101 JAPAN Corporate Juridical Person TEST REPORT Report No.A-011-02-C Date: 26April 2002 This test report is to certify that the tested device properly complies with the requirements of: FCC Rules and Regulations Part 95 : Radio Control (R/C) Radio Service. The tests necessary to show compliance to the requirements were performed and these results met the specifications of requirement. The results of this report should not be construed to imply compliance of equipment other than that, which was tested. Unless the laboratory permission, this report should not be copied in part. 1. Applicant Company Name : SANWA ELECTRONIC INSTRUMENT CO., LTD. Mailing Address : 1-2-50, YOSHIDA, HONMACHI-CHO, HIGASHIOSAKA-CITY, OSAKA, 578-0982 JAPAN 2. Identification of Tested Device Type of Device : Radio Control (R/C) Radio Service. Kind of Equipment Authorization : : DoC : Certification : Verification FCC ID : AXYATX033 Device Name : RADIO CONTROL TRANSMITTER Trade Name : AIRTRONICS Model Number : MX-3 Serial Number : ES2-05 : Prototype : Pre-production : Production Date of Manufacture : April 2002 3. Test Items and Procedure : RF Power Output (Substitution Method) : Modulation Characteristics : Emission Bandwidth : Field Strength of Spurious Radiation : Frequency Stability Measurement Above all tests were performed under: FCC Part 2 Sec2.1046, Sec2..1047, Sec2.1049, Sec2.1053, Sec2.1055 and Sec2.1057. : without deviation, : with deviation(details are found inside of this report) 4. Date of Test Receipt of Test Sample : 11 April 2002 Test Completed on : 24 April 2002 Seiichi Izumi General Manager of Ikoma Testing Laboratory A-011-02-C Page 2 of 22 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan Table of Contents 1. GENERAL INFORMATION ........................................................................................................3 1.1 Product Description ................................................................................................................3 1.2 Description for Equipment Authorization .............................................................................3 1.3 Test Facility ............................................................................................................................3 2. TESTED SYSTEM .......................................................................................................................4 2.1 Test Mode ................................................................................................................................4 2.2 Block Diagram of EUT System ..............................................................................................4 2.3 List of EUT System.................................................................................................................5 2.4 List of Antenna .......................................................................................................................5 3. RF POWER OUTPUT ..................................................................................................................6 3.1 Reference Rule and Specification ...........................................................................................6 3.2 Test Configuration ..................................................................................................................6 3.3 Test Procedure ........................................................................................................................7 3.4 Test Results.............................................................................................................................8 4. MODULATION CHARACTERISTICS ........................................................................................9 4.1 Reference Rule and Specification ...........................................................................................9 4.2 Test Results.............................................................................................................................9 5. EMISSION BANDWIDTH......................................................................................................... 11 5.1 Reference Rule and Specification ......................................................................................... 11 5.2 Test Configuration ................................................................................................................ 11 5.3 Test Results...........................................................................................................................12 6. FIELD STRENGTH OF SPURIOUS RADIATION ..................................................................16 6.1 Reference Rule and Specification .........................................................................................16 6.2 Test Procedure ....................................................................................................................16 6.3 Test Configuration ................................................................................................................17 6.4 Photographs of EUT System Configuration ........................................................................18 6.5 Test Results...........................................................................................................................19 7. FREQUENCY STABILITY MEASUREMENT .........................................................................20 7.1 Reference Rule and Specification .........................................................................................20 7.2 Frequency vs Temperature Test ....................…

Text truncated - open the document above for the full version.

A-011-02-C Page 1 of 20 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan Designated by Ministry of international Trade and industry KANSAI ELECTRONIC INDUSTRY DEVELOPMENT CENTER HEAD OFFICE IKOMA TESTING LABORATORY 6-8-7 NISHITENMA 12128 TAKAYAMA-CHO KITA-KU OSAKA 530-0047 JAPAN IKOMA-CITY NARA 630-0101 JAPAN Corporate Juridical Person TEST REPORT Report No.A-011-02-C Date: 23 July 2002 This test report is to certify that the tested device properly complies with the requirements of: FCC Rules and Regulations Part 95 : Radio Control (R/C) Radio Service. The tests necessary to show compliance to the requirements were performed and these results met the specifications of requirement. The results of this report should not be construed to imply compliance of equipment other than that, which was tested. Unless the laboratory permission, this report should not be copied in part. 1. Applicant Company Name : SANWA ELECTRONIC INSTRUMENT CO., LTD. Mailing Address : 1-2-50, YOSHIDA, HONMACHI-CHO, HIGASHIOSAKA-CITY, OSAKA, 578-0982 JAPAN 2. Identification of Tested Device Type of Device : Radio Control (R/C) Radio Service. Kind of Equipment Authorization : : DoC : Certification : Verification FCC ID : AXYATX033 Device Name : RADIO CONTROL TRANSMITTER Trade Name : AIRTRONICS Model Number : MX-3 Serial Number : ES2-05 : Prototype : Pre-production : Production Date of Manufacture : April 2002 3. Test Items and Procedure : RF Power Output (Substitution Method) : Modulation Characteristics : Necessary Bandwidth : Emission Bandwidth : Field Strength of Spurious Radiation : Frequency Stability Measurement Above all tests were performed under: FCC Part 2 Sec2.1046, Sec2..1047, Sec2.1049, Sec2.1053, Sec2.1055 and Sec2.1057. : without deviation, : with deviation(details are found inside of this report) 4. Date of Test Receipt of Test Sample : 11 April 2002 Test Completed on : 22 July 2002 Seiichi Izumi General Manager of Ikoma Testing Laboratory A-011-02-C Page 2 of 20 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan Table of Contents 1. GENERAL INFORMATION.................................................................................................... 3 1.1. Product Description.............................................................................................................3 1.2. Description for Equipment Authorization ..........................................................................3 1.3. Test Facility .........................................................................................................................3 2. TESTED SYSTEM...................................................................................................................4 2.1. Test Mode.............................................................................................................................4 2.2. Block Diagram of EUT System ...........................................................................................4 2.3. List of EUT System .............................................................................................................5 2.4. List of Antenna ....................................................................................................................5 3. RF OUTPUT POWER AND RADIATED SPURIOUS EMISSIONS ....................................... 6 3.1. Reference Rule and Specification .......................................................................................6 3.2. Test Configuration...............................................................................................................6 3.3. Test Configuration...............................................................................................................7 3.4. Photographs of EUT System Configuration .......................................................................9 3.5. Test Results .......................................................................................................................10 4. MODULATION CHARACTERISTICS...................................................................................11 4.1. Reference Rule and Specification ..................................................................................... 11 4.2. Test Results ....................................................................................................................... 11 5. EMISSION BANDWIDTH .................................................................................................... 13 5.1. Reference Rule and Specification .....................................................................................13 5.2. Test Configuration.............................................................................................................13 5.3. Test Results .......................................................................................................................14 6. FREQUENCY STABILITY MEASUREMENT ..................................................................... 18 6.1. Reference Rule and Specification .....................................................................................18 6.2. Frequency vs Temperature Test........................................................................................18 6.3. Frequency vs Voltage Test.................................................................................................19 7. USED TEST EQUIPMENTS AND CALIBRATION STATUS .............................................. 20 A-011-02-C Page 3 of 20 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan 1. GENERAL INFORMATION 1.1. Product Description The AIRTRONICS Model No. MX-3 (referred to as EUT in this report) is the RADIO CONTROL TRANSMITTER. (1) Transmitting Frequency : 75.41 ∼ 75.99 MHz (75.73 MHz in EUT) (2) Contained Oscillator : 6th OVER-TONE (3) Rated Power Supply : DC 12.0 V (AA type battery × 8) 1.2. Description for Equipment Aut…

Text truncated - open the document above for the full version.