BGB485Time Lapse VCR

40-hour Continuous Recorder Instruction Manual Technical Support is available from 8 a.m - 6 p.m CST by calling 800-444-6278 (inside the U.S.) or 972-353-6857 (outside the U.S.). SR40CTCN-A WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. La fléche symbolisant l’éclair dans un triangle équilateral a pour objet de tirer l’attention de l’utilisateur sur le fait, qu’il y a des “tensions dangereuses” non-isolées à l’intérieur de l’enceinte du produit qui peuvent être suffisamment impor-tantes pour conduire au risque d’électrocution. Le point d’exclamation au sein d’un triangle équilateral a pour objet de tirer l’attention de l’utilisateur sur le fait qu’il y a des instructions de mise en service et d’entretien (de réparation) dans les fiches descriptives de l’apprareil qui doivent obligatoirement être respectées. AVERTISSEMENT: AFIN D’ÉVITER TOUT RISQUE D’INCENDIE OU D’ÉLECTROCUTION, NE PAS EXPOSER CET APPAREIL À LA PLUIE NI À L’HUMIDITÉ. ATTENTION: POUR PRÉVENIR LES CHOCS ÉLECTRIQUES NE PAS UTILISER CETTE FICHE POLARISÉE AVEC UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ÊTRE INSÉRÉES À FOND SANS EN LAISSER AUCUNE PARTIE À DÉCOUVERT. AVERTISSEMENT DANGER D’ÉLECTROCUTION NE PAS OUVRIR AVERTISSEMENT: POUR ÉLIMINER TOUT RISQUE D’ÉLECTRO-CUTION, NE PAS OUVRIR LE COUVERCLE (OU LA PARTIE ARRIÈRE). AUCUNE PIECE RÉPARABLE PAR L’UTILISATEUR NE SE TROUVE À L’INTÉRIEUR. POUR TOUTE INTERVENTION D’ENTRETIEN OU DE RÉPARATION SE CONFIER AUX TECHNICIENS QUALIFIÉS. ii Please read all these instructions carefully regarding your VCR before you begin operating it. Follow all warnings and instructions marked on the VCR. 1 Read Instructions All the safety and operating instructions should be read before the product is operated. 2 Retain Instructions The safety and operating instructions should be retained for future reference. 3 Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 4 Follow Instructions All operating and use instructions should be followed. 5 Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7 Water and Moisture Do not use this product near water — for example, near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and the like. 8 Accessories Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manu- facturer. 9A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 11 Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to op- erate from battery power, or other sources, refer to the operat- ing instructions. 12 Grounding or Polarization This video product is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13 Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, conven- ience receptacles, and the point where they exit from the prod- uct. 14 Lightning For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 15 Overloading Do not overload wall outlets, extension cords, or integral con- venience receptacles as this can result in fire risk or electric shock. 16 Object and Liquid Entry Never push objects of any kind into this product through open- ings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 17 Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 18 Damage Requiring Service Unplug this product from the wall out…

Text truncated - open the document above for the full version.

A-023-02-A Block Diagram of EUT System VIDEOIN AUDIOIN VIDEOOUT AUDIOOUT ACIN RS485IN RS485OUT RS232RS485 ALMIN ALMOUT RSTIN RECIN GND MODEOUT CLKOUT FDDI/O UNIT Personal Computer RS232C/RS485 CONVERTER RS485IN CONTINUOUS VIDEO CASSETTE RECORDER ColorPrinter ACAdaptor CALLOUT ACAdaptor toAC120V,60Hz COLORCCD Camera(I) Color Television Receiver VIDEOOUT MIC VIDEOIN1 AUDIOIN1 ACAdaptor CONTINUOUS VIDEO CASSETTE RECORDER (A) [EUT] One End Open (B) (C) (D) (E) (F) (G) (H) (J) (K) toAC100V,60Hz toAC120V,60Hz toAC120V,60Hz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 :FerriteCore :SignalLine :PowerLine

776C223A4 E152293 MAGNETOSCOPE CONTINU DE CASSETTE VIDEO CONTINUOUS VIDEO CASSETTE RECORDER MODEL / MODELE AC100-230V50/60Hz18W SR40CTCN-A PAR MITSUBISHI DISTRIBUTED BY / DISTRIBUE PAR Ultrak 1301 Waters Ridge Drive, Lewisville, TX 75057 (800)796-2288 · (972)353-6400 MADE IN MALAYSIA BY / FABRIQUE EN MALAISIE FCC ID:BGB485 SR40CTCNA

Location of notes Side Notes

1/ RS-485 Interface The protocol is included in the installation manual. The interface is a standard of RS-485. TIME LAPSE VIDEO CASSETTE RECORDER PRODUCT SPECIFICATION Model Name : SR40CTCN-A MITSUBISHI ELECTRIC CORPORATION KYOTO WORKS 2/ 1. SPECIFICATION 1.1 Tape format : VHS 1/2" width high-density video cassette tape. 1.2 Input voltage range : AC100-230V 50/60Hz. 1.3 Power consumption : Approx. 18 Watts. 1.4 Television system : 525 lines, 60 fields NTSC-type color system. 1.5 Video recording system : 2 rotary heads, azimuth helical scanning system. 1.6 Luminance signal : Frequency modulation recording. 1.7 Color signal:Low frequency conversion, sub-carrier phase-shift recording. 1.8 Audio track : 1 track 1.9 Tape speed and recording time : (with T-160 cassette) Mode Time Speed Recording interval Number of Fields Drive (2H)(2.6 hrs)(33.35mm/sec)(16.68ms/Field)(60 Fields/sec)(Continuous) 8H8 hrs11.12mm/sec16.68ms/Field60 Fields/secContinuous L24H24 hrs3.71mm/sec50.04ms/Field20 Fields/secTime lapse L40H40 hrs2.22mm/sec83.40ms/Field12 Fields/secTime lapse ( ) is for Playback only. 1.10 Fast forward/Rewinding time : Approx. 90sec. with T-120 cassette. 1.11 Heads (1) Video : 4 rotary heads. (2) Audio/Control : 1 stationary head. (3) Erase : 1 full-track head. 1.12 Motors : 3 motors-(drum/capstan/loading) direct drive. 1.13 Video input : 1.0V(p-p),75ohm unbalanced BNC plug. 1.14 Audio input : 308mV(rms),50Kohm unbalanced RCA plug. 1.15 Video output : 1.0V(p-p),75ohm unbalanced BNC plug. 1.16 Audio output : 388mV(rms),1Kohm unbalanced RCA plug. 1.17 Audio frequency response : 70Hz4000Hz(8H Mode). 1.18 Signal to Noise Ratio (1) Video : better than 42 dB (8H Mode). (2) Audio : better than 43 dB (8H Mode). 1.19 Horizontal Resolution (1) Black & White : More than 330 lines. (2) Color : More than 240 lines. 3/ 1.20 Alarm Recording Time (1) Timed : 15sec /30sec /45sec /1min. /2min. /5min. /10min. (2) Manual : MAN1 Until the alarm reset switch is switched on. MAN2 Until the alarm in switch is switched off. 1.21 Display format : (Month)-(Day)-(Year) (Day of week) (Hour):(Minute):(Second) (Recording mode) or (Month)-(Day)-(Year) (Hour):(Minute):(Second). 1.22 Display position : In any position. 1.23 Timer program : 8 programs-Daily start and stop time for one week. 1.24 Battery Backup : Last for more than 31 days (when full charged). 1.25 Elapsed Time Indicator: The maximum of 89,999 hours. 4/ 2. CONNECTORS 2.1 ALM Input : Screw terminal for starting alarm recording. ACTIVE; When terminals are short-circuited or "L" level. 2.2 RST Input: Screw terminal for finishing alarm recording or for adjusting on-screen clock. ACTIVE; When terminals are short-circuited or "L" level. 2.3 REC Input : Screw terminal for starting/finishing recording or series recording. ACTIVE; When terminals are short-circuited or "L" level. 2.4 GND : Screw terminal for ground. 2.5 ALM output : Screw terminal for output while alarm recording is under way. ACTIVE; "L" Level, max. Current 50mA (+5VDC)/10mA(+24VDC) NON ACTIVE; OPEN, max. Voltage +24V DC. 2.6 MODE output : Screw terminal for indication of VCR selected mode. ACTIVE; "L" Level, max. Current 50mA (+5VDC)/10mA(+24VDC) NON ACTIVE; OPEN, max. Voltage +24V DC. 2.7 CLK output: Screw terminal to command camera switching. A pulse of the frequency division ratio selected by on-screen menu. 2.8 CALL output : Screw terminal for external warning device or series recording. ACTIVE; "L" Level, max. Current 50mA (+5VDC)/10mA(+24VDC) NON ACTIVE; OPEN, max. Voltage +24V DC. 5/ 3. NET SPECIFICATION 3.1 NET Dimension 425(W) 314(D) 95(H) mm Figure 4.1 3.2 Weight 4.2 kg 4. ACCESSORIES 1) Operation manual 1 pc. (Language English, Spanish) 2) AC-Power-Cord1 pc. 3) VCR Cable 1 pc. 4) BNC-RCA Adapter2 pcs. 5) Product Guide1 pc. 6) Warranty Card1 pc. 5. ENVIRONMENTAL CONDITION 5.1 Transport condition (Regular packing) 1) Truck (Container on flat car):Less than 2000km 2) Railroad (Container on flat car) :Less than 5000km 3) Ship (Container):Inside of hold 4) Freight:Forklift truck (Palletizers) Manual handling 5.3 Store condition (Regular packing) 1) Temp:20 , Humidity:60%RH Max. 1 year with specified stack number 2) Temp:40 , Humidity:90%RH Max. 250 hours with specified stack number 5.4 Usage condition 1) Temperature 5 °C 40 °C 2) Humidity Max.80% RH 6/ 3) Altitude Max.3000m Without dew 8.4 Vibration Drop condition 1) Vibration Random vibration PSD Wave form B 9.24 m/s 2 frequency band 5 100Hz vibration times 1 hour 2) Drop 1 corner, 2 edges, 5 faces (1 corner 40cm, 2 edges 40cm, Side, Front, Rear faces 40cm, Bottom face 50cm)

A-023-02-A Page 1 of 5 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan APPENDIX Photographs of EUT System Configuration Tested Item ・Conducted Emission measurement FRONT VIEW A-023-02-A Page 2 of 5 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan - Continued - LEFT SIDE VIEW A-023-02-A Page 3 of 5 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan - Continued - RIGHT SIDE VIEW A-023-02-A Page 4 of 5 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan Tested Item ・Radiated Emission measurement FRONT VIEW REAR VIEW A-023-02-A Page 5 of 5 KEC Ikoma Testing Laboratory 12128 Takayama-cho Ikoma-city Nara 630-0101 Japan - Continued - REAR VIEW