BOOKP-Y4073821Wireless Electric Pen

WIRELESS ELECTRIC PEN 1. Installation: Connect the USB RECEIVER and mini PC with supplied USB CABLE : male end is inserted into USB port of MINI PC and another end connected to USB RECEIVER, as shown below: MINI PC REAR VIEW OF WIHTEBOARD USB PORT EXTEND USB CABLE SUPPORTER FOR USB CABLE 2. Install battery as shown below 3. Write on electric whiteboard with pen tip and confirm by pressing pen tail RF2.4G USB RECEIVER W I R E L E S S E L E T R I C P C E N REARVIEW OF WHITEBOARD 4. Re-pair: in case of lost connection with USB RECEIVER or replace either of wireless electric pen or USB RECEIVER with new part, you need to do re-pair procedure as below: 1. Re-plug USB RECEIVER 2. Hold pen tail and pen tip for about 2 seconds, then release them 3. LED will flash 2 times slowly and it means both pen and USB RECEIVER pairs successfully 5. Specifications: .RF 2.4connection .Max wireless distance 10M .Power supply:DC 1.5V, alkaline battery 1pcs .Size: ø21*179mm .Weight: 30g 6. Package: .wireless electric pen 1 .user manual 1 .Alkaline battery 1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. CAN RSS-Gen/CNR-Gen. - English: This device complies with Industry Canada licence-exempt RSSs standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. - French:Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnem ent.

Unisen Limited FCC Confidentiality Request To the FCC and FCC TCB handling this application for certification Pursuant to 47 CFR Section 0.459(a) & (b), we, (the applicant / grantee) Company name Unisen Limited Addresss Room 907, Fook Hong Industrial Bldg.19 Sheung Yuet Road, Kowloon Bay, City Kowloon Country Hong Kong request non-disclosure and confidential treatment for our certification under: Grantee Code Product Number FCC ID: BOO KP-Y4073821 of the following materials submitted within this certification application: (please cross what is applicable, or add other documents) x Operational Description x Block Diagrams x Schematics Diagrams Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2) and 0.459. Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. We understand that pursuant to 47 CFR section 0.457(d)(1)(ii) and 0.459 disclosure of the applicant and all accompanying documentation will not be made before the date of the grant. Attestation: City and Country: Date: Name: (this must be a person) Function:Signature: (or official company stamp) Kowloon 2015/10/31 Yi Deng Engineer

Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ1021130 1 of 4 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. APPENDIX-A ATT-2015SZ1021130EUT Photo 1 Photo 2 Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ1021130 2 of 4 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 3 Photo 4

FCC ID LABELING AND LOCATION FCC ID Label Wireless Electric Pen Model NO.: Y4073821 FCC ID: BOOKP-Y4073821 FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ1021130 3 of 4 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 5 Photo 6 Shenzhen Asia Test Technology Co., Ltd. Reference No. - Page ATT-2015SZ1021130 4 of 4 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Photo 7 Photo 8 ANT

Shenzhen Asia Test Technology Co., Ltd. 7 / F, Xinwei Building, Gushu Village, Xixiang Town, Baoan District, Shenzhen, China Tel: +86)-0755-23284990 Email: [email protected] Http: // www.att-lab.cn This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Shenzhen Asia Test Technology Co.,Ltd. 7 / F, Xinwei Building, Gushu Village, Xixiang Town, Baoan District, Shenzhen, China Tel: +86)-0755-23284990 Fax: +(86)-0755-23284990 http:// www.att-lab.cn FCC RADIO TEST REPORT FCC ID: BOOKP-Y4073821 Product： Wireless Electric Pen Trade Name： iPazzPort Model Name： Y4073821 Serial Model： N/A Prepared for Unisen Limited Room 907, Fook Hong Industrial Bldg., 19 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong Prepared by Shenzhen Asia Test Technology Co.,Ltd. 7 / F, Xinwei Building, Gushu Village, Xixiang Town, Baoan District, Shenzhen, China Tel: +(86)-0755-23284990 Fax: +(86)-0755-23284990 Http: www.att-lab.cn Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ1021130F 2 of 48 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. TEST RESULT CERTIFICATION Manufacture's Name ........ Unisen Limited Address ............................. Wuwu Rd. Banshi Wuwu Village, Changping Town, Dongguan City Guangdong Prov. China Product description Product name ......................Wireless Electric Pen Model and/or type reference .......................... Y4073821 Additional Model ................ N/A Standards ......................... FCC Part15.247 Test procedure ..................... ANSI C63.10-2013 This device described above has been tested by ATT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ATT, this document may be altered or revised by ATT, personal only, and shall be noted in the revision of the document. Date of Test ........................................ Date (s) of performance of tests ......... Oct. 19 2015 ~Oct. 31 2015 Date of Issue ....................................... Oct. 31 2015 Test Result ........................................... Pass Testing Engineer : (Jack Yu) Technical Manager : (Jerry You) Authorized Signatory : (Can Liu) Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ1021130F 3 of 48 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Table of Contents Page 1 . SUMMARY OF TEST RESULTS 6 1.1 TEST FACILITY 7 1.2 MEASUREMENT UNCERTAINTY 7 2 . GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF EUT 8 2.2 DESCRIPTION OF TEST MODES 10 2.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 11 2.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 2.5 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 12 2.6 EQUIPMENTS LIST FOR ALL TEST ITEMS 13 3 . EMC EMISSION TEST 14 3.1 CONDUCTED EMISSION MEASUREMENT 14 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 14 3.1.2 TEST PROCEDURE 15 3.1.3 DEVIATION FROM TEST STANDARD 15 3.1.4 TEST SETUP 15 3.1.5 EUT OPERATING CONDITIONS 15 3.1.6 TEST RESULTS 15 3.2 RADIATED EMISSION MEASUREMENT 16 3.2.1 RADIATED EMISSION LIMITS 16 3.2.2 TEST PROCEDURE 17 3.2.3 DEVIATION FROM TEST STANDARD 17 3.2.4 TEST SETUP 18 3.2.5 EUT OPERATING CONDITIONS 19 3.2.6 TEST RESULTS (BELOW 30 MHZ) 20 3.2.7 TEST RESULTS (BETWEEN 30M – 1000 MHZ) 21 4 . NUMBER OF HOPPING CHANNEL 29 4.1 APPLIED PROCEDURES / LIMIT 29 4.1.1 TEST PROCEDURE 29 4.1.2 DEVIATION FROM STANDARD 29 Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ1021130F 4 of 48 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Table of Contents Page 4.1.3 TEST SETUP 29 4.1.4 EUT OPERATION CONDITIONS 29 4.1.5 TEST RESULTS 30 5 . AVERAGE TIME OF OCCUPANCY 31 5.1 APPLIED PROCEDURES / LIMIT 31 5.1.1 TEST PROCEDURE 31 5.1.2 DEVIATION FROM STANDARD 31 5.1.3 TEST SETUP 32 5.1.4 EUT OPERATION CONDITIONS 32 5.1.5 TEST RESULTS 33 6 . HOPPING CHANNEL SEPARATION MEASUREMENT 34 6.1 APPLIED PROCEDURES / LIMIT 34 6.1.1 TEST PROCEDURE 34 6.1.2 DEVIATION FROM STANDARD 34 6.1.3 TEST SETUP 34 6.1.4 EUT OPERATION CONDITIONS 34 6.1.5 TEST RESULTS 35 7 . BANDWIDTH TEST 37 7.1 APPLIED PROCEDURES / LIMIT 37 7.1.1 TEST PROCEDURE 37 7.1.2 DEVIATION FROM STANDARD 37 7.1.3 TEST SETUP 37 7.1.4 EUT OPERATION CONDITIONS 37 7.1.5 TEST RESULTS 38 8 . PEAK OUTPUT POWER TEST 40 8.1 APPLIED PROCEDURES / LIMIT 40 8.1.1 TEST PROCEDURE 40 8.1.2 DEVIATION FROM STANDARD 40 8.1.3 TEST SETUP 40 8.1.4 EUT OPERATION CONDITIONS 40 8.1.5 TEST RESULTS 41 9 . 100 KHZ BANDWIDTH OF F…

Text truncated - open the document above for the full version.

Shenzhen Asia Test Technology Co., Ltd. Report No. - Page ATT-2015SZ1021130F 48 of 48 - This document cannot be reproduced except in full, without prior written approval of ATT. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 11. EUT TEST PHOTO Radiated Measurement Photos Between 30MHz-1GHz Above 1GHz