C9O-HMIMB1Bridge Display

95-3018-022-000 Rev B 1 © 2019 SRAM, LLC Electronic Regulatory Compliance Manual 2 Electronic Regulatory Compliance Manual 3 Konformitätserklärung für elektronische Geräte 4 Manual de cumplimiento de la normativa electrónica 5 Manuel sur le respect des règlements concernant l'électronique 6 Manuale di Conformità Normativa Elettronica 7 Handleiding over de regelnaleving voor elektronische apparatuur 8 Manual de Conformidade com os Regulamentos de Electrónica 9 電子関連規制コンプライアンス・マニュアル 10 电子监管合规手册 11 Elektroniczny podręcznik zgodności z przepisami 12 Vedledning vedr. overholdelse af regulativer for elektronik 13 Příručka shody se zákonnými nařízeními pro elektroniku 14 Manual de conformare reglementări echipamente electronicei 15 Εγχειρίδιο ρυθμιστικής συμμόρφωσης σχετικά με τα ηλεκτρονικά 16 전자규정 준수를 위한 안내 17 電子監管合規手冊 18 Руководство по соответствию нормативным требованиям электронного устройства 2 Complies with ID A Standards D A107248 HIDF16000136 HIDF16000136 Electronic Regulatory Compliance Manual SRAM LLC certifies that this product and its packaging are in compliance with: RE Directive, the Radio Equipment Directive 2014/53/EC WEEE Directive, the Waste Electrical and Electronic Equipment Directive 2012/19/EU RoHS Directive, the restriction of the use of certain hazardous substances in electrical and electronic equipment 2002/95/EC REACh Directive, the Regulation on Registration, Evaluation, Authorization and Restriction of Chemical Directive 1907/2006/EC Batteries and Accumulators and Waste Batteries and Accumulators Directive 2006/66/EU This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada’s license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term “IC”: before the radio certification number only signifies that Industry Canada technical specifications were met. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L 'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RF Radiation Exposure Statement: Models 00010, 00110, 00210, 12810, 12910, 13200, 00220, 12920, 00030, 00130, 00020, 00120, 13000, 13100, 00500, 00601, 00610, 65501, 00230, 09601, 12930, 13400, 00021, and 00121 have been tested and complies with IC RSS 102 RF radiation exposure limits set forth for an uncontrolled environment when used with SRAM accessories supplied or designated for this product. To satisfy IC exposure requirements, a separation distance of at least 1.5 cm must be maintained between the antenna of this device and persons during device operation. The use of any other accessories may not ensure compliance with IC RSS 102 RF exposure guidelines. Declaration d'exposition aux radiations: Les modèles 00010, 00110, 00210, 12810, 12910, 13200, 00220, 12920, 00030, 00130, 00020, 00120, 13000, 13100, 00500, 00601, 00610, 65501, 00230, 09601, 12930, 13400, 00021, et 00121 ont été testés conformemment aux normes d'exposition d'emission RF de la IC RSS 102 pour un environement non controle lors d'utilisation avec les accessoires fournis or recommendes par SRAM. Pour satisfaire aux exigences d'exposition IC, une distance de separation d'au moins 1.5 cm doit etre maintenue entre l'antenne de cet appareil et des personnes pendant le fonctionnement de l'appareil. L'utilisation d'accessoires autres que ceux recommendes par SRAM ne guarantis pas la compatibilite avec les normes d'emission RF de la IC RSS 102. Warning: Any changes or modifications not expressively approved by SRAM could void the user's authority to operate this equipment. This product is ANT+ certified and complies with the bicycle power ANT+ Device Profile. For a complete listing of ANT+ Certified Products and their specific interoperability, please visit www.thisisant.com. 3 Complies with ID A Standards D A107248 HIDF16000136 HIDF16000136 Electronic Regulatory Compliance Manual Model #FCC IDIC TRA Dealer No: DA51171/16 ISRAEL מספר אישור אלחוטי של משרד התקשורת אסור להחליף את האנטנה המקורית של המכשיר ולא לעשות בו כל שינוי טכני אחר Left Shifter00010C9O-LSBB110161A-LSBB1 ER64861/1851-75254 Right Shifter00110 C9O-RSBB110161A-RSBB1 ER64862/1851-75255 BlipBox00210C9O-BOXB110161A-BOXB1 ER64863/1851-75256 Front Derailleur12810C9O-FDB110161A-FDB1 ER64864/1851-75257 Rear Derailleur1…

Text truncated - open the document above for the full version.

3 4 Battery ChargingCharge de la batterie Carregar a Bateria Laden der Batterie Carica della batteria 電池の充電 Recarga de la batería De batterij opladen 电池充电 1 2 Derailleur Battery InstallationInstallation de la batterie du dérailleurInstalação da bateria do derailleur (desviador) Einsetzen der Batterien für das SchaltwerkInstallazione della batteria del deragliatgore ディレイラーへの電池の取り付け Instalación de la batería del desviadorInstallatie van de derailleurbatterij 变速器电池安装 AB NOTICE Do not discard the derailleur battery block (A) or the battery cover (B). To prevent battery damage or depletion, install the derailleur battery block and battery cover whenever the battery is not installed. AVIS Ne jetez pas la cale de la batterie du dérailleur (A) ni la protection de la batterie (B). Afin d'éviter tout dommage ou déchargement involontaire de la batterie, mettez en place la cale de la batterie du dérailleur ainsi que la protection de la batterie à chaque fois que la batterie a été retirée. NOTIFICAÇÃO Não descarte o bloco da bateria do derailleur/desviador (A) nem a tampa da bateria (B). Para evitar a descarga da bateria ou danos a ela, instale o bloco da bateria do derailleur e a tampa da bateria sempre que a bateria não esteja instalada. HINWEIS Bewahren Sie den Batterietrenner (A) und die Batterieabdeckung (B) für das Schaltwerk auf. Um ein Entladen oder Beschädigungen der Batterie zu vermeiden, bringen Sie den Batterietrenner und die Batterieabdeckung für das Schaltwerk an, wenn die Batterie nicht eingesetzt ist. AVVISO Non gettare via li blocco batteria deragliatore (A) o il coperchio della batteria (B). Per evitare danni o esaurimento della batteria, installare il blocco della batteria del deragliatore e il coperchio della batteria quando la batteria non è installata. 注意事項 ディレイラーの電池ブロック(A)または電池カバー(B)を廃棄しない でください。電池の損傷と消耗を防ぐため、電池が取り付けられてい ないときは、常にディレイラーの電池ブロックと電池カバーを取り付 けてください。 AVISO No tire el bloque de batería del desviador (A) ni la tapa de batería (B). Para evitar que se dañe o se agote la batería, instale el bloque de batería del desviador y la tapa de batería siempre que la batería no esté instalada. MEDEDELING Gooi het derailleurbatterijblokje (A) of de derailleurbatterijkap (B) niet weg. Om schade of het onnodig ontladen van de batterij te voorkomen, installeer het derailleurbatterijblokje en de derailleurbatterijkap telkens de batterij niet is geïnstalleerd. 注意 不要丢弃变速器电池块 (A) 或电池防护罩 (B)。为避免电池损坏或耗 竭，每当电池不予以安装时，请安装变速器电池块和电池防护罩。 It may take up to one hour to reach a full charge. The amber LED indicates the battery is charging, and the green LED indicates the battery is charged. La charge complète de la batterie peut prendre jusqu’à une heure. La DEL orangée s’allume lorsque la batterie est en train de se charger et la DEL verte s’allume lorsque la batterie est chargée. Para alcançar a carga total poderá durar até uma hora. O LED de cor âmbar indica que a bateria está a carregar e o LED verde indica que a bateria está carregada. Es kann bis zu einer Stunde dauern, bis die Batterie vollständig geladen ist. Die gelbe LED zeigt an, dass die Batterie geladen wird. Die grüne LED zeigt an, dass die Batterie vollständig aufgeladen ist. Potrebbe essere necessaria fino a un'ora per raggiungere una carica completa. Il LED giallo indica che la batteria è in carica e il LED verde indica che la batteria è carica. 電池がフルに充電されるまで、最長で1時間ほどかかります。黄 色のLEDの点灯は電池が充電中であることを示し、緑色のLED の点灯は電池の充電が完了したことを示します。 La batería puede tardar hasta una hora en recargarse completamente. El LED ámbar indica que la batería se está cargando, y el verde que está ya cargada. Het kan tot één uur duren voordat de batterij volledig is opgeladen. De amberkleurige LED geeft aan dat de batterij aan het opladen is en de groene LED geeft aan dat de batterij opgeladen is. 电池完全充满可能需要一个小时。橙黄色LED表示电池正充 电，绿色LED表示充电已完成。 Remove Protective CoversRetirer les protections Retire as tampas protectoras Entfernen der SchutzabdeckungenRimuovere le coperture di protezione 保護カバーの取り外し Retire las tapas protectoras De beschermkappen verwijderen 拆下防护罩 SRAM AXS AppApplication SRAM AXSApp SRAM AXS SRAM AXS App App SRAM AXS SRAM AXS アプリ Aplicación SRAM AXSSRAM AXS app SRAM AXS App When installed correctly, the latch will snap into place.Si l’installation est correcte, le loquet s’emboîtera avec un petit déclic. Quando a instalação for feita correctamente, o trinco encaixará no seu lugar. Wenn die Batterie ordnungsgemäß eingesetzt ist, rastet die Verriegelung ein. Una volta installata correttamente, il fermo scatterà in posizione. 正しく取り付けると、ラッチが所定の場所にきちんと収ま ります。 Si se instala correctamente, el pestillo encajará en su posición.Bij een juiste installatie komt het slot op zijn plaats vast te zitten. 若安装正确，卡扣可以扣到位。 95-3018-029-000 Rev A© 2022 SRAM LLC Eagle AXS Transmission Quick Start Guide Eagle AXS-Antrieb Kurzanleitung Guía rápida de la transmisión Eagle AXS Guide de démarrage rapide pour transmission Eagle AXS Guida rapida alla trasmissione Eagle AXS Snelstartgids Eagle AXS- schakelgroep Guia de Início Rápido da Transmissão Eagle AXS Eagle AXS トランスミッシ ョン・クイックスタート・ ガイド Eagle AXS 传动系统快速 入门指南 Eagle AXS Transmission 1 2 12 Utilisez l'application SRAM AXS, disponible gratuitement dans les app stores, pour créer votre compte, ajouter vos composants et personnaliser votre expérience SRAM AXS. Pour les instructions complètes d'installation et d'utilisation, rendez-vous sur www.sram.com/service. Use a app AXS da SRAM, que está disponível gratuitamente nas lojas de apps, para criar a sua conta, acrescentar os seus componentes e personalizar a sua experiência AXS SRAM. Para instruções completas de instalação e utilização, visite www.sram.com/service. Nutzen Sie die in den App-Stores kostenlos erhältliche SRAM AXS App, um Ihr Konto zu erstellen, Ihre Komponenten hinzuzufügen und Ihr SRAM AXS-Benutzererlebnis anzupassen. Eine ausführliche Installations- und Bedienungsanleitung finden Sie auf www.sram.com/service. Utilizzare l'app SRAM AXS, disponibile gratuitamente negli app s…

Text truncated - open the document above for the full version.

Date: 1 1/16/2022 UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) fulfill the requirements for the scope of certification requested, including implementing any appropriate changes requested by UL Verification Services Telecommunications Certification Body (TCB) and / or the FCC; b) supply any and all information needed for the evaluation of the products for which certification is sought; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) not use our product certification in such a manner as to bring the TCB or FCC into disrepute and to not make any statement regarding product certification which the TCB or FCC may consider misleading or unauthorized; e) discontinue use of all advertising matter that contains any reference thereto and complies with any and all actions required by the FCC upon suspension or cancellation of certification; f) use certification only to indicate that products are certified in conformity with specified standards; g) endeavor to ensure that no certificate or report or any part thereof is used in a misleading manner, and any copies of the grants/certificates shall be reproduced in their entirety; h) comply with the requirements of the TCB and FCC, including the use of marks and label information prescribed for the scope of certification, when making reference to product certification in communication media such as documents, brochure or advertisements; i) comply with the requirements for certification, supply any information needed for evaluation of products to be certified and, where applicable, make provision for the participation of observers; j) ensure that products marketed under the scope of the requested certification continue to comply with the certification requirements; k) provide a sample of a production unit for testing within 30 days of the request should this product be selected as part of either the TCB’s or the FCC’s market surveillance requirements; l) keep a record of all complaints relating to product’s compliance with requirements of relevant standard; make records available to UL or FCC when requested; take appropriate action with respect to such complaints and any deficiencies found in the product that affect compliance with requirements for certification; document the actions taken with respect to complaints and/or deficiencies; m) inform the TCB immediately of any changes that may affect its ability to comply with the certification requirements. This authorization is valid until further written notice from the applicant. Sincerely Yours, Kyle Brenner Compliance Specialist SRAM, LLC [email protected]

Date: 11/14/2022 Attn: FCC Office of Engineering and Technology / UL Verification Services TCB Subject: Request for Confidentiality FCC ID: (C9O – HMIMB1) To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. • Schematic Diagram • Block Diagram • Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 05/01/2023: • External Photos • Internal Photos • Test Setup Photos • User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Kyle Brenner Compliance Specialist SRAM, LLC

Date: 11/4/2022 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Signatory Authorization FCC Grantee Code: C9O To whom it may concern: I, Leo Yermakov, the undersigned, hereby authorize Kyle Brenner to sign FCC related documents for SRAM. Sincerely Yours, Leo Yermakov Regulatory Compliance Director SRAM, LLC

A B C D E F G 12345678910 12345678910 A B C D E F G 100mm DRAWING NUMBERREVISION DRAWING NAME/DESCRIPTION CONFIDENTIAL - THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO SRAM CORPORATION AND MAY NOT BE DISCLOSED WITHOUT PERMISSION. FORMAT: A3SHEET: 1/1 ALL DIMENSIONS ARE mm UNSPECIFIED LENGTH TOLERANCE X.X +/- 0.5 DO NOT SCALE DRAWING UNSPECIFIED ANGLE TOLERANCE +/- 2degrees GEOMETRIC DIMENSIONING AND TOLERANCING TO BE INTERPRETED PER ASME Y 14.5-2009 DOCUMENT MAY NOT REPRESENT COMPLETE REQUIREMENTS. REFER TO PRODUCT STRUCTURE AJBERTAINITIAL REVISION 06DEC22 66.3018.150.010 GRAY = PANTONE 877C REVRESPONSIBLEREVISION RECORD DESCRIPTION PART NUMBER 66.3018.150.010 ARTWORK HMI LOWER HOUSING CERT ARTWORK HMI LOWER HOUSING CERT 66-3018-150-0XXA 14.9 equal equal CCAJ18LP31XXXX R-C-SRa-XXXXX TA-20XX/XXXX 007-AGXXXX C-XXXXX N30485 SUBTEL: XXXXX ANATEL 0XXXX-XX-XXXXX FCC ID: C9O-HMIMB1 IC: 10161A-HMIMB1 CCAJ18LP31XXXX R-C-SRa-XXXXX TA-20XX/XXXX 007-AGXXXX C-XXXXX N30485 SUBTEL: XXXXX ANATEL 0XXXX-XX-XXXXX FCC ID: C9O-HMIMB1 IC: 10161A-HMIMB1

Report No: RL/2021/90B Page 1 of 9 TEST REPORT Product Type: Company Name: Project: Report No: Issue Date: Prepared for: Test Engineer: Test Date: Cycle BT Controller on AL/CF frame SRAM GE Apollo RL/2021/90B August 12 .2021 Sven Baumann Andy Knowles (Radtenna Ltd) August 04/05/11 .2021 Test Engineer Signature: FIGURE 1 PRODUCT UUT Report No: RL/2021/90B Page 2 of 9 1.Test Description .................................................................................................................................... 3 2.Test Equipment ..................................................................................................................................... 3 3.Modification .......................................................................................................................................... 4 4.Conducted tests .................................................................................................................................... 5 4.1. Unit on Aluminum and Carbon Fiber frames .................................................................................... 5 5.Radiated Tests ....................................................................................................................................... 7 6.Radiated efficiency and peak gain ...................................................................................................... 19 7.Results observations ........................................................................................................................... 19 8.Appendix – Test configuration ............................................................................................................. 20 Report No: RL/2021/90B Page 3 of 9 1.Test Description Conducted and Radiated testing of SRAM Bluetooth Cycle Controller fitted to Aluminum and Carbon Fiber cycle frame material. For the Aluminum frame, the antenna was tested in both the open and blocked tube condition. Radiated testing used the products internal BTE IC to provide the RF test source. The conducted TX power was measured at -2dB at 2426 MHz 2.Test Equipment Conducted tests EquipmentManufacturerModelSerial NoCal Due Date VNA Anritsu MS46122A 1511303 26/07/2022 TABLE 1 CONDUCTED MEASUREMENT EQUIPMENT Radiated Tests EquipmentManufacturerModelSerial NoCal Due Date VNA Anritsu MS46122A 1511303 26/07/2022 Ref Antenna RF Echo OBH - 690 D20-4005901 19/10/2022 Positioner Dimond Engineering DAMS 6000 N/A N/A RF Chamber Radtenna SIDRAT 1.5 m x 2.5 m N/A N/A TABLE 2 RADIATED TEST SITE EQUIPMENT Report No: RL/2021/90B Page 4 of 9 3.Modification The supplied antenna was modified as shown in Figure 2 FIGURE 2 ANTENNA MODIFICATION 17mm 7 mm Report No: RL/2021/90B Page 5 of 9 FIGURE 3 MODIFIED UNIT 4.Conducted tests 4.1. Unit on Aluminum and Carbon Fiber frames FIGURE 4 MODIFIED SAMPLE UNIT, ON ALUMINUM FRAME Report No: RL/2021/90B Page 6 of 9 FIGURE 5 MODIFIED SAMPLE UNIT, ON CARBON FIBER FRAME Report No: RL/2021/90B Page 7 of 9 6.Radiated efficiency and peak gain Test Condition Peak Gain Efficiency 2402 MHz -2.6 dBi35% 2426 MHz -3.6 dBi33% 2480 MHz -5.5 dBi28% TABLE 3 ALUMINUM FRAME Test Condition Peak Gain Efficiency 2402 MHz -0.5 dBi36% 2426 MHz -0.7 dBi34% 2480 MHz -1.3 dBi29% TABLE 4 COVERED ALUMINUM FRAME Test Condition Peak Gain Efficiency 2402 MHz 0.3 dBi 38% 2426 MHz 0.3dBi 37% 2480 MHz -1.6 dBi30% TABLE 5 CARBON FIBER FRAME Note: Peak gain shown in tables above may not align with peak gain shown in 2D polar plots. This is because the peak may not have occurred in the 0° Elevation position and was therefore not captured in the Azimuth rotation @ 0° Elevation. 7.Results observations Modification of the antenna as detailed in section 3 increases the resonate frequency and brings it on center in the desired 2.4GHz BLE frequency band. Antenna radiation measurements show that the antenna is horizontally polarized and performs similarly on both Aluminum and Carbon Fiber frames, with a channel dependent efficiency of between 30% - 40%, which is in line with expectations. Report No: RL/2021/90B Page 8 of 9 8.Appendix – Test configuration FIGURE 18 CHAMBER TEST CONFIGURATION, ALUMINUM FRAME- SHOWN IN POSITION FOR 0 DEGREES EL, 0 DEGREES AZ FIGURE 19 CHAMBER TEST CONFIGURATION, COVERED ALUMINUM FRAME- SHOWN IN POSITION FOR 0 DEGREES EL, 0 DEGREES AZ Z X Y Report No: RL/2021/90B Page 9 of 9 FIGURE 20 CHAMBER TEST CONFIGURATION, CARBON FIBER FRAME -SHOWN IN POSITION FOR 0 DEGREES EL, 0 DEGREES AZ With reference to FIGURE 18, the green arrow shows the direction for rotation in the Elevation plane and the Red arrow shows the direction for rotation in the Azimuth plane.

TEST REPORT Report Number. : 14520556-E3V2 Applicant : SRAM LLC 1000 W Fulton Market 4 th Floor Chicago, IL 60607, United States Models : 13400 FCC ID : C9O-HMIMB1 ISED : 10161A-HMIMB1 EUT Description : Bridge Display Test Standard(s) : FCC 47 CFR PART 15 SUBPART C ISED RSS-210 ISSUE 10 ISED RSS-GEN ISSUE 5 + A1 + A2 Date of Issue: 2022-12-16 Prepared by: UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538 U.S.A. TEL: (510) 319-4000 FAX: (510) 661-0888 REPORT NO: 14520556-E3V2 DATE: 2022-12-16 FCC ID: C9O-HMIMB1 ISED: 10161A-HMIMB1 Page 2 of 40 UL VERIFICATION SERVICES INC. 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. REPORT REVISION HISTORY Rev. Issue Date Revisions Revised By V1 2022-12-01 Initial Issue --- V2 2022-12-16 Updated Section 6.3 and 9.3 Kiya Kedida REPORT NO: 14520556-E3V2 DATE: 2022-12-16 FCC ID: C9O-HMIMB1 ISED: 10161A-HMIMB1 Page 3 of 40 UL VERIFICATION SERVICES INC. 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. TABLE OF CONTENTS REPORT REVISION HISTORY .................................................................................................... 2 TABLE OF CONTENTS ............................................................................................................... 3 1. ATTESTATION OF TEST RESULTS .................................................................................... 5 2. TEST RESULTS SUMMARY ................................................................................................ 7 3. TEST METHODOLOGY ........................................................................................................ 8 4. FACILITIES AND ACCREDITATION .................................................................................... 8 5. DECISION RULES AND MEASUREMENT UNCERTAINTY ................................................ 9 5.1. METROLOGICAL TRACEABILITY ................................................................................ 9 5.2. DECISION RULES ......................................................................................................... 9 5.3. MEASUREMENT UNCERTAINTY ................................................................................. 9 5.4. SAMPLE CALCULATION ............................................................................................. 10 6. EQUIPMENT UNDER TEST ............................................................................................... 11 6.1. EUT DESCRIPTION ..................................................................................................... 11 6.2. MAXIMUM FUNDAMENTAL FIELD STRENGTH ........................................................ 11 6.3. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 11 6.4. SOFTWARE AND FIRMWARE .................................................................................... 11 6.5. WORST-CASE CONFIGURATION AND MODE .......................................................... 11 6.6. DESCRIPTION OF TEST SETUP ................................................................................ 12 7. MEASUREMENT METHOD ................................................................................................ 14 8. TEST AND MEASUREMENT EQUIPMENT ....................................................................... 15 9. ANTENNA PORT TEST RESULTS .................................................................................... 16 9.1. ON TIME AND DUTY CYCLE ...................................................................................... 16 9.2. 99% BANDWIDTH ........................................................................................................ 17 9.3. 20 dB BANDWIDTH ..................................................................................................... 18 10. RADIATED TEST RESULTS ........................................................................................... 20 10.1. ON TIME AND DUTY CYCLE ..................................... Error! Bookmark not defined. 10.2. LIMITS AND PROCEDURE ...................................................................................... 20 10.3. FUNDAMENTAL FREQUENCY RADIATED EMISSION .......................................... 22 10.4. TRANSMITTER ABOVE 1 GHz ................................................................................ 23 10.5. WORST CASE BELOW 30 MHz .............................................................................. 33 REPORT NO: 14520556-E3V2 DATE: 2022-12-16 FCC ID: C9O-HMIMB1 ISED: 10161A-HMIMB1 Page 4 of 40 UL VERIFICATION SERVICES INC. 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 10.6. WORST CASE BELOW 1 GHz ................................................................................. 34 10.7. WORST CASE 18-26 GHz ....................................................................................... 36 11. SETUP PHOTOS ............................................................................................................. 38 REPORT NO: 14520556-E3V2 DATE: 2022-12-16 FCC ID: C9O-HMIMB1 ISED: 10161A-HMIMB1 Page 5 of 40 UL VERIFICATION SERVICES INC. 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: SRAM LLC 1000 W Fulton Market 4 th Floor Chicago, IL 60607, United States EUT DESCRIPTION: Bridge Display MODELS: 13400 SERIAL NUMBER: Conducted: 1801721124 Radiated: 1801721117 DATE TESTED: 2022…

Text truncated - open the document above for the full version.

REPORT NO: 14520556-E3V2 DATE: 2022-12-16 FCC ID: C9O-HMIMB1 ISED: 10161A-HMIMB1 Page 38 of 40 UL VERIFICATION SERVICES INC. 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 11. SETUP PHOTOS ANTENNA PORT CONDUCTED SETUP RF ANTENNA PORT CONDUCTED REPORT NO: 14520556-E3V2 DATE: 2022-12-16 FCC ID: C9O-HMIMB1 ISED: 10161A-HMIMB1 Page 39 of 40 UL VERIFICATION SERVICES INC. 47173 Benicia Street, Fremont, CA 94538; USA TEL:(510) 319-4000 FAX:(510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. RADIATED RF MEASUREMENT SETUP BELOW 30MHz (FRONT) BELOW 30MHz (BACK) BELOW 1GHz (FRONT) BELOW 1GHz (BACK) ABOVE 1GHz (FRONT) ABOVE 1GHz (BACK) REPORT NO: 14520556-E3V2 DATE: 2022-12-16 FCC ID: C9O…

Text truncated - open the document above for the full version.