CH8A908260XXWireless Gateway

UltraLine II VDSL Gateway – Draft 1 030-300237 Rev. A 8/8/06 Copyright © 2006 Westell, Inc. 030-300237 Rev. A ULTRALINE II VDSL GATEWAY (MODEL 826010) USER GUIDE UltraLine II VDSL – Draft 1 030-300237 Rev. A 8/8/06 030-300237 Rev. A 2 August 2006 User Guide UltraLine II VDSL Gateway (Model 826010) TABLE OF CONTENTS 1. PRODUCT DESCRIPTION ..................................................................................................................................4 2. SAFETY INSTRUCTIONS ...................................................................................................................................4 3. REGULATORY INFORMATION ........................................................................................................................5 3.1 FCC Compliance Note ...............................................................................................................................5 3.2 Canada Certification Notice.......................................................................................................................6 4. NETWORKING REQUIREMENTS .....................................................................................................................7 5. HARDWARE FEATURES....................................................................................................................................8 5.1 LED Indicators...........................................................................................................................................8 5.2 Cable Connectors and Switch Locations....................................................................................................9 5.3 Connector Descriptions..............................................................................................................................9 6. INSTALLING THE HARDWARE......................................................................................................................10 6.1 Installation Requirements ........................................................................................................................10 6.2 Before you begin......................................................................................................................................10 6.3 Microfilters ..............................................................................................................................................10 6.4 Hardware Installations .............................................................................................................................11 6.4.1 Installation via Ethernet ...........................................................................................................................11 6.4.2 Connecting PCs via Wireless...................................................................................................................12 7. SETTING UP Macintosh OS X............................................................................................................................13 7.1 Opening the System Preference Screen ...................................................................................................13 7.2 Choosing the Network Preferences ..........................................................................................................13 7.3 Creating a New Location .........................................................................................................................14 7.4 Naming the New Location .......................................................................................................................14 7.5 Selecting the Ethernet Configuration .......................................................................................................15 7.6 Checking the IP Connection ....................................................................................................................15 7.7 Accessing the Gateway’s User Interface..................................................................................................16 8. CONFIGURING YOUR GATEWAY FOR INTERNET CONNECTION .........................................................17 8.1 Accessing your VDSL Gateway ..............................................................................................................17 8.2 Confirming Your VDSL Sync .................................................................................................................18 8.3 Setting Up Your Connection Profile ........................................................................................................19 8.4 Establishing a WAN Connection .............................................................................................................22 8.5 Disconnecting Your WAN Connection ...................................................................................................25 9. BASIC MODE .....................................................................................................................................................26 10. HOME ..................................................................................................................................................................27 10.1 Connection ...............................................................................................................................................27 10.2 Connection Summary...............................................................................................................................28 11. STATUS...............................................................................................................................................................29 11.1 About .......................................................................................................................................................29 11.2 LAN Devices ..................................................…

Text truncated - open the document above for the full version.

UltraLine II VDSL– Draft 1 030-300237 Rev. A 8/8/06 030-300237 Rev. A 51 August 2006 User Guide UltraLine II VDSL Gateway (Model 826010) 15.6.2 DNS The following screen will be displayed if you select Configuration > LAN > DNS from the menu options. The DNS screen allows you add static host names along with their IP addresses to your Gateway’s DNS server. DNS Domain Name Note: Some ISP’s may require the name for identification purposes. This field allows you to enter a Domain Name for the Gateway. To add a Domain Name, in the field under User Assigned DNS, type in your new domain name and click Set. Static Host Assignment Host Name This field allows you to enter a HOST name for the Gateway. To add a new Host name, in the field under Static Host Assignment, type in the Host Name and the associated IP address and then click Add. To delete a Host name, click the Delete button adjacent to the Host Name and IP Address you want to delete. IP Address Displays the IP address that is assigned to the Host Name. Discovered Local Devices This field displays a list of the computers on the LAN that have been assigned a DHCP Address. The DNS name and IP address entry of each discovered device is displayed. (Note: The values in this field will be displayed barring any propagation delays. If ‘No Discovered Devices’ is displayed, manually refresh the screen.) UltraLine II VDSL– Draft 1 030-300237 Rev. A 8/8/06 030-300237 Rev. A 52 August 2006 User Guide UltraLine II VDSL Gateway (Model 826010) To add a static host assignment, enter a Host Name and IP Address in the fields provided, and then click Add. After you have entered the desired values and clicked Add, the following screen will be displayed. If you want to delete a Static Host Assignment, click the adjacent Delete button of the Host Name/IP address you want to delete. UltraLine II VDSL– Draft 1 030-300237 Rev. A 8/8/06 030-300237 Rev. A 53 August 2006 User Guide UltraLine II VDSL Gateway (Model 826010) 15.6.3 Public LAN—Multiple IP Address Passthrough The following screen will be displayed if you select Configuration > LAN > Public LAN from the menu options. This screen contains the settings that control how the Gateway interacts with the local devices to which it is connected. NOTE: 1. Selecting Public LAN will enable your computer to have global address ability. To use the Public LAN feature, your ISP must support Public LAN and Static IP. Contact your ISP for details. 2. Westell recommends that you do not change these settings unless your service provider instructs you to do so. To enable Public LAN, do the following: 1. Click the Enable DHCP Server check box (a check mark will appear in the box). Note: By factory default this box will already contain a check mark. 2. Enter the appropriate address values in the fields provided. (Refer to the following table for information about the Private LAN settings.) 3. Enter the desired lease time values. 4. Click Save to save the settings. Alternate LAN - Public LAN Settings Select DHCP Network Displays the DHCP Network that you have selected. Enable DHCP Server Factory Default = Disable Possible Responses: If Enabled (box is checked), this will enable the Public LAN DHCP server and allow IP address to be server from the DHCP Public LAN pool. If Disabled (box is unchecked), this will disable the Public LAN DHCP server. UltraLine II VDSL– Draft 1 030-300237 Rev. A 8/8/06 030-300237 Rev. A 54 August 2006 User Guide UltraLine II VDSL Gateway (Model 826010) Modem’s Public IP Address The Gateway’s public IP address Subnet Mask The Subnet Mask, which determines what portion of an IP address is controlled by the network and which portion is controlled by the host. Address Range DHCP Start Address This value is provided by your Internet service provider and functions as the first IP address that the Public LAN DHCP Server will provide. The DHCP Start Address must be within the IP address and lower than the DHCP End Address. DHCP End Address This value is provided by your Internet service provider and functions the last IP address that the Public LAN DHCP Server will provide. The DHCP End Address must be within the IP address and higher than the DHCP Start Address. DHCP Lease Time Factory Default = 00:00:00:00 Displays the amount of time the provided addresses will be valid, after which time the Public LAN DHCP client will usually re-submit a request. Note: DHCP Lease Time is displayed in the format (day:hour:min:sec). This value must be greater than 10 seconds. (Hours must be between 0 and 23; Minutes must be between 0 and 59; and Seconds must be between 0 and 59.) If the settings you have entered in the Public LAN screen are incorrect, the following warnings messages may be displayed via pop-up screens. If this occurs, check the Public LAN settings. Warning Message Check Public LAN DHCP Settings Start Address is not part of the Subnet Check the value in the DHCP Start Address field End Address is not part of the Subnet Check the value in the DHCP End Address field End Address is below the Start Address Check the value in the DHCP End Address field Lease time must be greater than 10 seconds Check the values in the DHCP Lease Time fields Seconds must be between 0 and 59 Check the Seconds field at DHCP Lease Time Minutes must be between 0 and 59 Check the Minutes field at DHCP Lease Time Hours must be between 0 and 23 Check the Hours field at DHCP Lease Time UltraLine II VDSL– Draft 1 030-300237 Rev. A 8/8/06 030-300237 Rev. A 55 August 2006 User Guide UltraLine II VDSL Gateway (Model 826010) 15.6.4 IP Passthrough—Single IP Address Passthrough The following screen will be displayed if you select Configuration > LAN > IP Passthrough from the menu options. IP Passthrough enables you to select one device on your LAN that will share your WAN-assigned IP address. This configuration allows the device with the single static IP address to become visible on the Internet. Network Address Translation (NAT) and Firewall rules …

Text truncated - open the document above for the full version.

Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] External EUT Photographs FCC ID: CH8A908260XX Front of EUT Top of EUT Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] Rear of EUT Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] Bottom of EUT

Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] ID Label/Location The label is a polyester material with approximate size of 3” wide by 1” high with UL approved permanent adhesive. The label is located on the bottom center of the exterior of the product. Radiometrics Midwest Corporation (815) 293-0772 – [email protected] Bottom of EUT showing placement of label

Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] Internal EUT Photographs Photographs of WiFi Board: Front of WiFi Board Front of WiFi Board with shield removed Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] Rear of WiFi Board Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] Photographs of connections from the board to antennas Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] Photograph showing connection from WiFi board to antennas Photograph of Main Processor Board: Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] Photograph of EUT with cover removed

Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 – [email protected] RF exposure The 2.4 GHz transmitter Peak Power has a 28.5 dBm output with 2 dBi antenna gain The following information provides the minimum separation distance for the EUT, as calculated from FCC OET 65 Appendix B, Table 1B “Guidelines for General Population/Uncontrolled Exposure” This calculation is based on the highest EIRP possible from the EUT considering maximum power and antenna gain. The formulas were used: GP limit is = 1 mW/cm^2 above 1.5 GHz S= E^2/3770 mW/cm^2 E or V/m = (ERP*30)^0.5/d, (d in meters) d = ((ERP*30)/3770*S))^0.5 SPEAKAntennaMSD Freq.GP limitRF powerGainERPEd MHzmW/cm^2dBmdBiwattsV/mmeters 2462128.521.12261.40.094 GP is the limit for general Population/Uncontrolled Exposure MSD is the minimum Seperation Distance NOTE: For mobile or fixed location transmitters, minimum separation distance is 20 cm, even if calculations indicate MPE distance is less

Radiometrics Midwest Corporation (815) 293-0772 – www.radiomet.com Page 1 of 31 Electromagnetic Compatibility Test Report Tests Performed on a Westell, Inc. Ultraline IIv VDSL2 Gateway, Model A90-826010-07 Radiometrics Document RP-5839 Product Detail: FCC ID: CH8A908260XX Equipment type: 2.4 GHz Digitally Modulated Transmitter Test Standards: US CFR Title 47, Chapter I, FCC Part 15 Subpart C FCC Part 15 CFR Title 47: 2006 This report concerns: Original Grant for Certification FCC Part 15.247 Tests Performed For: Test Facility: Westell, Inc. 750 N. Commons Dr. Aurora, IL 60504 Phone: 630-898-2500 Radiometrics Midwest Corporation 12 East Devonwood Romeoville, IL 60446 Phone: (815) 293-0772 e-mail: [email protected] Test Date(s): (Month-Day-Year) May 25 and 26, 2006 Document RP-5839 Revisions: Rev. Issue Date Affected Pages Revised By 0 August 23, 2006 1 August 24, 2006 3, 30 Joseph Strzelecki RADIOMETRICS MIDWEST CORPORATION - EMC Test Report Testing of the Westell, Inc., Ultraline IIv VDSL2 Gateway, Model A90-826010-07 RP-5839 Rev. 1 Page 2 of 31 Table of Contents 1 ADMINISTRATIVE DATA........................................................................................................................3 2 TEST SUMMARY AND RESULTS.........................................................................................................3 3 EQUIPMENT UNDER TEST (EUT) DETAILS.......................................................................................4 3.1 EUT Description..............................................................................................................................4 3.1.1 FCC Section 15.203 Antenna Requirements...........................................................................4 3.2 Related Submittals..........................................................................................................................4 4 TESTED SYSTEM DETAILS.................................................................................................................4 4.1 Tested System Configuration..........................................................................................................4 4.2 Special Accessories........................................................................................................................5 4.3 Equipment Modifications..................................................................................................................5 5 TEST SPECIFICATIONS AND RELATED DOCUMENTS....................................................................5 6 RADIOMETRICS’ TEST FACILITIES.....................................................................................................5 7 DEVIATIONS AND EXCLUSIONS FROM THE TEST SPECIFICATIONS............................................6 8 CERTIFICATION....................................................................................................................................6 9 TEST EQUIPMENT TABLE...................................................................................................................6 10 TEST SECTIONS................................................................................................................................7 10.1 AC Conducted Emissions; Section 15.207...................................................................................7 Figure 1. Conducted Emissions Test Setup.....................................................................................9 10.2 Occupied Bandwidth (6 dB)..........................................................................................................9 10.3 Peak Output Power.....................................................................................................................13 10.4 Power Spectral Density...............................................................................................................14 10.5 Band-edge Compliance of RF Conducted Emissions................................................................14 10.6 Spurious RF Conducted Emissions............................................................................................17 10.7 Spurious Radiated Emissions (Restricted Band).......................................................................26 10.7.1 Radiated Emissions Field Strength Sample Calculation......................................................27 Figure 2. Drawing of Radiated Emissions Setup............................................................................28 10.7.2 Spurious Radiated Emissions Test Results (Restricted Band)...........................................29 Notice: This report must not be reproduced (except in full) without the written approval of Radiometrics Midwest Corporation. RADIOMETRICS MIDWEST CORPORATION - EMC Test Report Testing of the Westell, Inc., Ultraline IIv VDSL2 Gateway, Model A90-826010-07 RP-5839 Rev. 1 Page 3 of 31 1 ADMINISTRATIVE DATA Equipment Under Test: A Westell, Inc., Ultraline IIv VDSL2 Gateway Model: A90-826010-07 Serial Number: None This will be referred to as the EUT in this Report Date EUT Received at Radiometrics: (Month-Day-Year) Test Date(s): (Month-Day-Year) May 25, 2006 May 25 and 26, 2006 Test Report Written By: Test Witnessed By: Joseph Strzelecki Senior EMC Engineer Guy Cerulli Westell, Inc. Radiometrics’ Personnel Responsible for Test: Test Report Approved By Joseph Strzelecki Senior EMC Engineer NARTE EMC-000877-NE Chris W. Carlson Director of Engineering NARTE EMC-000921-NE 2 TEST SUMMARY AND RESULTS The EUT (Equipment Under Test) is an Ultraline IIv VDSL2 Gateway, Model A90-826010-07, manufactured by Westell, Inc. The detailed test results are presented in a separate section. The following is a summary of the test results. This report pertains to the 802.11 section and the unintentional radiator section of the Ultraline IIv VDSL2 Gateway. The EUT has two antennas for diversity. The RF can be routed to only one of the antenna ports at a time. I…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Radiated Emission - Front View (30-1000 MHz) Radiated Emission - Rear View (30-1000 MHz) Radiated Emission - Front View (Above 1000 MHz) Radiated Emission - Rear View (Above 1000 MHz) Frequency Stability View