CNVCCII-4HCarry-Coder II with Power Amplifier

Broadcast Microwave Services, Inc. – 12367 Crosthwaite Circle – Poway, CA 92064 1 Phone: 800-669-9667, 1-858-391-3050 - Fax: 1-858-391-3049 Email: [email protected] Web: www.bms-inc.com 4 GHz CARRY-CODER II User Manual Manual Part Number 6051412900 Rev - Specifications are subject to change without prior notice. This document contains confidential information and is intended for customer use only. It cannot be duplicated without prior authorization from BMS. Broadcast Microwave Services, Inc. – 12367 Crosthwaite Circle – Poway, CA 92064 2 Phone: 800-669-9667, 1-858-391-3050 - Fax: 1-858-391-3049 Email: [email protected] Web: www.bms-inc.com Broadcast Microwave Services, Inc. – 12367 Crosthwaite Circle – Poway, CA 92064 3 Phone: 800-669-9667, 1-858-391-3050 - Fax: 1-858-391-3049 Email: [email protected] Web: www.bms-inc.com GLOSSARY 16QAM Quadrature Amplitude Modulation (16 states) 64QAM Quadrature Amplitude Modulation (64 states) ATSC Advanced Television Standard Committee COFDM Coded Orthogonal Frequency Division Multiplex CVBS Composite Video Baseband Signal DCE Data Communication Equipment DVB Digital Video Broadcasting DVB-T Digital Video Broadcasting for Terrestrial TV EMC Electro-Magnetic Compatibility EU European Union GOP Group Of Pictures MPEG Moving Pictures Engineering Group PIN Personal Identification Number PID Packet Identifier QPSK Quad Phase Shift Keying US United States of America LEGEND = Idea (Highlighted operator Information) = Warning (indicates a critical or hazardous point) Broadcast Microwave Services, Inc. – 12367 Crosthwaite Circle – Poway, CA 92064 4 Phone: 800-669-9667, 1-858-391-3050 - Fax: 1-858-391-3049 Email: [email protected] Web: www.bms-inc.com WARNING! ........................................................................................................................................................ 5 OVERVIEW ....................................................................................................................................................... 7 INSTALLATION................................................................................................................................................ 9 Mobile and Fixed Platforms............................................................................................................................ 9 Installation Procedure ................................................................................................................................... 10 Installing the Battery on the Carry-Coder II ................................................................................................. 10 Controlling the CARRY-CODER II Transmitter ......................................................................................... 11 Control Unit Features................................................................................................................................ 11 Transmitter Operating Configuration............................................................................................................ 11 CARRY-CODER II Transmitter <EXPERT> Operating Mode Configuration ........................................... 12 OPERATING INSTRUCTIONS ...................................................................................................................... 12 Start-Up Indications ...................................................................................................................................... 12 Operator Menu Summary.............................................................................................................................. 13 INPUT/OUTPUT CHARACTERISTICS......................................................................................................... 13 Composite Video (CVBS) ............................................................................................................................ 13 Component Video (YUV) ............................................................................................................................. 13 Analog Audio ................................................................................................................................................ 14 Data Input...................................................................................................................................................... 14 Remote Control Port ..................................................................................................................................... 14 RF Output...................................................................................................................................................... 15 Power Supply Input....................................................................................................................................... 15 WARRANTY AND RETURN TO FACTORY ............................................................................................... 16 LINEAR POWER AMPLIFIER (BPA-1CC-4)................................................................................................ 18 Application.................................................................................................................................................... 18 Specification: ................................................................................................................................................ 18 CONTACT INFORMATION ........................................................................................................................... 19 Broadcast Microwave Services, Inc. – 12367 Crosthwaite Circle – Poway, CA 92064 5 Phone: 800-669-9667, 1-858-391-3050 - Fax: 1-858-391-3049 Email: [email protected] Web: www.bms-inc.com WARNING! RF RADIATION EXPOSURE HAZARD This warning is provided by Broadcast Microwave Services (BMS) Inc. for safety purpose. The following information help to reduce the r…

Text truncated - open the document above for the full version.

(8014129650) (8014129650) (8014129650) (8014079020) (8014079020) (8014079020) (8014079020) On 4 GHz Carry-Coder II Unit On 4 GHz Power Amp Unit

(8014129650)

Broadcast Microwave Services Inc. 12367 Crosthwaite Circle, Poway, CA 92064-6817 Phone: 858-391-3050. Toll Free: 800-669-9667. Fax: 858-391-3049. Web: www.bms-inc.com 1 Broadcast Microwave Services Inc. Made In USA FCC ID : CNVCCII-4H Model No: CCII-4H Sample FCC ID Label 0.5" 2.5"

4 GHz Carry-Coder II Unit 8014129650 Digital Board Assembly 7214206010 Digital Board 7214206900 Power Supply 7214215000 Internal Amplifier 7214216000 RFU Board 7214217000 4 GHz Power Amplifier Unit 8014079020 PA Pre-Driver Board Assembly 7214147000 PA Driver Board Assembly 7214148000 PA Final Board Assembly 7214149000 PA DC Routing Board 7214150000 (Front View) Upper Lid Digital Board Assembly Power Supply Board Fans RF Output (Rear View) RFU Board Internal Amp Board RF Output Digital Board MPEG Encoder Front View Rear View Front View Rear View Front View Rear View Front View Rear View Front View Rear View

Pre-Driver Board RF Input DC Input/ On-off Control DC Out (optional fan) RF Output Driver Board Final (output) Board DC Routing Board Front View Rear View Front View Rear View Front View Rear View Front View Rear View

Broadcast Microwave Services Inc. 12367 Crosthwaite Circle, Poway, CA 92064-6817 Phone: 858-391-3050. Toll Free: 800-669-9667. Fax: 858-391-3049. Web: www.bms-inc.com 1 EQUIPMENT The 4 GHz Carry-Coder II (CCII) with Power Amp is a non-broadcast mobile transmitter for use in the frequency range of 4949 MHz to 4990 MHz. This product supports the following Emission Designators: FCC ID Modulation Emission Designators CNVCCII-4H Digital 6M0W7D 7M0W7D 8M0W7D Operation under FCC rule part: 90 APPLICATION The 4 GHz Carry-Coder II w/PA is designed for use in the Public Safety band and Law Enforcement Command Posts (rule part 90). The 4 GHz Carry-Coder II supports digital data transmission. The 4 GHz Carry-Coder II w/PA operates in digital (COFDM) transmission mode. It features a DVB-T compliant (COFDM) modulator MPEG2 video encoder. The system is designed to support either 6, or 7, or 8 MHz occupied bandwidth. The product includes the Carry-Coder II unit as well as a power amplifier unit with the maximum output power limited to 1W in compliance with the FCC rule part 90. TECHNICAL DESCRIPTION Technical description is detailed in the User’s Manual.

Broadcast Microwave Services Inc. 12367 Crosthwaite Circle, Poway, CA 92064-6817 Phone: 858-391-3050. Toll Free: 800-669-9667. Fax: 858-391-3049. Web: www.bms-inc.com 1 WARNING! RF RADIATION EXPOSURE HAZARD This warning is provided by Broadcast Microwave Services (BMS) Inc. for safety purpose. The following information help to reduce the risk of RF exposure hazard. FCC Limit of RF Exposure According to Federal Communication Commission (FCC), the Maximum Permissible Exposure (MPE) for FR radiation has been set to 1.0 mW/cm 2 for the 4 GHz Carry- Coder II with 1Watt Power Amp equipment (OET Bulletin 65). The 4 GHz Carry-Coder II with Power Amp is a non-broadcast transmitter and without an antenna it will not create RF exposure (power density) exceeding the 1.0 W/cm 2 FCC limit. However a high-gain antenna such as a parabolic dish will greatly enhance the 4 GHz Carry-Coder II output power density beyond the MPE limit of 1.0 mW/cm 2 . In this situation a minimum distance from the antenna needs to be calculated in order to keep the MPE always below the safety limit. The calculation has been done for 4 GHz Carry-Coder II with Power Amp based on the formula mentioned in OET Bulletin 56. The calculations have been done for different commonly used antenna in the Public Safety/ Law enforcement applications. Figure 1 shows the plot of the minimum exposure distance for 5dBi, 16dBi, and 30dBi antennas. The 4 GHz Carry-Coder II with Power Amp transmits the maximum power of 1Watt. The minimum exposure distances are found from the cross points of the exposure graphs (for various antennas) with the line of maximum permissible exposure (i.e. 1 W/cm 2 ). Notice that the numbers in Figure 1 predict the worse case scenario, which is straight in front of the antenna (exposing to the antenna main-lobe). Obviously the side-lobe exposures are well below these numbers as the radiation intensity dramatically reduces on the side lobes. Broadcast Microwave Services Inc. 12367 Crosthwaite Circle, Poway, CA 92064-6817 Phone: 858-391-3050. Toll Free: 800-669-9667. Fax: 858-391-3049. Web: www.bms-inc.com 2 Estimated RF Exposure for 4 GHz Carry-Coder II with Power Amp 0.0 1.0 2.0 3.0 4.0 5.0 0100200300400500600700 Dis tance , cm Power Density, mW/cm^2 Max Permissible Exposure: 1mW/cm 2 30 dBi Antenna Max Exposure at 280 cm 5 dBi Antenna Max Exposure at 20 cm 16 dBi Antenna Max Exposure at 60 cm Figure 1 Summary In order the keep the RF exposure within the FCC limit, it is necessary to maintain the safe distance from the antenna. The results shown in Figures 1 can be summarized in the following table: Antenna Gain (dBi) Minimum permissible distance from antenna (cm) 5 16 30 20 60 280 Notice the above table indicates worst-case situation (straight in front of the antenna).

Nemko USA, Inc. Phone (858) 755-5525 Fax (858) 452-1810 11696 Sorrento Valley Rd., Suite F San Diego, CA 92121-1024 Master: FCC Part 90 Date February 13, 2002 Test Report: 2006 100883 FCC Applicant: Broadcast Microwave Services 12367 Crosthwaite Circle Dock 10 Poway, CA 92064 (858) 391-3050 x147 (858) 391-3049 - fax Equipment Under Test: Model: Carry Coder II Portable COFDM Digital Wireless Camera System with 1Watt Power Amplifier FCC ID: CNVCCII-4H In Accordance With: FCC PART 2 and PART 90 Subpart Y Tested By: Nemko USA Inc. 11696 Sorrento Valley Road San Diego, CA 92121-1024 Date: February 28, 2007 Total Number of Pages: 34 Nemko USA Inc. EQUIPMENT: Carry-Coder II REPORT NO.: 2006 100883 FCC Page 2 of 34 DOCUMENT HISTORY REVISION DATE COMMENTS - February 28, 2007 Prepared By: F.S.Custodio - February 28, 2007 Initial Release: M. T. Krumweide NOTE: Nemko USA, Inc. hereby makes the following statements so as to conform to Chapter 10 (Test Reports) Requirements of ANSI C63.4: 2003 “Methods and Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz”: o The unit described in this report was received at Nemko USA, Inc.'s facilities on October 23, 2006. Testing was performed on the unit described in this report on October 23, 2006 to January 5, 2006. o The Test Results reported herein apply only to the Unit actually tested, and to substantially identical Units. o This report does not imply the endorsement of the Federal Communications Commission (FCC), NVLAP or any other government agency. This Report is the property of Nemko USA, Inc., and shall not be reproduced, except in full, without prior written approval of Nemko USA, Inc. However, all ownership rights are hereby returned unconditionally to Broadcast Microwave Services, and approval is hereby granted to Broadcast Microwave Services and its employees and agents to reproduce all or part of this report for any legitimate business purpose without further reference to Nemko USA, Inc. Nemko USA Inc. EQUIPMENT: Carry-Coder II REPORT NO.: 2006 100883 FCC Page 3 of 34 Table of Contents Section 1. Summary of Test Results.................................................................................5 Section 2. General Equipment Specification..................................................................6 Section 3. RF Power Output................................................................................................7 Section 4. Modulation Characteristics..............................................................................9 Section 5. Occupied Bandwidth.......................................................................................13 Section 6. Spurious Emissions At Antenna Terminals..............................................16 Section 7. Field Strength of Spurious.............................................................................24 Section 8. Frequency Stability..........................................................................................26 Section 9. Test Equipment List.........................................................................................28 APPENDICES PARA. NO.: 2.1055 FREQUENCY STABILITY DATA..........................................................................29 SECTION 6. SPURIOUS EMISSIONS AT ANTENNA TERMINALS........................................................31 Nemko USA Inc. EQUIPMENT: Carry-Coder II REPORT NO.: 2006 100883 FCC Page 4 of 34 CERTIFICATION Nemko USA, Inc., an independent Electromagnetic Compatibility (EMC) Test Laboratory, produced this Test Report and performed the Radio Frequency Interference (RFI) testing and data evaluation contained herein. Nemko USA, Inc.’s measurement facility is currently registered with the United States Federal Communications Commission (FCC) in accordance with the provisions of 47 United States Code (CFR) Part 2, Subpart I, Section 2.948(a). A current description of Nemko USA, Inc.’s measurement facility is on file with the FCC. Nemko USA Inc. has additionally satisfied the FCC that it complies with the requirements set forth in 47 CFR Part 2, Subpart I, Section 2.948(d) regarding the accreditation of EMC laboratories. As a result, the FCC has placed Nemko USA Inc. on its list of EMC laboratories approved to perform Declaration of Conformity (DOC) procedure testing. The RFI testing, test data collection and test data evaluation were accomplished in accordance with the ANSI C63.4: 2003 Standard, and in accordance with the applicable sections of the FCC rules (47 CFR Parts 2 and 18)." digital devices. I hereby certify that the test data, test data evaluation, and equipment configurations used to compile this test report are a true and accurate representation of the test sample’s radio frequency interference characteristics as of the test date(s), and, for the design of the test sample. Mike T. Krumweide, EMC Test Supervisor Nemko USA Inc. EQUIPMENT: Carry-Coder II REPORT NO.: 2006 100883 FCC Page 5 of 34 Section 1. Summary of Test Results General All measurements are traceable to national standards. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC PART 2 and PART 90 Subpart Y. Summary Of Test Data Name Of Test Para. No. Result RF Power Output 90.1215 PASS Modulation Characteristics 2.1047 AS REPORTED* Occupied Bandwidth 90.1213 PASS Spurious Emissions at Antenna Terminals 2.1051/90.210 PASS Field Strength of Spurious Emissions 2.1053 PASS Frequency Stability 2.1055/90.213 AS REPORTED * EUT is a digitally modulated transmitter. Part 90 do not express limits or pass/fail criteria for Modulation Characteristics. Test Conditions: Indoor Temperature: 19--25 °C Humidity: 40-50 % Outdoor Temperature: 18--23 °C Humidity: 40-60 % . Nemko USA Inc. EQUIPMENT: Carry-Coder II REPORT NO.: 2006 100883 FCC Page 6 of 34 Section 2. General Equipment Specification Manufacturer: Broadcast Microwave Services Mode…

Text truncated - open the document above for the full version.