CWU-MVP9IThe MVP-9000i is a touch panel for automation controls

Operation/Reference Guide Touch Panels MVP-9000i 9" Modero ® ViewPoint ® Touch Panel with Intercom Last Revised: 5/18/2011 AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity. AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase, with the following exceptions: •Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay compo- nents are warranted for a period of one (1) year. •Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. •AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX lighting products are under warranty. AMX also guarantees the control of dimmable loads that are properly con- nected to our lighting products. The dimming performance or quality there of is not guaranteed, impart due to the random combi- nations of dimmers, lamps and ballasts or transformers. •AMX software is warranted for a period of ninety (90) days. •Batteries and incandescent lamps are not covered under the warranty. •AMX AutoPatch Epica, Modula, Modula Series4, Modula CatPro Series and 8Y-3000 product models will be free of defects in materials and manufacture at the time of sale and will remain in good working order for a period of three (3) years following the date of the original sales invoice from AMX. The three-year warranty period will be extended to the life of the product (Limited Lifetime Warranty) if the warranty card is filled out by the dealer and/or end user and returned to AMX so that AMX receives it within thirty (30) days of the installation of equipment but no later than six (6) months from original AMX sales invoice date. The life of the product extends until five (5) years after AMX ceases manufacturing the product model. The Limited Lifetime Warranty applies to products in their original installation only. If a product is moved to a different installation, the Limited Lifetime Warranty will no longer apply, and the product warranty will instead be the three (3) year Limited Warranty. All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products returned without a valid RMA number. AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX is not liable for any claim made by a third party or by an AMX Autho- rized Partner for a third party. This Limited Warranty does not apply to (a) any AMX product that has been modified, altered or repaired by an unauthorized agent or improperly transported, stored, installed, used, or maintained; (b) damage caused by acts of nature, including flood, erosion, or earth- quake; (c) damage caused by a sustained low or high voltage situation or by a low or high voltage disturbance, including brownouts, sags, spikes, or power outages; or (d) damage caused by war, vandalism, theft, depletion, or obsolescence. This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of inci- dental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. EXCEPT AS OTHERWISE LIMITED BY APPLICABLE LAW, AMX RESERVES THE RIGHT TO MODIFY OR DISCONTINUE DESIGNS, SPECIFICATIONS, WARRAN- TIES, PRICES, AND POLICIES WITHOUT NOTICE. AMX Software License and Warranty Agreement •LICENSE GRANT. AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, not sold. This license does not grant Licensee the right to create derivative works of the AMX Software. The AMX Software consists of generally available programming and development software, product documenta- tion, sample applications, tools and utilities, and miscellaneous technical information. Please refer to the README.TXT file on the compact disc or download for further information regarding the components of the AMX Software. The AMX Software is sub- ject to restrictions on distribution described in this License Agreement. AMX Dealer, Distributor, …

Text truncated - open the document above for the full version.

5/20/2011 Nemko Canada Inc. 303 River Road Ottawa, Ontario, Canada K1V 1H2 FCC ID: CWU-MVP9I Product Name: MVP-9000i Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Bill of Materials  Operational/Technical Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 20th Day of May 20 11 By: Heath Sharp Signature Printed Title: Product Verification Engineer On behalf of : AMX LLC Telephone: 469.624.8000

5/31/2011 TO: Industry Canada 3701 Carling Ave., Bldg. 94, Ottawa, ON, K2H 8S2 IC: 5078B-MVP9I Models: MVP-9000i-GB, MVP-9000i-GW Declaration of Model Differences To whom it may concern: This letter is to serve as declaration that the only difference between AMX products MVP-9000i-GB and MVP-9000i- GW are the color of the enclosure, where “-GB” stands for black, and “-GW” stands for white. Dated this 31st Day of May 20 11 By: Heath Sharp Signature Printed Title: Product Verification Engineer Telephone: 469.624.6635 Applicant: AMX LLC

1/17/11 MVP-9000i Operational Attestation The MVP-9000i device is capable of operating on channels in the 2.4GHz band that are not available in the US and Canada (channels 12, 13 and 14). The products sold into the US and Canada are configured to only operate on channels 1 through 11 (the channels covered by the application for device authorization/certification) in the 2.4GHz band. The end user has no access to configuration tools that would enable use of the unauthorized channels. Signed, Heath Sharp Product Verification Engineer

1/17/2011 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent FCC On our behalf, I appoint Nemko USA, Inc. at 802 N Kealy Avenue, Lewisville TX 75057 to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides (company name and address). Dated this 17th Day of January 20 11 Agency agreement expiration date: 9/30/2011 By: Heath Sharp Signature Printed Title: Product Verification Engineer On behalf of : AMX LLC

External Photos Front of system (Black enclosure and white enclosure versions) Side of system showing mini USB, USB and power connector Right Side of system Rear of Unit

9.710 .860 .2701.9003.925 8X R.020 91-5967-01BL 91-5967-01WH NOTES: UNLESS OTHERWISE SPECIFIED 3D DATABASE FEATURES TAKE PRECEDENCE OVER 2D DRAWINGS. REFER TO 3D DATABASE FILE (SEE MODEL 1. NAME AND REVISION IN TITLE BLOCK). ALL DIMENSIONS IN INCHES.2. MATERIAL AND COLORS:3. PERMANENT POLYESTER TEXT TO BE ARIAL 6pt. COLOR TO BE PANTONE COLOR GRAY 5C SEE TABLE FOR BACKGROUND COLOR R E V I S I O N S REVECNDESCRIPTIONDATEAPPROVED A16018PROTOTYPE RELEASE2/23/2010J. REAGAN B16969ADD FCC AND IC INFORMATION. ADDED CERTIFICATION LOGOS.9/14/2010J. PORTER C16969ADDED ADDITIONAL TEXT TO LABEL9/20/2010J. PORTER D17228 ADDED COLUMN TO PART TABLE AND NOTE TO INDICATE WHICH FG IS REFERENCED 11/15/2010J. PORTER E17853ADDED MIC LOGO3/25/2011J. PORTER F17871ADDED "MVP-9000i" TEXT3/30/2011J. PORTER GXXXXXADDED UL LOGO. ADDED "MODEL:" TO THE LABEL TEXT.5/9/2011J. PORTER HXXXXXADDED "26GU," "I.T.E.," AND "-GX" TO LABEL TEXT.5/31/2011J. PORTER JXXXXXSHOWING PART SPECIFIC ARTWORK FOR FG AND MODEL NAME7/11/2011J. PORTER PART TABLE PART NUMBERDESCRIPTIONCOLOR 91-5967-01LABEL, SERIAL NUMBERN/A 91-5967-01BLLABEL, SERIAL NUMBER, BLACKPMS BLACK 91-5967-01WHLABEL, SERIAL NUMBER, WHITEWHITE D HGFEDBCA 1 2 3 4 G SCALE HFE .XXX = ± 0.020 .XX = ± 0.03 ANGLES = ± 1° DO NOT SCALE DRAWING SURFACE FLATNESS .003 TIR PER LINEAR INCH ALL DIMENSIONS ARE IN INCHES TOLERANCE ON DECIMAL DIMENSIONS: .X = ± 0.1 UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION DCA 1 2 B 3 4 UNLESS OTHERWISE STATED, THE ARTICLE SPECIFIED SHALL BE RoHS COMPLIANT PER EU DIRECTIVE 2002/95/EC TM AMX LLC 3000 RESEARCH DRIVE RICHARDSON, TX 75082 REV. SHEET DWG. NO.SIZE LABEL, SERIAL NUMBER 91-5967-01 J 1 of 1 2:1 NOTICE: This drawing is the property of AMX LLC. All information contained herein that is not generally known shall be confidential except to the extent the information has been previously established. This drawing may not be copied, reproduced, or used as the basis for manufacture or sale without written permission. 6 1 32 2 24 1 28 1 32 REF ASSEMBLE SERIAL NUMBER LABEL ON BACKSIDE OF KICKSTAND SEE NOTE 3 SEE NOTE 3 27 1 33 2 33 REF FINAL ASSEMBLY TO BE COMPLETED AFTER FINAL TESTING AND/OR BURN-IN D HGFEDBCA 1 2 3 4 G SCALE HFEDCA 1 2 B 3 4 TM AMX LLC 3000 RESEARCH DRIVE RICHARDSON, TX 75082 REV. SHEET DWG. NO.SIZE ENGINEERING ASSEMBLY, 9.0 TOUCH PANEL EA5967-01 A 5 of 5 1:1 NOTICE: This drawing is the property of AMX LLC. All information contained herein that is not generally known shall be confidential except to the extent the information has been previously established. This drawing may not be copied, reproduced, or used as the basis for manufacture or sale without written permission.

Internal Photos Rear of unit with cover removed showing main board with display board behind it Display and main boards – assembly view Radio Card Additional photos showing top and bottom are provided following the antenna close-up shots. Antennas Close-ups are provided on the next page Main Board Display Board Integrated circuit board antenna (top) and Skycross antenna (bottom) Top and Bottom of WiFi radio card used in the system This card is a radio module, but FCC modular approval is not being used when installed in the host device.

© 2011 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 802 N. Twin Oaks Valley Road, Suite 105 • San Marcos, CA 92069 • U.S.A. TEL (760) 471-2100 • FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION AMX LLC Dates of Test: March 2-4, 2011 3000 Research Drive Test Report Number: SAR.20110301 Richardson, TX 75082 Revision A This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2003, OET Bulletin 65 Supp. C, RSS-102 and Safety Code 6 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application is subject to a denial of Federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Certificate # 2387.01 FCC ID: CWU-MVP9I IC Certificate: 5078B-MVP9I Model(s): MVP-9000i-GB, MVP-9000i-GW Module: Silex Model SX-SDCAG FCC ID: N6C-SXSDCAG Test Sample: Engineering Unit Same as Production Serial No.: Beta Equipment Type: Wireless Tablet Computer Classification: Portable Transmitter Next to Body TX Frequency Range: 2412 – 2462 MHz; 5180 – 5240 MHz; 5745 – 5825 MHz Frequency Tolerance: ± 2.5 ppm Maximum RF Output: 2.4 GHz, (b) 16.71 dBm, (g) 17.58 dBm; 5.2 GHz 13.39 dBm; 5.8 GHz 13.12 dBm Conducted Signal Modulation: DSSS, OFDM Antenna Type (Length): Internal(Ant 1 – Skycross P/N 2-3612-A; Ant 2 – On PCB) Application Type: Certification FCC Rule Parts: Part 15C Industry Canada: RSS-102 FCC ID: CWU-MVP9I © 2011 RF Exposure Lab, LLC Page 2 of 139 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Table of Contents 1. Introduction ........................................................................................................................... 3 SAR Definition [5] ...................................................................................................................... 3 2. SAR Measurement Setup ..................................................................................................... 4 Robotic System ......................................................................................................................... 4 System Hardware ..................................................................................................................... 4 System Description ................................................................................................................... 4 E-Field Probe ............................................................................................................................ 5 3. Robot Specifications ............................................................................................................. 7 4. Probe and Dipole Calibration ................................................................................................ 8 5. Phantom & Simulating Tissue Specifications ........................................................................ 9 SAM Phantom ........................................................................................................................... 9 Head & Body Simulating Mixture Characterization ................................................................... 9 Device Holder ........................................................................................................................... 9 Body Worn Configurations ...................................................................................................... 10 6. ANSI/IEEE C95.1 – 1992 RF Exposure Limits [2] ............................................................... 11 Uncontrolled Environment ....................................................................................................... 11 Controlled Environment .......................................................................................................... 11 7. Measurement Uncertainty ................................................................................................... 12 8. System Validation ............................................................................................................... 13 Tissue Verification ................................................................................................................... 13 Test System Verification ......................................................................................................... 13 9. SAR Test Data Summary .................................................................................................... 14 Procedures Used To Establish Test Signal ............................................................................. 14 Device Test Condition ............................................................................................................. 14 SAR Data Summary – 2450 MHz Body .................................................................................. 16 SAR Data Summary – 5200 MHz Body .................................................................................. 17 SAR Data Summary – 5800 MHz Body .................................................................................. 18 10. Test Equipment List ........................................................................................................ 19 11. Conclusion .........................................................…

Text truncated - open the document above for the full version.

Nemko Test Report: 65847RUS1 Applicant: AMX 3000 Research Drive Richardson, TX 75082 USA Equipment Under Test: MVP-9000i (E.U.T.) In Accordance With: FCC Part 15, Subpart C, 15.247 and Industry Canada, RSS-210, Issue 8 Digital Transmission System Transmitter Tested By: Nemko USA, Inc. 802 N. Kealy Lewisville, Texas 75057-3136 TESTED BY: DATE: 17 December 2010 David Light, Senior Wireless Engineer APPROVED BY: DATE: 19 May 2011 Tom Tidwell, Telecom Direct Number of Pages: 64 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 2 of 64 Table of Contents SECTION 1. SUMMARY OF TEST RESULTS 3 SECTION 2. EQUIPMENT UNDER TEST (E.U.T.) 5 SECTION 3. OCCUPIED BANDWIDTH 6 SECTION 4. MAXIMUM PEAK OUTPUT POWER 19 SECTION 5 SPURIOUS EMISSIONS (CONDUCTED) 21 SECTION 6. RADIATED EMISSIONS 35 SECTION 7. PEAK POWER SPECTRAL DENSITY 37 SECTION 8. POWERLINE CONDUCTED EMISSIONS 47 SECTION 9. RECEIVER EMISSIONS 49 SECTION 10. TEST EQUIPMENT LIST 51 ANNEX A - TEST DETAILS 52 ANNEX B - TEST DIAGRAMS 62 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 3 of 64 Section 1. Summary of Test Results Manufacturer: AMX Model No.: MVP-9000i Variants: MVP-9000i-GW (White Plastics) MVP-9000i-GB (Black Plastics) Serial No.: None General: All measurements are traceable to national standards. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15, Subpart C, Paragraph 15.247 and Industry Canada RSS-210, Issue 8 for Digital Transmission Systems. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. New Submission Production Unit Class II Permissive Change Pre-Production Unit THIS TEST REPORT RELATES ONLY TO THE ITEM(S) TESTED. THE FOLLOWING DEVIATIONS FROM, ADDITIONS TO, OR EXCLUSIONS FROM THE TEST SPECIFICATIONS HAVE BEEN MADE. See “ Summary of Test Data”. Nemko USA, Inc. authorizes the above named company to reproduce this report provided it is reproduced in its entirety, for use by the company’s employees only. This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Nemko USA, Inc. is a NVLAP accredited laboratory. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA, Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. This report applies only to the items tested. Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 4 of 64 Summary Of Test Data NAME OF TEST PARA. NO. RESULT Powerline Conducted Emissions 15.207(a)/RSS-Gen 7.2.4 Complies Minimum 6 dB Bandwidth 15.247(a)(2)/A8.2(a) Complies Maximum Peak Power Output 15.247(b)(3)/A8.4(4) Complies Spurious Emissions (Antenna Conducted) 15.247(d)/A8.5 Complies Spurious Emissions (Restricted Bands) 15.209(a)/RSS-Gen 7.2.2 Complies Peak Power Spectral Density 15.247(e)/A8.2(b) Complies Receiver Spurious Emissions RSS-Gen 6.1 Complies Footnotes: Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 5 of 64 Section 2. Equipment Under Test (E.U.T.) General Equipment Information Frequency Band (MHz): 902-928 2400-2483.5 5725-5850 Operating Frequency of Test Sample: 2412 to 2462 MHz and 5745 to 5825 MHz User Frequency Adjustment: Software controlled Description of EUT The AMX MVP-9000i-XX Modero Wireless Touch Panel is a mobile device that communicates with a NetLinx Master via a standard 802.11a/b/g Wireless Access Point. Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 6 of 64 Section 3. Occupied Bandwidth NAME OF TEST: Occupied Bandwidth PARA. NO.: FCC 15.247(a)(2) RSS-210, A8.2(a) TESTED BY: David Light DATE: 13 December 2010 Test Results: Complies. Measurement Data: See 6 dB BW plot Measured 6 dB bandwidth: 12.7 MHz (802.11b) 16.7 MHz (8021.11g) 16.6 MHz (802.11a) Test Conditions: 50 %RH 23 °C Measurement Uncertainty: +/-1x10 -7 ppm Test Equipment Used: 1036-1082-1472 Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 7 of 64 Test Data – Occupied Bandwidth 6 dB Bandwidth 802.11g Channel 1 54 Mbps Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 8 of 64 Test Data – Occupied Bandwidth 802.11g 6 dB Bandwidth Channel 6 54 Mbps Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 9 of 64 Test Data – Occupied Bandwidth 6 dB Bandwidth 802.11g Channel 11 54 Mbps Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 10 of 64 Test Data – Occupied Bandwidth 802.11g 20 dB Bandwidth Channel 6 54 Mbps Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RUS1 Page 11 of 64 Test Data – Occupied Bandwidth 802.11b 11 Mbps Channel 1 6 dB Bandwidth Nemko USA, Inc. FCC PART 15, SUBPART C and Industry Canada, RSS-210, Issue 8 Digital Transmission Systems EQUIPMENT: MVP-9000i Test Report No.: 65847RU…

Text truncated - open the document above for the full version.