CWU-NXR-ZGWNetLinx ZigBee Compatible Gatewayand Repeater

Operation/Reference Guide Control System Accessories NXR-ZGW/-ZRP NetLinx ZigBee Compatible Gateway and Repeater AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX, with the following exceptions: •Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. •Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. •AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX does guarantee the control of dimmable loads that are properly connected to our lighting products. The dimming performance or quality cannot be guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers. •Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year. •AMX Software is warranted for a period of ninety (90) days. •Batteries and incandescent lamps are not covered under the warranty. This warranty extends only to products purchased directly from AMX or an Authorized AMX Dealer. All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products returned without a valid RMA number. AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX is not liable for any claim made by a third party or by an AMX Dealer for a third party. This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. Software License and Warranty Agreement LICENSE GRANT. AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, not sold. This license does not grant Licensee the right to create derivative works of the AMX Software. The AMX Software consists of generally available programming and development software, product documentation, sample applications, tools and utilities, and miscellaneous technical information. Please refer to the README.TXT file on the compact disc or download for further information regarding the components of the AMX Software. The AMX Software is subject to restrictions on distribution described in this License Agreement. LICENSEE MAY NOT SUBLICENSE, RENT, OR LEASE THE AMX SOFTWARE. Licensee may not reverse engineer, decompile, or disassemble the AMX Software. INTELLECTUAL PROPERTY. The AMX Software is owned by AMX and is protected by United States copyright laws, patent laws, international treaty provisions, and/or state of Texas trade secret laws. Licensee may make copies of the AMX Software solely for backup or archival purposes. Licensee may not copy the written materials accompanying the AMX Software. TERMINATION. AMX RESERVES THE RIGHT, IN ITS SOLE DISCRETION, TO TERMINATE THIS LICENSE FOR ANY REASON AND UPON WRITTEN NOTICE TO LICENSEE. In the event that AMX terminates this License, the Licensee shall return or destroy all originals and copies of the AMX Software to AMX and certify in writing that all originals and copies have been returned or destroyed. PRE-RELEASE CODE. Portions of the AMX Software may, from time to time, as identified in the AMX Software, include PRE-RELEASE CODE and such code may not be at the level of performance, compatibility and functionality of the final code. The PRE-RELEASE CODE may not operate correctly and may be substantially modified prior to final release or certain features may not be generally released. AMX is not obligated to make or support any PRE-RELEASE CODE. ALL PRE-RELEASE CODE IS PROVIDED "AS IS" WITH NO WARRANTIES. LIMITED WARRANTY. AMX warrants that the AMX Software will perform substantially in accordance with the accompanying written materials for a period of ninety (90) days from the date of receipt. AMX DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE AMX SOFT…

Text truncated - open the document above for the full version.

FCC ID: CWU-MIOR2 April 26, 2006 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the applicant hereby requests confidential treatment of information accompanying this application as outlined below: 1. Schematics 2. Block Diagram 3. Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the grant for this application. Sincerely, Tuan Tran Compliance Engineer AMX Corp. TEL: 469-624-6632 FAX: 469-624-7159 E-mail: [email protected]

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 May 18, 2007 RE: FCC ID: CWU-NXR-ZGW_ATCB004879 Attention: Tom Tidwell I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please note that page that page 38 of the report states : Part 15.207 – Radio Frequency Devices - Subpart C – Unintentional Radiators.” Please note that Part 15.207 is for intentional radiators and not unintentional radiators. Please explain. 2. Please note that while the FCC may accept CISPR22 conducted data for unintentional radiators, it does not accept EN55022 data for unintentional radiators nor does it accept CISPR22 or EN55022 for intentional radiators. Conducted emissions for intentional radiators must be done in accordance with Part 15.207 and not EN55022 nor CISPR22. This means that in the frequency range between 150kHz to 500kHz the limit is 66 to 56dBuV decreasing linearly with log of frequency. While the limits may be similar, reference to test standards and limits must be correct for the purpose of certification. Please explain why reference to EN55022 conducted test method is made. Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

Labels are made from durable nylon material and affixed with permanent adhesive. Model: NXR-ZGW FCC ID: CWU-NXR-ZGW IC: 5078A-NXR-ZGW This device complies with FCC Part 15 and Industry Canada RSS 210 subject to the following conditions: 1. This device must not cause harmful interference and 2. This device must accept all interference, including interference that interferes with the operation of this device. Model: NXR-ZRP FCC ID: CWU-NXR-ZGW IC: 5078A-NXR-ZGW This device complies with FCC Part 15 and Industry Canada RSS 210 subject to the following conditions: 1. This device must not cause harmful interference and 2. This device must accept all interference, including interference that interferes with the operation of this device. Gateway Label Repeater Label LABEL LOCATION Compliance Label location

Close-up of radio board bottom side Close-up of radio circuit top side Ethernet Interface Board bottom Ethernet Interface Board top

RF Exposure Statement 1. Standard Applicable According to 1.1307 (b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. This is a portable device. 2. Measurement Result: This is a portable device and the max peak output power is 7.08 dBm (.0051 W). Lower than the low threshold 60/f GHz = (24.19 mW), d<2.5 cm general population category. The SAR/MPE measurement is not necessary.

This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full. NTS Plano, 1701 E. Plano Pkwy., Plano, TX 75074 Tel: (972) 509-2566, Fax: (972) 509-0073 Page 1 of 42 Certification Test Report CFR 47 FCC Part 15, Subpart C Section 15.247 and Industry Canada RSS 210, Issue 6 Model: NXR-ZGW Gateway NXR-ZRP Repeater FCC ID.: CWU-NXR-ZGW Project Code: W6373 (Report W6373-WIRELESS-2) Revision: 1 Prepared for: AMX 3000 Research Dr. Richardson, TX 75082 USA Author: Tom Tidwell Issued: 19 December, 2006 1701 E. Plano Parkway, Suite 150 Plano, Texas 75074 Phone: (972) 509-2566 Fax: (972) 509-0073 National Technical Systems Model: NXR-ZGW and NXR-ZRP Compliance Test Report FCC ID.: CWU-NXR-ZGW This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full. NTS Plano, 1701 E. Plano Pkwy., Plano, TX 75074 Tel: (972) 509-2566, Fax: (972) 509-0073 Page 2 of 42 Report Summary NTS Plano Accreditation Numbers: FCC: 101741 IC: 46405-4319 File # IC-4319A-1 Standards A2LA Laboratory Cert. No. 0214.19 Applicant: AMX 3000 Research Dr. Richardson, TX 75082 USA Customer Representative: Tuan Tran EUT Description: EUT Description Manufacturer Model Revision Serial Number The equipment tested is part of a digital transmission system AMX NXR-ZGW NXR-ZRP A 579101PBETA3660020 Model differences: The NXR-ZGW and NXR-ZRP are identical units except that the NXR-ZRP (repeater) unit does not have an active Ethernet interface. Although the NXR-ZRP is called a repeater unit, it is a fully functional transceiver and does not act as a booster or amplifier within the system. The NXR-ZGW model was fully tested to demonstrate compliance of both models. Model: NXR-ZGW and NXR-ZRP Compliance Test Report FCC ID.: CWU-NXR-ZGW This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full. NTS Plano, 1701 E. Plano Pkwy., Plano, TX 75074 Tel: (972) 509-2566, Fax: (972) 509-0073 Page 3 of 42 Test Summary Deviations from: Appendix Test/Requirement Description Base Standard Test Basis NTS Procedure Pass / Fail Applicable Rule Parts A TX 6 dB Bandwidth No No No PASS 15.247 B TX Peak Power Output No No No PASS 15.247 C TX Peak Power Density No No No PASS 15.247 D TX Conducted Spurious Emissions No No No PASS 15.247, 15.205 E TX Conducted Spurious Emissions Band edge No No No PASS 15.247, 15.205 F TX Radiated Spurious Emissions 30 MHz- 25 GHz No No No PASS 15.247, 15.205 G AC Power line Conducted Emissions No No No PASS 15.207 Test Result: The product presented for testing complied with test requirements as shown above. This is to certify that the preceding report is true and correct to the best of my knowledge. Robert Stevens, Tom Tidwell, Quality Assurance Manager Wireless Test Engineer Model: NXR-ZGW and NXR-ZRP Compliance Test Report FCC ID.: CWU-NXR-ZGW This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full. NTS Plano, 1701 E. Plano Pkwy., Plano, TX 75074 Tel: (972) 509-2566, Fax: (972) 509-0073 Page 4 of 42 Table of Contents REPORT SUMMARY........................................................................................................................................................ 2 TEST SUMMARY .................................................…

Text truncated - open the document above for the full version.

Model: NXR-ZGW and NXR-ZRP Compliance Test Report FCC ID.: CWU-NXR-ZGW The test results contained in this report refer exclusively to the product(s) presented for testing. The test results do not cover models or products not referred herein. This test report should not be published or duplicated in whole or part without permission from the testing body and the customer. NTS Plano, 1701 E. Plano Parkway, Suite 150, Plano, Texas 75074 Phone: 972-509-2566 Fax: 972-509-0073 Page 37 of 42 F.11. Test Setup Photo Orientation #1 (Worst-case orientation) Orientation #2 Orientation #3 Powerline Conducted Emissions Test Setup