DC9OPMWWLMicrowave Module

Microwave Module Operation Manual Model : OPMW-WL10525 Company Name : OPTEX CO., LTD. 1. Scope 2. Note and Warning 3. Electrical Specification 4. Pin Assignment 5. FCC Statement & IC Statement 1. Scope This module is designed for motion sensing applications. It consists of Oscillator, Mixer, Filter, detecter and 2element Antennas(T), 2element Antennas(R). In addition, It have Frequency adjustment, Maintenance structure and Shield case. 2. Note and Warning The product is wireless device.It can radiation and receive RF signal. These electric equipments are very sensitive for RF signal in airplane,hospital,and place to life relate. The electric equipments almost interference from RF signal if it not shelter enough and flaw in design. In order to avoid damage for life and property,in compliance with standard of ever place and electric equipment to use the product. If the product collide,operate improper,and maintain by oneself. We are not indemnification. Place responsibility by oneself. 3. Electrical Specification 4. Pin Assignment 1. 2.2V 2. GND 3. IF out 5. FCC Statement & IC Statement FCC Statement Federal Communication Commission Interference Statement Federal Communication Commission Interference StatementFederal Communication Commission Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE: IMPORTANT NOTE:IMPORTANT NOTE: IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: USERS MANUAL OF THE END PRODUCT:USERS MANUAL OF THE END PRODUCT: USERS MANUAL OF THE END PRODUCT: The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. The FCC part 15.19 statement below has to also be available in the manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: LABEL OF THE END PRODUCT:LABEL OF THE END PRODUCT: LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID:DC9OPMWWL ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This Class B digital apparatus complies with Canadian ICES This Class B digital apparatus complies with Canadian ICESThis Class B digital apparatus complies with Canadian ICES This Class B digital apparatus complies with Canadian ICES- -- -003. 003.003. 003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE: IMPORTANT NOTE:IMPORTANT NOTE: IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: USERS MANUAL OF THE END PRODUCT:USERS MANUAL OF THE END PRODUCT: USERS MANUAL OF THE END PRODUCT: The end user has to be informed that the IC radio-frequency exposure guidelines for a…

Text truncated - open the document above for the full version.

Page No. : 21 Limited Module Approval Request Letter Subject: Limited Module Approval Date: 2012/2/21 FCC ID: DC9OPMWWL Dear Reviewer, We, Sporton International Inc., are authorized by OPTEX CO., LTD. to have their state-of-the-art Microwave Module approved under limited module approval authorization. The application of this module is specified to mobile host equipment. The requirements regulated in Public Notice DA00-1407 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 3. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 4. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 5. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 6. The requirement of RF exposure: N/A as exempted due to low output power. Below items have not been fulfilled in module approval request: 1. The requirement of buffered inputs: Not applicable (CW) 2. The requirement of power supply regulation: No own power regulator mounted. Module only to be operated with(in) host devices where a stable power of 2.2 +/- 0.2 V DC can be assured under all operating conditions. Please do not hesitate to contact me for any questions of this request letter. Thank you. Company name : Sporton International Inc. Company Address : No.8, Lane 724, Bo-ai St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Signature : Name : Leo Huang Job Title : Manager

SPORTON International Inc. PAGE NUMBER : 1 OFA2 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 29, 2011 FAX : 886-2-2696-2255 Photographs of EUT SPORTON International Inc. PAGE NUMBER : 2 OFA2 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 29, 2011 FAX : 886-2-2696-2255

SPORTON International Inc. PAGE NUMBER : 1 OFA3 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 29, 2011 FAX : 886-2-2696-2255 Photographs of EUT SPORTON International Inc. PAGE NUMBER : 2 OFA3 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 29, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : 3 OFA3 TEL : 886-2-2696-2468 ISSUED DATE : Dec. 29, 2011 FAX : 886-2-2696-2255

FCC Test Report Report No. : FR1O2801 SPORTON INTERNATIONAL INC. Page No. : 1 of 42 TEL : 886-2-2696-2468 Report Version : Rev. 01 FAX : 886-2-2696-2255 FCC ID DC9OPMWWL FCC Test Report EQUIPMEN : Microwave Module BRAND NAME : OPTEX MODEL NO. : OPMW-WL10525 FCC ID : DC9OPMWWL STANDARD : 47 CFR FCC Part 15.245 APPLICANT : OPTEX CO., LTD. 5-8-12 Ogoto Otsu Shiga 520-0101 Japan MANUFACTURER OPTEX CO., LTD. 5-8-12 Ogoto Otsu Shiga 520-0101 Japan The product sample received on Oct. 28, 2011 and completely tested on Dec. 27, 2011. We, SPORTON, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.10-2009 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Jordan Hsiao 251658240 251658240 FCC Test Report Report No. : FR1O2801 SPORTON INTERNATIONAL INC. Page No. : 2 of 42 TEL : 886-2-2696-2468 Report Version : Rev. 01 FAX : 886-2-2696-2255 FCC ID DC9OPMWWL TABLE OF CONTENTS 1 General Description .............................................................................................................................5 1.1 Information..............................................................................................................................................5 1.2 Additional Information Provided by the Submitter ..................................................................................8 1.3 Ancillary and/or Support Equipment.......................................................................................................9 1.4 EUT Setups ............................................................................................................................................9 1.5 Testing Applied Standards ...................................................................................................................12 1.6 Testing Location ...................................................................................................................................12 1.7 Abbreviations Used for the Test Report ...............................................................................................12 2 Test Configuration of Equipment under Test..................................................................................13 2.1 Test Channel Frequencies ...................................................................................................................13 2.2 Conformance Tests and Related Test Frequencies ............................................................................13 3 Transmitter Test Result .....................................................................................................................14 3.1 AC Power Conducted Emissions .........................................................................................................14 3.2 Occupied Bandwidth ............................................................................................................................19 3.3 Field Strength of Fundamental .............................................................................................................22 3.4 Transmitter Spurious Emissions...........................................................................................................27 3.5 Antenna Requirements.........................................................................................................................40 4 List of Measuring Equipments ..........................................................................................................41 5 Certification of TAF Accreditation ....................................................................................................42 APPENDIX A. TEST PHOTOS...........................................................................................A1 ~ A6 FCC Test Report Report No. : FR1O2801 SPORTON INTERNATIONAL INC. Page No. : 3 of 42 TEL : 886-2-2696-2468 Report Version : Rev. 01 FAX : 886-2-2696-2255 FCC ID DC9OPMWWL SUMMARY OF TEST RESULT FCC Standard Requirements and Conformance Test Specifications Report Clause Ref. Std. Clause Description Result Remark 3.1 15.207 AC Power Conducted Emissions Complied - 3.2 15.215(c) Occupied Bandwidth Complied - 3.3 15.245(b) Field Strength of Fundamental Complied - 3.4 15.245(b) Transmitter Spurious Emissions Complied - 3.5 15.203 Antenna Requirements Complied - 3.6 2.1091 Maximum Permissible Exposure Complied - Note: The EUT only supports TX function, and it does not support pure RX function. FCC Test Report Report No. : FR1O2801 SPORTON INTERNATIONAL INC. Page No. : 4 of 42 TEL : 886-2-2696-2468 Report Version : Rev. 01 FAX : 886-2-2696-2255 FCC ID DC9OPMWWL REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FR1O2801 Rev. 01 Initial issue of report Jan. 03, 2012 FCC Test Report Report No. : FR1O2801 SPORTON INTERNATIONAL INC. Page No. : 5 of 42 TEL : 886-2-2696-2468 Report Version : Rev. 01 FAX : 886-2-2696-2255 FCC ID DC9OPMWWL 1 General Description 1.1 Information 1.1.1 Operating Frequency Range(s) Operating Frequency Range(s) Range 1: 902 – 928 MHz Range 2: 2435 – 2465 MHz Range 3: 5785 – 5815 MHz Range 4: 10.5 – 10.55 GHz Range 5: 24.075 – 24.175 GHz 1.1.2 The Channel Plan(s) The Channel Plan(s) Channel Plan 1: 10.5 – 10.55 GHz Band Nominal Channel Bandwidth 1: 5 MHz, 10.525 GHz Channel Plan 2: N/A Nominal Channel Bandwidth 2: N/A 1.1.3 Transmit Operating Modes The Different Transmit Operating Modes Operating mode 1: Single Antenna Equipment Operating mode 2: Smart Antenna Systems - without beam forming Operating mode 3: Smart Antenna Systems - with beam forming 1.1.4 Smart Antenna Systems In Case of Smart Antenna Systems Smart Antenna Systems: N/A The number of Receive chains: N/A The number of Transmit chains: N/A Equal power dis…

Text truncated - open the document above for the full version.

Report No.: FR1O2801 FCC ID: DC9OPMWWL Page No. : 1 of 6 Appendix A. Test Photos Report No.: FR1O2801 FCC ID: DC9OPMWWL Page No. : 2 of 6 1. Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW Report No.: FR1O2801 FCC ID: DC9OPMWWL Page No. : 3 of 6 SIDE VIEW Report No.: FR1O2801 FCC ID: DC9OPMWWL Page No. : 4 of 6 2. Photographs of Radiated Emissions Test Configuration Test Configuration: 9kHz ~30MHz FRONT VIEW REAR VIEW Report No.: FR1O2801 FCC ID: DC9OPMWWL Page No. : 5 of 6 Test Configuration: 30MHz~1GHz FRONT VIEW REAR VIEW Report No.: FR1O2801 FCC ID: DC9OPMWWL Page No. : 6 of 6 Test Configuration: Above 1GHz FRONT VIEW REAR VIEW