DC9TD-20UINDOOR/OUTDOOR SENSOR TRANSMITTER

2000 Transmission range must be changed according to the environment. Please check if system works properly on the site. In the case of insufficient transmission range, use TR-20U (Repeater unit) to extend range. Receiver/ Repeater RC-20U/ TR-20U TD-20U Note: When you recycle this product, please disassemble product and recycle according to state law. TD-20U INSTALLATION INSTRUCTIONS INDOOR/ OUTDOOR SENSOR TRANSMITTER Please read this manual carefully before installation. 2 PARTS IDENTIFICATION 1 CAUTION 3 TRANSMISSION RANGE (REFERENCE) 2000ft (Open field, line of sight) 150ft (Stucco/Plaster construction) 100ft (Concrete construction) 6. Transmission range Transmission range may decrease under the following conditions: - Either TD-20U or receiving unit installed on a metal surface. - Presence of a steel door, reinforced concrete or other metal obstructions between TD-20U and receiving units. - Places near strong radio sources such as broadcast stations or substation. 7. Battery replacement Replace battery every 2 years. Use only 9V alkaline battery. 8. Cleaning Harsh cleaners such as paint removers or benzene may ruin the surface. Use a soft wet cloth and mild soap to clean. 1. Harsh environments Do not use the TD-20U outdoors under severe conditions as out of warranted temperature, rapid temperature change, high humidity, steam, or smog. This may cause the unit to malfunction. 2. Impact/Shock Impact or Shock can cause severe damage or break the TD-20U. 3. Light/Moving object Direct light or moving objects in front of the TD-20U can cause false alarms. 4. Electric Devices Use the TD-20U at least 3ft(1m) away from any electronic devices such as TVs, Radios, PCs, Microwave ovens or any other devices with an electric motors. This may cause the unit to malfunction. 5. Tampering Any changes or modifications not expressly approved by OPTEX could void the user’s authority to operate the equipment. FEATURES • Compatible with RC-20U(Chime Box W/Relay), TR-20U(Repeater) and any receiver of WIRELESS 1000 series. • 50ft. Long range & 17ft. fan pattern selectable. • Can be installed on the wall, ceiling and desktop. • Weatherproof structure(IP54) for indoor and outdoor applications. • Over 8 million codes possible, eliminates interference from neighbors. • Powered by a 9V alkaline battery(not included). • Supervised low battery. • LED indicator for verifying detection and low battery status. Detection area adjustment knob Inside of rear case Rear case Knockout (for mounting) LONGFAN Detection area pattern display Status indicator Mask Front case Sensor window (lens) FRONTBACK 1) 2) 3) 1) 2) 3) 5 INSTALLATION HINT Fan PatternFront ViewLong RangeFront View Over a doorway Mounted on a counter, looking across a doorway Mounted on a wall, looking across a doorway To cover the area straight ahead or for short range coverage For covering the right or left side Mounted on a counter, looking across a doorway LO NG FAN LONGFAN LONGFAN LONGFAN LO NG FAN LONGFAN LONGFAN LO NG FAN LONGFAN LO NG FAN LO NG FAN LO NG FAN LONG FAN 1 2 345 1 2 3 4 5 How To Choose the detection area pattern 1. Use a screwdriver to open the casing. 2. Choose from the two detection area patterns by pointing the arrow to either . “F: fan pattern” or “L: long range.” 3. Turn the mask to the optimal position for the detection area pattern you have chosen. This mask is adjustable clockwise /counterclockwise (±90°), horizontally (±5°) and vertically (±45°). NOTE: If there is an area within the fan-pattern detection area that you do not want to include, mask part of the lens with a tape. 4 DETECTION AREA PATTERN Fan Pattern(Default setting) Selecting the appropriate detection area pattern for the TD-20U enhances its detection ability and immunity against false alarms. The TD-20U is shipped to you in the fan pattern setting, but you can easily select either fan or long range. Select the long range detection area for Drive-Up announcer applications. Height 8ft (2.5m) 10ft (3m) 13ft (4m) 17ft (5m) Area Width × Length 7ft1ft (2.1m) × (0.3m) 8ft1.3ft (2.5m) × (0.4m) 11ft1.6ft (3.4m) × (0.5m) 14ft2ft (4.2m) × (0.6m) Long RangePet Alley 50ft (15m) 9ft (2.8m) 6ft (1.8m) 2.6ft (80cm)2.6ft (0.8m) LONGFAN Detection direction Detection LONGFAN Detection direction Detection Length Height Width (Long range setting) LONG FAN LONGFAN Unit: inches (mm) • When the power is low, the status indicator starts to flash. Replace the battery in such cases, even if it is less than a year old. • Low power may become the cause of false alarm. • There is no need to readjust the TD-20U or the receiver after replacing batteries. The receiver must be taught this transmittercode before use. Refer to the receiver’s manual for details. 1. Preparation • Press switch 1 of the receiver until the power indicator starts flashing. • Press switch 2 to select the zone you wish to assign to the sensor. 2. Activation • Wave your hand in front of the TD-20U to trigger it. • Verity that the receiver has learned successfully by observing the zone indicat ors of the receiver. Zone indicators should hav s remain topped flashing and continuously 3. Verification • After teaching all the transmitter codes (if you have multiple transmitters), return the receiver to normal operating status. • Make sure that the receiver operates correctly with all the transmitters. Note: Cover the TD-20U until you are ready to teach the receiver. Unwanted detection can cause the TD- 20U to be assigned to the wrong zone and override the data of other transmitters. 1. The system is not operating. Check the transmitter. Does the status indicator light up when you walk in front of the TD-20U? If not, check to see whether the battery is inserted correctly. Otherwise try a new battery. Is the detection area setting appropriate? If not, fix the setup. Is the status indicator flashing? The battery is old. Replace the battery. Check the receiver. Is the power indicator of the receiver lit? Is the receiver on? Check the wi…

Text truncated - open the document above for the full version.

（ （（ （保密要求樣本 保密要求樣本保密要求樣本 保密要求樣本： ：： ：請用公司信紙 請用公司信紙請用公司信紙 請用公司信紙， ，， ，若無公司信紙則要打上公司名稱及地址 若無公司信紙則要打上公司名稱及地址若無公司信紙則要打上公司名稱及地址 若無公司信紙則要打上公司名稱及地址） ）） ） 公 司 名 稱 及 公 司 地 址 公 司 名 稱 及 公 司 地 址公 司 名 稱 及 公 司 地 址 公 司 名 稱 及 公 司 地 址 FCC ID: DC9TD-20U Device Name: INDOOR/OUTDOOR SENSOR TRANSMITTER Model No.: TD-20U Date: 1/18/2010 Federal Communications Commission Dear Sir: Pursuant to Section 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Descriptions The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. By: By: Takumi Sano (Signature) (Printed) Title : Engineer Applicant : OPTEX CO., LTD. Address : 5-8-12, Ogoto Otsu Shiga 520-0101, Japan Tel : +81-77-579-8111 Fax: +81-77-579-8137

（ （（ （授權書樣本 授權書樣本授權書樣本 授權書樣本： ：：請用公司信紙請用公司信紙 請用公司信紙 ，， ， 若無公司信紙則要打上公司名稱及地址若無公司信紙則要打上公司名稱及地址 若無公司信紙則要打上公司名稱及地址） ）） ） 公 司 名 稱 及 公 司 地 址公 司 名 稱 及 公 司 地 址 公 司 名 稱 及 公 司 地 址 FCC ID: DC9TD-20U Device Name: INDOOR/OUTDOOR SENSOR TRANSMITTER Model No.: TD-20U Date: 1/18/2010 Federal Communications Commission To whom it may concern: I, the undersigned, hereby authorize Mr . Joe Hsieh / Application Examiner of ELECTRONICS TESTING CENTER, TAIWAN and hereafter referred to as ETC, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Mr . Joe Hsieh of ETC on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ELECTRONICS TESTING CENTER, TAIWAN as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, By: By: Takumi Sano (Signature) (Printed) Title : Engineer Applicant : OPTEX CO., LTD. Address : 5-8-12, Ogoto Otsu Shiga 520-0101, Japan Tel : +81-77-579-8111 Fax: +81-77-579-8137

FCC ID.: DC9TD-20U Page A1 of A1 IC ID: 4012A-000000TD20U ETC Report No.: 10-01-MAS-174 ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Outside view 1 of EUT 2. Outside view 2 of EUT

ID Label_Location Front Rear

FCC ID.: DC9TD-20U Page B1 of B4 IC ID: 4012A-000000TD20U ETC Report No.: 10-01-MAS-174 ANNEX B: INTERNAL CONSTRUCTION PHOTOS OF EUT 1. Inside View 1 of EUT 2. Inside View 2 of EUT FCC ID.: DC9TD-20U Page B2 of B4 IC ID: 4012A-000000TD20U ETC Report No.: 10-01-MAS-174 3. Inside View 3 of EUT 4. Inside View 4 of EUT FCC ID.: DC9TD-20U Page B3 of B4 IC ID: 4012A-000000TD20U ETC Report No.: 10-01-MAS-174 5. Antenna 6. Antenna FCC ID.: DC9TD-20U Page B4 of B4 IC ID: 4012A-000000TD20U ETC Report No.: 10-01-MAS-174 7. Front view of PCB 8. Rear view of PCB

FCC ID.: DC9TD-20U Sheet 1 of 23 Sheets IC ID: 4012A-000000TD20U ETC Report No. : 10-01-MAS-174 Rev. No 1.0 CONFORMANCE TEST REPORT FOR FCC 47 CFR, Part 15 Subpart C and Canada RSS-210 Report No.: 10-01-MAS-174 Client: OPTEX CO., LTD. Product: INDOOR/OUTDOOR SENSOR TRANSMITTER Model: TD-20U FCC ID: DC9TD-20U IC ID: 4012A-000000TD20U Manufacturer/supplier: IQ Group Sdn. Bhd. Date test item received: 2009/12/24 Date test campaign completed: 2010/01/27 Date of issue: 2010/03/09 The test result only corresponds to the tested sample. It is not permitted to copy this report, in part or in full, without the permission of the test laboratory. Total number of pages of this test report: 23 pages Total number of pages of photos: External photos 1 pages Internal photos 4 pages Setup photos 1 pages Test Engineer Checked By Approved By Perry Lin James Cheng Joe Hsieh ELECTRONICS TESTING CENTER, TAIWAN NO.8, LANE 29, WENMING RD., LESHAN TSUEN, GUISHAN SHIANG, TAOYUAN COUNTY, TAIWAN 33383, R.O.C. TEL: (03) 3276170~4 INT: +886-3-3276170~4 FAX: (03) 3276188 INT: +886-3-3276188 FCC ID.: DC9TD-20U Sheet 2 of 23 Sheets IC ID: 4012A-000000TD20U ETC Report No. : 10-01-MAS-174 Rev. No 1.0 Client : OPTEX CO., LTD. Address : 5-8-12, Ogoto Otsu Shiga 520-0101, Japan Manufacturer : IQ Group Sdn. Bhd. Address : 149, Jalan Sultan Azlan Shah , Taman Perindustrian Bayan Lepas , Fasa 1 ( FTZ ), Bayan Lepas , 11900 Pulau Pinang, Malaysia. EUT : INDOOR/OUTDOOR SENSOR TRANSMITTER Trade name : OPTEX Model No. : TD-20U Power Source : 3V dc Regulations applied : FCC 47 CFR, Part 15 Subpart C (2008) Canada RSS-210 Issue 7 (2007) / RSS-Gen Issue 2 (2007) The testing described in this report has been carried out to the best of our knowledge and ability, and our responsibility is limited to the exercise of reasonable care. This certification is not intended to believe the sellers from their legal and/or contractual obligations. The compliance test is only certified for the test equipment and the results of the testing report relate only to the item tested. The compliance test of this report was conducted in accordance with the appropriate standards. It’s not intention to assure the quality and performance of the product. This report shall not be reproduced except in full, without the approval of ETC. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. Laboratory Introduction: Electronics Testing Center, Taiwan is recognized, filed and mutual recognition arrangement as following: 1 ISO9001: TüV Product Service 2 ISO/IEC 17025: BSMI, CNLA, DGT, NVLAP, CCIBLAC, UL, Compliance 3 Filing: FCC, Industry Canada, VCCI 4 MRA: Australia, Hong Kong, New Zealand, Singapore, USA, Japan, Korea, China, APLAC through TAF 5 FCC Registration Number: 90588, 91094, 91095 h Industry Canada Site Regisitation number: IC 2949A-1 NVLAP Lab Code 200133-0 FCC ID.: DC9TD-20U Sheet 3 of 23 Sheets IC ID: 4012A-000000TD20U ETC Report No. : 10-01-MAS-174 Rev. No 1.0 Table of Contents Page 1. GENERAL INFORMATION ...................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION................................................................................................................................................. 4 1.2 CHARACTERISTICS OF DEVICE:....................................................................................................................................... 4 1.3 TEST METHODOLOGY..................................................................................................................................................... 4 1.4 TEST FACILITY............................................................................................................................................................... 4 1.5 TEST SUMMARY............................................................................................................................................................. 4 2. DEFINITION AND LIMITS ....................................................................................................................................... 5 2.1 DEFINITION.................................................................................................................................................................... 5 2.2 RESTRICTED BANDS OF OPERATION...............................................................................................................................5 2.3 LIMITATION.................................................................................................................................................................... 6 2.4 LABELING REQUIREMENT............................................................................................................................................... 7 2.5 USER INFORMATION....................................................................................................................................................... 7 3. RADIATED EMISSION MEASUREMENT ............................................................................................................. 8 3.1 APPLICABLE STANDARD................................................................................................................................................. 8 3.2 MEASUREMENT PROCEDURE.......................................................................................................................................... 8 3.3 TEST DATA................................................................................................................................................................... 10 3.4 FIELD STRENGTH CALCULATION.................................................................................................................................. 14 3.5 RADIATED TEST EQUIPMENT.......................................................…

Text truncated - open the document above for the full version.

FCC ID.: DC9TD-20U Sheet 1 of 1 Sheets IC ID: 4012A-000000TD20U ETC Report No.: 10-01-MAS-174 Photos of Radiation Measuring Setup