EHA-03CN4Handheld PDA-type device WCDMA/GSM/GPRS/EDGE

Models CN4 and CN4e Compliance Insert The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user’s authority to operate the equipment. Battery Information Battery Recycling Information Note: In the U.S.A., the EPA does not consider spent Li-ion batteries as hazardous waste. Laser Compliance and Precaution The CN4 is registered with the CDRH as a Class I LASER Product (21 CFR Subchapter J, Part 1040 with Laser Notice 50). Note: There are no controls or adjustments provided for routine operation or maintenance of the CN4. Laser and Imager Compliance and Precaution This product complies with the following standards for laser and LED safety: •IEC 60825-1 / EN 60825-1 - Class 1 (embedded laser component < 3 mW) 本產品的使用者必須小心使用 Intermec Technologies Corporation 許可的配件與週邊設備。使用非上述建議的配件，或是在未經 Intermec Technologies Corporation 許可的情況下變更本產品可能會使得本產品的相容性失效，並且使得使用者喪失操作設備的權力。 Caution: This marking indicates that the user should read all included documentation before use. Caution: For use with Intermec battery pack Model(s) AB8, AB9, AB15, and AB16 only. For power supply, use Intermec Model 074246 or AE13 (P/N 851-089-x03). Do not connect and charge the CN4 or CN4e if the temperature is greater than 50°C (122°F). No user-serviceable parts. Caution: The battery pack used with this product may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100 °C (212°F). Do not short circuit; may cause burns. Do not charge batteries in a temperature above 40°C (104°F). Keep away from children. Charge only in or with Intermec Model(s) AC12, AD10, AD11, or AD12. Use of incorrect charger or battery packs may present risk of fire or explosion. Promptly dispose of used battery pack according to the instructions. Li-ionLi-ion This product contains or uses a lithium-ion (Li-ion) main battery. When the battery reaches the end of its useful life, the spent battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information. Caution: There are no user serviceable parts inside the CN4. Use of controls or adjustments, or performances of procedures other than those specified herein, may result in hazardous laser light exposure. 注意：此標誌表示使用者應在使用前先閱讀所有隨附的文件。 注意：僅適用於 Intermec AB8、AB9、AB15 或 AB16 型電池。 請使用 Intermec 074246 或 AE13 (P/N 851-089-x03)型電源。 如果環 境溫度高于 50ºC，切勿連接 CN4 或 CN4e 爲其充電。無使用者可自行維修之零件。 電池資訊 電池回收資訊 雷射和線性影像感應器之相容性與安全措施 本產品符合以下雷射及 LED 安全標準： •IEC 60825-1 / EN 60825-1 - Class 1 （內含的雷射元件 < 3mW） Utilisateurs de ce produit sont avisés d’utiliser des accessoires et des périphériques approuvés par Intermec Technologies Corporation. L’utilisation d’accessoires autres que ceux recommandés ou des changements à ce produit qui ne sont pas approuvés par Intermec Technologies Corporation peuvent annuler la conformité de ce produit et mettre fin au droit qu’a l’usager d’utiliser l’équipement. Informations pour la pile Informations pour le recyclage de la pile Conformité et précautions pour l’utilisation du laser Le CN4 est enregistré auprès du CDRH à titre de produit au laser de Classe I (21 CFR Sous-chapitre J, Partie 1040 avec avis sur le laser 50). La sortie maximale de ce produit est de 1,0 mW à 630-670 nm. Remarque : Il n’y a pas de contrôles ou d’ajustements fournis pour le fonctionnement ou l’entretien périodique du CN4. Conformité et précautions pour l’utilisation du laser et de l’imageur Ce produit est conforme aux normes suivantes visant la sécurité quant au laser: •IEC 60825-1/EN 60825-1 - Classe 1 (composant laser intégré < 3 mW) 注意：此裝置中所用的電池必須小心處理，否則可能會燃燒、造成化學灼傷、爆炸或釋放出有毒物質。請勿焚燒、拆卸或使 其溫度超過 100 °C (212°F)。 環境溫度高于 40ºC 時，切勿對電池充電。請勿短路，否則可能會導致灼傷。請放在兒童拿不到的 地方。 只能使用 Intermec AC14、AD10、AD11 和 AD12 型充電器充電。充電器或電池使用不當可能會引發起火或爆炸。 請依照指示及 時棄置用過的電池。 Li-ionLi-ion 本產品包含或使用鋰 (鋰離子) 主電池。當電池已達其使用壽命，應將其置於合格的回收筒或危險物質的處理裝置中。 請勿將此電池與固體廢棄物混在一起。如需暸解電池的回收或棄置資訊，請聯絡 Intermec Technologies 客服中心。 Attention: Ce marquage indique que l’usager doit, avant l’utilisation, lire toute la documentation incluse. Attention: Pour utilisation avec les bloc-piles AB8, AB9, AB15 et AB16 Intermec exclusivement. Pour l’alimentation, utiliser le modèle Intermec 074246 ou AE13 (N/P 851-089-x03). Ne pas brancher ni charger le CN4 ou le CN4e lorsque la température est supérieure à 50 °C. Ne contient aucune pièce réparable par l’utilisateur. Attention: Le bloc-piles utilisé dans cet appareil peut prendre feu, constituer un risque de brûlure chimique, exploser ou dégager des substances toxiques s’il est manipulé de façon inappropriée. Ne pas jeter au feu, démonter ou chauffer à plus de 100 °C (212 °F). Ne pas court-circuiter; cela pourrait causer des brûlures. Ne pas charger les piles lorsque la température est supérieure à 40 °C. Garder hors de la portée des enfants. Ne charger qu’avec les modèles AC14, AD10, AD11et AD12 d’Intermec. L’utilisation d’un chargeur ou de blocs- piles inappropriés présente un risque d’incendie ou d'explosion. Mettre rapidement au rebut tout bloc-piles usé, conformément aux instructions. Li-ionLi-ion Ce produit contient ou utilise une pile principale au lithium-ion (Li-ion). Lorsque la batterie atteint la fin de sa durée de vie utile, la batterie usées doivent être mises aux rebuts par un agent de recyclage ou un manipulateur de matériaux dangereux agréé. Il ne faut pas mélanger la batterie aux autres déchets solides. Pour plus d’informations sur le recyclage ou la mise aux rebuts, contacter votre centre de services Intermec Technologies. Attention: Le CN4 ne contient aucune pièce réparable par l’utilisateur. L’utilisation de commandes ou de …

Text truncated - open the document above for the full version.

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: Applicant: Intermec Technologies FCC ID: EHA-03CN4 Dear Examiner, Please help to correct technical information in 731 form. 1. Description of Product to be Marketed Correct Description is Handheld device WCDMA/GSM/GPRS/EDGE/802.11bg/BT 2. Equipment Specifications Please add one line of technical entry: 2402-2480 MHz Frequency Range with 0.001629 W output power Please use revised report 09U12493-2B FCC IC BLUETOOTH Report_revised 6-19-2009 Thank you for your kind attention. Best Regards, Claire Hoque Claire Hoque Compliance Certification Services 47173 Benicia Street Fremont, CA 94538, USA Phone: (510) 771-1000 Fax: (510) 661-0888

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 7 CERTIFICATION TEST REPORT* FOR RUGGEDIZED HANDHELD PDA-TYPE DEVICE WITH DUAL BAND GSM/GPRS/WCDMA/HSDPA/HSUPA, 802.11 b/g & BT MODEL NUMBER: CN4, CN4e** FCC ID: EHA-03CN4 IC: 1223A-01CN4 REPORT NUMBER: 09U12493-2A ISSUE DATE: JUNE 11, 2009 Prepared for INTERMEC TECHNOLOGIES CORP 550 SECOND STREET SE CEDAR RAPIDS IOWA, 52401, U.S.A Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 * This report covers the radiated portion of GFSK modulation, the radiated and conducted portions of 8PSK modulation, for conducted portion of GFSK modulation refer to report number ITRM0128.1 ** Model differences are described within the body of this report REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 2 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- 05/11/09 Initial Issue F. Ibrahim A 06/11/09 Revised FCC ID A. Zaffar REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 3 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................... 4 2. TEST METHODOLOGY ........................................................................................................ 5 3. FACILITIES AND ACCREDITATION.................................................................................... 5 4. CALIBRATION AND UNCERTAINTY .................................................................................. 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................... 5 4.2. MEASUREMENT UNCERTAINTY................................................................................ 5 5. EQUIPMENT UNDER TEST ................................................................................................. 6 5.1. DESCRIPTION OF EUT................................................................................................ 6 5.2. DESCRIPTION OF MODEL(S) DIFFERENCES ........................................................... 6 5.3. MAXIMUM OUTPUT POWER....................................................................................... 6 5.4. DESCRIPTION OF AVAILABLE ANTENNAS............................................................... 6 5.5. SOFTWARE AND FIRMWARE..................................................................................... 6 5.6. WORST-CASE CONFIGURATION AND MODE .......................................................... 6 5.7. DESCRIPTION OF TEST SETUP................................................................................. 7 6. TEST AND MEASUREMENT EQUIPMENT ......................................................................... 8 7. ANTENNA PORT TEST RESULTS ...................................................................................... 9 7.1. ENHANCED DATA RATE 8PSK MODULATION.......................................................... 9 7.1.1. 20 dB AND 99% BANDWIDTH.............................................................................. 9 7.1.2. HOPPING FREQUENCY SEPARATION ............................................................ 13 7.1.3. NUMBER OF HOPPING CHANNELS................................................................. 15 7.1.4. AVERAGE TIME OF OCCUPANCY.................................................................... 20 7.1.5. OUTPUT POWER ............................................................................................... 23 7.1.6. AVERAGE POWER ............................................................................................ 27 7.1.7. CONDUCTED SPURIOUS EMISSIONS............................................................. 28 8. RADIATED TEST RESULTS .............................................................................................. 37 8.1. LIMITS AND PROCEDURE ........................................................................................ 37 8.2. TRANSMITTER ABOVE 1 GHz .................................................................................. 38 8.2.1. BASIC DATA RATE GFSK MODULATION......................................................... 38 8.2.2. ENHANCED DATA RATE 8PSK MODULATION ................................................ 47 8.3. RECEIVER ABOVE 1 GHz ......................................................................................... 56 8.4. WORST-CASE BELOW 1 GHz................................................................................... 57 9. SETUP PHOTOS................................................................................................................. 59 REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 4 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: INTERMEC TECHNOLOGIES CORP 550 SECOND STREET SE CEDAR RAPIDS, IOWA, 52401, U.S.A EUT DESCRIPTION: RUGGEDIZED HANDHELD PDA-TYPE DEVICE w/ DUAL BAND GSM/GPRS/WCDMA/HSDPA/HSUPA, 802.11 b/g & BT MODEL: CN4, CN4e SERIAL NUMBER: 03590990181, 03590990054 DATE TESTED: APRIL 23-30, 2009 APPLICABLE STANDARDS STANDARD TEST RESULTS CFR 47 Part 15 Subpart C* Pass INDUSTRY CANADA RSS-210 Issue 7 Annex 8 Pass INDUSTRY CANADA RSS-GEN Issue 2 Pass * This report covers the radiated portion of GFSK mod…

Text truncated - open the document above for the full version.

Intermec Technologies Corporation DHIB August 30, 2006 Report No. ITRM0128.1 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2006 Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Issue Date: August 30, 2006 Intermec Technologies Corporation Model: DHIB Emissions Test Description Specification Test Method Pass Fail Occupied Bandwidth FCC 15.247:2006 ANSI C63.4:2003 Output Power FCC 15.247:2006 ANSI C63.4:2003 Band Edge compliance FCC 15.247:2006 ANSI C63.4:2003 Spurious Conducted Emissions FCC 15.247:2006 ANSI C63.4:2003 Power Spectral Density FCC 15.247:2006 ANSI C63.4:2003 Spurious Radiated Emissions FCC 15.247:2006 ANSI C63.4:2003 AC Powerline Conducted Emissions FCC 15.207:2006 ANSI C63.4:2003 Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400; Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada. Approved By: Greg Kiemel, Director of Engineering This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested, the specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 05/05/03 Revision Number Description Date Page Number 00 None Northwest EMC Accreditations and Authorizations Revision 03/18/05 FCC: Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP: Northwest EMC, Inc. is accredited under the United States Department of Commerce, National Institute of Standards and Technology, and National Voluntary Laboratory Accreditation Program for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 89/336/EEC, ANSI C63.4, MIL- STD 461E, DO-160D and SAE J1113. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. NVLAP LAB CODE 200629-0 NVLAP LAB CODE 200630-0 NVLAP LAB CODE 200676-0 Industry Canada: Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS 212, Issue 1 (Provisional) and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by NIST and recognized by Industry Canada as a Certification Body (CB) per the APEC Mutual Recognition Arrangement (MRA). This allows Northwest EMC to certify transmitters to Industry Canada technical requirements. CAB: Designated by NIST and validated by the European Commission as a Conformity Assessment Body (CAB) to conduct tests and approve products to the EMC directive and transmitters to the R&TTE directive, as described in the U.S. - EU Mutual Recognition Agreement. TÜV Product Service: Included in TUV Product Service Group's Listing of Recognized Laboratories. It qualifies in connection with the TUV Certification after Recognition of Agent's Testing Program for the product categories and/or standards shown in TUV's current Listing of CARAT Laboratories, available from TUV. A certificate was issued to represent that this laboratory continues to meet TUV's CARAT Program requirements. Certificate No. USA0401C. TÜV Rheinland: Authorized to carryout EMC tests by order and under supervision of TÜV Rheinland. This authorization is based on "Conditions for EMC-Subcontractors" of November 1992. Northwest EMC Accreditations and Authorizations Revision 03/18/05 NEMKO: Assessed and accredited by NEMKO (Norwegian testing and certification body) for European emissions and immunity testing. As a result of NEMKO's laboratory assessment, they will accept test results from Northwest EMC, Inc. for product certification (Authorization No. ELA 119). Australia/New Zealand: The National Association of Testing Authorities (NATA), Australia has been appointed by the ACA as an accreditation body to accredit test laboratories and competent bodies for EMC standards. Accredited test reports or assessments by competent bodies must carry the NATA logo. Test reports made by an overseas laboratory that has been accredited for the relevant standards by an overseas accreditation body that has a Mutual Recognition Agreement (MRA) with NATA are also accepted as technical grounds for product conformity. The report should be endorsed with the respective logo of the accreditation body (NVLAP). VCCI: Accepted as an Associate Member to the VCCI, Acceptance No. 564. Conducted and radiated measurement facilities have been registered in accordance with Regulations for Voluntary Control Measures, Article 8. (R…

Text truncated - open the document above for the full version.

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 7 CERTIFICATION TEST REPORT* FOR RUGGEDIZED HANDHELD PDA-TYPE DEVICE WITH DUAL BAND GSM/GPRS/WCDMA/HSDPA 802.11 b/g & BT MODEL NUMBER: CN4, CN4e** FCC ID: EHA-03CN4 IC: 1223A-01CN4 REPORT NUMBER: 09U12493-2, Revision B ISSUE DATE: JUNE 19, 2009 Prepared for INTERMEC TECHNOLOGIES CORP 550 SECOND STREET SE CEDAR RAPIDS IOWA, 52401, U.S.A Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 * This report covers the radiated portion of GFSK modulation, the radiated and conducted portions of 8PSK modulation, for conducted portion of GFSK modulation refer to report number ITRM0128.1 ** Model differences are described within the body of this report REPORT NO: 09U12493-2B DATE: JUNE 19, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 2 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- 05/11/09 Initial Issue F. Ibrahim A 06/11/09 Revised FCC ID A. Zaffar B 06/19/09 Revised EUT Description A. Zaffar REPORT NO: 09U12493-2B DATE: JUNE 19, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 3 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................... 4 2. TEST METHODOLOGY ........................................................................................................ 5 3. FACILITIES AND ACCREDITATION.................................................................................... 5 4. CALIBRATION AND UNCERTAINTY .................................................................................. 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................... 5 4.2. MEASUREMENT UNCERTAINTY................................................................................ 5 5. EQUIPMENT UNDER TEST ................................................................................................. 6 5.1. DESCRIPTION OF EUT................................................................................................ 6 5.2. DESCRIPTION OF MODEL(S) DIFFERENCES ........................................................... 6 5.3. MAXIMUM OUTPUT POWER....................................................................................... 6 5.4. DESCRIPTION OF AVAILABLE ANTENNAS............................................................... 6 5.5. SOFTWARE AND FIRMWARE..................................................................................... 6 5.6. WORST-CASE CONFIGURATION AND MODE .......................................................... 6 5.7. DESCRIPTION OF TEST SETUP................................................................................. 7 6. TEST AND MEASUREMENT EQUIPMENT ......................................................................... 8 7. ANTENNA PORT TEST RESULTS ...................................................................................... 9 7.1. ENHANCED DATA RATE 8PSK MODULATION.......................................................... 9 7.1.1. 20 dB AND 99% BANDWIDTH.............................................................................. 9 7.1.2. HOPPING FREQUENCY SEPARATION ............................................................ 13 7.1.3. NUMBER OF HOPPING CHANNELS................................................................. 15 7.1.4. AVERAGE TIME OF OCCUPANCY.................................................................... 20 7.1.5. OUTPUT POWER ............................................................................................... 23 7.1.6. AVERAGE POWER ............................................................................................ 27 7.1.7. CONDUCTED SPURIOUS EMISSIONS............................................................. 28 8. RADIATED TEST RESULTS .............................................................................................. 37 8.1. LIMITS AND PROCEDURE ........................................................................................ 37 8.2. TRANSMITTER ABOVE 1 GHz .................................................................................. 38 8.2.1. BASIC DATA RATE GFSK MODULATION......................................................... 38 8.2.2. ENHANCED DATA RATE 8PSK MODULATION ................................................ 47 8.3. RECEIVER ABOVE 1 GHz ......................................................................................... 56 8.4. WORST-CASE BELOW 1 GHz................................................................................... 57 9. SETUP PHOTOS................................................................................................................. 59 REPORT NO: 09U12493-2B DATE: JUNE 19, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 4 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: INTERMEC TECHNOLOGIES CORP 550 SECOND STREET SE CEDAR RAPIDS, IOWA, 52401, U.S.A EUT DESCRIPTION: RUGGEDIZED HANDHELD PDA-TYPE DEVICE w/ DUAL BAND GSM/GPRS/WCDMA/HSDPA, 802.11 b/g & BT MODEL: CN4, CN4e SERIAL NUMBER: 03590990181, 03590990054 DATE TESTED: APRIL 23-30, 2009 APPLICABLE STANDARDS STANDARD TEST RESULTS CFR 47 Part 15 Subpart C* Pass INDUSTRY CANADA RSS-210 Issue 7 Annex 8 Pass INDUSTRY CANADA RSS-GEN Issue 2 Pass * This rep…

Text truncated - open the document above for the full version.

REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 59 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 9. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 60 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED RF MEASUREMENT SETUP FOR PORTABLE CONFIGURATION X-AXIS FRONT PHOTO REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 61 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. X-AXIS BACK PHOTO REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 62 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Y-AXIS FRONT PHOTO REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 63 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Y-AXIS BACK PHOTO REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 64 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Z-AXIS FRONT PHOTO REPORT NO: 09U12493-2A DATE: JUNE 11, 2009 FCC ID: EHA-03CN4 IC: 1223A-01CN4 Page 65 of 65 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. END OF REPORT Z-AXIS BACK PHOTO