EHA-RC12ABGNWLAN board

Model: RC12ABGN Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:EHA-RC12ABGN”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Intermec Technologies Corporation 601 Third Street SE Cedar Rapids Iowa 52401-2029 USA TEL: +1 (319) 369-3354 FAX: 319-846-2475 Declaration for no non-US channel operation August 20, 2013 We, Intermec Technologies Corporation, declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: EHA-RC12ABGN If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ----------------------------------- Name: / Title: Kian Meng Lim / Engineer Tel: +65.6303 4972 Fax: +65.6303 2196 E-mail: [email protected]

Date: 2013/04/17 FCC ID: EHA-RC12ABGN Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Kian Meng Lim / Engineer Intermec Technologies Corporation 550 Second Street SE Cedar Rapids Iowa 52401-2029 USA

Agency Authorization Letter Date: 2013/04/17 FCC ID: EHA-RC12ABGN To whom it may concern: We, the undersigned, hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by BV CPS Taoyuan within the scope of this authorization shall have the same effects as our own. This authorization shall expire six months from the original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Kian Meng Lim / Engineer Intermec Technologies Corporation 550 Second Street SE Cedar Rapids Iowa 52401-2029 USA

Date: December 9, 2010 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 To whom it may concern, Agent’s Authorization Letter I, named contact of grantee for Intermec Technologies Corporation, do hereby authorize, until further notice, Kain Meng Lim of Intermec Technologies, to act on my behalf in dealings before the Federal Communications Commission with respect to all matters relating to equipment authorizations under 47 CFR. This authorization maintains that Intermec Technologies Corporation remains responsible for all statements and exhibits in this application. I certify that no party (as defined in 47 CFR 1.2002) to this application, including myself, is subject to a denial of federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 853A. Certified By: Dave Fry Sr. EMC Engineer Intermec Technologies Corporation Dave Fry MS GR05 550 Second Street Cedar Rapids, IA 52401 Desk tel 319.369.3353 Lab tel 319.846.2415 Fax tel 319.846.2475 [email protected] 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

FCC ID: EHA-RC12ABGN Report No.: RF121026C10 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch August 13, 2013 Dear Application Examiner, Intermec Technologies Corporation, It’s a WLAN board, FCC ID: EHA-RC12ABGN, would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in WL1273. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is WL1273. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via an USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was connected with this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: EHA-RC12ABGN Report No.: RF121026C10 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

Intermec Technologies Corp. 802.11 abgn / Bluetooth 2.1 Radio Module Model:RC12ABGN P/N:XXX-XXX-XXX FCC ID: EHA-RC12ABGN

Page 2 Page 3 Page 4 Page 5

FCC ID: EHA-RC12ABGN Report No.: RF121026C10 Operational Description This device is a WLAN board; which operate in 2.4GHz & 5.0GHz band; the maximum data rate could be up to 72.2Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 72.2Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by the 5Vdc from power supply. The antenna is Dipole Antenna with R-TNC antenna connector. The other instruction, please have a look at the users manual.

Report No.: SA111129C16A 1 of 6 Report Format Version 5.0.0 Reference No.: 121026C10 RF EXPOSURE REPORT REPORT NO.: SA111129C16A MODEL NO.: RC12ABGN FCC ID: EHA-RC12ABGN RECEIVED: Oct. 25, 2012 TESTED: Oct. 25 ~ Dec. 06, 2012 ISSUED: Dec. 10, 2012 APPLICANT: Intermec Technologies (S) Pte Ltd ADDRESS: 601 Third Street SE Cedar Rapids Iowa 52401-2029 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA111129C16A 2 of 6 Report Format Version 5.0.0 Reference No.: 121026C10 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................. 4 2. RF EXPOSURE ............................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ......................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................... 5 2.3 CLASSIFICATION ........................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .................................. 6 Report No.: SA111129C16A 3 of 6 Report Format Version 5.0.0 Reference No.: 121026C10 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA111129C16A Original release. Dec. 10, 2012 Report No.: SA111129C16A 4 of 6 Report Format Version 5.0.0 Reference No.: 121026C10 1. CERTIFICATION PRODUCT: WLAN board MODEL: RC12ABGN BRAND: Intermec APPLICANT: Intermec Technologies (S) Pte Ltd TESTED: Oct. 25 ~ Dec. 06, 2012 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: RC12ABGN) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Dec. 10, 2012 Suntee Liu / Specialist APPROVED BY : , DATE : Dec. 10, 2012 Ken Liu / Manager Report No.: SA111129C16A 5 of 6 Report Format Version 5.0.0 Reference No.: 121026C10 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA111129C16A 6 of 6 Report Format Version 5.0.0 Reference No.: 121026C10 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER WLAN: FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 21.60 2.44 20 0.050 1 5180-5240 13.86 3.70 20 0.111 1 5745-5825 21.15 3.70 20 0.061 1 Bluetooth: FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2402-2480 9.05 2.44 20 0.003 1

Report No.: RF111129C16A-2 1 of 47 Report Format Version 5.0.0 Reference No.: 121026C10 FCC TEST REPORT REPORT NO.: RF111129C16A-2 MODEL NO.: RC12ABGN FCC ID: EHA-RC12ABGN RECEIVED: Oct. 25, 2012 TESTED: Oct. 25 ~ Dec. 06, 2012 ISSUED: Dec. 10, 2012 APPLICANT: Intermec Technologies (S) Pte Ltd ADDRESS: 151Lorong Chuan, #05-02A/03, (Lobby C), Singapore 556741 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF111129C16A-2 2 of 47 Report Format Version 5.0.0 Reference No.: 121026C10 Table of Contents RELEASE CONTROL RECORD .............................................................................................................. 4 1. CERTIFICATION ........................................................................................................................... 5 2. SUMMARY OF TEST RESULTS .................................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 6 3. GENERAL INFORMATION ........................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................. 7 3.2 DESCRIPTION OF TEST MODES ............................................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................................... 9 3.3 DESCRIPTION OF SUPPORT UNITS ....................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ........................................................................ 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................ 12 4. TEST TYPES AND RESULTS .................................................................................................... 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................... 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................. 13 4.1.2 TEST INSTRUMENTS ................................................................................................................ 14 4.1.3 TEST PROCEDURES ................................................................................................................ 15 4.1.4 DEVIATION FROM TEST STANDARD ...................................................................................... 15 4.1.5 TEST SETUP .............................................................................................................................. 16 4.1.6 EUT OPERATING CONDITIONS ............................................................................................... 16 4.1.7 TEST RESULTS ......................................................................................................................... 17 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................................. 24 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .......................................................... 24 4.2.2 TEST INSTRUMENTS ................................................................................................................ 24 4.2.3 TEST PROCEDURES ................................................................................................................ 25 4.2.4 DEVIATION FROM TEST STANDARD ...................................................................................... 25 4.2.5 TEST SETUP .............................................................................................................................. 26 4.2.6 EUT OPERATING CONDITIONS ............................................................................................... 26 4.2.7 TEST RESULTS ......................................................................................................................... 27 4.3 NUMBER OF HOPPING FREQUENCY USED .......................................................................... 29 4.3.1 LIMIT OF HOPPING FREQUENCY USED ................................................................................ 29 4.3.2 TEST SETUP ...............…

Text truncated - open the document above for the full version.

Report No.: RF111129C16A 1 of 71 Report Format Version 5.2.0 Reference No.: 121026C10 FCC TEST REPORT (15.247) REPORT NO.: RF111129C16A MODEL NO.: RC12ABGN FCC ID: EHA-RC12ABGN RECEIVED: Oct. 25, 2012 TESTED: Oct. 25 ~ Dec. 06, 2012 ISSUED: Dec. 10, 2012 APPLICANT: Intermec Technologies (S) Pte Ltd ADDRESS: 601 Third Street SE Cedar Rapids Iowa 52401-2029 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF111129C16A 2 of 71 Report Format Version 5.2.0 Reference No.: 121026C10 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 5 1. CERTIFICATION ......................................................................................................................... 6 2. SUMMARY OF TEST RESULTS ................................................................................................ 7 2.1 MEASUREMENT UNCERTAINTY .............................................................................................. 7 3. GENERAL INFORMATION ......................................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................... 8 3.2 DESCRIPTION OF TEST MODES ............................................................................................. 9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................................... 10 3.3 DESCRIPTION OF SUPPORT UNITS ..................................................................................... 14 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................................... 14 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 15 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ............................................................... 16 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 16 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 16 4.1.2 TEST INSTRUMENTS .............................................................................................................. 17 4.1.3 TEST PROCEDURES .............................................................................................................. 18 4.1.4 DEVIATION FROM TEST STANDARD .................................................................................... 18 4.1.5 TEST SETUP ............................................................................................................................ 19 4.1.6 EUT OPERATING CONDITIONS ............................................................................................. 19 4.1.7 TEST RESULTS ....................................................................................................................... 20 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 30 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................ 30 4.2.2 TEST INSTRUMENTS .............................................................................................................. 30 4.2.3 TEST PROCEDURES .............................................................................................................. 31 4.2.4 DEVIATION FROM TEST STANDARD .................................................................................... 31 4.2.5 TEST SETUP ............................................................................................................................ 31 4.2.6 EUT OPERATING CONDITIONS ............................................................................................. 31 4.2.7 TEST RESULTS ....................................................................................................................... 32 4.3 6dB BANDWIDTH MEASUREMENT ........................................................................................ 34 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ..................................................................... 34 4.3.2 TEST SETUP ..........................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF111129C16A-1 1 of 42 Report Format Version 5.1.0 Reference No.: 121026C10 FCC TEST REPORT (15.407) REPORT NO.: RF111129C16A-1 MODEL NO.: RC12ABGN FCC ID: EHA-RC12ABGN RECEIVED: Oct. 25, 2012 TESTED: Oct. 25 ~ Dec. 06, 2012 ISSUED: Dec. 10, 2012 APPLICANT: Intermec Technologies (S) Pte Ltd ADDRESS: 601 Third Street SE Cedar Rapids Iowa 52401-2029 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF111129C16A-1 2 of 42 Report Format Version 5.1.0 Reference No.: 121026C10 TABLE OF CONTENTS RELEASE CONTROL RECORD ......................................…

Text truncated - open the document above for the full version.