EHA-1000CP01X11000CP01UO

1 CN70 Mobile Computer Compliance Insert Model 1000CP01UO The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user’s authority to operate the equipment. Battery and Power Supply Information Laser Compliance and Precaution The 1000CP01UO is registered with the CDRH as a Class II LASER Product (21 CFR Subchapter J, Part 1040). This product has a maximum output of 1 mW at 630-670 nm. Note: There are no controls or adjustments provided for routine operation or maintenance of the 1000CP01UO. Laser and Imager Compliance and Precaution This product complies with the following standards for laser safety: •IEC 60825-1:2007/EN 60825-1:2008-05 : Class 2 (1 mW, 630-670 nm) If applicable, this product will be provided with a set of laser safety labels illustrated on the last page (s) of this document. If the proper label language is not installed on the device, locate and apply the appropriate label over the existing label. Les utilisateurs de ce produit sont mis en garde contre l’utilisation d’accessoires et de périphériques qui ne sont pas approuvés par Intermec Technologies Corporation. L’utilisation d’accessoires autres que ceux recommandés, ou des modifications à ce produit qui ne sont pas approuvées par Intermec Technologies Corporation, peuvent annuler la conformité de ce produit et avoir comme résultat la perte de l’autorité de l’utilisateur à faire fonctionner l’équipement. Information sur les piles et le bloc d’alimentation Conformité et précautions pour l’utilisation du laser Le 1000CP01UO est enregistré auprès du CDRH à titre de produit au laser de Classe II (21 CFR sous-chapitre J, partie 1040). La sortie maximale de ce produit est de 1 mW à 630-670 nm. Remarque: Il n’y a pas de contrôles ou d’ajustements fournis pour le fonctionnement ou l’entretien périodique du 1000CP01UO. Conformité et précautions pour l’utilisation du laser et de l'imageur Ce produit est conforme aux normes suivantes visant la sécurité quant au laser: •IEC 60825-1:2007/EN 60825-1:2008-05 : Class 2 (1 mW, 630-670 nm) Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future reference. Caution: For use with Intermec battery pack Model 1000AB01 (P/N 318-043-001) only. See battery instructions. For power supply, use Intermec Model 9001AE02 (P/N 851-094-xx2) or Model 9002AX02 (P/N 852-071-xx2). No user-serviceable parts. Charge only in Intermec Model 1000CP01UO or with bases 1002UU01, 1002UU02, 1002UU03, 1002UU04, or 1002UU05 using 1002UC01 or 1002UD01 adapters. Use of incorrect charger may present a risk of fire or explosion. Caution: There are no user serviceable parts inside the 1000CP01UO. Use of controls or adjustments, or performance of procedures other than those specified herein, may result in hazardous laser light exposure of up to 1 mW at 630-670 nm. Attention: Cette marque indique que l’utilisateur doit lire toute la documentation incluse avant l’utilisation. Conservez ce supplément pour référence future. Attention: Pour utilisation avec le bloc-piles Intermec 1000AB01 (nº/p 318-043-001) exclusivement. Voir les instructions pour les piles. Pour le bloc d'alimentation CA, utiliser le modèle Intermec 9001AE02 (nº/p 851-094-xx2) ou le modèle 9002AX02 (nº/p 852-071-xx2). Aucune pièce réparable par l’utilisateur. Pour charger, utiliser uniquement le modèles Intermec 1000CP01UO ou les bases 1002UU01, 1002UU02, 1002UU03, 1002UU04 ou 1002UU05 avec les adaptateurs 1002UC01 ou 1002UD01. L’utilisation d’un chargeur inapproprié présente un risque d’incendie ou d'explosion. Attention: Le 1000CP01UO ne contiennent aucune pièce réparable par l’utilisateur. L’utilisation de commandes ou de réglages, ou l’exécution de procédures autres que ce qui est spécifié aux présentes, peut présenter une exposition dangereuse à la lumière laser d'une intensité allant jusqu'à 1 mW à 630-670 nm. 2 Lorsque cela est applicable, ce produit est fourni avec un jeu d’étiquettes de sécurité pour le laser, lesquelles sont illustrées à la ou aux dernières pages du présent guide. Si l’étiquette n’est pas affichée dans la langue appropriée sur le dispositif, localiser et apposer l’étiquette appropriée par-dessus l’étiquette existante. Die Benutzer dieses Produkts werden darauf hingewiesen, nur Zubehörteile und Peripheriegeräte zu verwenden, die von Intermec Technologies Corporation genehmigt sind. Falls nicht empfohlene Zubehörteile verwendet oder an diesem Produkt Änderungen vorgenommen werden, die nicht von Intermec Technologies Corporation genehmigt sind, kann dadurch die behördliche Konformität des Produkts verletzt werden und der Benutzer die Berechtigung zur Verwendung des Geräts verlieren. Informationen über Batterie und Stromversorgung Laser- und Imager-Konformität und Vorsichtsvorkehrungen Dieses Produkt erfüllt die folgenden Standards für Lasersicherheit: •IEC 60825-1:2007/EN 60825-1:2008-05 : Klasse 2 (1 mW, 630-670 nm) Sofern zutreffend, wird dieses Produkt mit einem Satz Laser-Sicherheitsetiketten geliefert, die auf der/den letzten Seite(n) dieser Unterlage abgebildet sind. Wenn am Gerät keine Etiketten in der erforderlichen Sprache vorhanden sind, das entsprechende Etikett aufsuchen und über dem vorhandenen anbringen. Se advierte a los usuarios de este producto que usen accesorios y periféricos aprobados por Intermec Technologies Corporation. El uso de accesorios aparte de los recomendados, o los cambios a este producto que no sean aprobados por Intermec Technologies Corporation, pueden dejar nulo el cumplimiento de este producto y provocar la pérdida de la autoridad del usuario para operar el equipo. Información de la batería y fuente de alimentación Cumplimiento y precaución acerca del…

Text truncated - open the document above for the full version.

Worldwide Headquarters6001 36th Avenue WestEverett, Washington 98203U.S.A.tel 425.348.2600fax 425.355.9551www.intermec.com© 2010 Intermec Technologies Corporation. All rights reserved. 移动计算机快速入门指南 行動電腦快速入門指南 Guide de démarrage rapide de l’ordinateur mobile Mobilcomputer-Kurzanleitung ךירדמ הלחתה הריהמ בשחמל דיינ Panduan Memulai Cepat Komputer Layap モバイルコンピュータクイックスタートガイド 모바일 컴퓨터 빠른 시작 안내서 Manual de Consulta Rápida do Computador Móvel Êðàòêîå ðóêîâîäñòâî Íàëàäîííûé êîìïüþòåð Guía de comienzo rápido para la computadora móvil ค ู่ม ือการเร ิ่มต ้นอย ่างรวดเร ็วส ําหร ับคอมพ ิวเตอร ์ The CN70 ships with a partially charged battery. You will need a DX1, DX2, or DX4 multi-dock and a power supply to charge the battery. CN70 随附一个充有部分电量的电池。您需要使用 DX1、DX2 或 DX4 多底座与电源为电池充电。CN70 隨貨附贈一顆半充電電池。您必須自己準備 DX1、DX2 或 DX4 多基座與電源供應器將電池充飽。Le CN70 est fourni avec une pile partiellement chargée. Vous aurez besoin d’un multi-socle DX1, DX2 ou DX4 et d’un bloc d’alimentation pour charger la pile. Das Modell CN70 wird mit einem teilweise geladenen Akkusatz ausgeliefert. Es wird ein DX1, DX2 oder DX4 Multidock und ein Netzteil zum Laden des Akkus benötigt.ה - CK70 קוושמ םע הללוס הנועט תיקלח . ידכ ןועטל תא הללוסה , קקדזת תנחתל הניגע תבורמ םיסיסב גוסמ DX1 ‏, DX2 וא DX4 קפסלו םרז . CN70 dikirim bersama baterai yang setengah terisi. Anda akan memerlukan dok majemuk DX1, DX2, atau DX4 dan catu daya untuk mengisi baterai.CN70 は、部分充電状態の電池と共に出荷されます。ご使用には DX1、DX2、または DX4 連装ドックのいずれかおよび電池を充電するためのパワーサプライが必要となります。CN70은 부분 충전된 배터리와 함께 제공됩니다. 배터리를 충전하시려면 DX1, DX2, 또는 DX4 멀티-도크 및 전원 공급기가 필요합니다. O CN70 é fornecido com uma bateria parcialmente carregada. Para carregá-la, serão necessárias múltiplas bases DX1, DX2 ou DX e uma fonte de alimentação. CN70 ïîñòàâëÿåòñÿ ñ ÷àñòè÷íî çàðÿæåííîé áàòàðåéêîé. ×òîáû çàðÿäèòü áàòàðåéêó, âàì ïîíàäîáÿòñÿ DX1, DX2 èëè ìíîãîñåêöèîííàÿ ñòîéêà DX4 è áëîê ïèòàíèÿ. El modelo CN70 se envía con una batería parcialmente cargada. Necesitará un multi-acoplador DX1, DX2 ó DX4 y una fuente de alimentación para cargarla. ในร ุ่น CN70 ม ีการชาร ์จแบตเตอร ี่เพ ียงบางส ่วน ค ุณจ ําเป ็นต ้องใช ้ Multi-Dock ร ุ่น DX1, DX2 หร ือ DX4 และพาวเวอร ์ซ ัพพลายในการชาร ์จแบตเตอร . ี่ CN 70 Mobile Computer1000CP01, 1000CP01C, 1000CP01U, 1000CP01UO, 1000CP01W Quick Start Guide CN70 Mobile Computer Quick Start Guide*930-234-001*P/N 930-234-001 Where to Find More Information有关详细信息有關詳細信息Où trouver d’autres détailsVerweise zu weiteren Informationenןכיה אוצמל עדימ ףסונ Tempat Mencari Informasi Lebih Lanjut 詳細にわたる情報について정보를 더 발견하기 위하여 어디에Onde obter mais informaçõesÃäå íàéòè äîïîëíèòåëüíóþ èíôîðìàöèþDónde encontrar más informaciónจะค ้นหาข ้อม ูลมากย ิ่งท ี่ไหน www.intermec.comIn the U.S.A and Canada, call 1.800.755.5505 Caution: See Compliance Insert for use restrictions associated with this product. 警告：有关本产品相关的使用限制，请参阅“符合性插页”。警告：請參見規範插頁中有關本產品使用限制方面的說明。Attention: Consultez la Déclaration de conformité pour les restrictions d’usage associées à ce produit. Vorsicht: Das Konformitätsblatt führt etwaige Verwendungseinschränkungen für dieses Produkt an. הארתה : עדימל לע תולבגה שומיש תורושקה רצומל הז , ןייע ןולעב תומיאתה . Hati-hati: Bacalah Sisipan Kepatuhan tentang pembatasan pemakaian yang terkait dengan produk ini.警告：本製品の使用制限は、適格性に関する折り込みをご参照下さい。조気: 본 제품과 관련된 사용 제한에 대한 자세한 내용은 준수 규정을 참조하십시오. Cuidado: Consulte as informações sobre as restrições de uso associadas a este produto no encarte sobre conformidade. Îñòðîæíî: Ñì. îãðàíè÷åíèÿ, ñâÿçàííûå ñ èñïîëüçîâàíèåì óñòðîéñòâà, íà âêëàäûøå ñ òðåáîâàíèÿìè ïî îáåñïå÷åíèþ ñîîòâåòñòâèÿ. Precaución: Consulte el Inserto de cumplimiento para ver las restricciones de uso asociadas con este producto. ข ้อเต ือน ด ูการใส ่เข ้าส ําหร ับการใช ้ข ้อจ ําก ัดท ี่เก ี่ยวข ้องก ับผล ิตภ ัณฑ ์น . This product is protected by one or more patents. 本产品受到一项或多项专利保护。 本產品受到 一項或多項專利保護。 Ce produit est protege par un brevet ou plus. Dieses Produkt ist durch ein oder mehrere Patente geschutzt. רצומ הז ןגומ טנטפב דחא וא רתוי . Produk ini dilindungi oleh satu atau lebih paten. 本製品は1件またはそれ以上の特許により保護されています。 본 제품은 하나 이상의 특허 권에 의해 보호를 받습니다. Este produto está protegido por uma ou mais patentes. Ýòîò ïðîäóêò çàùèùåí îäíèì èëè íåñêîëüêèìè ïàòåíòàìè. Este producto esta protegido por una o varias patentes. ผล ิตภ ัณฑ ์น ี้ป ้องก ันโดยส ิทธ ิบ ัตรหน ึ่งหร ือมากกว ่า . Electrical rating. 额定电压及电流. 電子規定值。 Cote électrique. Stromversorgung. גוריד למשח . Peringkat kelistrikan. 電流単位。 전기 등급. Especifi cações eléctricas. Ïèòàíèå. Califi cacón eléctrica. อ ัตราอ ิเล ็กทรอน ิกส : x 4,37 / 4,8 V; 2 / 1,5 A CN 70 12 6 9 3 1 2 7 8 10 11 4 5 SIM microSD To synchronize the CN70 with your Windows PC, visit:若要将 CN70 与 Windows PC 同步，请访问：若要將 CN70 與 Windows PC 同步，請訪問：Pour synchroniser le CN70 avec votre PC Windows, allez voir:Für Informationen zum Synchronisieren des Modells CN70 mit Ihrem Windows-PC besuchen Sie bitte: ןורכנסל ה - CN70 םע Windows PC, רקב רתאב : Untuk menyinkronkan CN70 dengan PC Windows, kunjungi:CN70 をお使いの Windows PC と同期させるのには、以下でご参照ください：CN70 를 귀하의 Windows PC 와 연동시키려면, 다음을 방문하세요:Para sincronizar o CN70 com seu PC com sistema operacional Windows, visite:×òîáû ñèíõðîíèçèðîâàòü CN70 ñ ÏÊ, ðàáîòàþùèì â ñèñòåìå Windows, ïîñåòèòå: Para sincronizar el CN70 con su computadora Windows, visite: โปรดด ูว ิธ ีการเช ื่อมข ้อม ูลอ ุปกรณ ์ CN70 ของค ุณเข ้าก ับ Window PC ของค ุณ ได ้ท ี่: www.windowsmobile.com/getstarted

September 30, 2010 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern, Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential documents from public disclosure indefinitely.  Schematics  Theory of Operation  Frequency Block Diagrams  Tune-up Procedure Any exhibit / information for which we have requested confidentiality, but which may not be accorded such treatment by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Sincerely, Todd Van Cleave Manager Engineering Services Carlsbad Research & Development Sierra Wireless America, Inc.

Northwest EMC TCB Compliance Opinion Rev. 12/08/09 INMC0570 Information about the Applicant Grantee (Company Name) Intermec Technologies Corporation FCC Contact Person Dave Fry Address 6001 36th Avenue West City, State, Zip Everett, WA 98203-1264 Job Number INMC0570 Model 1000CP01UO FCC ID EHA-1000CP01X1 Agent Approval Type Original Certification Equipment Class PCE Part 24, Licensed Portable transmitter held to ear Rule Part 22H, 24E Overview This application is for an original filing of Intermec's model CN70 handheld computer with a UMTS radio module model 1000CP01uO, which operated under FCC 47 cfr parts 22H and 24E. Confidentiality requested for allowed files. Request is properly addressed and referenced. Short term confidentiality requested. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature Dave Tolman, TCB Committee 12/15/2010

Date: August 16, 2010 Agent’s Authorization Letter To whom it may concern, I, the undersigned, hereby authorize Wayne Rieger, Lead Engineer, Intermec Technologies Corp. to act on my behalf, as our agent, in the following matters related to the regulatory approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certifications. Any act carried out by Wayne Rieger within the scope of this authorization shall have the same affect as our own. I certify that no party (as defined in 47 CFR 1.2002) to this application, including myself, is subject to a denial of federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 853A. This authorization shall expire 24 months from original date. Certified By: Dave Fry Sr. EMC Engineer 550 Second Street Cedar Rapids, IA 52401 Dave Fry MS GR05 Sr. EMC Engineer tel 319.846.2415 fax 319.846.2475 [email protected] www.intermec.com

Date: November 24, 2010 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 To whom it may concern, Agent’s Authorization Letter I, named contact of grantee for Intermec Technologies Corporation, do hereby authorize, until further notice, Yogendra (Yogi) Shah of Intermec Technologies, to act on my behalf in dealings before the Federal Communications Commission with respect to all matters relating to equipment authorizations under 47 CFR. This authorization maintains that Intermec Technologies Corporation remains responsible for all statements and exhibits in this application. I certify that no party (as defined in 47 CFR 1.2002) to this application, including myself, is subject to a denial of federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 853A. Certified By: Dave Fry Sr. EMC Engineer 550 Second Street Cedar Rapids, IA 52401 Dave Fry MS GR05 Sr. EMC Engineer tel 319.846.2415 fax 319.846.2475 [email protected] www.intermec.com

3 December 2010 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Subject: Original Application FCC ID: EHA-1000CP01X1 Dear Application Examiner: Intermec Technologies Corporation is submitting this application for certification of Model 1000CP01UO, FCC ID: EHA-1000CP01X1. The device is a handheld computer that contains a UMTS radio module. Authorization is sought under FCC Parts 22H and 24E. The device can be used closer than 20 cm to the user’s head or torso so a SAR evaluation was performed. The following SAR and EMC reports have been submitted as part of this application: • NWEMC Test Report # INMC0651: ERP, EIRP, and Radiated Spurious Emissions • CTTL Test Report # I09GW 6944-FCC-EMC: All antenna port direct connect measurements • RF Exposure Test Report # SAR.20101201: SAR Note that the CTTL test report refers to the EUT as the Flextronics MC8795V. This radio is electrically and mechanically identical to the Sierra MC8795V radio module contained in the subject device, ID: EHA-1000CP01X1. The antenna port direct connect data contained in the CTTL report is representative of the subject device, FCC ID: EHA-1000CP01X1. Your efforts in reviewing this application are greatly appreciated. Sincerely, Wayne F. Rieger Radio Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: EHA-1000CP01X1 To Whom It May Concern: Our radio vendor, Sierra Wireless, has requested long-term confidentiality for the following exhibits under a separate letter attached to this application: Schematic Diagrams Block Diagram Operational Description Tune-up Procedure Pursuant to Public Notice DA 04-1705 of the Commission’s policy, we are requesting the commission to grant short-term confidentiality request on the following attachments. This is required in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices: External Photos Internal Photos Test Setup Photos Quick Start Guide Compliance Insert It is our understanding that all measurement test reports, FCC ID label format and correspondent during the certification review process cannot be granted as confidential documents and that information will be available for public review once the grant of equipment authorization is issued. Best regards, Wayne F. Rieger Radio Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203-1264 425-267-2919 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

NORTHWEST EMC, INC. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 January 3, 2011 EHA-1000CP01X1 Dear Application Examiner: We recently completed an upload and issued a grant of equipment authorization for FCC ID EHA-1000CP01X1. The client requested short term confidentiality with the intent that no photos of their product would be viewable by the public. Our policy is to send the entire application package to the customer to do a final review of the exhibits before we upload. The customer did the review and gave us the ok, but unfortunately after looking at the exhibits (after upload) they realized that two of the test reports contained photos of the product. Updated versions of these two reports with the photos removed have been uploaded and should supersede the reports that were originally submitted. Additionally, during the upload the wrong file was selected. The DoC letter has been uploaded and should supersede the External Photos exhibit that was mistakenly uploaded to the Attestation category. Best regards, Northwest EMC, Inc.

P R E - R E L E A S E PRE-RELEASE D RRRRRRRRRRRRRRRRRRRRRRRRRRRRRR RRRRRRRRR A AA F F TTTTT FCC ID: EHA-1000CP01X1 IC: 1223A-1000CP01X1 Patent FCC ID: EHA-1000CP01X1 IC: 1223A-1000CP01X1 Patent 1000CP01UO 1000CP01UO Location of FCC and IC ID Label

External Photos for MC8795V Picture 1: the front view of the sample Picture 2: the back view of the sample External Photos for MC8795V Picture 1: the front view of the sample without shielding cover Picture 2: the back view of the sample without shielding cover

Intermec Radio Group Antenna Measurement System Manufacturer: Laird Technologies Model No: 805-668-001 Serial No: WAN RF Test Fixture Operator: Paul Hulett Comment: NA Main WWAN Test Method: Two-Axis Dual-Polarization Pattern Measurement Type: PIFA Date: 11/10/2110 Summary Page Total Frequency (MHz) 780 800 824 850 869 894 Peak Gain (dBi) -3.53162 -2.20285 -0.484213 0.295376 0.195954 -0.464057 Average Gain (dBi) -6.44448 -5.32961 -3.81917 -3.20924 -3.29624 -3.9979 Average Gain (dBi) -6.44448 -5.32961 -3.81917 -3.20924 -3.29624 -3.9979 Total Frequency (MHz) 915 960 980 1574 1575 1576 Peak Gain (dBi) -1.72232 -4.95514 -6.21709 -2.18289 -2.14646 -2.09221 Average Gain (dBi) -5.4554 -9.05365 -10.4916 -6.36393 -6.38103 -6.33692 Total Frequency (MHz) 1695 1710 1750 1800 1850 1880 Peak Gain (dBi) 3.38486 2.38805 1.95986 1.93766 2.28455 2.06766 Average Gain (dBi) -1.5775 -1.84597 -2.85863 -2.4196 -1.73968 -1.01097 Total Frequency (MHz) 1900 1920 1930 1960 1990 2110 Peak Gain (dBi) 2.71454 2.30739 2.81846 3.01201 3.34611 1.67473 Average Gain (dBi) -0.625208 -0.247921 0.191235 0.256497 -0.270234 -2.90073 Total Frequency (MHz) 2160 2170 2190 2200 Peak Gain (dBi) 1.24144 2.36 2.22694 3.09822 Average Gain (dBi) -2.38225 -2.39256 -2.60534 -2.66813 WAN Free-Space Total EIRP, 780 MHz Total EIRP, Right Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elevation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azimuth = 0.0 Elev ation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elev ation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Y Z Azimuth = 0.0 Elevation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Y Z X Azimuth = 90.0 Elevation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 XY Z Azimuth = -90.0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 800 MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azimuth = 0.0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Y Z Azimuth = 0.0 Elev ation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Y Z X Azimuth = 90.0 Elev ation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 XY Z Azi muth = -9 0. 0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 824 MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azi muth = 0 . 0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Y Z Azimuth = 0.0 Elev ation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Y Z X Azimuth = 90.0 Elev ation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 XY Z Azimuth = -90.0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 850MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 YX Z Azimuth = 0.0 Elevation = 90.0 Roll = 0.0 Tot a l EIRP, Bot t om Vie w EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Y Z Azimuth = 0.0 Elev ation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 Y Z X Azimuth = 90.0 Elev ation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Z Y Azimuth = -90.0 Elevation = 1.0 Roll = 92.0 WAN Free-Space Total EIRP, 869MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Z Y Azimuth = 90.0 Elevation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 YX Z Azimuth = 0.0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 Z X Y Azimuth = -180.0 Elev ation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Y Z Azimuth = 0.0 Elevation = 0.0 Roll = 0.0 Tot a l EI RP , Fr ont Fa c e V i e w EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 Y Z X Azimuth = 90.0 Elevation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 XY Z Azimuth = -90.0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 894MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azi muth = 0 . 0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Y Z Azimuth = 0.0 Elev ation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z Y X Azimuth = 90.0 Elev ation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 XY Z Azimuth = -90.0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 915MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azimuth = 0.0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X…

Text truncated - open the document above for the full version.

© 2010 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 802 N. Twin Oaks Valley Road, Suite 105 • San Marcos, CA 92069 • U.S.A. TEL (760) 471-2100 • FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION Intermec Dates of Test: December 1 - 3, 2010 6001 36 th Avenue West Test Report Number: SAR.20101201 Everett, WA 98203 Revision A This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2003, OET Bulletin 65 Supp. C, RSS-102 and Safety Code 6 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Certificate # 2387.01 FCC ID: EHA-1000CP01X1 IC Certificate: 1223A-1000CP01X1 Model(s): 1000CP01UO Test Sample: Engineering Unit Same as Production Serial No.: 7039 Equipment Type: Wireless Handheld Computer Classification: PCS Licensed Transmitter (PCB) TX Frequency Range: 824.2 – 848.8 MHz, 1850.2 – 1909.8 MHz Frequency Tolerance: ± 2.5 ppm Maximum RF Output: 850 MHz (GSM) – 31.95 dBm, 850 MHz (WCDMA) – 23.01 dBm, 1900 MHz (GSM) – 29.56 dBm 1900 MHz (WCDMA) – 22.35 dBm, Conducted Signal Modulation: GMSK, 8PSK, WCDMA Antenna Type (Length): Internal Application Type: Certification FCC Rule Parts: Part 22, 24 Industry Canada: RSS-102 FCC ID: EHA-1000CP01X1 © 2010 RF Exposure Lab, LLC Page 2 of 198 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Table of Contents 1. Introduction ........................................................................................................................... 3 SAR Definition [5] ...................................................................................................................... 3 2. SAR Measurement Setup ..................................................................................................... 4 Robotic System ......................................................................................................................... 4 System Hardware ..................................................................................................................... 4 System Description ................................................................................................................... 4 E-Field Probe ............................................................................................................................ 5 3. Robot Specifications ............................................................................................................. 7 4. Probe and Dipole Calibration ................................................................................................ 8 5. Phantom & Simulating Tissue Specifications ........................................................................ 9 SAM Phantom ........................................................................................................................... 9 Head & Body Simulating Mixture Characterization ................................................................... 9 Device Holder ........................................................................................................................... 9 6. Definition of Reference Points............................................................................................. 10 Ear Reference Point ........................................................…

Text truncated - open the document above for the full version.