EHA-DDIBDDIB

Important DDIB Radio Information (each caution restriction only needs translated as indicated) English, Simplified Chinese, Traditional Chinese, French-Canadian, Korean, Mexican-dialect of Spanish, Brazilian Portuguese, German, and Russian Caution: This marking indicates that the user should read all included documentation before use. Place this supplement in your manual. Caution: Users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to the product that is not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user’s authority to operate the equipment. 802.11 users Caution: Users are responsible to configure the channels of operation that comply with their country regulatory standards. Wireless Network Administrator should review the operating restrictions detailed within the Access Point installation manual. For Users within North and South America (each caution restriction only needs translated as indicated) English, French Canadian This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that can cause undesired operation. Mexican Spanish is provided below Precaución: Los sistemas, dispositivos o productos que utilicen las bandas de frecuencias del espectro radioeléctrico de uso libre materia del presente Acuerdo, no deberán provocar interferencias perjudiciales a equipos de usuarios que cuenten con permiso o concesión, en cuyo caso deberán cesar su operación hasta que se eliminen las mismas. Asimismo, no tendrán protección contra interferencias provenientes de dichos equipos o de otros que se encuentren debidamente homologados. English, French Canadian, Mexican Spanish Caution: 802.1a Wireless LAN 5.15 to 5.25 GHz (5 GHz radio channels 34 to 48) is restricted to indoor operations to reduce harmful interference to co-channel Mobile Satellite System (MSS) operations. English, French Canadian, Mexican Spanish Radiation Exposure Statement This equipment complies with FCC and Canada RSS-102 radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. Please follow operation instructions as documented for this product. This product meets the RF exposure guidelines when used with the Intermec accessories supplied or designated for this product. Use of other accessories may not ensure compliance with RF exposure guidelines. When installing and using the Intermec DDIB radio module, a 20-cm (8-inch) passing distance must be maintained from the body or head of the user or nearby persons and the antenna. The antenna must not be touched during transmitter operation. When installing the DDIB radio in products defined as “Portable”, the appropriate regulatory testing and approvals are required prior to sales and marketing of the product. The user manual will contain the RF Exposure information for the portable product. For Users In All Other Regions English, French-Canadian, Mexican-Spanish, Brazilian-Portuguese, German, Russia, Simplified Chinese, Traditional Chinese, and Korean. (each caution restriction only needs translated as indicated) Caution: 802.11a Wireless LAN 5.15 to 5.35 GHz is limited to indoor use only. Russian only Caution: Russian Federation 802.11a Wireless LAN 5 GHz operation is limited to 5.15 to 5.35 GHz and 5.65 to 5.725 GHz. Intermec Technologies Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC). • ETSI EN 300 328 • ETSI EN 301 893 • ETSI EN 301 489 • EN 60950 The transmitter module’s output power is 100mW EIRP. The products using this module are intended for business and industrial environments. They should not be used in residential environments and by children. This product is marked with this logo and uses radio frequency bands that are not harmonized throughout the European Community. Bluetooth and 802.11b/g Radio Mode: The transmitter output power is 100mW EIRP. The following table indicates the areas of intended use of the equipment and any known restrictions. (revision REC7003E 200901) Country of Intended Use CEPT Abbr. Yes No License Required Restrictions Details Austria AUT X Belgium BEL X Bulgaria BUL X Cyprus CZE X Czech Republic CYP X Denmark DNK X Estonia EST X Finland FIN X France F X X Outdoor operation restricted to less than 10mW EIRP in 2454 to 2483.5 MHz band Germany D X Greece GRC X Hungary HNG X Ireland IRL X Italy I X General authorization required if used outside own premises Latvia LVA X Lithuania LTU X Luxembourg LUX X General authorization required for network and service supply Malta MLT X Netherlands HOL X Poland POL X Portugal POR X Romania ROU X Slovakia SVK X Slovenia SVN X Spain E X Sweden S X United Kingdom G X Other non-EU: Iceland ISL X Liechtenstein LIE X Norway NOR X X This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Switzerland SUI X 802.11a Radio Mode: The following table indicates the areas of intended use of the equipment and any known restrictions. (revision REC7003E 200901) Note: Dynamic Frequency Selection and Transmit Power Control are required in the 5250 to 5350 MHz and 5470 to 5725 MHz frequency range. Country of Intended Use CEPT Abbr. Yes No License Required Restrictions Details Austria AUT X Belgium BEL X Bulgaria BUL X Cyprus CZE X Czech Republic CYP X Denmark DNK X Estonia EST X Finland FIN X France F X X 5150 to 5350 MHz has limited implementation 5470 to 5725 MHz Relevant+ provisions for the implementation of DFS mechanism described in ETSI standard E…

Text truncated - open the document above for the full version.

31-December-2008 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern, We, Intermec Technologies, hereby attest that the client software and associated drivers used with the DDIB radio module will not initiate any transmission on DFS frequencies. This includes transmissions for beacon ad-hoc peer-to-peer modes. Sincerely, Sean MacKellar Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203-1264 425-356-1765 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

Northwest EMC TCB Compliance Opinion Rev. 9/15/03 INMC0500 Information about the Applicant Grantee (Company Name) Intermec Technologies Corporation FCC Contact Person Dave Fry Address 550 Second Steet SE City, State, Zip Cedar Rapids, IA 52401 Job Number INMC0500 Model DDIB FCC ID EHA-DDIB Agent Sean MacKellar Approval Type Original Equipment Class DTS Digital Transmission System, NII UNII Rule Part 15C, 15E Overview This application is for a single modular approval of a radio module, model DDIB for Intermec Technologies Corporation. This equipment is a dual Bluetooth and 802.11a/b/g radio module, which operates under 47 Cfr parts 15.247 and 15.407. Confidentiality requested for allowed files. Request is properly addressed and referenced. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature Dave Tolman, TCB Committee 1/21/2009

17-November-2008 CONFIDENTIALITY REQUEST CONTAINED WITHIN Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Application for Frequency Hopping Spread Spectrum Transceiver Certification To whom it may concern: Application: Intermec Technologies Corporation, 6001 36 th Avenue West, Everett, Washington 98203-1264 herein submits for Certification of a Direct Sequence Spread Spectrum Transceiver FCC ID: EHA-DDIB. Intermec Technologies Corporation is the manufacturer of this equipment. Confidentiality: Pursuant to Section 0.459 of the Commission's rules (CFR 47), Roving Networks requests confidentiality for portions of the material contained in this application and that the identified material be withheld from public inspection following the grant of this authorization. This material contains Roving Networks trade secrets and confidential information that Roving Networks does not customarily release to the public and which is otherwise not generally available to the pubic. Confidentiality is requested for the following exhibits: • Theory of Operation • Schematics • Frequency Block Diagram Description: This equipment is a dual Bluetooth FHSS and 802.11b/g DSSS radio module, which operates in the 2400- 2483.5 MHz band. Limited modular approval is requested since the radio design allows use in multiple hosts of various configurations. Contact Information: Please contact me by telephone at (425) 356-1765 or by e-mail ([email protected]) if there are questions or additional information needed concerning this filing. Sincerely, Sean MacKellar Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203-1264 425-356-1765 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

19-JANUARY-2009 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Subject: Modular Approval FCC ID: EHA-DDIB Dear Application Examiner: Intermec Technologies Corporation is submitting an application for certification of the DDIB radio, FCC ID: EHA-DDIB. It is a combination 802.11a/b/g and Bluetooth radio module. Modular approval is sought as a DTS device under FCC 15.247 and as a UNII device under FCC 15.407. Your efforts in reviewing this application are greatly appreciated. Please contact me by telephone at (425) 356-1765 or by e-mail ([email protected]) if there are questions or additional information needed concerning this request. Sincerely, Sean MacKellar Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203-1264 425-356-1765 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 November 17, 2008 Dear Application Examiner: Intermec Technologies Corporation is seeking full modular approval of their Model DDIB radio, FCC ID: EHA-DDIB. The radio meets the requirements for full modular approval as detailed in FCC 15.212. Compliance to each of the requirements is described below: 1. “The modular transmitter must have its own RF shielding.” The radio portion of the module is contained in its own RF shielding. The shielding is installed at the factory. Please see the Internal Photos exhibit. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs to insure compliance with Part 15 requirements under conditions of excessive data rates or over-modulation. Please see the Schematics exhibit. 3. “The modular transmitter must have its own power supply regulation.” The EUT has its own power supply regulation to insure compliance with Part 15 requirements regardless of the quality or level of external DC supplying the module from the host unit. Please see Schematics exhibit. Also, the technical report exhibit contains AC power line conducted emissions. 4. “The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c).” The EUT meets the FCC antenna requirements. Please see Antenna information exhibit and photos exhibit. 5. “The modular transmitter must be tested in a stand-alone configuration.” The EUT was tested in a stand-alone configuration. The module was tested outside a host PC, connected via extender card. Please see test setup photos exhibit and technical report exhibit. 6. “The modular transmitter must be labeled with its own FCC ID number.” The EUT is labeled with its own FCC ID number. Please see the photos exhibit. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the User Manual. 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. Please see RF Exposure Exhibits. Please contact me if you have additional questions. Your attention to this matter is greatly appreciated. Best regards, Sean MacKellar Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203-1264 425-356-1765

Compliance with 47 CFR 2.1091 and 15.247 The EUT is a module containing a combination 802.11a/b/g and Bluetooth radio operating under Parts 15.247 and 15.407 in the 2.4, 5 5 GHz bands. The EUT will only be used with a separation distance of 20 centimeters or greater between the antenna and the body of the user or nearby persons and can therefore be considered a mobile transmitter per 47 CFR 2.1091(b). Since the output power is less than 3 W ERP, the EUT is categorically excluded from routine environmental evaluation per 47 CFR 2.1091(c). The MPE estimates are as follows: Table 1 in 47 CFR 1.1310 defines the maximum permissible exposure (MPE) for the general population as 1 mW/cm 2 . The exposure level at a 20 cm distance from the EUT’s transmitting antenna is calculated using the general equation: S = (PG)/4πR 2 Where: S = power density (mW/cm 2 ) P = power input to the antenna (mW) G = numeric power gain relative to an isotropic radiator R = distance to the center of the radiation of the antenna (20 cm = limit for MPE estimates) PG = EIRP Solving for S, the maximum power density 20 cm from the transmitting antenna is summarized in the following table: The power density does not exceed 0.030 mW/cm 2 at 20 cm; therefore, the exposure condition is compliant with FCC rules. MPE Estimate Combination 802.11 a/b/g - Bluetooth Radio Bluetooth Portion Antenna Type Antenna Manufacturer Antenna Part No. Transmit Frequency Max Peak Conducted Output Power Antenna Gain Minimum Antenna Cable Loss Power Density @ 20 cm General Population Exposure Limit from 1.1310 (MHz)(mW)(dBi)(dB) (mW/cm 2 )(mW/cm 2 ) ChipLaird WIC2450-A24003.11200.0011 802.11 a/b/g Portion Antenna Type Antenna Manufacturer Antenna Part No. Transmit Frequency Max Peak Conducted Output Power Antenna Gain Minimum Antenna Cable Loss Power Density @ 20 cm General Population Exposure Limit from 1.1310 (MHz)(mW)(dBi)(dB) (mW/cm 2 )(mW/cm 2 ) 240092.82.100.0301 525027.542.600.0101 582550.83.400.0221 FCC ID: EHA-DDIB OmniLaird WTS2450-RPSMA

Intermec Technologies Corporation DDIB Report No. INMC0500.1 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2008Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: December 19, 2008 Intermec Technologies Corporation Model: DDIB Emissions Test Description Specification Test Method Pass/Fail Spurious Radiated Emissions FCC 15.247 (DTS):2008 ANSI C63.4:2003 KDB No. 558074 Pass Occupied Bandwidth FCC 15.247 (DTS):2008 ANSI C63.4:2003 KDB No. 558074 Pass Power Spectral Density FCC 15.247 (DTS):2008 ANSI C63.4:2003 KDB No. 558074 Pass Spurious Conducted Emissions FCC 15.247 (DTS):2008 ANSI C63.4:2003 KDB No. 558074 Pass Band Edge Compliance FCC 15.247 (DTS):2008 ANSI C63.4:2003 KDB No. 558074 Pass Peak Output Power FCC 15.247 (DTS):2008 ANSI C63.4:2003 KDB No. 558074 Pass AC Powerline Conducted Emissions FCC 15.207:2008 ANSI C63.4:2003 Pass Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834D-2). Approved By: Ethan Schoonover, Sultan Lab Manager NVLAP Lab Code: 200630-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 05/05/03 Revision Number Description Date Page Number 00 None Northwest EMC Accreditations and Authorizations Revision 03/18/05 FCC: Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP: Northwest EMC, Inc. is accredited under the United States Department of Commerce, National Institute of Standards and Technology, and National Voluntary Laboratory Accreditation Program for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 2004/108/EC, and ANSI C63.4. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. NVLAP LAB CODE 200629-0 NVLAP LAB CODE 200630-0 NVLAP LAB CODE 200676-0 NVLAP LAB CODE 200761-0 Industry Canada: Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS-Gen, Issue 2 and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by NIST and recognized by Industry Canada as a Certification Body (CB) per the APEC Mutual Recognition Arrangement (MRA). This allows Northwest EMC to certify transmitters to Industry Canada technical requirements. ( Site Filing Numbers - Hillsboro: 2834D-1, 2834D-2, Sultan: 2834C-1, Irvine: 2834B-1, 2834B-2) CAB: Designated by NIST and validated by the European Commission as a Conformity Assessment Body (CAB) to conduct tests and approve products to the EMC directive and transmitters to the R&TTE directive, as described in the U.S. - EU Mutual Recognition Agreement. Northwest EMC Accreditations and Authorizations Revision 03/18/05 NEMKO: Assessed and accredited by NEMKO (Norwegian testing and certification body) for European emissions and immunity testing. As a result of NEMKO's laboratory assessment, they will accept test results from Northwest EMC, Inc. for product certification (Authorization No. ELA 119). Australia/New Zealand: The National Association of Testing Authorities (NATA), Australia has been appointed by the ACA as an accreditation body to accredit test laboratories and competent bodies for EMC standards. Accredited test reports or assessments by competent bodies must carry the NATA logo. Test reports made by an overseas laboratory that has been accredited for the relevant standards by an overseas accreditation body that has a Mutual Recognition Agreement (MRA) with NATA are also accepted as technical grounds for product conformity. The report should be endorsed with the respective logo of the accreditation body (NVLAP). VCCI: Accepted as an Associate Member to the VCCI, Acceptance No. 564. Conducted and radiated measurement facilities have been registered in accordance with Regulations for Voluntary Control Measures, Article 8. (Registration Numbers. - Hillsboro: C-1071, R-1025, C- 2687, T-289, and R-2318, Irvine: R-1943, C-2766, and T-298, Sultan: R-871, C-1784, and T- 294). BSMI: Northwest EMC has been designated by NIST and validated by C-Taipei (BSMI) as a CAB to conduct tests as described in the APEC Mutual Recognition Agreement (US0017). License No.SL2-IN-E-1017. GOST: Nor…

Text truncated - open the document above for the full version.

Intermec Technologies Corporation DDIB Report No. INMC0500.2 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2008Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: December 13, 2008 Intermec Technologies Corporation Model: DDIB Emissions Test Description Specification Test Method Pass/Fail Spurious Radiated Emissions FCC 15.247 (FHSS):2008 ANSI C63.4:2003 DA 00-705:2000 Pass Occupied Bandwidth FCC 15.247 (FHSS):2008 ANSI C63.4:2003 DA 00-705:2000 Pass Output Power FCC 15.247 (DTS):2008 ANSI C63.4:2003 KDB No. 558074 Pass Power Spectral Density FCC 15.247 (DTS):2008 ANSI C63.4:2003 KDB No. 558074 Pass Spurious Conducted Emissions FCC 15.247 (FHSS):2008 ANSI C63.4:2003 DA 00-705:2000 Pass Band Edge Compliance FCC 15.247 (FHSS):2008 ANSI C63.4:2003 DA 00-705:2000 Pass AC Powerline Conducted Emissions FCC 15.207:2008 ANSI C63.4:2003 Pass Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834D-2). Approved By: Ethan Schoonover, Sultan Lab Manager NVLAP Lab Code: 200630-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 05/05/03 Revision Number Description Date Page Number 00 None Northwest EMC Accreditations and Authorizations Revision 03/18/05 FCC: Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP: Northwest EMC, Inc. is accredited under the United States Department of Commerce, National Institute of Standards and Technology, and National Voluntary Laboratory Accreditation Program for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 2004/108/EC, and ANSI C63.4. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. NVLAP LAB CODE 200629-0 NVLAP LAB CODE 200630-0 NVLAP LAB CODE 200676-0 NVLAP LAB CODE 200761-0 Industry Canada: Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS-Gen, Issue 2 and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by NIST and recognized by Industry Canada as a Certification Body (CB) per the APEC Mutual Recognition Arrangement (MRA). This allows Northwest EMC to certify transmitters to Industry Canada technical requirements. ( Site Filing Numbers - Hillsboro: 2834D-1, 2834D-2, Sultan: 2834C-1, Irvine: 2834B-1, 2834B-2) CAB: Designated by NIST and validated by the European Commission as a Conformity Assessment Body (CAB) to conduct tests and approve products to the EMC directive and transmitters to the R&TTE directive, as described in the U.S. - EU Mutual Recognition Agreement. Northwest EMC Accreditations and Authorizations Revision 03/18/05 NEMKO: Assessed and accredited by NEMKO (Norwegian testing and certification body) for European emissions and immunity testing. As a result of NEMKO's laboratory assessment, they will accept test results from Northwest EMC, Inc. for product certification (Authorization No. ELA 119). Australia/New Zealand: The National Association of Testing Authorities (NATA), Australia has been appointed by the ACA as an accreditation body to accredit test laboratories and competent bodies for EMC standards. Accredited test reports or assessments by competent bodies must carry the NATA logo. Test reports made by an overseas laboratory that has been accredited for the relevant standards by an overseas accreditation body that has a Mutual Recognition Agreement (MRA) with NATA are also accepted as technical grounds for product conformity. The report should be endorsed with the respective logo of the accreditation body (NVLAP). VCCI: Accepted as an Associate Member to the VCCI, Acceptance No. 564. Conducted and radiated measurement facilities have been registered in accordance with Regulations for Voluntary Control Measures, Article 8. (Registration Numbers. - Hillsboro: C-1071, R-1025, C- 2687, T-289, and R-2318, Irvine: R-1943, C-2766, and T-298, Sultan: R-871, C-1784, and T- 294). BSMI: Northwest EMC has been designated by NIST and validated by C-Taipei (BSMI) as a CAB to conduct tests as described in the APEC Mutual Recognition Agreement (US0017). License No.SL2-IN-E-1017. GOST: Nort…

Text truncated - open the document above for the full version.

Intermec Technologies Corporation DDIB Report No. INMC0500 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2008Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: December 19, 2008 Intermec Technologies Corporation Model: DDIB Emissions Test Description Specification Test Method Pass/Fail Spurious Radiated Emissions FCC 15.407:2008 ANSI C63.4:2003 DA 02-2138:2002 Pass Spurious Radiated Emissions FCC 15.209:2008 ANSI C63.4:2003 Pass Peak Power Spectral Density FCC 15.407:2008 ANSI C63.4:2003 DA 02-2138:2002 Pass Emission Bandwidth FCC 15.407:2008 ANSI C63.4:2003 DA 02-2138:2002 Pass Peak Excursion FCC 15.407:2008 ANSI C63.4:2003 DA 02-2138:2002 Pass AC Powerline Conducted Emissions FCC 15.407:2008 ANSI C63.4:2003 DA 02-2138:2002 Pass Frequency Stability FCC 15.407:2008 ANSI C63.4:2003 DA 02-2138:2002 Pass Peak Transmit Power FCC 15.407:2008 ANSI C63.4:2003 DA 02-2138:2002 Pass Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834D-2). Approved By: Ethan Schoonover, Sultan Lab Manager NVLAP Lab Code: 200630-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 05/05/03 Revision Number Description Date Page Number 00 None Northwest EMC Accreditations and Authorizations Revision 03/18/05 FCC: Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications i…

Text truncated - open the document above for the full version.