EHA-RC12BGNWLAN board

Document
Number:
XXXXX

Communications
Systems Communications
SystemsCommunications
Systems Communications
Systems



Statement
Statement
Statement
Statement
of
Work: of
Work:of
Work: of
Work:



Specifications
for
a
SDIO
Specifications
for
a
SDIO
Specifications
for
a
SDIO
Specifications
for
a
SDIO
802.11
802.11
802.11
802.11
b/g b/gb/g b/g/n /n/n /n



Wireless
LAN Wireless
LANWireless
LAN Wireless
LAN



and
Bluetooth
and
Bluetooth
and
Bluetooth
and
Bluetooth
2.1
Network
I 2.1
Network
I2.1
Network
I 2.1
Network
Interface
Land
Grid
nterface
Land
Grid
nterface
Land
Grid
nterface
Land
Grid
Array
Module Array
ModuleArray
Module Array
Module



Revision:

A
10/7/2011

Intermec
Engineering





































1 PURPOSE This document describes the hardware design specifications of the Wireless abgn + Bluetooth option board for the Phoenix program.
1.1 System Block Diagram 1.2 Interfaces 1.2.1 Connector to Main Board Through a 30pin connector, right angle, 2mm pitch Input/Output direction is referenced from the view of the option board: •
Input: from the MLB to the option board •
Output: from option board to MLB Pin # Description I/O Pin # Description I/O 1 5V 2 5V 3 GND 4 GND 5 GND 6 SD_CMD IO 7 GND 8 SD_D0 IO 9 GND 10 SD_D1 IO 11 GND 12 SD_D2 IO 13 GND 14 SD_D3 IO 15 GND 16 SD_CLK I 17 GND 18 GND 19 WIFI_PWR I 20 BT_PWR I 21 WLAN_IRQ O 22 BT_RX I 23 SCL I 24 BT_TX O 25 SDA IO 26 BT_RTS 27 BT_IRQ O 28 BT_CTS 29 GND 30 GND 1.2.2 RF Coaxial connector RP-TNC Connector, Right Angle, Jack Bulkhead from DynaHz. MPN: 26-800x-11040. Current MPN is 26-8003-11040. IPN: 351-486-001 1.2.3 Interface to Galileo module Refer to [1] “Galileo abgn System Specifications.doc”, referred as CDC doc# “636425” for the complete description of the interface to Galileo module. Below is an extract of the important signals to communicate to the Galileo module. Input/Output direction is referenced from the view of the Galileo module: •
Input: from the carrier board to Galileo •
Output: from Galileo to carrier board Pin # Description I/O Remark 7 Vbat I 8 Vbat I 16 32kHz_CLK I 20 VDDIO I 32 VDDIO I 39 BATTERY_OK I 43 BT+PWR_EN I Active high 45 802.11_PWR_EN I 52 2.4_5GHz_RF I/O 50 Ohm RF I/O 61 BT_RX I 62 BT_TX O 63 BT_PCM_VFS I/O Pull-low 64 SD_D3 I/O 65 SD_D1 I/O 66 SD_CLK I 67 SD_D2 I/O 68 WLINK_TX O 74 BT_CTS I 75 BT_PCM_VDR I Pull-low 77 SD_CMD I/O 78 SD_D0 I/O 80 WLINK_RX I 83 BT_RTS O 84 N.C. - Previously BT_IRQ 85 BT_PCM_VCK I/O Pull-low 86 BT_PCM_VDX O floating 87 BT_EN I Active high 89 WLAN_IRQ O Active low 1.3 Power supply The option board received a 5V power supply from the MLB. It generates from it a 3.3V/1.2A supply and a 1.8V/0.8A used by the carrier board and the Galileo module. 1.3.1 Regulator 3.3V From 5V, generate 3,3V power supply used by the Galileo module and the level-shifter. 1.3.2 Regulator 1.8V From 3.3V, generate 1.8V power supply used by the Galileo module, the slow clock and the level-shifter. 1.4 Level shifter The level shifter is used to change the 1.8V signals coming from the Galileo module to a 3.3V signals compliant with the MLB signal requirements, and vice-versa. The signals converted from 3.3V to 1.8V and 1.8V to 3.3V are as followed: •
WIFI_PWR •
WLAN_IRQ •
BT_PWR •
BT_RX •
BT_TX •
BT_RTS •
BT_CTS Notes: (1)
The CPU on the MLB is configured to work with 1.8V signals. In this case the SDIO signals out of the Galileo module do not need to be modified. (2)
Provision is made to convert the CLK_32kHz and all SDIO signals via the level shifter through uncounted resistors. 1.5 Clock 1.5.1 32kHz Slow clock for the Galileo module 1.5.2 26MHz Internal fast clock of the Galileo module
This
document
is
intended
for
Intermec
Development
Engineering
and
System
Test
Engineering.
This
document
contains
information
regarding
the
design,
development
and
testing
of
a
SDIO
based
IEEE
802.11
bgn
and
High
Speed
UART
Bluetooth
network
interface
MODULE
based
on
a
newly
developed
Intermec
Wireless
platform
name
Galileo.

This
variant
is
named
Galileo
Galileo
Galileo
Galileo
bg bgbg bgn nn n




2 RC12 Overview
R RR RC12
C12
C12
C12
is
an
embedded
wireless
device
platform
that
uses
a
90
PAD
Land
Grid
Array
(LGA)
form
factor
to
allow
for
a
low
cost
solution
to
mount
highly
integrated
chipsets
or
OEM/ODM
MODULES MODULESMODULES MODULES
onto
Intermec
products.

Galileo
uses
solder7down
re7flow
mounting
only
to
a
host
MLB
–
there
are
no
screws,
digital
or
RF
connectors.

Test
jigs
are
required
to
operate
Galileo
outside
of
a
product.






































Figure
Figure
Figure
Figure
1 11 1:
RC12
platform :
RC12
platform:
RC12
platform :
RC12
platform




The
RC12 The
RC12The
RC12 The
RC12
is
an
Intermec
designed
radio
platform
incorporating
the
MuRata
WLAN/Bluetooth
radio
module
LBEH1Z9PFC TEMP.


Please
see
reference
section
for
data
sheet.

This
device
is
a
dual
function
IEEE
802.11
bgn
transceiver,
a
Bluetooth
2.1
compliant
radio
transceiver.

The
module
contains
independent
transceivers
for
each
radio
technology;
IEEE
802.11
and
Bluetooth.

This
variants
system
is
capable
of
operating
at
the
2.4
GHz
for
the
IEEE
802.11
transceiver,
or
2.4
GHz
band
for
the
Bluetooth
transceiver.


The
MuRata
MODULE
is
based
on
the
following
802.11
and
Bluetooth
chipsets
from
Texas
Instruments;

WL1273

Single7Chip
MAC
baseband
processor
and
RF
transceiver
supporting
802.11
b/g/n
standard

The
RC12 The
RC12The
RC12 The
RC12
and
subsequent
variants
will
be
manufactured
by
Contract
manufacturer.

Intermec
is
responsible
for
ensuring
proper
manufacturing
test
of
the
current
and
future
designs.
2.1 IEEE802.11 transceiver description The
IEEE
802.11
transceiver
is
based
on
the
Texas
Instruments
WL1273
s…

Text truncated - open the document above for the full version.

Important RC12BGN Radio Information Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future reference. 802.11 Users Caution: Users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to the product that is not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user’s authority to operate the equipment. Caution: Users are responsible for configuring the channels of operation that comply with their country regulatory standards. Wireless Network Administrator should review the operating restrictions detailed within the Access Point installation manual. 802.11 用户 用户用户 用户 注意：该标记指示在使用之前用户应阅读所有包含的文档。请保留这份补充材料，以备日后参考。 注意：敬告本产品的用户，请务必使用 Intermec Technologies Corporation 许可的附件和外围设备。 如果使 用推荐附件之外的其 它附件，或未经 Intermec Technologies Corporation 许可而擅自改装本产品，都可能会 使本产品的符合性无效，并可能会导致用户失去操作本设备的权利。 802.11 使用者 使用者使用者 使用者 注意：用户负责根据所在国家/ 地区的法规标准配置操作信道。无线网络管理员必须仔细阅读《接入点安装手 册》中有关操作限制的详细信息。 注意：此標誌表示使用者應在使用前先閱讀所有隨附的文件。 請保留這份補充材料，以備日後參考。 注意： 本產品的使用者必須小心使用 Intermec Technologies Corporation 許可的配件與週邊設備。使用非上 述建議的配件，或是在未經 Intermec Technologies Corporation 許可的情況下變更本產品可能會使得本產品 的相容性失效，並且使得使用者喪失操作 設備的權力。 注 意： 使 用 者 負 責 根 據 所 在 國 家/ 地 區 的 法 規 標 準 配 置 操 作 通 道。 無 線 網 路 管 理 員 必 須 檢 閱《 接 入 點 安 裝 手 冊》內有關操作限制的詳細資訊。 Utilisateurs du 802.11 Attention: Ce marquage indique que l’usager doit, avant l’utilisation, lire toute la documentation incluse.Conservez ce supplément pour référence future. Attention: Utilisateurs de ce produit sont avisés d’utiliser des accessoires et des périphériques approuvés par Intermec Technologies Corporation. L’utilisation d’accessoires autres que ceux recommandés ou des changements à ce produit qui ne sont pas approuvés par Intermec Technologies Corporation peuvent annuler la conformité de ce produit et mettre fin au droit qu’a l’usager d’utiliser l’équipement. Attention: Il incombe aux utilisateurs de configurer les canaux de fonctionnement de manière à ce qu’ils se conforment aux normes réglementaires de leur pays. L’administrateur du réseau sans fil doit revoir les restrictions de fonctionnement indiquées en détail au manuel d’installation du point d’accès. Vorsicht: Diese Kennzeichnung weist darauf hin, dass der Benutzer vor dem Gebrauch alle mitgelieferten Unterlagen lesen soll. Diese Ergänzung muss zur zukünftigen Bezugnahme aufgehoben werden. Vorsicht: Die Benutzer dieses Produkts werden darauf hingewiesen, nur Zubehörteile und Peripheriegeräte zu verwenden, die von Intermec Technologies Corporation genehmigt sind. Falls nicht empfohlene Zubehörteile verwendet oder an diesem Produkt Änderungen vorgenommen werden, die nicht von Intermec Technologies Corporation genehmigt sind, kann dadurch die behördliche Konformität des Produkts verletzt werden und der Benutzer die Berechtigung zur Verwendung des Geräts verlieren. 802.11 Benutzer Vorsicht: Benutzer sind dafür verantwortlich, die Betriebskanäle zu konfigurieren, die mit den behördlichen Normen ihres Landes konform sind. Der Verwalter des Drahtlosnetzwerks muss die Betriebsbeschränkungen prüfen, die im Zugriffsstellen9Installationshandbuch beschrieben sind. 802.11 사용자 사용자사용자 사용자 주의 : 이 표시는 제품 사용 전에 모든 설명서 내용을 읽어야 한다는 것을 나타냅니다 . 향후 참고를 위해 본 자료를 보관하십시오 . 주의 : Intermec Technologies Corporation 에서 승인한 부속품 및 주변 기기를 사용하는 본 제품의 사용자는 주의를 기울여 야 합니다 . 권장되지 않은 부속품을 사용하거나 Intermec Technologies Corporation 의 승인 없이 본 제품을 변경할 경우 ,본 제품의 보증이 무효화되거나 장비 조작에 대한 사용자의 권한이 박탈될 수 있습니다 . 주의 : 사용자는 해당 국가의 규정 기준을 준수하는 작동 채널 구성에 대한 책임이 있습니다. 무선네크워크 관리자는 액세스포인트 설치 매뉴얼 내에 상세히 기술된 작동 제한규정을 검토해야 합니다 . Usuários do 802,11 Cuidado: Esta identificação indica que o usuário deve ler toda a documentação fornecida antes do uso. Guardeesse suplemento para referências futuras. Cuidado: Os usuários deste produto devem usar acessórios e periféricos aprovados pela Intermec Technologies Corporation. Usar acessórios não recomendados, ou fazer alterações neste produto não aprovadas pela Intermec Technologies Corporation, poderá anular a conformidade deste produto e resultar na perda da permissão do usuário de utilizar o equipamento. Cuidado: Os usuários são responsáveis pela configuração dos canais de funcionamento que atendem aospadrões regulatórios dos seus países. O administrador de rede sem fio deve analisar as restrições operacionais detalhadas no manual de instalação do ponto de acesso. Пользователи оборудования, соответствующего стандарту 802.11 Осторожно: Эта пометка означает, что пользователь должен прочитать всю прилагаемую документацию,прежде чем начинать работу. Сохраните это дополнение для последующих справок. Осторожно: Пользователи этого продукта предупреждаются, что они должны использовать принадлежностии периферийные устройства, утвержденные Intermec Technologies Corporation. Использованиепринадлежностей, не являющихся рекомендованными, или внесение в этот продукт изменений, неутвержденных Intermec Technologies Corporation, может сделать продукт не соответствующим требованиями привести к утрате пользователем права работать с данным оборудованием. Осторожно: Пользователи должны сконфигурировать рабочие каналы в соответствии с регулятивнымистандартами своей страны. Администратор беспроводной сети должен учесть рабочие ограничения, подробно перечисленные в руководстве по установке пункта доступа. Usuarios de 802.11 Precaución: Esta marca indica que el usuario debe leer toda la documentación incluida antes del uso. Retenga este suplemento para referencia futura. Precaución: Se advierte a los usuarios de este producto que usen accesorios y periféricos aprobados por Intermec Technologies Corporation. El uso de accesorios aparte de los recomendados, o los cambios a este producto que no estén aprobados por Intermec Technologies Corporation, pueden anular el cumplimiento de este producto y ocasionar la pérdida de la autorización de…

Text truncated - open the document above for the full version.

Intermec Technologies Corporation 550 Second Street SE Cedar Rapids Iowa 52401-2029 USA Date: 2011-05-3127 General Declaration General Declaration General Declaration General Declaration FCC ID: EHA-RC12BGN We, Intermec Technologies Corporation declares that the device does not have “Ad Hoc on non-US frequencies” . If you have any questions regarding the declaration, please don’t hesitate to contact us. Thank you! Sincerely yours, _____________________________ Kian Meng Lim / Engineer

Date: 2011/04/27 FCC ID: EHA-RC12BGN Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Kian Meng Lim / Engineer Intermec Technologies Corporation 550 Second Street SE Cedar Rapids Iowa 52401-2029 USA

Agency Authorization Letter Date: 2011/04/27 FCC ID: EHA-RC12BGN To whom it may concern: We, the undersigned, hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by BV CPS Taoyuan within the scope of this authorization shall have the same effects as our own. This authorization shall expire six months from the original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Kian Meng Lim / Engineer Intermec Technologies Corporation 550 Second Street SE Cedar Rapids Iowa 52401-2029 USA

Date: December 9, 2010 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 To whom it may concern, Agent’s Authorization Letter I, named contact of grantee for Intermec Technologies Corporation, do hereby authorize, until further notice, Kain Meng Lim of Intermec Technologies, to act on my behalf in dealings before the Federal Communications Commission with respect to all matters relating to equipment authorizations under 47 CFR. This authorization maintains that Intermec Technologies Corporation remains responsible for all statements and exhibits in this application. I certify that no party (as defined in 47 CFR 1.2002) to this application, including myself, is subject to a denial of federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 853A. Certified By: Dave Fry Sr. EMC Engineer Intermec Technologies Corporation Dave Fry MS GR05 550 Second Street Cedar Rapids, IA 52401 Desk tel 319.369.3353 Lab tel 319.846.2415 Fax tel 319.846.2475 [email protected] 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

FCC ID: EHA-RC12BGN Report No.: RF110127C17 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch June 13, 2011 Dear Application Examiner, Intermec Technologies Corporation, It’s an Bluetooth and WLAN Combo Module, FCC ID: EHA-RC12BGN, would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in WL1273. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is WL1251PM. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via an USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was connected with this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: EHA-RC12BGN Report No.: RF110127C17 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Gary Chang Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

Intermec Technologies Corp. 802.11bgn/Bluetooth 2.0 Radio ModuleModel: RC12 P/N: XXX-XXX-XXX IC: 1223A-RC12BGN FCC ID: EHA-RC12BGN FCC LABEL(XXX-XXX-XXX) PLACEMENT REFERENCE ONLY NOT TO SCALE

FCC ID: EHA-RC12BGN IC:1223A-RC12BGN 802.11bgn/Bluetooth 2.0 Radio Module P/N: XXX-XXX-XXX Model: RC12BGN

Page 4 Page 5

FCC ID: EHA-RC12BGN Report No.: RF110127C17 Operational Description This device is a WLAN bgn and Bluetooth Combo Card, which operates in 2.4GHz band. The maximum data rate could be up to 150Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 150Mbps, the 11Mbps data rate with DSSS technique will be applied. For Bluetooth, the data rates are 1/2/3Mbps The transmitter of the EUT is powered by the 5.0Vdc from power adapter. The antenna is Dual Band Dipole antenna with R-TNC antenna connector. For more detailed instruction, please take a look at the user’s manual.

Report No: SA110127C17 R1 1 Report Format Version 4.0.0 Cancels and replaces the report No.: SA110127C17 dated Apr. 26, 2011 RF EXPOSURE REPORT REPORT NO.: SA110127C17 R1 MODEL NO.: RC12BGN FCC ID: EHA-RC12BGN ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Intermec Technologies Corporation ADDRESS: 550 Second street SE Cedar Rapids Iowa 52401-2029 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 5 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval, or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No: SA110127C17 R1 2 Report Format Version 4.0.0 Cancels and replaces the report No.: SA110127C17 dated Apr. 26, 2011 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................. 3 1. CERTIFICATION .......................................................................................................... 4 2. RF EXPOSURE............................................................................................................ 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE)...................................... 5 2.2 MPE CALCULATION FORMULA ................................................................................. 5 2.3 CLASSIFICATION ........................................................................................................ 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER............................... 5 Report No: SA110127C17 R1 3 Report Format Version 4.0.0 Cancels and replaces the report No.: SA110127C17 dated Apr. 26, 2011 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Apr. 26, 2011 SA110127C17 R1 Model name changed. Jun. 21, 2011 Report No: SA110127C17 R1 4 Report Format Version 4.0.0 Cancels and replaces the report No.: SA110127C17 dated Apr. 26, 2011 1. CERTIFICATION PRODUCT: WLAN board MODEL NO.: RC12BGN BRAND: Intermec APPLICANT: Intermec Technologies Corporation TESTED: Feb. 14 ~ Apr. 15, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Guidelines for Human Exposure IEEE C95.1 The above equipment (Model: RC12BGN) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Jun. 21, 2011 Polly Chien / Specialist APPROVED BY : , DATE: Jun. 21, 2011 Gary Chang / Assistant Manager Report No: SA110127C17 R1 5 Report Format Version 4.0.0 Cancels and replaces the report No.: SA110127C17 dated Apr. 26, 2011 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 21.6 2.4 20 0.050 1.00 2402-2480 7.7 2.4 20 0.002 1.00

Report No.: RF110127C17 R1 1 Report Format Version 4.0.0 Cancels and replaces the report No.: RF110127C17 dated Apr. 26, 2011 FCC TEST REPORT (FOR WIRELESS LAN & BLUETOOTH) REPORT NO.: RF110127C17 R1 MODEL NO.: RC12BGN FCC ID: EHA-RC12BGN RECEIVED: Jan. 28, 2011 TESTED: Feb. 14 ~ Apr. 15, 2011 ISSUED: Jun. 21, 2011 APPLICANT: Intermec Technologies Corporation ADDRESS: 550 Second street SE Cedar Rapids Iowa 52401-2029 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 112 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Report No.: RF110127C17 R1 2 Report Format Version 4.0.0 Cancels and replaces the report No.: RF110127C17 dated Apr. 26, 2011 TABLE OF CONTENTS RELEASE CONTROL RECORD.............................................................................................5 1. CERTIFICATION ........................................................................................................6 2. SUMMARY OF TEST RESULTS................................................................................7 2.1 MEASUREMENT UNCERTAINTY .............................................................................8 3. GENERAL INFORMATION ........................................................................................9 3.1 GENERAL DESCRIPTION OF EUT...........................................................................9 3.2 DESCRIPTION OF TEST MODES........................................................................... 11 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST......................................................12 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL...........................13 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ..........................................17 3.4 DESCRIPTION OF SUPPORT UNITS.....................................................................17 4. TEST TYPES AND RESULTS (FOR WIRELESS LAN FUNCTION)........................18 4.1 RADIATED EMISSION MEASUREMENT ................................................................18 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT .............................................18 4.1.2 TEST INSTRUMENTS .............................................................................................19 4.1.3 TEST PROCEDURES ..............................................................................................20 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................20 4.1.5 TEST SETUP ...........................................................................................................21 4.1.6 EUT OPERATING CONDITIONS.............................................................................21 4.1.7 TEST RESULTS .......................................................................................................22 4.2 CONDUCTED EMISSION MEASUREMENT ...........................................................32 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................32 4.2.2 TEST INSTRUMENTS .............................................................................................32 4.2.3 TEST PROCEDURES ..............................................................................................33 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................33 4.2.5 TEST SETUP ...........................................................................................................34 4.2.6 EUT OPERATING CONDITIONS.............................................................................34 4.2.7 TEST RESULTS .......................................................................................................35 4.3 6dB BANDWIDTH MEASUREMENT .......................................................................37 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT.....................................................37 4.3.2 TEST INSTRUMENTS .............................................................................................37 4.3.3 TEST PROCEDURE ................................................................................................37 4.3.4 DEVIATION FROM TEST STANDARD ....................................................................37 4.3.5 TEST SETUP ...........................................................................................................38 4.3.6 EUT OPERATING CONDITIONS.............................................................................38 4.3.7 TEST RESULTS .......................................................................................................39 4.4 MAXIMUM OUTPUT POWER..................................................................................42 4.4.1 LIMITS OF MAXIMUM OUTPUT POWER MEASUREMENT ..................................42 4.4.2 INSTRUMENTS .......................................................................................................42 4.4.3 TEST PROCEDURES ..............................................................................................42 4.4.4 DEVIATION FROM TEST STANDARD ....................................................................42 4.4.5 TEST SETUP ...........................................................................................................43 Report No.: RF110127C17 R1 3 Report Form…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4