EHA-RW10RW10

Northwest EMC TCB Compliance Opinion Rev. 12/08/09 INMC0656 Information about the Applicant Grantee (Company Name) Intermec Technologies Corporation FCC Contact Person Dave Fry Address 6001 36th Avenue West City, State, Zip Everett, WA 98203-1264 Job Number INMC0656 Model RW10 FCC ID EHA-RW10 Agent Wayne Rieger, Yogendra Shah Approval Type Original Equipment Class PCB – PCS Licensed Transmitter Rule Part 22H, 24E Overview This application is for an original filing of Intermec's UMTS radio module model RW10. The RW10 is identical to the Sierra Wireless model MC8795V manufactured by Flextronix, which is the subject of the CTTL report referenced in this application.. Confidentiality requested for allowed files. Request is properly addressed and referenced. A letter listing the applicable modular requirements was submitted. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature Dave Tolman, TCB Committee 3/8/2011

1 March 2011 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Subject: Original Application FCC ID: EHA-RW10 Dear Application Examiner: Intermec Technologies Corporation is submitting this application for certification of their Model RW10, FCC ID: EHA-RW10. The device is a UMTS radio module. Authorization is sought under FCC Parts 22H and 24E. The device will only be used 20 cm or greater from the user’s head or torso so MPE estimates were performed. The following EMC reports have been submitted as part of this application: • NWEMC Test Report # INMC0656: ERP, EIRP, and Spurious Radiated Emissions • CTTL Test Report # I09GW 6944-FCC-EMC, plus supplement report: All antenna port direct connect measurements Note that some of the exhibits refer to the Flextronics or Sierra MC8795V. These radios are electrically and mechanically identical to the Intermec Model RW10, FCC ID: EHA-RW10. The antenna port direct connect data contained in the CTTL report is representative of the subject device, FCC ID: EHA-RW10. FCC Verification testing of the receiver portion of the device has also been performed. Your efforts in reviewing this application are greatly appreciated. Sincerely, Wayne F. Rieger Radio Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

March 1, 2011 Subject: Modular Approval FCC ID: EHA-RW10 Dear Application Examiner: Intermec Technologies Corporation is submitting an application for certification of the Model RW10 radio, FCC ID: EHA-RW10. It is a UMTS radio module. Modular approval is sought under FCC 22H and 24E. The radio meets the requirements for modular approval as detailed in FCC 15.212. Compliance to each of the requirements is described below: 1. “The modular transmitter must have its own RF shielding.” The radio portion of the module is contained in its own RF shielding. The shielding is installed at the factory. Please see the External Photos exhibit. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs to insure compliance with Part 15 requirements under conditions of excessive data rates or over-modulation. Please see the Schematics exhibit. 3. “The modular transmitter must have its own power supply regulation.” The EUT has its own power supply regulation to insure compliance with FCC requirements regardless of the quality or level of external DC supplying the module from the host unit. Please see Schematics exhibit. 4. “The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c).” The EUT meets the FCC antenna requirements. Please see Antenna information exhibit and internal photos exhibit. 5. “The modular transmitter must be tested in a stand-alone configuration.” The EUT was tested in a stand-alone configuration. The module was greater than 10 cm from the host device. Please see test setup photos exhibit and technical report exhibit. 6. “The modular transmitter must be labeled with its own FCC ID number.” The EUT is labeled with its own FCC ID number. Please see FCC ID label & location exhibit. Since the FCC ID number will not be visible when the module is installed inside a host device, another label with the FCC ID will be applied to the exterior of the host device. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the User Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. Please see RF Exposure Exhibit. Please contact me if you have additional questions. Your attention to this matter is greatly appreciated. 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com Best regards, Wayne F. Rieger Radio Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203-1264 425-267-2919

Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: EHA-RW10 To Whom It May Concern: Our radio vendor, Sierra Wireless, has requested long-term confidentiality for the following exhibits under a separate letter attached to this application: Schematic Diagrams Block Diagram Operational Description Tune-up Procedure It is our understanding that all measurement test reports, FCC ID label format and correspondent during the certification review process cannot be granted as confidential documents and that information will be available for public review once the grant of equipment authorization is issued. Best regards, Wayne F. Rieger Radio Compliance Engineer Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203-1264 425-267-2919 6001 36 th Avenue West Everett, Washington 98203 United States tel 425.348.2600 fax 425.355.9551 www.intermec.com

September 30, 2010 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern, Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential documents from public disclosure indefinitely.  Schematics  Theory of Operation  Frequency Block Diagrams  Tune-up Procedure Any exhibit / information for which we have requested confidentiality, but which may not be accorded such treatment by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Sincerely, Todd Van Cleave Manager Engineering Services Carlsbad Research & Development Sierra Wireless America, Inc.

External Photos Picture 1: the front view of the sample Picture 2: the back view of the sample

PRE-RELEASE PRE-RELEASE

Internal Photos Picture 1: the front view of the sample without shielding cover Picture 2: the back view of the sample without shielding cover

Intermec Radio Group Antenna Measurement System Manufacturer: Laird Technologies Model No: 805-668-001 Serial No: WAN RF Test Fixture Operator: Paul Hulett Comment: NA Main WWAN Test Method: Two-Axis Dual-Polarization Pattern Measurement Type: PIFA Date: 11/10/2110 Summary Page Total Frequency (MHz) 780 800 824 850 869 894 Peak Gain (dBi) -3.53162 -2.20285 -0.484213 0.295376 0.195954 -0.464057 Average Gain (dBi) -6.44448 -5.32961 -3.81917 -3.20924 -3.29624 -3.9979 Average Gain (dBi) -6.44448 -5.32961 -3.81917 -3.20924 -3.29624 -3.9979 Total Frequency (MHz) 915 960 980 1574 1575 1576 Peak Gain (dBi) -1.72232 -4.95514 -6.21709 -2.18289 -2.14646 -2.09221 Average Gain (dBi) -5.4554 -9.05365 -10.4916 -6.36393 -6.38103 -6.33692 Total Frequency (MHz) 1695 1710 1750 1800 1850 1880 Peak Gain (dBi) 3.38486 2.38805 1.95986 1.93766 2.28455 2.06766 Average Gain (dBi) -1.5775 -1.84597 -2.85863 -2.4196 -1.73968 -1.01097 Total Frequency (MHz) 1900 1920 1930 1960 1990 2110 Peak Gain (dBi) 2.71454 2.30739 2.81846 3.01201 3.34611 1.67473 Average Gain (dBi) -0.625208 -0.247921 0.191235 0.256497 -0.270234 -2.90073 Total Frequency (MHz) 2160 2170 2190 2200 Peak Gain (dBi) 1.24144 2.36 2.22694 3.09822 Average Gain (dBi) -2.38225 -2.39256 -2.60534 -2.66813 WAN Free-Space Total EIRP, 780 MHz Total EIRP, Right Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elevation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azimuth = 0.0 Elev ation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elev ation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Y Z Azimuth = 0.0 Elevation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Y Z X Azimuth = 90.0 Elevation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 XY Z Azimuth = -90.0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 800 MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azimuth = 0.0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Y Z Azimuth = 0.0 Elev ation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Y Z X Azimuth = 90.0 Elev ation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 XY Z Azi muth = -9 0. 0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 824 MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azi muth = 0 . 0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Y Z Azimuth = 0.0 Elev ation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Y Z X Azimuth = 90.0 Elev ation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 XY Z Azimuth = -90.0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 850MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 YX Z Azimuth = 0.0 Elevation = 90.0 Roll = 0.0 Tot a l EIRP, Bot t om Vie w EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Y Z Azimuth = 0.0 Elev ation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 Y Z X Azimuth = 90.0 Elev ation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Z Y Azimuth = -90.0 Elevation = 1.0 Roll = 92.0 WAN Free-Space Total EIRP, 869MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Z Y Azimuth = 90.0 Elevation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 YX Z Azimuth = 0.0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 Z X Y Azimuth = -180.0 Elev ation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 X Y Z Azimuth = 0.0 Elevation = 0.0 Roll = 0.0 Tot a l EI RP , Fr ont Fa c e V i e w EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 Y Z X Azimuth = 90.0 Elevation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 5 -25 -20 -15 -10 -5 0 XY Z Azimuth = -90.0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 894MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azi muth = 0 . 0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Y Z Azimuth = 0.0 Elev ation = 0.0 Roll = 0.0 Total EIRP, Front Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z Y X Azimuth = 90.0 Elev ation = 0.0 Roll = -90.0 Total EIRP, Back Face View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 XY Z Azimuth = -90.0 Elev ation = 0.0 Roll = 90.0 WAN Free-Space Total EIRP, 915MHz Tot a l EIRP, Right Side Vie w EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X Z Y Azimuth = 90.0 Elev ation = -90.0 Roll = -90.0 Total EIRP, Left Side View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 YX Z Azimuth = 0.0 Elevation = 90.0 Roll = 0.0 Total EIRP, Bottom View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 Z X Y Azimuth = -180.0 Elevation = -1.0 Roll = -179.0 Total EIRP, Top View EIRP (dBm) -30 0 -25 -20 -15 -10 -5 X…

Text truncated - open the document above for the full version.

Antenna Type Antenna Manuf acturer Ant enna Part No. Transmit Frequen cy Ma x Pea k Conducted Ou tput Power Antenna Gain Mi ni mum Ant enna Cable Loss Power Density @ 20 cm General Pop ula ti on Exposu re Limit from 1.1310 (MHz)( mW)(d Bi)( dB)(mW/cm 2 )(mW/cm 2 ) PIFALaird Laird WLAN82415780.300.340.55 PI FALa irdL ai rd WL AN18 5099 52. 700. 3 71 FCC ID: EHA-RW10 Compliance with 47 CFR 2.1091 and 1.1310 The EUT is a UMTS radio module. The EUT will only be used with a separation distance of 20 centimeters or greater between the antenna and the body of the user or nearby persons and can therefore be considered a mobile transmitter per 47 CFR 2.1091(b). The antenna is a PIFA with a peak gain of 0.3 dBi in the 824 MHz band and 2.7 in the 1850 MHz band. The maximum peak conducted output power is 1578mW in the 824 MHz band, and 995 mW in the 1850 MHz band. The maximum peak radiated power (as measured in the EMC report) is 0.698 W (ERP) in the 824 MHz band and 0.427 W (ERP) in the 1850 MHz band. Since the radiated power is less than 1.5 W ERP, the EUT is categorically excluded from routine environmental evaluation per 47 CFR 2.1091(c). The MPE estimates are as follows: Table 1 in 47 CFR 1.1310 defines the maximum permissible exposure (MPE) for the general population below 1500 MHz as f/1500 mW/cm 2 where f = MHz. Above 1500 MHz, the limit is 1 mW/cm 2 . The exposure level at a 20 cm distance from the EUT’s transmitting antenna is calculated using the general equation: S = (PG)/4R 2 Where: S = power density (mW/cm 2 ) P = power input to the antenna (mW) G = numeric power gain relative to an isotropic radiator R = distance to the center of the radiation of the antenna (20 cm = limit for MPE estimates) PG = EIRP Solving for S, the maximum power density 20 cm from the transmitting antenna is summarized in the following table: The power density does not exceed 0.37 mW/cm 2 at 20 cm; therefore, the exposure condition is compliant with FCC rules.

FCC Parts 2, 22, 24 Equipment: MC8795V REPORT NO.: I09GW6944-FCC-EMC-3 Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 2 of 69 China Telecommunication Technology Labs. ® FCC ID: N7NMC8795 Report Date: 2010-4-13 Test Firm Name: China Telecommunication Technology Labs Registration Number: 840587 Statement The measurements shown in this report were made in accordance with the procedures described on test pages. All reported tests were carried out on a sample equipment to demonstrate limited compliance with FCC CFR 47 Parts 2, 22, and 24. The sample tested was found to comply with the requirements defined in the applied rules. FCC Parts 2, 22, 24 Equipment: MC8795V REPORT NO.: I09GW6944-FCC-EMC-3 Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 3 of 69 China Telecommunication Technology Labs. ® CONTENTS 1 GENERAL INFORMATION .......................................................................4 1.1 NOTES...............................................................................................4 1.2 TESTERS.............................................................................................5 1.3 TESTING LABORATORY INFORMATION............................................................7 1.4 DETAILS OF APPLICANT OR MANUFACTURER.....................................................8 2 TEST ITEM .............................................................................................9 2.1 GENERAL INFORMATION...........................................................................9 2.2 OUTLINE OF EUT...................................................................................9 2.3 MODIFICATIONS INCORPORATED IN EUT ........................................................9 2.4 EQUIPMENT CONFIGURATION.....................................................................9 2.5 OTHER INFORMATION............................................................................ 10 3 SUMMARY OF TEST RESULTS ............................................................... 11 4 TEST RESULTS OF MODE ...................................................................... 13 4.1 RADIATED SPURIOUS EMISSION................................................................ 13 4.2 RADIATED RF POWER OUTPUT AND ERP ...................................................... 27 4.3 OCCUPIED BANDWIDTH.......................................................................... 30 4.4 FREQUENCY STABILITY OVER TEMPERATURE VARIATION..................................... 42 4.5 FREQUENCY STABILITY OVER VOLTAGE VARIATION........................................... 46 4.6 CONDUCTED RF POWER OUTPUT............................................................... 48 4.7 CONDUCTED SPURIOUS EMISSION............................................................. 52 4.8 BAND EDGE....................................................................................... 57 ANNEX A EXTERNAL PHOTOS ................................................................. 65 ANNEX B INTERNAL PHOTOS.................................................................. 66 ANNEX C DEVIATIONS FROM PRESCRIBED TEST METHODS.................... 69 FCC Parts 2, 22, 24 Equipment: MC8795V REPORT NO.: I09GW6944-FCC-EMC-3 Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 4 of 69 China Telecommunication Technology Labs. ® 1 General Information 1.1 Notes All reported tests were carried out on a sample equipment to demonstrate limited compliance with FCC CFR 47 Parts 2, 22 and 24. The test results of this test report relate exclusively to the item(s) tested as specified in section 2. The following deviation from, additions to, or exclusions from the test specifications have been made. See Annex C. China Telecommunication Technology Labs.(CTTL) authorizes the applicant or manufacturer (see section 1.4) to reproduce this report provided, and the test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of CTTL Mr. He Guili. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. CTTL accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. FCC Parts 2, 22, 24 Equipment: MC8795V REPORT NO.: I09GW6944-FCC-EMC-3 Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 6 of 69 China Telecommunication Technology Labs. ® Technical responsibility for area of testing: Name: Zou Dongyi Position: Manager Department: Department of EMC test Date: 2010-4-13 Signature: FCC Parts 2, 22, 24 Equipment: MC8795V REPORT NO.: I09GW6944-FCC-EMC-3 Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 7 of 69 China Telecommunication Technology Labs. ® 1.3 Testing Laboratory information 1.3.1 Location Name: China Telecommunication Technology Labs. Address: No. 11, Yue Tan Nan Jie, Xi Cheng District BEIJING P. R. CHINA, 100045 Tel: +86 10 68094053 Fax: +86 10 68011404 Email: [email protected] 1.3.2 Details of accreditation status Accredited by: China National Accreditation Service for Conformity Assessment (CNAS) Registration number: CNAS Registration No. CNAS L0570 Standard: ISO/IEC 17025:2005 1.3.3 Test location, where different from section 1.3.1 Name: ------ Street: ------ City: ------ Country: ------ Telephone: ------ Fax: ------ Postcode: ------ FCC Parts 2, 22, 24 Equipment: MC8795V REPORT NO.: I09GW6944-FCC-EMC-3 Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 8 of 69 China Telecommunication Technolo…

Text truncated - open the document above for the full version.

Intermec Technologies Corporation Model: RW10 Tested to the following Specifications: FCC 22H:2010 FCC 24E:2010 Report No. INMC0656 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2011 Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: January 7, 2011 Intermec Technologies Corporation Model: RW10 Emissions Test Description Specification Test Method Pass/Fail Out of Band Emissions FCC 22H:2011 ANSI/TIA/EIA-603-C-2004 Pass Out of Band Emissions FCC 24E:2011 ANSI/TIA/EIA-603-C-2004 Pass Effective Radiated Power (ERP) FCC 22H:2011 ANSI/TIA/EIA-603-C-2004 Pass Effective Radiated Power (EIRP) FCC 24E:2011 ANSI/TIA/EIA-603-C-2004 Pass Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834D-2). Approved By: Tim O'Shea, Operations Manager NVLAP Lab Code: 200630-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 06/29/09 Barometric Pressure The recorded barometric pressure has been normalized to sea level. Revision Number Description Date Page Number 00 None Accreditations and Authorizations FCC Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP Northwest EMC, Inc. is accredited under the National Voluntary Laboratory Accreditation Program (NVLAP) for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. NVLAP is administered by the National Institute of Standards and Technology (NIST), an agency of the U.S. Commerce Department. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 2004/108/EC, and ANSI C63.4. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. Industry Canada Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS-Gen, Issue 2 and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by NIST and recognized by Industry Canada as a Certification Body (CB) per the APEC Mutual Recognition Arrangement (MRA). This allows Northwest EMC to certify transmitters to Industry Canada technical requirements. (Site Filing Numbers - Hillsboro: 2834D-1, 2834D-2, Sultan: 2834C-1, Irvine: 2834B-1, 2834B-2, Brooklyn Park: 2834E-1) CAB Designated by NIST and validated by the European Commission as a Conformity Assessment Body (CAB) to conduct tests and approve products to the EMC directive and transmitters to the R&TTE directive, as described in the U.S. - EU Mutual Recognition Agreement. Australia/New Zealand The National Association of Testing Authorities (NATA), Australia has been appointed by the ACA as an accreditation body to accredit test laboratories and competent bodies for EMC standards. Accredited test reports or assessments by competent bodies must carry the NATA logo. Test reports made by an overseas laboratory that has been accredited for the relevant standards by an overseas accreditation body that has a Mutual Recognition Agreement (MRA) with NATA are also accepted as technical grounds for product conformity. The report should be endorsed with the respective logo of the accreditation body (NVLAP). Accreditations and Authorizations VCCI Accepted as an Associate Member to the VCCI, Acceptance No. 564. Conducted and radiated measurement facilities have been registered in accordance with Regulations for Voluntary Control Measures, Article 8. (Registration Numbers. - Hillsboro: C-1071, R-1025, G-84, C-2687, T- 1658, and R-2318, Irvine: R-1943, G-85, C-2766, and T-1659, Sultan: R-871, G-83, C-1784, and T-1511, Brooklyn Park: R-3125, G-86, G-141, C-3464, and T-1634). BSMI Northwest EMC has been designated by NIST and validated by C-Taipei (BSMI) as a CAB to conduct tests as described in the APEC Mutual Recognition Agreement (US0017). GOST Northwest EMC, Inc. has been assessed and accredited by the Russian Certification bodies Certinform VNIINMASH, CERTINFO, SAMTES, and Federal CHEC, to perform EMC and Hygienic testing for Information Technology Products. As a result of their laboratory assessment, they will accept test results from Northwest EMC, Inc. for product certification KCC Northwest EMC, Inc is a CAB designated by MRA partners and recognized by Korea. (Assigned Lab Numbers: Hillsboro: US00…

Text truncated - open the document above for the full version.

FCC Parts 2, 22, 24 Equipment: MC8795V Supplement to Test Report I09GW6944-FCC-EMC-3 Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 2 of 54 China Telecommunication Technology Labs. ® FCC ID: N7NMC8795 Report Date: 2010-4-13 Test Firm Name: China Telecommunication Technology Labs Registration Number: 840587 Statement The measurements shown in this report were made in accordance with the procedures described on test pages. All reported tests were carried out on a sample equipment to demonstrate limited compliance with FCC CFR 47 Parts 2, 22, and 24. The sample tested was found to comply with the requirements defined in the applied rules. FCC Parts 2, 22, 24 Equipment: MC8795V Supplement to Test Report I09GW6944-FCC-EMC-3 Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 3 of 54 China Telecommunication Technology Labs. ® CONTENTS 1 GENERAL INFORMATION .......................................................................4 1.1 NOTES...............................................................................................4 1.2 TESTERS.............................................................................................5 1.3 TESTING LABORATORY INFORMATION............................................................6 1.4 DETAILS OF APPLICANT OR MANUFACTURER.....................................................7 2 TEST ITEM .............................................................................................8 2.1 GENERAL INFORMATION...........................................................................8 2.2 OUTLINE OF EUT...................................................................................8 2.3 MODIFICATIONS INCORPORATED IN EUT ........................................................8 2.4 EQUIPMENT CONFIGURATION.....................................................................8 2.5 OTHER INFORMATION..............................................................................9 3 SUMMARY OF TEST RESULTS ............................................................... 10 4 TEST RESULTS OF MODE ...................................................................... 11 4.1 RADIATED SPURIOUS EMISSION................................................................ 11 4.2 RADIATED RF POWER OUTPUT AND ERP ...................................................... 21 4.3 OCCUPIED BANDWIDTH......................................................…

Text truncated - open the document above for the full version.