EHARFID915PCC-6RF IDENTIFICATION PC CARD

Intermec Technologies CorporationREPORT NO: 010416-1 EMC Test LaboratoryDATE: April 16, 2001 DOC. NO.: 577-500-980Page 1 of 1 915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102FCC ID: EHARFID915PCC-6 APPENDIX L, 915 PC Card-6 Users Manual and DoC insert Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation RF Identification (RFID) 915 PC Card –6 915 MHz Spread Spectrum Transmitter REPORT NO: 010416-1 DATE: April 16, 2001 APPENDIX L DECLARATION OF CONFORMITY INSERT, USER INFORMATION FOR THE 915 PC CARD 578-100-0xx Revision APage 1 of 1 *578-100-0xx* *578-100-0xx* Compliance Statement Insert Device Name: RF Identification Radio ModuleModel Number: 2450 PC Card -5 The responsible party for the compliance of this device is:Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203 USA (425) 348-2600 This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: RFID 915 PC Card Warning: per the FCC and Canadian RF (radio frequency) exposure requirements, 1. Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to RF exposure requirements. Intermec antenna part number(s) 805-589-001, 805-590-001 and 805-591-001. Correct antenna mounting is fully described within the Intermec RFID 915 PC Card Users Guide. 2. When installing and using Intermec approved remote antennas associated the RFID reader, a 4-cm (1.5-inch) passing distance must be maintained from any body part of the user or near by persons and the remote antenna. The antenna must not be touched during transmitter operation. 3. Cables attached to the remote antennas must have a minimum length as provided from Intermec to insure the proper losses to control RF exposure.

Intermec Technologies CorporationREPORT NO: 010416-1 EMC Test LaboratoryDATE: April 16, 2001 DOC. NO.: 577-500-980Page 1 of 1 915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102FCC ID: EHARFID915PCC-6 APPENDIX M, 6110 Users Manual and DoC insert Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation RF Identification (RFID) 915 PC Card –6 915 MHz Spread Spectrum Transmitter REPORT NO: 010416-1 DATE: April 16, 2001 APPENDIX M DECLARATION OF CONFORMITY INSERT, USER INFORMATION FOR THE INTERMEC 6110 TERMINAL 578-100-0xx Revision APage 1 of 1 *578-100-0xx* *578-100-0xx* Compliance Statement Insert Device Name: Hand-held ComputerModel Number: 6110 The responsible party for the compliance of this device is:Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203 USA (425) 348-2600 This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in personal injury, fire, or battery explosion. INTERMEC RFID 915 PC Card Radio Users FCC ID: EHARFID915PCC-6 WARNING: per the FCC RF (radio frequency) exposure requirements, (1) Only the antenna supplied and installed with this unit by Intermec Technologies is to be used with this hand held terminal. The product is configured to ensure compliance to FCC RF exposure requirements. (2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna while the transmitter is in use. INTERMEC RFID 915 PC Card Radio Users Canada ID: xxxxxxxxxx WARNING: per Canada RSS-102, RF (radio frequency) exposure requirements, (1) Only the antenna supplied and installed with this unit by Intermec Technologies is to be used with this hand held terminal. The product is configured to ensure compliance to Canada RF exposure requirements. (2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna while the transmitter is in use.

Intermec Technologies CorporationREPORT NO: 010416-1 EMC Test LaboratoryDATE: April 16, 2001 DOC. NO.: 577-500-980 Page 1 of 2 915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102FCC ID: EHARFID915PCC-6 APPENDIX L, 915 PC Card-6 Users Manual and DoC insert, Rev B Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation RF Identification (RFID) 915 PC Card –6 915 MHz Spread Spectrum Transmitter REPORT NO: 010416-1 DATE: April 16, 2001 APPENDIX L DECLARATION OF CONFORMITY INSERT, USER INFORMATION FOR THE 915 PC CARD 578-100-0xx Revision APage 1 of 1 *578-100-0xx* *578-100-0xx* Compliance Statement Insert Device Name: RF Identification Radio ModuleModel Number: 2450 PC Card -5 The responsible party for the compliance of this device is:Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203 USA (425) 348-2600 This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: RFID 915 PC Card Warning: per the FCC and Canadian RF (radio frequency) exposure requirements, 1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to RF exposure requirements. Intermec antenna part number(s) 805-589-001, 805-590-001 and 805-591-001. Correct antenna mounting is fully described within the Intermec RFID 915 PC Card Users Guide. 2) When installing and using Intermec approved remote antennas associated the RFID reader, a 4-cm (1.5-inch) passing distance must be maintained from any body part of the user or near by persons and the remote antenna. The antenna must not be touched during transmitter operation. 3) Cables attached to the remote antennas must have a minimum length as provided from Intermec to insure the proper losses to control RF exposure. 4) RF safety requirements mandate this device cannot be operated in close proximity to other transmitters.

Intermec Technologies CorporationREPORT NO: 010416-1 EMC Test LaboratoryDATE: April 16, 2001 DOC. NO.: 577-500-980 Page 1 of 2 915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102FCC ID: EHARFID915PCC-6 APPENDIX M, 6110 Users Manual and DoC insert, Rev B Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation RF Identification (RFID) 915 PC Card –6 915 MHz Spread Spectrum Transmitter REPORT NO: 010416-1 DATE: April 16, 2001 APPENDIX M DECLARATION OF CONFORMITY INSERT, USER INFORMATION FOR THE INTERMEC 6110 TERMINAL 578-100-0xx Revision APage 1 of 1 *578-100-0xx* *578-100-0xx* Compliance Statement Insert Device Name: Hand-held ComputerModel Number: 6110 The responsible party for the compliance of this device is:Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203 USA (425) 348-2600 This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in personal injury, fire, or battery explosion. INTERMEC RFID 915 PC Card Radio Users FCC ID: EHARFID915PCC-6 Canada ID: xxxxxxxxxx WARNING: per the FCC and Canada RSS-102, RF (radio frequency) exposure requirements, (1) Only the antenna supplied and installed with this unit by Intermec Technologies is to be used with this hand held terminal. The product is configured to ensure compliance to RF exposure requirements. (2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna while the transmitter is in use. (3) RF safety requirements mandate this device cannot be operated in close proximity to other transmitters.

Intermec Technologies CorporationREPORT NO: 010416-1 EMC Test LaboratoryDATE: April 16, 2001 DOC. NO.: 577-500-980 Page 1 of 2 915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102FCC ID: EHARFID915PCC-6 APPENDIX L, Rev C, 915 PC Card-6 Users Manual and DoC insert Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation RF Identification (RFID) 915 PC Card –6 915 MHz Spread Spectrum Transmitter REPORT NO: 010416-1 DATE: April 16, 2001 APPENDIX L DECLARATION OF CONFORMITY INSERT, USER INFORMATION FOR THE 915 PC CARD 578-100-0xx Revision CPage 1 of 1 *578-100-0xx* *578-100-0xx* Compliance Statement Insert Device Name: RF Identification Radio ModuleModel Number: 915 PC Card –5 FCC ID: EHARFID915PCC-5 The responsible party for the compliance of this device is:Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203 USA (425) 348-2600 This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: RFID 915 PC Card Warning: per the FCC and Canadian RF (radio frequency) exposure requirements, 1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to RF exposure requirements. Intermec antenna part number(s) 805-589-001, 805-590-001 and 805-591-001. Correct antenna mounting is fully described within the Intermec RFID 915 PC Card Users Guide. 2) When installing and using Intermec approved remote antennas associated the RFID reader, a 4-cm (1.5-inch) passing distance must be maintained from any body part of the user or near by persons and the remote antenna. The antenna must not be touched during transmitter operation. 3) Cables attached to the remote antennas must have a minimum length as provided from Intermec to insure the proper losses to control RF exposure. 4) RF safety requirements mandate this device cannot be co-located with other transmitters.

Intermec Technologies CorporationREPORT NO: 010416-1 EMC Test LaboratoryDATE: April 16, 2001 DOC. NO.: 577-500-980 Page 1 of 2 915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102FCC ID: EHARFID915PCC-6 APPENDIX M, Rev C, 6110 Users Manual and DoC insert Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation RF Identification (RFID) 915 PC Card –6 915 MHz Spread Spectrum Transmitter REPORT NO: 010416-1 DATE: April 16, 2001 APPENDIX M DECLARATION OF CONFORMITY INSERT, USER INFORMATION FOR THE INTERMEC 6110 TERMINAL 578-100-0xx Revision CPage 1 of 1 *578-100-0xx* *578-100-0xx* Compliance Statement Insert Device Name: Hand-held ComputerModel Number: 6110 The responsible party for the compliance of this device is:Intermec Technologies Corporation 6001 36 th Avenue West Everett, WA 98203 USA (425) 348-2600 This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in personal injury, fire, or battery explosion. INTERMEC RFID 915 PC Card Radio Users FCC ID: EHARFID915PCC-6 Canada ID: xxxxxxxxxx WARNING: per the FCC and Canada RSS-102, RF (radio frequency) exposure requirements, (1) Only the antenna supplied and installed with this unit by Intermec Technologies is to be used with this hand held terminal. The product is configured to ensure compliance to RF exposure requirements. (2) The user shall not touch the terminal top (antenna) and is to remain 5-cm (2 of and inches) from the front of the antenna while the transmitter is in use. (3) RF safety requirements mandate this device cannot be co-located with other transmitters.

A Company July 2, 2001 Intermec Technologies Corporation Systems and Solutions 550 Second Street S.E. Cedar Rapids, IA 52401 CONFIDENTIALITY REQUEST CONTAINED WITHIN Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: Application of Modular Approval for Frequency Hopping Spread Spectrum (FHSS) Transceiver Certification FCC ID: EHARFID915PCC-6 Gentlemen Application: Intermec Technologies Corporation, 550 Second Street SE, Cedar Rapids, Iowa 52401-2029 herein submits: Application for Equipment Authorization (FCC Form 731 with integrated Fee Processing Form, Fee Codes EGC and EBC), application fee in the amount of $1130 and Exhibits; for Certification of a Frequency Hopping Spread Spectrum Transceiver FCC ID: EHARFID915PCC-6. Intermec is also the manufacturer of this equipment. Confidentiality: Pursuant to Section 0.459 of the Commission's rules (CFR 47), Intermec requests confidentiality for portions of the material contained in this application and that the identified material be withheld from public inspection following the grant of this authorization. This material contains Intermec trade secrets and confidential information that Intermec does not customarily release to the public and which is otherwise not generally available to the pubic. Confidentiality is requested for the following exhibits: • Appendix I Theory of Operation • Appendix J Block Diagram • Appendix K Schematics and Parts Placement Description: This equipment is a FHSS radio module, which operates in the 902-928 MHz band. It can interrogate and write to RFID tags operating in the same frequency band. Modular approval is requested since the PCMCIA design allows use in multiple hosts of various configurations. Statements addressing conditions for modular approval are contained within the main body of the test report. Contact Information: Please contact me by telephone at (319) 846-2415 or by e-mail ([email protected]) if there are questions or additional information needed concerning this filing. Yours truly, Dave Fry, Regulatory Engineer II Intermec Technologies Corporation EMC Test Laboratory

To:Steve Dayhoff From:Dave Fry, null [email protected] Regulatory Engineer Re:FCC ID EHARFID915PCC-6 Applicant:Intermec Technologies Corporation Correspondence Reference Number:20557 731 Confirmation Number:EA101560 1. Please explain how the system complies with Section 15.247(g), when presented with a continuous data stream, or a short transmission burst. Please review page 5 of the Theory of Operation under Hopping Sequence Generation. Also the system is designed to only remain on channel for a maximum of 50milliseconds. 2. Frequency Hopping spread spectrum systems "FHSS" must meet the definition in Section 2.1 and commonly operate in Section 15.247. The definition among other things requires that the carrier is modulated with coded information. For tag readers, information from the reader must be sent to the tag and "written" to the tag. We have turned down systems that just sends a CW signal or (no information) to the systems tag. One system we have accepted in the past is one which the downlink transmitter is a single transmitter and the data signal and powering signal are duplexed by time division. The signals occur on the same frequency and occur within the 400 msec limit before the device hops to the next frequency in the pseudorandom sequence. The tab must be passive from an RF standpoint(powered only by the downlink signal) and is considered simply a part of the transmission path. The bandwidth of the uplink receiver must match the occupied bandwidth of the data modulated downlink signal, and the uplink recevier must be hopped in synchronization with the downlink transmitter. The system transmits information in both directions. Data can be written to the tag and can be read from the tag. In light of the above, describe your system with regard to how it meets the definition of a FHSS system. Describe the data and power signals. Does the device send a CW signal? A revised Theory of Operation has been sent to the FCC EAS system. Please review the second paragraph on page 2 under “Introduction”. 3. With regard to RF safety, the warning statements must include that the device cannot be used with other co-located transmitters. Please see the revised users information pages Appendix L and M. The added statement, “RF safety requirements mandate this device cannot be operated in close proximity to other transmitters.”, should address this requirement. 4. Only the 6110 hand-held terminal can be approved. Future hand-held terminals will require a Class II Permissive Change application with new RF Safety evaluations, since the safe distances might change with each new mechanical design. It is unfortunate the FCC has taken this stand. Burdens for approvals on essentially identical antennas for use in hand held terminals would cost thousands with only millimeters of changes in compliance distances. Retesting and measurement uncertainties related to SAR testing will introduce greater differences in SAR than implementing these same antennas in products operated in the hand. Considering the safety requirements for Canada and Europe are under Self-Declaration, the FCC needs to reconsider their policies. For additional hand held terminals to use the antennas approved for the 6110 Intermec will repeat SAR testing and submit Class II Permissive changes as stated above. The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 60 days of the original e-mail date may result in application dismissal pursuant to Section 2.917 (c) and forfeiture of the filing fee pursuant to section 1.1108. DO NOT reply to this e-mail by using the Reply button. In order for your response to be processed expeditiously, you must upload your response via the Internet at www.fcc.gov, Electronic Filing, OET Equipment Authorization Electronic Filing. If the response is submitted through Add Attachments, in order to ex…

Text truncated - open the document above for the full version.