EHAWANRIM802WLAN Radio Module

Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 1 of 3 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix E, Declaration of Conformity Insert Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 802 REPORT NO: 20010120-1 DATE: January 20, 2001 APPENDIX E DECLARATION OF CONFORMITY INSERT, USER INFORMATION Note: Other mobile radio users will have a compliance statement similar to the 6620 statement enclosed. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 2 of 3 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix E, Declaration of Conformity Insert Compliance Statement Insert Device Name: Hand-held ComputerModel Number: 6110 The responsible party for the compliance of this device is:Intermec Technologies Corporation Norand Mobile System Division 550 Second Street SE Cedar Rapids, Iowa 52401 USA (319) 369-3100 CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in personal injury, fire, or battery explosion. This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may expose hazards to the operator or nearby persons, void the compliance of this product and may result in the loss of the users authority to operate the equipment. RIM 802 ARDIS Radio Users FCC ID: EHAWANRIM802 WARNING: per the FCC RF (radio frequency) exposure requirements, (1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF exposure requirements. (2) The user shall not touch the terminal antenna and is to remain 15-mm (5/8 of and inch) from the center of the antenna while the transceiver is in use. (3) When installing and using Intermec approved remote antennas associated the vehicle dock, a 20-cm (8-inch) passing distance must be maintained from any body part of the user or near by persons and the remote antenna. (4) Cables attached to the remote antennas must have a minimum length of 183-cm (6 feet) to provide the proper losses to control RF exposure. (5) The correct mounting for external or remote antennas would be on a ground plane (vehicle roof), and positioning the antenna such that the minimum 20 cm is kept from any edge of the vehicle rooftop and the remote antenna. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Telephone Installation Warning Notices The following notices apply to equipment that may be connected to telephone lines or systems. For your personal safety, and to protect this equipment from potential electrical or physical damage, do NOT connect equipment to telephone lines or data communication equipment unless the following warnings have been read, understood, and complied with. • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. • Avoid using telephone (other than cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. • Do not use the telephone to report a gas leak in the vicinity of the leak. Installation do téléphone : avertissements Les avertissements qui suivent s'appliquent à tout équipement qui peut être branché aux lignes ou systemes téléphoniques. Pour votre sécurité personnelle et pour protéger l'équipement de tout dommage électrique ou physique potentiel, NE PAS brancher un ordinateur tablette électronique ou ses périphériques aux lignes téléphoniques ou équipements avant que les avertissements suivants aient été lus, compris et observés: • Ne jamais installer de câblage téléphonique pendant un orage électrique. • Ne jamais installer de prise téléphonique dans un endroit humide à moins que la prise ait été spécifiquement conçue pour être utilisée dans les endroits humides. • Ne jamais toucher les fils de téléphone ou de l'équipement terminal non isolés à moins que la ligne téléphonique n'ait été débranchée de l'interface réseau. Intermec Technologies…

Text truncated - open the document above for the full version.

A Company February 27, 2001 Inte rmec Technologies Corporation Systems and Solutions 550 Second Street S.E. Cedar Rapids, IA 52401 Federal Communications Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd. Columbia, Md. 21046 FCC ID: EHAWANRIM802 Subject: FCC Part 90 Certification Application for Intermec Technologies Corporation RIM 802 radio This is to inform that Intermec Technologies Corporation is submitting a new filing for our radio modem Model RIM 802 for Part 90 Certification. The Model RIM 802 is a radio modem intended for integration into our equipment to allow wireless data communication. All required tests in compliance with Parts 2 and 90 of the FCC Rules including MPE for remote antennas have been completed by RIM via Com-Serve Corporation (Electrohome Electronics Ltd. – Roseville), APREL Laboratories and Research In Motion with satisfactory results as provided in the attached Exhibits. All required tests in compliance with Part 15 of the FCC Rules have been completed by Intermec Technologies with satisfactory results and kept on file for “Declaration of Conformity” requirements pursuant to Section 15.101(b) and (c)(1) of FCC rules. Intermec Technologies Corporation would like to request confidentiality as indicated in the Form 731, Item 8 and as requested in the letter detailing those items to be kept confidential. Please do hesitate to call at (319) 846-2415 or email at [email protected] should you require additional information or have any questions. Yours truly, Dave Fry, Regulatory Engineer II Intermec Technologies Corporation EMC Test Laboratory

A Company February 27, 2001 Inte rmec Technologies Corporation Systems and Solutions 550 Second Street S.E. Cedar Rapids, IA 52401 Federal Communications Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd. Columbia, Md. 21046 FCC ID: EHAWANRIM802 Subject : Letter requesting confidentiality of RIM radio modem device FCC Certification application. Dear Sirs, Pursuant to CFR 47 Chapter 1 Section 0.459, Intermec Technologies Corporation and Research In Motion Limited (RIM) requests that the following identified detailed technical information regarding the R802D-2-O device be held confidential by the Federal Communication Commission (FCC) and as such be withheld from public inspection. Pursuant to CFR 47 Chapter 1 Sections 0.457(d) and 0.457(d)(2)(i) the exhibits contain details of trade secrets and technical data that is customarily guarded from competitors and not released to the public by Research In Motion Limited. The specific parts of the Exhibits indicated in this letter are considered confidential by RIM and as such should be prevented from disclosure to public and competitors. RIM has taken necessary measures to have limited access to confidential documents only to RIM internal employees on a need-to-know basis, and have signed confidentiality agreements with employees. In addition these documents have not been released to Intermec Technologies. The required documents to support my “Original Request for Grant” must come from Research In Motion Limited of Waterloo, Ontario, Canada. (RIM) As these are proprietary documents, they will be sent directly to this grant application from RIM. This letter and confidential information blank page enables the confidentially fee to be paid using the electronic filing system. Intermec requests the FCC office keep the Exhibits with specific sections described held confidential for a period of 5 years to allow RIM to recoup expenses related to development of their product. The information and trade secrets are currently a marketing and/or technical advantage over the competition. Release of this information would place undue burdens upon RIM, a burden RIM should not bear to support approval of this product. The following Exhibits with specific sections described, submitted with the Form 731 Attachments should be held confidential: Page 2FCC Confidentiality Request, November 13, 2000 Exhibit Parts List/Tune Up Info Procedur.doc “DOC-01606-007”, Users.doc “DOC-1606-006” CFR 47 Section 2.1033(c)(9) - Description of operational, test,.and device tune-up technical procedure and operators’ manual. Section 010-10, CFR 47 Section 2.1033 (c) (10) - Description of Circuitry and Devices provided for: frequency stabilizing circuitry, suppression of spurious radiation, circuits for modulation limiting, and circuits for power limiting Exhibit Operational Description Section 010-13 and 010-13-1, CFR 47 Section 2.1033 (c) (13) - Description of digital modulation format and necessary bandwidth Exhibit Parts List/Tune Up Info Section 010-13-2 and 010-13-3, CFR 47 Section 2.1033 (c) (13) Modulation generation methods and circuits. Detailed diagrams of modulation format and generation methods and circuits Exhibit Operational Description Section 011-1 and 011-2, CFR 47 Section 2.1033 – Detailed system and functional description Exhibit Parts List/Tune Up Info Section 011-3, CFR 47 Section 2.1033 - Detailed technical RF and power circuit description Exhibit Block Diagram 02400-CERT-FCC-BLOCK-“R802D-2-O RADIO BLOCK”, CFR 47 Section 2.1033 – Detailed technical radio modem block diagram Exhibit Schematics “RIM 802D OEM DataTAC - AMSC” SCH-02400-001 Rev B, CFR 47 Section 2.1033 (c) (10) - Complete technical schematic circuit diagrams Yours truly, Dave Fry, Regulatory Engineer II Intermec Technologies Corporation EMC Test Laboratory

RESEARCH IN MOTION Research In Motion Limited 295 Phillip Street Waterloo, Ontario Canada N2L 3W8 +1 519 888 7465, fax +1 519 888 6906 E-mail: [email protected] Our Ref: 02400-CERT-FCC-COVER-021_modFebruary 28, 2001 Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21045 Reference :FCC ID : L6AR802D-2-O Subject :Letter requesting confidentiality of R802D-2-O radio modem device FCC Certification application . Pursuant to CFR 47 Chapter 1 Section 0.459, Research In Motion Limited (RIM) requests that the following identified detailed technical information regarding the R802D-2-O device be held confidential by the Federal Communication Commission (FCC) and as such be withheld from public inspection. RIM does not disclose proprietary confidential information about our products to any third parties and as such we request that the FCC does the same and forward the confidentiality acceptance letter to RIM. Our FCC submissions are considered proprietary confidential information. Pursuant to CFR 47 Chapter 1 Sections 0.457(d) and 0.457(d)(2)(i) the exhibits contain details of trade secrets and technical data that is customarily guarded from competitors and not released to the public by Research In Motion Limited. The specific parts of the Exhibits indicated in this letter are considered confidential by RIM and as such should be prevented from disclosure to public and competitors. RIM has taken necessary measures to have limited access to confidential documents only to RIM internal employees on a need-to-know basis, and have signed confidentiality agreements with employees. If the disclosure of such information is made public, it will cause serious competitive harm to RIM. Previously, none of the requested confidential Exhibits have been disclosed to third parties by RIM. The following Exhibits with specific sections described, submitted with the Form 731 Attachments should be held confidential: Exhibit Parts List/Tune Up InfoProcedur.doc “DOC-01606-007”, Users.doc “DOC-1606-006” CFR 47 Section 2.1033(c)(9) - Description of operational, test, and device tune-up technical procedure and operators’ manual. Section 010-10, CFR 47 Section 2.1033 (c) (10) - Description of Circuitry and Devices provided for: frequency stabilizing circuitry, suppression of spurious radiation, circuits for modulation limiting, and circuits for power limiting Exhibit Operational DescriptionSection 010-13 and 010-13-1, CFR 47 Section 2.1033 (c) (13) - Description of digital modulation format and necessary bandwidth Exhibit Parts List/Tune Up InfoSection 010-13-2 and 010-13-3, CFR 47 Section 2.1033 (c) (13) – Modulation generation methods and circuits. Detailed diagrams of modulation format and generation methods and circuits Exhibit Operational DescriptionSection 011-1 and 011-2, CFR 47 Section 2.1033 - Detailed system and functional description Exhibit Parts List/Tune Up InfoSection 011-3, CFR 47 Section 2.1033 - Detailed technical RF and power circuit description Exhibit Block Diagram02400-CERT-FCC-BLOCK-“R802D-2-O RADIO BLOCK”, CFR 47 Section 2.1033 – Detailed technical radio modem block diagram Exhibit Schematics“RIM 802D OEM DataTAC - AMSC” SCH-02400-001 Rev B, CFR 47 Section 2.1033 (c) (10) - Complete technical schematic circuit diagrams Yours truly, MasudS.Attayi,P.Eng. Senior Certification Engineer Research In Motion Limited ( 519 ) 888 – 7465 x2442 [email protected] RESEARCH IN MOTION Research In Motion Limited 295 Phillip Street Waterloo, Ontario Canada N2L 3W8 +1 519 888 7465, fax +1 519 888 6906 E-mail: [email protected] Our Ref: 02400-CERT-FCC-Cover-022_modFebruary 28, 2001 Federal Communications Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd. Columbia, Md. 21046 FCC ID:L6AR802D-2-O Subject:FCC Part 90 Certification Application for Research In Motion Limited, Model R802D-2-O This is to inform that Research In Motion is submitting the technical documentation of our radio modem Model R802D-2-O (existing FCC ID: L6AR802D-2-O ) in support of the application for Certification of our integrator, Intermec Units, with FCC ID EHAWANRIM802. The Model R802D-2-O is a radio modem intended for integration into other equipment to allow wireless data communication. All required documents in compliance with Parts 2 and 90 of the FCC Rules have been provided in the attached Exhibits. Research In Motion would like to request confidentiality as indicated in the Form 731, Item 8 and as requested in the letter Ref: CERT-01677-021_mod, under Exhibit “Covering Letters”. Please do not hesitate to call at (519) 888-7465 x2442 or email at [email protected] should you require additional information or have any questions. Yours truly, MasudS.Attayi,P.Eng. Senior Certification Engineer Research In Motion Limited ( 519 ) 888 – 7465 x2442 [email protected]

A Company April 17, 2001 Inte rmec Technologies Corporation Systems and Solutions 550 Second Street S.E. Cedar Rapids, IA 52401 FCC, Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Dear Sirs, I have just received confirmation of a new terminal that will use the RIM802 radio currently under review for certification, reference FCC ID: EHAWANRIM802 confirmation number EA100189. I have requested the radio be filed as a module to allow integration within terminals of similar size or larger without the need to re-file for FCC approval. I have downloaded for review the following three photographs to show the physical differences between the 6100 that was tested for SAR with the RIM802 radio and the new 700 terminal from Intermec. The antennas will be of similar construction, low gain dipole, with placements at the top of the unit. The burdens of approval for SAR in hand-held devices are excessive. Currently testing to date for the RIM 802 (EHAWANRIM802) and RIM 902 (EHAWANRIM902-6100) show body exposure usage requires persons to remain 7/8 of an inch from the center of the antenna to be compliant. Considering normal usage for our units and the radio applications Intermec would appreciate consideration to modular radio approval for hand operated terminals. Dave Fry Regulatory Engineer Intermec Technologies Corporation

Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 1 of 5 6110 SAR, RIM R902M-2-O RADIO, Appendix A, Radio Module and Antenna Photographs Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 802 REPORT NO: 20010120-1 DATE: January 20, 2001 APPENDIX A RADIO MODULE AND ANTENNA PHOTOGRAPHS Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 2 of 5 6110 SAR, RIM R902M-2-O RADIO, Appendix A, Radio Module and Antenna Photographs Photo 1: Shows the front view of the radio module. Photo 2: Shows the back side of the radio module. Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 3 of 5 6110 SAR, RIM R902M-2-O RADIO, Appendix A, Radio Module and Antenna Photographs Photo 3: Shows the side view of the radio module. 4: Photo Shows the top view of the radio module. Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 4 of 5 6110 SAR, RIM R902M-2-O RADIO, Appendix A, Radio Module and Antenna Photographs Photo 5: Shows the bottom view of the radio module and antenna connector. 6: Photo Shows the Centurion antenna. Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 5 of 5 6110 SAR, RIM R902M-2-O RADIO, Appendix A, Radio Module and Antenna Photographs Photo 7: Photo Shows the Mobile Mark antenna.

Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 1 of 7 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix C, Tablet Computer Photographs and Radio Installation Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 802 REPORT NO: 20010120-1 DATE: January 20, 2001 APPENDIX C TABLET COMPUTER PHOTOGRAPHS AND RADIO INSTALLATION Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 2 of 7 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix C, Tablet Computer Photographs and Radio Installation Photo 1: Shows a close-up view of the RIM802 radio installed within the 6100 tablet computer. Photo 2: Shows the RIM802 radio within the 6100 showing the case back next to the opened unit. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 3 of 7 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix C, Tablet Computer Photographs and Radio Installation Photo 5: Shows the back view of the 6100 tablet computer. Photo 6: Shows the top view of the 6100 with Mobile Mark antenna. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 4 of 7 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix C, Tablet Computer Photographs and Radio Installation Photo 7: Shows a close-up view of the RIM802 radio installed within the 6600 tablet computer. Photo 8: Shows the RIM802 radio within the options compartment of the 6600, hard-drive lifted. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 5 of 7 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix C, Tablet Computer Photographs and Radio Installation Photo 9: Shows the 6600 hard-drive installed above the RIM802 radio. Photo 10: Shows the back of the 6600 with the options compartment closed. Note, Centurion antenna is shown. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 6 of 7 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix C, Tablet Computer Photographs and Radio Installation Photo 11: Shows the back view of the 6600 tablet computer. Photo 12: Shows the top view of the 6600, this unit also has the optional GPS antenna. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 7 of 7 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix C, Tablet Computer Photographs and Radio Installation Photo 13: Shows the 6600 within the vehicle dock and the remote antenna connected.

Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 1 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 802 REPORT NO: 20010120-1 DATE: January 20, 2001 TYPICAL USE PHOTOGRAPHS Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 2 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 1: Shows the 6100 and right-hand user during normal operation. Photo 2: Shows the 6100 and left-hand user during normal operation. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 3 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 3: Shows the 6100 tablet computer within the pouch in operators’ belt. Photo 4: Shows the 6100 tablet computer within the pouch, antenna closest to operator. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 4 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 5: Shows the 6100 tablet computer within the pouch, antenna away from the operator. Photo 6: Shows close-up of 6100 forward within the pouch with antenna away from the operator. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 5 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 7: Shows close-up of 6100 backwards within the pouch with antenna toward from the operator. Photo 8: Shows the belt strap on the back of the pouch. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 6 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 9: Shows detail of the distance to the antenna to the user with the 6100 within the pouch. 6100 facing forward. Photo 10: Shows detail of the distance to the antenna to the user with the 6100 within the pouch. 6100 facing backwards. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 7 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 11: Shows the front view of the 6100 vehicle dock system with the external antenna. Photo 12: Shows the back view of the 6100 vehicle dock system with the external antenna. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 8 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 13: Shows the 6600 and right-hand user during normal operation. Photo 14: Shows the 6600 and left-hand user during normal operation. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 9 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 15: Shows the 6600 tablet computer while carried by the hand-strap, transmitter in standby. Photo 16: Shows possible holding of the 6600 while transmitter is in standby, 0.2mS TX once every 10 minutes. Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 10 of 10 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix D, Typical Use Photos Photo 16: Shows a 6600 typical installation within a utility truck. Photo 17: Shows another typical 6600 installation within a utility truck.

Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 1 of 4 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix B, Label and Placement Diagrams Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 802 REPORT NO: 20010120-1 DATE: January 20, 2001 APPENDIX B LABEL AND PLACEMENT DIAGRAMS Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 2 of 4 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix B, Label and Placement Diagrams v FCC ID: EHACWANRIM802 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio Assembly Label Label Placement and Label Diagram Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 3 of 4 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix B, Label and Placement Diagrams Label Placement (Inside Customer Accessible Memory Card Door) Label is placed next to ARDIS serial number label required for cellular phone provider access. Label Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 4 of 4 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix B, Label and Placement Diagrams Label ARDIS Radio RIM R802D-2-O Contains TX FCC ID:EHAWANRIM802

Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 1 of 4 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix B, Label and Placement Diagrams Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 802 REPORT NO: 20010120-1 DATE: January 20, 2001 APPENDIX B LABEL AND PLACEMENT DIAGRAMS Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 2 of 4 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix B, Label and Placement Diagrams v FCC ID: EHAWANRIM802 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio Assembly Label Label Placement and Label Diagram Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 3 of 4 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix B, Label and Placement Diagrams Label Placement (Inside Customer Accessible Memory Card Door) Label is placed next to ARDIS serial number label required for cellular phone provider access. Label Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 4 of 4 RIM R802D-2-O Radio, 6100, 6600, SAR Portable, Appendix B, Label and Placement Diagrams Label ARDIS Radio RIM R802D-2-O Contains TX FCC ID:EHAWANRIM802

Intermec Technologies CorporationFCC ID: EHAWANRIM802 EMC Test LabREPORT NO: 20010120-1 DOC. NO.: 577-500-976 Page 1 of 8 RIM R802D-2-O Radio, 6100, 6600, SAR Portable Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 802 REPORT NO: 20010120-1 DATE: January 20, 2001 This report concerns:Original Grant X Class II change Equipment Type: Cellular Radio Certified Under FCC Part 90 Request issue of the grant immediately upon completion of review. Measurement procedure used: FCC Rules Part 1, 2 and OET Bulletin 65 Repor…

Text truncated - open the document above for the full version.