EHAWANRIM902-6100WIRELESS DATA TERMINAL

Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 1 of 2 6110 SAR, RIM R902M-2-O RADIO, Appendix E, Declaration of Conformity Insert Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 902 REPORT NO: 20000822-1 DATE: August 22, 2000 APPENDIX E DECLARATION OF CONFORMITY INSERT, USER INFORMATION Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 2 of 2 6110 SAR, RIM R902M-2-O RADIO, Appendix E, Declaration of Conformity Insert Compliance Statement Insert Device Name: Hand-held ComputerModel Number: 6110 The responsible party for the compliance of this device is:Intermec Technologies Corporation Norand Mobile System Division 550 Second Street SE Cedar Rapids, Iowa 52401 USA (319) 369-3100 CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in perso nal injury, fire, o r battery explo sio n. This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may expose hazards to the operator or nearby persons, void the compliance of this product and may result in the loss of the users authority to operate the equipment. RIM 902 Mobitex Radio Users FCC ID: EHAWANRIM902-6100 WARNING: per the FCC RF (radio frequency) exposure requirements, (1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to FCC RF exposure requirements. (2) The user shall not touch the terminal antenna and is to remain 22-mm (7/8 of and inch) from the center of the antenna while the transceiver is in use. (3) When installing and using Intermec approved remote antennas associated the vehicle dock, a 23-cm (9-inch) passing distance must be maintained from any body part of the user or near by persons and the remote antenna. (4) Cables attached to the remote antennas must have a minimum length of 52-cm (6 feet) to provide the proper losses to control RF exposure. (5) The correct mounting for external or remote antennas would be on a ground plane (vehicle roof), and positioning the antenna such that the minimum 23 cm is kept from any edge of the vehicle rooftop and the remote antenna. FCC Digital Emis s ions Compliance This e q uip me nt ha s b e e n te s te d a nd fo und to c o mp ly with the limits fo r a C la s s B d igita l d e vic e , p urs ua nt to P a rt 1 5 o f the F C C Rule s . The s e limits a re d e s igne d to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will no t o c c ur in a p a rtic ula r ins ta lla tio n. If this e q uip me nt d o e s c a us e ha rmful inte rfe re nc e to ra d io o r te le vis io n reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian D igital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C e t a p p a re il numé riq ue d e la c la s s e B re s p e c te to ute s le s e xige nc e s d u Rè gle me nt s ur le ma té rie l b ro uille ur d u C a na d a . Telephone Installation Warning Notices The following notices apply to equipment that may be connected to telephone lines or systems. For your personal safety, and to protect this equipment from potential electrical or physical damage, do NOT connect equipment to telephone lines or data communication equipment unless the following warnings have been read, understood, and complied with. • N ever install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. • Avoid using telephone (other than cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. • Do not use the telephone to report a gas leak in the vicinity of the leak. Installation do téléphone : avertissements Les avertissements qui suivent s'appliquent à tout équipement qui peut être branché aux lignes ou systemes téléphoniques. Pour votre sécurité personnelle et pour protéger l'équipement de tout dommage électrique ou physique potentiel, NE PAS brancher un ordinateur tablette électronique ou ses périphériques aux lignes téléphoniques ou équipements avant que les avertissements suivants aient été lus, compris et observés: • Ne jamais installer de câblage téléphonique pendant un orage électrique. • Ne jamais installer de prise téléphonique dans un endroit humide à moins que la prise ait été spécifiquement conçue pour être utilis é e d a ns le s e nd ro its humid e s . • Ne jamais toucher les fils de téléphone ou de l'équipement terminal non isolés à moins que la ligne téléphonique n'ait été débranchée de l'interface réseau.

,QWHJUDWRU∑V *XLGH 5,00 2(05DGLR0RGHP RIM 902M OEM Radio Modem Integrator’s Guide Last Updated: January 11, 1999 Model No. R902M-2-O © 1999, RESEARCH IN MOTION LIMITED Research In Motion and RIM are registered trademarks of Research In Motion Ltd. Mobitex is a trademark of the Swedish Telecommunications Administration. MS-DOS is a registered trademark, and Windows is a trademark, of Microsoft Corp. Warning: This document is for the use of licensed users only. Any unauthorised copying, distribution or disclosure of information is a violation of copyright laws. While every effort has been made to ensure technical accuracy, information in this document is subject to change without notice and does not represent a commitment on the part of Research In Motion Limited. Research In Motion 295 Phillip Street Waterloo, Ontario Canada N2L 3W8 tel. (519) 888-7465 fax (519) 888-7884 E-mail:[email protected] Web site: www.rim.net MOBITEX Interface, specified in Specification LZBA 703 1001, compatible equipment FCC Compliance Statement (USA) FCC Class B Part 15 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacture’s instructions, may cause harmful interference to radio communications. There is no guarantee, however, that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: x Re-orient or relocate the receiving antenna. x Increase the separation between the equipment and receiver. x Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. x Consult the dealer or an experienced radio/TV technician for help. Industry Canada Certification This device complies with Industry Canada RSS 119, under certification number TBD. IC Class B compliance This device complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada. Contents FCC Compliance Statement (USA) ........................................ i Industry Canada Certification ............................................... ii About this guide.................................................................... v 1. Introduction............................................................... 1 Radio performance...................................................................... 1 Mobitex network technology ....................................................... 4 FCC radio frequency exposure rules............................................ 5 2. Getting started........................................................... 9 Test board overview ...................................................................10 How to connect the test board.....................................................11 The MENU diagnostics tool .......................................................12 3. Mechanical integration ........................................... 21 Environmental properties...........................................................21 Physical properties .....................................................................22 Mounting methods .....................................................................24 Cables and connectors................................................................27 4. Power requirements ................................................ 31 Load specifications ....................................................................31 Batteries ....................................................................................32 Plug-in supplies.........................................................................34 Automotive supplies...................................................................34 5. Interface specification ............................................. 35 MASC and RAP link-layer protocols.........................................35 Pin descriptions .........................................................................37 How to turn the radio on and off ................................................42 Interface to an RS-232 device.....................................................43 Interface to microprocessor ........................................................43 6. Antenna selection .................................................... 45 Selecting an antenna ..................................................................45 Introduction to antenna terminology ..........................................46 Positioning the antenna..............................................................49 Shielding ...................................................................................50 Specifications ...................................................................... 51 Glossary of terms ................................................................ 53 Index.................................................................................... 55 About this guide This document is a guide to integrating the RIM 902M OEM radio mode…

Text truncated - open the document above for the full version.

Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 1 of 2 6110 SAR, RIM R902M-2-O RADIO, Appendix E, Declaration of Conformity Insert Technologies Corporation EMC Test Laboratory Cedar Rapids, IA MEASUREMENT/TECHNICAL REPORT Intermec Technologies Corporation Cellular Radio Module OEM From RIM 902 REPORT NO: 20000822-1 DATE: August 22, 2000 APPENDIX E DECLARATION OF CONFORMITY INSERT, USER INFORMATION Intermec Technologies CorporationFCC ID: EHAWANRIM902-6100 EMC Test LabREPORT NO: 20000822-1 DOC. NO.: 577-500-970 Page 2 of 2 6110 SAR, RIM R902M-2-O RADIO, Appendix E, Declaration of Conformity Insert Compliance Statement Insert Device Name: Hand-held ComputerModel Number: 6110 The responsible party for the compliance of this device is:Intermec Technologies Corporation Norand Mobile System Division 550 Second Street SE Cedar Rapids, Iowa 52401 USA (319) 369-3100 CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result in perso nal injury, fire, o r battery explo sio n. This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of the users authority to operate the equipment. Mobitex Radio Users FCC ID: EHAWANRIM902-6100 WARNING: per the FCC RF exposure requirements, the user shall not touch the terminal antenna and is to remain 22-mm (7/8 of and inch) from the center of the antenna while the transceiver is in use. When using remote mounted antennas associated the vehicle dock, a 20-cm (8-inch) distance must be maintained from the operator and remote antenna. FCC Digital Emis s ions Compliance This e q uip me nt ha s b e e n te s te d a nd fo und to c o mp ly with the limits fo r a C la s s B d igita l d e vic e , p urs ua nt to P a rt 1 5 o f the F C C Rule s . The s e limits a re d e s igne d to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will no t o c c ur in a p a rtic ula r ins ta lla tio n. If this e q uip me nt d o e s c a us e ha rmful inte rfe re nc e to ra d io o r te le vis io n reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio of television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian D igital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C e t a p p a re il numé riq ue d e la c la s s e B re s p e c te to ute s le s e xige nc e s d u Rè gle me nt s ur le ma té rie l b ro uille ur d u C a na d a . Telephone Installation Warning Notices The following notices apply to equipment that may be connected to telephone lines or systems. For your personal safety, and to protect this equipment from potential electrical or physical damage, do NOT connect equipment to telephone lines or data communication equipment unless the following warnings have been read, understood, and complied with. • N ever install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. • Avoid using telephone (other than cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. • Do not use the telephone to report a gas leak in the vicinity of the leak. Installation do téléphone : avertissements Les avertissements qui suivent s'appliquent à tout équipement qui peut être branché aux lignes ou systemes téléphoniques. Pour votre sécurité personnelle et pour protéger l'équipement de tout dommage électrique ou physique potentiel, NE PAS brancher un ordinateur tablette électronique ou ses périphériques aux lignes téléphoniques ou équipements avant que les avertissements suivants aient été lus, compris et observés: • Ne jamais installer de câblage téléphonique pendant un orage électrique. • Ne jamais installer de prise téléphonique dans un endroit humide à moins que la prise ait été spécifiquement conçue pour être utilis é e d a ns le s e nd ro its humid e s . • Ne jamais toucher les fils de téléphone ou de l'équipement terminal non isolés à moins que la ligne téléphonique n'ait été débranchée de l'interface réseau.

A Company August 24, 2000 Inte rmec Technologies Corporation 550 Second Street S.E. Cedar Rapids, IA 52401 Federal Communication Commission Equipment Approval Services PO Box 358315 Pittsburgh, PA 15251-5315 Dear Sir: SUBJECT: FCC Certification Application, FCC ID: EHAWANRIM902-6100 Please review the following application for a change in identification. A 159 payment and an electronic application for the change has been submitted by Intermec Technologies Corporation. Intermec Technologies Corporation will integrate the radio within another tablet computer for delivery services inventory automation. Compliance to the RF exposure section of the FCC rules is addressed within this application. There are no changes to the radio assembly. The data currently on file with the FCC is still representative of this products regulatory characteristics. Accompanying this letter are an application report with appendixes of photographs of the label placement, as well as label diagrams and a SAR report from APREL Laboratories for your records. Intermec will be using two antennas that are not listed on the original grant approved for Research In Motion Ltd. (RIM). These were tested for SAR to address the RF exposure requirements of the FCC. The long antenna is 7-inch (17.8-cm) long ½ wave end-fed whip dipole from Centurion part number (PN) CAF28766, Intermec PN 805-490-004. Gain –2.5 dBd, VSWR 1.5:1, 50 Ohms. The short antenna is 3.5-inch (9-cm) long ¼ wave end fed dipole from Mobile Mark model number PSTN2-899CI, Intermec PN 805-572-002. Gain –1.2 dBd, VSWR 2-2.5:1, 50 Ohms The antennas originally listed by RIM will continue to be used for remote antenna installations. Our application is for approval of the radio as a module not tied to a specific tablet computer. The tablet computers referenced in this application for approval will have the same exterior shell and antenna placements. The processing capability and options for memory, display and peripheral connection will change. If the radio is to be used in a tablet computer with substantially different antenna placement or case size, we will review the conditions for approval addressed herein and notify the FCC with a permissive change or request for new grant. Please contact me at (319) 846-2415 or e-mail [email protected] should you have any question regarding this change in FCC ID. Sincerely, Dave Fry, Regulatory Engineer II Intermec Technologies Corporation Norand Mobile Systems Division EMC Test Laboratory Enc.Electronic 731 Application form Report with photograph and label diagrams

A Company November 13, 2000 Intermec Technologies Corporation Systems and Solutions 550 Second Street S.E. Cedar Rapids, IA 52401 Federal Communications Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd. Columbia, Md. 21046 FCC ID: EHAWANRIM902-6100 Dear Sirs, The FCC request to file this product under “Original Request for Grant” in place of the current “Change of Identification” now requires me to add “Confidentiality” to this application. The required documents to support my “Original Request for Grant” must come from Research In Motion Limited of Waterloo, Ontario, Canada. (RIM) As these are proprietary documents, they will be sent directly to this grant application from RIM. This letter and confidential information blank page enables the confidentially fee to be paid using the electronic filing system. Intermec requests the FCC office keep the Exhibits with specific sections described held confidential for a period of 5 years to allow RIM to recoup expenses related to development of their product. The information and trade secrets are currently a marketing and/or technical advantage over the competition. Release of this information would place undue burdens upon RIM, a burden RIM should not bear to support approval of this product. Exhibit Parts List/Tune Up Info Section 010-9-1 and 010-9-2, CFR 47 Section 2.983(d)(9) - Description of operational, test, and device tune-up technical procedure-“DOC-01606-007”, and operators’ manual-“DOC-01606-008” Section 010-10, CFR 47 Section 2.983(d)(10) - Description of frequency stabilizing circuitry Exhibit Parts List/Tune Up Info Section 010-11-1, CFR 47 Section 2.983(d)(11) - Description of circuits for suppression of spurious radiation Section 010-11-2, CFR 47 Section 2.983(d)(11) - Description of circuits for modulation limiting Section 010-11-3, CFR 47 Section 2.983(d)(11) - Description of circuits for power limiting Exhibit Operational Description Section 010-12 and 010-12-1, CFR 47 Section 2.983(d)(12) -Description of digital modulation format and necessary bandwidth Exhibit Parts List/Tune Up Info Section 010-12-2 and 010-12-3, CFR 47 Section 2.983(d)(12) – Modulation generation methods and circuits. Detailed diagrams of modulation format and generation methods and circuits Exhibit Operational Description Section 011-1 and 011-2, CFR 47 Sections 2.975(a)(3), 2.983(d)(6) and 2.1033(b)(4) - Detailed system and functional description Page 2FCC Confidentiality Request, November 13, 2000 Exhibit Parts List/Tune Up Info Section 011-3, CFR 47 Sections 2.975(a)(3), 2.983(d)(6) and 2.1033(b)(4) - Detailed technical RF and electrical circuit description Exhibit Block Diagram 01947-CERT-FCC-BLOCK-“R902M-2-O RADIO BLOCK”, CFR 47 Section 2.983(d)(6) – Detailed technical radio modem block diagram Exhibit Schematics “Tadpole OEM” SCH-01947-001, CFR 47 Section 2.983(d)(7) - Complete technical schematic circuit diagrams Attached is a letter repeating my request for confidentiality from RIM to support their original request for grant. Subject: FCC Part 90 Type Acceptance Application for Research In Motion Limited, Model R902M-2-O FCC ID : L6AR902M-2-O Grant Date: 07/1999 Yours truly, Dave Fry, Regulatory Engineer II Intermec Technologies Corporation EMC Test Laboratory RESEARCH IN MOTION Research In Motion Limited 295 Phillip Street Waterloo, Ontario Canada N2L 3W8 +1 519 888 7465, fax +1 519 888 6906 E-mail: [email protected] Our Ref: 01947-CERT-FCC-COVER-021April 9, 1999 Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21045 Reference : FCC ID : L6AR902M-2-O Subject : Letter requesting confidentiality of R902M-2-O radio modem device FCC type acceptance application. Pursuant to CFR 47 Chapter 1 Section 0.459, Research In Motion Limited (RIM) requests that the following identified detailed technical information regarding the R902M-2-O device be held confidential by the Federal Communication Commission (FCC) and as such be withheld from public inspection. Pursuant to CFR 47 Chapter 1 Sections 0.457(d) and 0.457(d)(2)(i) the exhibits contain details of trade secrets and technical data that is customarily guarded from competitors and not released to the public by Research In Motion Limited. The specific parts of the Exhibits indicated in this letter are considered confidential by RIM and as such should be prevented from disclosure to public and competitors. RIM has taken necessary measures to have limited access to confidential documents only to RIM internal employees on a need-to-know basis, and have signed confidentiality agreements with employees. If the disclosure of such information is made public, it will cause serious competitive harm to RIM. Previously, none of the requested confidential Exhibits have been disclosed to third parties by RIM. RIM requests the FCC office to keep the Exhibits mentioned here from disclosure to third parties for the time frame of 5 years. The confidentiality period of five years that we have requested is necessary to maintain trade secrets and other proprietary information contained in the components of our products. The period has been selected so as to permit RIM to recoup its research and development expenses that have been incurred to develop such information and trade secrets and to ensure that those items that can be the subject of patents are adequately protected. A shorter period of time would require RIM to divulge information that, because of its secret nature, gives RIM a marketing or technolgical advantage over its competitor while such information has economic or technical value. Such an event would place an undue burden on RIM, a burden RIM should not have to bear in order to obtain an equipment grant from the FCC. The following Exhibits with specific sections described, submitted with the Form 731 Attachments should be held confidential: Exhibit Parts List/Tune Up Info Section 010-9-1 …

Text truncated - open the document above for the full version.

RESEARCH IN MOTION Research In Motion Limited 295 Phillip Street Waterloo, Ontario Canada N2L 3W8 +1 519 888 7465, fax +1 519 888 6906 E-mail: [email protected] Our Ref: 01947-CERT-FCC-COVER-021November 15, 2000 Federal Communication Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21045 Reference :FCC ID : L6AR902M-2-O Subject :Letter requesting confidentiality of R902M-2-O radio modem device FCC Certification application. Pursuant to CFR 47 Chapter 1 Section 0.459, Research In Motion Limited (RIM) requests that the following identified detailed technical information regarding the R902M-2-O device be held confidential by the Federal Communication Commission (FCC) and as such be withheld from public inspection. RIM does not disclose proprietary confidential information about our products to any third parties and as such we request that the FCC does the same and forward the confidentiality acceptance letter to RIM. Our FCC submissions are considered proprietary confidential information. Pursuant to CFR 47 Chapter 1 Sections 0.457(d) and 0.457(d)(2)(i) the exhibits contain details of trade secrets and technical data that is customarily guarded from competitors and not released to the public by Research In Motion Limited. The specific parts of the Exhibits indicated in this letter are considered confidential by RIM and as such should be prevented from disclosure to public and competitors. RIM has taken necessary measures to have limited access to confidential documents only to RIM internal employees on a need-to-know basis, and have signed confidentiality agreements with employees. If the disclosure of such information is made public, it will cause serious competitive harm to RIM. Previously, none of the requested confidential Exhibits have been disclosed to third parties by RIM. The following Exhibits with specific sections described, submitted with the Form 731 Attachments should be held confidential: Exhibit Parts List/Tune Up InfoSection 010-9-1 and 010-9-2, CFR 47 Section 2.983(d)(9) - Description of operational, test, and device tune-up technical procedure-“DOC-01606-007”, and operators’ manual-“DOC- 01606-008” Section 010-10, CFR 47 Section 2.983(d)(10) - Description of frequency stabilizing circuitry Exhibit Parts List/Tune Up InfoSection 010-11-1, CFR 47 Section 2.983(d)(11) - Description of circuits for suppression of spurious radiation Section 010-11-2, CFR 47 Section 2.983(d)(11) - Description of circuits for modulation limiting Section 010-11-3, CFR 47 Section 2.983(d)(11) - Description of circuits for power limiting Exhibit Operational DescriptionSection 010-12 and 010-12-1, CFR 47 Section 2.983(d)(12) - Description of digital modulation format and necessary bandwidth Exhibit Parts List/Tune Up InfoSection 010-12-2 and 010-12-3, CFR 47 Section 2.983(d)(12) – Modulation generation methods and circuits. Detailed diagrams of modulation format and generation methods and circuits Exhibit Operational DescriptionSection 011-1 and 011-2, CFR 47 Sections 2.975(a)(3), 2.983(d)(6) and 2.1033(b)(4) - Detailed system and functional description Exhibit Parts List/Tune Up InfoSection 011-3, CFR 47 Sections 2.975(a)(3), 2.983(d)(6) and 2.1033(b)(4) - Detailed technical RF and electrical circuit description Exhibit Block Diagram01947-CERT-FCC-BLOCK-“R902M-2-O RADIO BLOCK”, CFR 47 Section 2.983(d)(6) – Detailed technical radio modem block diagram Exhibit Schematics“Tadpole OEM” SCH-01947-001, CFR 47 Section 2.983(d)(7) - Complete technical schematic circuit diagrams Yours truly, MasudS.Attayi,P.Eng. Senior Certification Engineer Research In Motion Limited ( 519 ) 888 – 7465 x 2442 [email protected] RESEARCH IN MOTION Research In Motion Limited 295 Phillip Street Waterloo, Ontario Canada N2L 3W8 +1 519 888 7465, fax +1 519 888 6906 E-mail: [email protected] Our Ref: 01947-CERT-FCC-Cover-022November 15, 2000 Federal Communications Commission Equipment Authorization Division Application Processing Branch 7435 Oakland Mills Rd. Columbia, Md. 21046 FCC ID:L6AR902M-2-O Subject:FCC …

Text truncated - open the document above for the full version.