ELY547-47-1012E-TRemote Controller

1 Owner's Manual WIRELESS REMOTE SWITCH MODEL: 47-1012E- T FCC ID: ELY547-47-1012E-T IC: 1492A-471012ET FLAME/HEAT ON/OFF BUTTON Press the Flame/Heat On/Off button to turn the Flame/Heat function ON or OFF. When the heater function is ON, the icon is displayed on the remote control in the upper left hand corner. When this icon is displayed, the red indicator light is activated on the firebox. NOTE When using the remote control the heater runs on a thermostat. Press the or direction keys to adjust the set temperature. Once the desired set temperature is reached the heater will turn OFF. The heater will cycle ON and OFF to maintain the desired set temperature. PURIFIRE ON/OFF BUTTON Press the Purifire™ On/Off button to turn the Purifire™ function ON or OFF. When the Purifire™ function is ON and the Heater icon is NOT displayed on the remote control, the green indicator light is activated on the firebox. NOTE To turn the Flame/Heat and Purifire™ ON or OFF at the same time, press both control buttons simultaneously. DIMMER Press the left “-“ or right “+” direction button to decrease or increase the brightness of the upper lights. NOTE The bar graph located on the display screen indicates the upper light brightness range. FLAME SPEED Press the left “-“ or right “+” direction buttons to decrease or increase the flame speed. NOTE The bar graph located on the display screen indicates the speed range of the flame. 2 COUNTDOWN TIMER To set the Countdown timer, press the left “-“ or right “+” direction buttons to decrease or increase by 30 minute decrements or increments. The countdown timer can be set from 30 minutes to 8 hours. The fireplace will automatically turn OFF when the sleep timer reaches 0 minutes. PURIFIRE SPEED The Purifire™ includes a high efficiency filter to help improve the quality of air. When the Purifire™ function is ON, the green indicator light is activated on the firebox. Press the left “-“ or right “+” direction buttons to select LOW or HIGH. NOTE The Purifire™ can also be turned On/Off by pressing the Purifire™ On/Off button. SET TEMPERATURE Press the “-“ or right “+” direction button together of to select between °F and °C. Press the “-“ or right “+” direction button to decrease or to increase temperature. 3 INITIALIZING THE REMOTE CONTROL 1. Plug cord into 120 volt wall outlet. 2. Set the 3 position manual control to Position 1 (left position). 3. Press and hold the initialization button on the Switch Power. 4. While holding the initialization button, press the flame ON/OFF button or the Purifire™ ON/OFF button on the remote control transmitter. 5. Release the initialization button on the Switch Board. The remote control is now ready for operation. Switch Board Panel CAUTION 1. For indoor use in dry areas only. 2. 120 volt AC supply. 4 WARNING The Manufacturer is not responsible for any radio and TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada,. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
            Specifications Input Rating....................................................................................................AC 100~240V, 50/60Hz Output Rating.................................................................................................. AC 100~240V, 50/60Hz Resistive Load............................................................................................................1200W Incandescent Lamp.......................................................................................................270W Operation Temperature...................................................................................................... 0 - 40 к Storage Temperature .....................................................................................................-25 - 60 к 5 French                !             "    # $   #   %  & '  "  #      ( )   * )   * #        !…

Text truncated - open the document above for the full version.

External Photo Front View of the product Rear View of the product Battery compartment Battery Cover

Label location

Internal Photo Internal View of the product Internal View of the product Inner Circuit Top View Inner Circuit Bottom View

TEST REPORT No: (5211)239-0015 BUREAU VERITAS HONG KONG LIMITED – Kowloon Bay Office 1/F Pacific Trade Centre, 2 Kai Hing Road, Kowloon Bay, Kowloon,HONG KONG Tel: +852 2331 0888 Fax: +852 2331 0889 www.cps.bureauveritas.com This report is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. Our report is limited to the test samples identified herein. The results set forth in this report are not necessarily indicative or representative of the statistical quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof. You shall have thirty days from receipt of this report to request additional testing of the samples or to notify us of any errors or omissions relating to our report, provided, however, such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Page 2 of 27 Location of the test laboratory Radiated and Conducted emissions measurements are investigated and taken pursuant to the procedures of ANSI C63.4 – 2003. An Open Area Test Site and Full Anechoic Chamber (FCC Listed Site, Registration No. 642151) are set up for investigation and located at : BUREAU VERITAS HONG KONG LIMITED, EMC CENTRE No. 2106-2107, 21/F., Westin Centre, 26 Hung To Road, Kwun Tong, Kowloon, Hong Kong List of measuring equipment Radiated Emission EQUIPMENT MANUFACTURER MODEL NO. SERIAL NO. CALIBRATION DUE EMI TEST RECEIVER R&S ESCI 100379 05-SEP-2012 LOOP ANTENNA ETS-LINDGREN 6502 00102266 12-MAY-2012 BILOG ANTENNA SCHAFFNER CBL6112D 25229 16-SEP-2012 OPEN AREA TEST SITE BVCPS N/A N/A 07-JUL-2012 ANECHOIC CHAMBER ALBATROSS M-CDC 80374004499B 26-OCT-2011 COAXIAL CABLE SUHNER N/A N/A 18-SEP-2012 Remarks:- N/A : Not Applicable or Not Available The measurement instrumentation uncertainty would be taking into consideration on each of the test result TEST REPORT No: (5211)239-0015 BUREAU VERITAS HONG KONG LIMITED – Kowloon Bay Office 1/F Pacific Trade Centre, 2 Kai Hing Road, Kowloon Bay, Kowloon,HONG KONG Tel: +852 2331 0888 Fax: +852 2331 0889 www.cps.bureauveritas.com This report is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. Our report is limited to the test samples identified herein. The results set forth in this report are not necessarily indicative or representative of the statistical quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof. You shall have thirty days from receipt of this report to request additional testing of the samples or to notify us of any errors or omissions relating to our report, provided, however, such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Page 3 of 27 Equipment Under Test [EUT] Description of Sample: Model Name: 2.4GHz Midline Remote Model Number: 47-1012E-T Rating: 3Vd.c (“AAA” size battery x 2) Description of EUT Operation: The Equipment Under Test (EUT) is a JECKSON ELECTRIC CO., LTD. of Remote Control Transmitter . The transmitter is a 12 buttons transmitter and operating at 2402MHz to 2480MHz. The lowest, middle and highest frequencies were tested and the results are shown in the report. The EUT transmit while buttons is being pressed, Modulation by IC, and type is FHSS. The transmitter has different control: 1. Temperature “+” button – temperature setting - increase 2. Temperature “-“button – temperature setting - decrease 3. Dimmer “+” button – brightness setting - increase 4. Dimmer “-“ button – brightness setting - decrease 5. Flame Speed “+” button – flame speed setting - increase 6. Flame Speed “-” button – flame speed setting - decrease 7. Countdown Timer “+” button – countdown timer setting - increase 8. Countdown Timer “-” button – countdown timer setting - decrease 9. Purifire Speed “+” button – purifire speed setting - increase 10. Purifire Speed “-” button – purifire speed setting - decrease 11. Flame/Heat ON/OFF button – flame/heat function ON/OFF control 12. Purifire ON/OFF button – purifire function ON/OFF control Antenna Requirement (Section 15.203) The EUT is use of a permanently antenna. It is PCB trace antenna. The antenna is not replaceable or user serviceable. The requirements of S15.203 are met. There are no deviations or exceptions to the specifications. TEST REPORT No: (5211)239-0015 BUREAU VERITAS HONG KONG LIMITED – Kowloon Bay Office 1/F Pacific Trade Centre, 2 Kai Hing Road, Kowloon Bay, Kowloon,HONG KONG Tel: +852 2331 0888 Fax: +852 2331 0889 www.cps.bureauveritas.com This report is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. Our report is limited to the test samples identified herein. The results set forth in this report are not necessarily indicative or representative of the statistical quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you a…

Text truncated - open the document above for the full version.

Test Set Up Photo