EW4-0201JVAWi-Fi WIN Card

Insert the card to microSD slot in straight Thank you for purchasing the product.Please read this instruction manual before use When mobile PC has lock mechanism, insert card until you hear clicking noise and keep this manual carefully.Please follows cautions and warnings for proper use. S p ecification Hold the tip of card and pull it slowly from a mobile PC When a mobile PC equips lock mechanism, press it until you hear clicking noise to release lock, Compliant IEEE802.11b/g then pull it out slowly Channel IEEE802.11b/g: 11 channels for USA, 13 channels for Europe When card is pulled out by force, failure might occur. Frequency IEEE802.11b/g: 2.4GHz bandwidth (2412 to 2462MHz) (North America)Frequency IEEE802.11b/g: 2.4GHz bandwidth (2412 to 2472MHz) (Europe)Modulation Method DSSS/OFDM Transfer Rate DSSS 1M/2M/5.5M/11Mbps OFDM 6M/9M/12M/18M/24M/36M/48M/54Mbps Antenna 2.4GHz bandwidth chip antenna Power DC3.0V to 3.46V (supplied by connected device) Power Consumption Max. 950mW External Dimension 11(W)×16(H)×0.7(D) mm Raised part on card tip 1.0(D)mm Weight 1.0g or less Hereby, MITSUMI declares that this Mitsumi Wi-Fi WIN card (0201JVA) is in compliance with the essentialrequirements and other relevant provisions of Directive 1999/5/EC.This equipment is marked with the symbol and can be used throughout the European community.This indicates compliance with the R&TTE Directive 1999/5/EC and meets the relevant parts of followingtechnical specifications: Wi-Fi WIN card (0201JVA) Instruction Manual EN 300 328 V1.7.1(2006-10) , Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission Systems; Data transmission equipment operating in the 2.4GHz ISM band and using spreadspectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of theR&TTE Directive.EN 301 489-17 V2.1.1 (2009-05) , Electromagnetic Compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific Conditionsfor Wideband Data and HYPERLAN Equipment.EN 60950-1 , Safety of Information Technology Equipment. EN 62311 , Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz - 300 GHz)Marking by the symbol indicates that usage restrictions apply.France – 2.4GHz for Metropolitan France :In all Metropolitan départements, wireless LAN frequencies can be used under the following conditions, eitherfor public or private use: Indoor use: maximum power (EIRP) of 100mW for the entire 2400-2483.5MHz frequency band Outdoor use: maximum power (EIRP) of 100mW for the 2400-2454MHz band and with maximum power (EIRP) of 10mW for the 2454-2483.5MHz bandCaution: Exposure to Radio Frequency RadiationTo comply with RF exposure compliance requirements, this device and its antenna must not to be co-located oroperating in conjunction with any other antenna or transmitter. This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses, and can radiateradio frequency energy. If not installed and used in accordance with the instructions, it may causeharmful interference to radio communications. However, there is no guarantee that interference willnot occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can bedetermined by tuning the equipment off and on, the user is encouraged to try and correct theinterference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the distance between the equipment and the receiver.-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may causeundesired operation.Any changes or modifications not expressly approved by the party responsible for compliance couldvoid the user’s authority to operate the equipment.Caution: Exposure to Radio Frequency RadiationTo comply with FCC RF exposure compliance requirements, this device and its antenna must not tobe co-located or o p eratin g in con j unction with an y other antenna or transmitter. USA-Federal Communications Commission ( FCC ) How to Insert How to Remove microSD slot Clicking Cover Lock mechanism microSD card Lock mechanism Press it until you hearclicking noise Clicking Insert until you hearclicking noise Card Tip Euro p e-EU Declaration of Conformit y and Restriction s 0984

EW4-0201JVA External Photos

裏面 表面 ミツミ電機 AVC技術部 Ｔ Ｒ FCC ID:EW4-0201JVA 0201JVA Label format and location (TELEC) (JATE) Certification number Certification number MAC ADDRESS MAC 0201JVA MADE IN PHILIPPINE '10.03.01

EW4-0201JVA Internal Photo

FCC OET BULLETIN 65 SUPPLEMENT C SAR EVALUATION REPORT For WiFi-WIN Card (Tested inside of Kohjinsha PA) MODEL: 0201JVA FCC ID: EW4-0201JVA REPORT NUMBER: 10J13061-3B ISSUE DATE: March 10, 2010 Prepared for Mitsumi Electric Co Ltd 1601, Sakai, Atsugi-shi Kanagawa-ken 243, Japan Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 10J13061-3B DATE: March 10, 2010 FCC ID: EW4-0201JVA Page 2 of 22 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- February 20, 2010 Initial Issue -- A March 9, 2010 - Added antenna-to-antenna separation distances in Section 5 - Updated EUT description Sunny Shih B March 10, 2010 - Updated Section 5 Equipment Under Test. - Removed Section 12 Antenna-to-antenna separation distances from this report. Sunny Shih REPORT NO: 10J13061-3B DATE: March 10, 2010 FCC ID: EW4-0201JVA Page 3 of 22 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................................. 4 2. TEST METHODOLOGY ...................................................................................................................... 5 3. FACILITIES AND ACCREDITATION.................................................................................................. 5 4. CALIBRATION AND UNCERTAINTY................................................................................................. 6 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 6 4.2. MEASUREMENT UNCERTAINTY .............................................................................................. 7 5. EQUIPMENT UNDER TEST ............................................................................................................... 8 6. SYSTEM SPECIFICATIONS ............................................................................................................... 9 7. COMPOSITION OF INGREDIENTS FOR TISSUE SIMULATING LIQUIDS .................................... 10 8. LIQUID PARAMETERS CHECK....................................................................................................... 11 8.1. LIQUID CHECK RESULTS FOR 2450 MHZ ............................................................................. 12 9. SYSTEM CHECK .............................................................................................................................. 13 9.1. SYSTEM CHECK RESULTS FOR D2450V2 ............................................................................ 13 10. OUTPUT POWER VERIFICATION............................................................................................... 14 11. SUMMARY OF TEST RESULTS.................................................................................................. 15 11.1. TEST RESULT FOR THE 2.4GHZ BAND................................................................................. 15 12. WORST-CASE SAR TEST PLOTS .............................................................................................. 16 13. ATTACHMENTS ........................................................................................................................... 17 14. TEST SETUP PHOTO .................................................................................................................. 18 15. HOST DEVICE PHOTO ................................................................................................................ 21 REPORT NO: 10J13061-3B DATE: March 10, 2010 FCC ID: EW4-0201JVA Page 4 of 22 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: Mitsumi Electric Co Ltd 1601, Sakai, Atsugi-shi Kanagawa-ken 243, Japan EUT DESCRIPTION: WiFi-WIN Card (Tested inside of Kohjinsha PA) MODEL NUMBER: 0201JVA DEVICE CATEGORY: Portable EXPOSURE CATEGORY: General Population/Uncontrolled Exposure DATE TESTED: February 18, 2010 THE HIGHEST SAR VALUES: FCC/IC Rule Parts Frequency Range [MHz] 1g SAR (mW/g) Limit (mW/g) 15.247 / RSS-102 2400 – 2483.5 0.126 (Tablet mode - Bottom Face) 1.6 Applicable Standards and Test Procedures Test Results OET 65, Supplement C and the following specific Test Procedures: o KDB 248227 SAR measurement procedures for 802.11a/b/g transmitters o KDB 447498 D01 Mobile Portable RF Exposure v04, suppl. to KDB 616217 D03 Pass Compliance Certification Services, Inc. (CCS) tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by CCS based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by CCS and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by CCS will constitute fraud and shall nullify the document. This report must not be used by the client t…

Text truncated - open the document above for the full version.

Date/Time: 2/18/2010 6:57:18 PM Test Laboratory: Compliance Certification Services System Performance Check - D2450V2 DUT: Dipole ; Type: D2450V2; Serial: 748 Communication System: System Check Signal - CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 2.01 mho/m; ε r = 53.9; ρ = 1000 kg/m 3 Phantom section: Flat Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV4 - SN3686; ConvF(6.48, 6.48, 6.48); Calibrated: 3/23/2009 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN:1003 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 d=10mm, Pin=100mW/Area Scan (6x6x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 6.57 mW/g d=10mm, Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 57.2 V/m; Power Drift = 0.235 dB Peak SAR (extrapolated) = 11.0 W/kg SAR(1 g) = 5.32 mW/g; SAR(10 g) = 2.46 mW/g Maximum value of SAR (measured) = 6.96 mW/g Date/Time: 2/18/2010 7:13:15 PM Test Laboratory: Compliance Certification Services System Performance Check - D2450V2 DUT: Dipole ; Type: D2450V2; Serial: 748 Communication System: System Check Signal - CW; Frequency: 2450 MHz;Duty Cycle: 1:1 d=10mm, Pin=100mW/Z Scan (1x1x34): Measurement grid: dx=20mm, dy=20mm, dz=3mm Maximum value of SAR (measured) = 6.84 mW/g

Date/Time: 2/18/2010 10:56:49 PM Test Laboratory: Compliance Certification Services Laptop Mode DUT: Mitsumi; Type: NA; Serial: NA Communication System: 802.11bgn; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2437 MHz; σ = 2 mho/m; ε r = 53.9; ρ = 1000 kg/m 3 Phantom section: Flat Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV4 - SN3686; ConvF(6.48, 6.48, 6.48); Calibrated: 3/23/2009 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN:1003 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 802.11b_ch6/Area Scan (6x6x1): Measurement grid: dx=15mm, dy=15mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.122 mW/g 802.11b_ch6/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 5.59 V/m; Power Drift = 0.284 dB Peak SAR (extrapolated) = 0.205 W/kg SAR(1 g) = 0.122 mW/g; SAR(10 g) = 0.092 mW/g Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.146 mW/g Date/Time: 2/18/2010 9:27:47 PM Test Laboratory: Compliance Certification Services Table Mode_Bottom face DUT: Mitsumi; Type: NA; Serial: NA Communication System: 802.11bgn; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2437 MHz; σ = 2 mho/m; ε r = 53.9; ρ = 1000 kg/m 3 Phantom section: Flat Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV4 - SN3686; ConvF(6.48, 6.48, 6.48); Calibrated: 3/23/2009 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN:1003 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 802.11b_ch6/Area Scan (5x5x1): Measurement grid: dx=15mm, dy=15mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.132 mW/g 802.11b_ch6/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 5.62 V/m; Power Drift = 0.391 dB Peak SAR (extrapolated) = 0.212 W/kg SAR(1 g) = 0.126 mW/g; SAR(10 g) = 0.092 mW/g Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.147 mW/g Date/Time: 2/18/2010 9:58:07 PM Test Laboratory: Compliance Certification Services Table Mode_Edge_Secondary Landscape DUT: Mitsumi; Type: NA; Serial: NA Communication System: 802.11bgn; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2437 MHz; σ = 2 mho/m; ε r = 53.9; ρ = 1000 kg/m 3 Phantom section: Flat Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV4 - SN3686; ConvF(6.48, 6.48, 6.48); Calibrated: 3/23/2009 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN:1003 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 802.11b_ch6/Area Scan (9x7x1): Measurement grid: dx=15mm, dy=15mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.048 mW/g 802.11b_ch6/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 3.89 V/m; Power Drift = 0.254 dB Peak SAR (extrapolated) = 0.065 W/kg SAR(1 g) = 0.046 mW/g; SAR(10 g) = 0.036 mW/g Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.053 mW/g Date/Time: 2/18/2010 10:29:36 PM Test Laboratory: Compliance Certification Services Table Mode_Edge_Secondary Portrait DUT: Mitsumi; Type: NA; Serial: NA Communication System: 802.11bgn; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 2437 MHz; σ = 2 mho/m; ε r = 53.9; ρ = 1000 kg/m 3 Phantom section: Flat Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV4 - SN3686; ConvF(6.48, 6.48, 6.48); Calibrated: 3/23/2009 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN:1003 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 802.11b_ch6/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.035 mW/g 802.11b_ch6/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 1.69 V/m; Power Drift = 0.682 dB Peak SAR (extrapolated) = 0.069 W/kg SAR(1 g) = 0.030 mW/g; SAR(10 g) = 0.014 mW/g Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.042 mW/g

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR Wi-Fi WIN CARD MODEL NUMBER: 0201JVA FCC ID: EW4-0201JVA REPORT NUMBER: 10J13061-1, Revision B ISSUE DATE: MARCH 08, 2010 Prepared for MITSUMI ELECTRIC CO., LTD. 1601, SAKAI ATSUGI-SHI KANAGAWA, JAPAN, 243-8533 Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 10J13061-1B DATE: MARCH 08, 2010 EUT: Wi-Fi WIN CARD FCC ID: EW4-0201JVA Page 2 of 82 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- 02/17/2010 Initial Issue T. Chan A 03/02/2010 Removed IC ID / RSS standard T. Chan B 03/08/2010 Changed EUT Description and revised FCC ID A. Zaffar REPORT NO: 10J13061-1B DATE: MARCH 08, 2010 EUT: Wi-Fi WIN CARD FCC ID: EW4-0201JVA Page 3 of 82 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................... 5 2. TEST METHODOLOGY ........................................................................................................ 6 3. FACILITIES AND ACCREDITATION.................................................................................... 6 4. CALIBRATION AND UNCERTAINTY .................................................................................. 6 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................... 6 4.2. SAMPLE CALCULATION.............................................................................................. 6 4.3. MEASUREMENT UNCERTAINTY................................................................................ 6 5. EQUIPMENT UNDER TEST ................................................................................................. 7 5.1. DESCRIPTION OF EUT................................................................................................ 7 5.2. MAXIMUM OUTPUT POWER....................................................................................... 7 5.3. DESCRIPTION OF AVAILABLE ANTENNAS............................................................... 7 5.4. SOFTWARE AND FIRMWARE..................................................................................... 7 5.5. WORST-CASE CONFIGURATION AND MODE .......................................................... 7 5.6. DESCRIPTION OF TEST SETUP................................................................................. 8 5.6.1. Radiated Emissions............................................................................................... 8 5.6.2. Line Conducted Emissions .................................................................................. 10 6. TEST AND MEASUREMENT EQUIPMENT ....................................................................... 12 7. ANTENNA PORT TEST RESULTS .................................................................................... 13 7.1. 802.11b MODE............................................................................................................ 13 7.1.1. 6 dB BANDWIDTH .............................................................................................. 13 7.1.2. 99% BANDWIDTH .............................................................................................. 16 7.1.3. OUTPUT POWER ............................................................................................... 19 7.1.4. AVERAGE POWER ............................................................................................ 23 7.1.5. POWER SPECTRAL DENSITY .......................................................................... 24 7.1.6. CONDUCTED SPURIOUS EMISSIONS............................................................. 27 7.2. 802.11g MODE IN THE 2.4 GHz BAND...................................................................... 33 7.2.1. 6 dB BANDWIDTH .............................................................................................. 33 7.2.2. OUTPUT POWER ............................................................................................... 37 7.2.3. AVERAGE POWER ............................................................................................ 41 7.2.4. POWER SPECTRAL DENSITY .......................................................................... 42 7.2.5. CONDUCTED SPURIOUS EMISSIONS............................................................. 46 8. RADIATED TEST RESULTS .............................................................................................. 53 8.1. LIMITS AND PROCEDURE ........................................................................................ 53 8.1.1. TRANSMITTER ABOVE 1 GHz FOR 802.11b MODE IN THE 2.4 GHz BAND .. 54 8.1.2. TRANSMITTER ABOVE 1 GHz FOR 802.11g MODE IN THE 2.4 GHz BAND .. 63 8.2. WORST-CASE BELOW 1 GHz................................................................................... 72 9. AC POWER LINE CONDUCTED EMISSIONS ................................................................... 75 REPORT NO: 10J13061-1B DATE: MARCH 08, 2010 EUT: Wi-Fi WIN CARD FCC ID: EW4-0201JVA Page 4 of 82 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 10. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................ 78 11. SETUP PHOTOS ......................................................................................................…

Text truncated - open the document above for the full version.

REPORT NO: 10J13061-1B DATE: MARCH 08, 2010 EUT: Wi-Fi WIN CARD FCC ID: EW4-0201JVA Page 80 of 82 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 11. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO REPORT NO: 10J13061-1B DATE: MARCH 08, 2010 EUT: Wi-Fi WIN CARD FCC ID: EW4-0201JVA Page 81 of 82 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. RADIATED RF MEASUREMENT SETUP RADIATED FRONT PHOTO RADIATED BACK PHOTO REPORT NO: 10J13061-1B DATE: MARCH 08, 2010 EUT: Wi-Fi WIN CARD FCC ID: EW4-0201JVA Page 82 of 82 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP END OF REPORT LINE CONDUCTED FRONT PHOTO LINE CONDUCTED BACK PHOTO