G8JHHI01VRT Hand Held Interrogator

Rhein Tech Laboratories, Inc. Report #: 2004234 360 Herndon Parkway FCC ID: G8JHHI01 Suite 1400 Model #: 52808G505 Herndon, VA 20170 Standard: FCC Part 90 http://www.rheintech.com Date: January 24, 2005 . Page 37 of 41 APPENDIX K: USER’S MANUAL Please refer to the Operator’s Manual. Copyright © 2004 AMCO Automated Systems All Rights reserved Rev A U U U S S S E E E R R R G G G U U U I I I D D D E E E TRACE ® T T r r a a c c e e I I n n t t e e r r r r o o g g a a t t o o r r V V R R T T ( ( T T I I V V R R T T ) ) f f o o r r W W i i n n d d o o w w s s C C E E D D R R A A F F T T TRACE INTERROGATOR VRT (CE) OPERATIONS Trace Interrogator VRT (CE) - User Guide AMCO Automated Systems P/N 52808T510 Rev. A, December 15, 2004 Introduction ...................................................... 4 System Requirements ..................................... 5 Hardware Requirements ........................................................... 5 Software Requirements ............................................................ 5 Warnings.................................................................................... 5 TI VRT CE Operation ................................................................. 5 Conventions ..................................................... 5 <Esc> ......................................................................................... 6 <Enter>....................................................................................... 6 <Up Arrow>, <Down Arrow>.................................................... 6 <Tab> ......................................................................................... 6 Message Box <Yes> <NO> ....................................................... 6 TIV Screens ...................................................... 7 Login .......................................................................................... 7 Main (D)...................................................................................... 7 Route Selection (D) ................................................................... 7 Communications (D) ................................................................. 8 Data Entry .................................................................................. 8 Exit TI VRT CE ........................................................................... 8 Account Navigation and Data Entry............... 9 Navigation.................................................................................. 9 <Esc>..............................................................................................9 <Enter> .........................................................................................10 <Up Arrow>, <Down Arrow> ......................................................10 Jumps ...................................................................................... 10 Jump to the Previous Route .......................................................10 Jump to Beginning of Current Route.........................................10 Jump to End of Current Route ...................................................10 Jump to Next Unread Interrogation ...........................................10 Jump to Specified Sequence Number .......................................11 Jump to Next Unread Account in the Current Route................11 Jump to Next Route.....................................................................11 TRACE INTERROGATOR VRT (CE) OPERATIONS Trace Interrogator VRT (CE) - User Guide AMCO Automated Systems P/N 52808T510 Rev. A, December 15, 2004 Searches .................................................................................. 11 Information Displays............................................................... 12 Help / Available Commands Display..........................................12 Route Selection Display..............................................................12 Route Summary Display .............................................................13 Configuration Display .................................................................13 Display VRT Requests Details....................................................13 Trouble Code Display..................................................................14 Messages Display........................................................................15 Error Log Display ........................................................................15 Data Entry operations ............................................................. 16 Manual Index Read ......................................................................16 Clear Index Read .........................................................................17 Force Unattempted Account ......................................................17 Adding a Trouble Code ...............................................................17 Adding / Editing a Text Message................................................18 Setting the Re-sequence Flag ....................................................19 Single RF Index Read..................................................................20 Multiple Parameter RF Read .......................................................21 Single History / TOU RF Read ....................................................22 General Index RF Read ...............................................................22 TI VRT CE Communication with Route Manager VRT .................................................. 23 Establishing communications................................................ 23 Uploading Routes from RM VRT to TI VRT(CE) .................... 25 Downloading data From TI VRT(CE) to RM VRT ................... 26 Removing Route From TI VRT (CE) ....................................... 26 Updating Handheld files ......................................................... 26 Hot keys .......................................................... 28 Troubleshooting...............…

Text truncated - open the document above for the full version.

Copyright © 2004 AMCO Automated Systems All Rights reserved Rev A U U U S S S E E E R R R G G G U U U I I I D D D E E E TRACE ® T T r r a a c c e e I I n n t t e e r r r r o o g g a a t t o o r r V V R R T T ( ( T T I I V V R R T T ) ) f f o o r r W W i i n n d d o o w w s s C C E E D D R R A A F F T T TRACE INTERROGATOR VRT (CE) OPERATIONS Trace Interrogator VRT (CE) - User Guide AMCO Automated Systems P/N 52808T510 Rev. A, December 15, 2004 Introduction ...................................................... 4 System Requirements ..................................... 5 Hardware Requirements ........................................................... 5 Software Requirements ............................................................ 5 Warnings.................................................................................... 5 TI VRT CE Operation ................................................................. 5 Conventions ..................................................... 5 <Esc> ......................................................................................... 6 <Enter>....................................................................................... 6 <Up Arrow>, <Down Arrow>.................................................... 6 <Tab> ......................................................................................... 6 Message Box <Yes> <NO> ....................................................... 6 TIV Screens ...................................................... 7 Login .......................................................................................... 7 Main (D)...................................................................................... 7 Route Selection (D) ................................................................... 7 Communications (D) ................................................................. 8 Data Entry .................................................................................. 8 Exit TI VRT CE ........................................................................... 8 Account Navigation and Data Entry............... 9 Navigation.................................................................................. 9 <Esc>..............................................................................................9 <Enter> .........................................................................................10 <Up Arrow>, <Down Arrow> ......................................................10 Jumps ...................................................................................... 10 Jump to the Previous Route .......................................................10 Jump to Beginning of Current Route.........................................10 Jump to End of Current Route ...................................................10 Jump to Next Unread Interrogation ...........................................10 Jump to Specified Sequence Number .......................................11 Jump to Next Unread Account in the Current Route................11 Jump to Next Route.....................................................................11 TRACE INTERROGATOR VRT (CE) OPERATIONS Trace Interrogator VRT (CE) - User Guide AMCO Automated Systems P/N 52808T510 Rev. A, December 15, 2004 Searches .................................................................................. 11 Information Displays............................................................... 12 Help / Available Commands Display..........................................12 Route Selection Display..............................................................12 Route Summary Display .............................................................13 Configuration Display .................................................................13 Display VRT Requests Details....................................................13 Trouble Code Display..................................................................14 Messages Display........................................................................15 Error Log Display ........................................................................15 Data Entry operations ............................................................. 16 Manual Index Read ......................................................................16 Clear Index Read .........................................................................17 Force Unattempted Account ......................................................17 Adding a Trouble Code ...............................................................17 Adding / Editing a Text Message................................................18 Setting the Re-sequence Flag ....................................................19 Single RF Index Read..................................................................20 Multiple Parameter RF Read .......................................................21 Single History / TOU RF Read ....................................................22 General Index RF Read ...............................................................22 TI VRT CE Communication with Route Manager VRT .................................................. 23 Establishing communications................................................ 23 Uploading Routes from RM VRT to TI VRT(CE) .................... 25 Downloading data From TI VRT(CE) to RM VRT ................... 26 Removing Route From TI VRT (CE) ....................................... 26 Updating Handheld files ......................................................... 26 Hot keys .......................................................... 28 Troubleshooting............................................. 29 TRACE INTERROGATOR VRT (CE) OPERATIONS Trace Interrogator VRT (CE) - User Guide AMCO Automated Systems P/N 52808T510 Rev. A, December 15, 2004 Introduction Copyright © 2004 AMCO Automated Systems. All Rights Reserved The contents of this document are…

Text truncated - open the document above for the full version.

February 2, 2005 American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 Although this device adheres to the PCMCIA standards, user operation in a laptop PC is prohibited by the absence of both a required device driver and required application software. Physically installing this device into a laptop PC would result in an “UNKNOWN DEVICE” error. Sincerely, Thomas J. Wack Sr. Digital/Analog Engineer [email protected] AMCO Automated Systems, LLC 107 Erskine Lane Scott Depot, WV 25560 (304) 757-3300 Fax (304) 757-3388

Rhein Tech Laboratories, Inc. Report #: 2004234 360 Herndon Parkway FCC ID: G8JHHI01 Suite 1400 Model #: 52808G505 Herndon, VA 20170 Standard: FCC Part 90 http://www.rheintech.com Date: January 24, 2005 . Page 29 of 41 APPENDIX C: CONFIDENTIALITY REQUEST LETTER Please see the following page. January 25, 2005 American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: To Whom It May Concern: The following information is to be held confidential pursuant of 47 CFR Part 0 §0.459 and Section 552(b)(4) of the Freedom of Information Act, because the information provided contains trade secrets and is proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. • Schematics • Technical Product Description • Block Diagram • Parts List (BOM) • Adjustment Procedure Sincerely, Thomas J. Wack Sr. Digital/Analog Engineer [email protected] AMCO Automated Systems, LLC 107 Erskine Lane Scott Depot, WV 25560 (304) 757-3300 Fax (304) 757-3388

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 January 30, 2005 RE: FCC ID: G8JHHI01_ATCB002119 Attention: Kathy Grzovic I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please note that the documentation states that this device is a PCMCIA card that goes into a hand held device. However, as this is a PCMCIA card the possibility exists that the user may put this into a laptop computer. If this device can operate in a laptop computer SAR measurements may be required. Please provide evidence that this device cannot operate in a laptop PC. (i.e. is the device protected by software etc?) 2. Please note that the manual states that the operating frequency of the device is 450 4o 460 Hz. This should be MHz. Please correct the manual to reflect the proper operating frequency range of the device. 3. Please note that the manual does not appear to address the FCC rf exposure requirements. Please provide a manual that properly addresses the rf exposure requirements of the device. This would necessarily include the mandatory 24cm minimum separation warning and the warning about not collocating the antenna. 4. Please note that the report (page 1) states the device is a TNF – Licensed Non-Broadcast Transmitter Held to Face. IF this is in a device that is held to the face and if the transmitter can transmit in that position, it may require SAR as it is over the power in the exclusions list. If the device cannot transmit in the face held position please explain how this is accomplished. Please explain and please verify why SAR is or is not required for this device. 5. Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 January 30, 2005 RE: FCC ID: G8JHHI01_ATCB002119 Attention: Kathy Grzovic I have a few comments on this Application. Please note that further comments may arise in response to answers provided to the questions below. 1. Please note that the documentation states that this device is a PCMCIA card that goes into a hand held device. However, as this is a PCMCIA card the possibility exists that the user may put this into a laptop computer. If this device can operate in a laptop computer SAR measurements may be required. Please provide evidence that this device cannot operate in a laptop PC. (i.e. is the device protected by software etc?) Response: Please refer to the attestation uploaded with this response. 2. Please note that the manual states that the operating frequency of the device is 450 - 460 Hz. This should be MHz. Please correct the manual to reflect the proper operating frequency range of the device. Response: Please refer to the revised manual exhibit uploaded with this response. 3. Please note that the manual does not appear to address the FCC rf exposure requirements. Please provide a manual that properly addresses the rf exposure requirements of the device. This would necessarily include the mandatory 24cm minimum separation warning and the warning about not collocating the antenna. Response: Please refer to page 5 of the manual (page 6 of the manual exhibit) for the RF exposure statement. 4. Please note that the report (page 1) states the device is a TNF – Licensed Non-Broadcast Transmitter Held to Face. IF this is in a device that is held to the face and if the transmitter can transmit in that position, it may require SAR as it is over the power in the exclusions list. If the device cannot transmit in the face held position please explain how this is accomplished. Please explain and please verify why SAR is or is not required for this device. Response: Please excuse the typographical error, and refer to the revised report uploaded with this response. Dennis Ward mailto:[email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

Rhein Tech Laboratories, Inc. Report #: 2004234 360 Herndon Parkway FCC ID: G8JHHI01 Suite 1400 Model #: 52808G505 Herndon, VA 20170 Standard: FCC Part 90 http://www.rheintech.com Date: January 24, 2005 . Page 28 of 41 APPENDIX B: AGENCY AUTHORIZATION LETTER Please see the following page. January 20, 2005 American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 Re: Agent Authorization To Whom It May Concern: AMCO Automated Systems, LLC hereby authorizes Rhein Tech Laboratories, Inc. (RTL), 360 Herndon Parkway, Suite 1400, Herndon, VA 20170 to act as agent. APPLICANT ANTI-DRUG ABUSE CERTIFICATION: In signing this letter, Applicant certifies that, in the case of an individual applicant, he or she is not subject to a denial of federal benefits, that includes: FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a), or, in the case of a non-individual applicant. No party to the application is subject to a denial of federal benefits that includes FCC benefits, pursuant to that section. For the definition of a “party” for these purposes, see 47 CFR 1.2002(b). Sincerely, Thomas J. Wack Sr. Digital/Analog Engineer [email protected] AMCO Automated Systems, LLC 107 Erskine Lane Scott Depot, WV 25560 (304) 757-3300 Fax (304) 757-3388

To:William Graff [email protected] From:Tim Harrington [email protected] FCC Equipment Authorization Branch Re:FCC ID:G8JHHI01 Applicant:AMCO Automated Systems, LLC Correspondence Number: 18327 731 Confirmation Number: TC388170 Date of Original E-Mail:03/10/2005 Subject: audit 1) Please describe applicable 90 subpart K specific sections,e.g.,90.267. RESPONSE : AMCO Automated Systems maintains two licenses WPMC456 (Frequency used on a shared basis to engage in meter reading for Electric, Gas, and Water Companies. Radios will be used for automatic meter reading purposes.), and WNRV867 (AMCO is in the business of sales and marketing of electric, gas and water automatic utility meter reading devices and uses the frequencies for demonstrating meter reading devices to potential customers.). The application (and capability) of this device is non-voice, data only with an output power of 1 watt. 2) User manual states "The VRT HAND HELD Interrogator (HHI)transmitter is currently licensed by the FCC to operate at 450-460 MHz." Please explain how this is consistent with single frequency on Form731. RESPONSE : Please see the updated user manual uploaded with this response. 3) Please provide more info and/or photos or drawings about handheld "host"unit used for final installation/operation of this transmitter. RESPONSE : The “host” unit utilized is offered by DAP Technologies (www.daptech.com). The units are part of DAP Technologies MICROFLEX family, specifically the CE5000 Series. A replacement ‘nose’ cone was designed by AMCO Automated Systems to accommodate the radio system. Photographs have been uploaded as an external photograph exhibit. The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal pursuant to Section 2.917(c). DO NOT Reply to this email by using the Reply button.In order for your response to be processed expeditiously, you must upload your response via the Internet at www.fcc.gov,E-Filing,OET TCB/Accreditor Electronic Filing, TCB Login, Submit Correspondence. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender.

Engineering and Testing for EMC and Safety Compliance 360 Herndon Parkway Suite 1400 Herndon, VA 20170 Phone: 703-689-0368 Fax: 703-689-2056 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Subject: audit cont. FCC ID: G8JHHI01 Applicant: AMCO Automated Systems, LLC Correspondence Reference Number: 25671 731 Confirmation Number: TC388170 Date of Original Email: 01/11/2006 Subject: audit cont. TCB to address: regarding reply to corresp 18327 #3, please explain compliance with 47 CFR 2.925(d) Response : Please see the label exhibit and cover letter uploaded with this response.

January 24, 2005 American TCB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 cc: Kathy Grzovic, Rheintech Re: Audit of G8JHHI01 Equipment Authorization This letter and the attached drawings constitute our response to the FCC’s Audit of our Handheld Interrogator modular radio product, ID# G8JHHI01, in which we demonstrate our commitment to comply with the Commission’s rules. We now submit our response via Rheintech and American TCB. On the 11 th of January, 2006, Tim Harrington of the Commission’s Equipment Authorization Branch requested that AMCOAS demonstrate compliance with labeling requirements of 47 CFR 2.925(d). The correspondence Tim referenced concerned an equipment authorization grant label on the outside of the handheld computer (hereinafter: host device) that contains our modular radio card. We put a grantee label on the modular radio card itself, and intended to put one on the outside of the host device, but the photos in our final test report do not show the label on the outside of the host device. We regret the oversight. To rectify the situation, AMCOAS has modified our assembly drawings to show a grantee code label on the outside of the host device. A grantee code label will be applied to the host device by AMCOAS at the time the modular radio device is installed in the host device. We will send grantee labels with instructions to our customers for the 28 units we have in the field, and retrofit grantee labels on units that come to AMCOAS for repair. Attached to this letter is an AMCOAS released drawing showing the details of the label. Also attached is another drawing showing the assembly of the modular radio into the host device, including placement of the grantee code label. Sincerely, Steve Bragg Director of Engineering (Acting) FCC Point of Contact AMCO Automated Systems, LLC AMCO Automated Systems, LLC 208 South Rogers Lane Raleigh, NC 27610 (919) 250-5700 Fax (919) 250-5439 [email protected]

Rhein Tech Laboratories, Inc. Report #: 2004234 360 Herndon Parkway FCC ID: G8JHHI01 Suite 1400 Model #: 52808G505 Herndon, VA 20170 Standard: FCC Part 90 http://www.rheintech.com Date: January 24, 2005 . Page 40 of 41 APPENDIX M: EXTERNAL PHOTOGRAPHS PHOTOGRAPH 3: FRONT VIEW OF EUT

External Photographs of “Host” Unit Front View & Antenna Side View & Antenna Back View with Antenna

Rhein Tech Laboratories, Inc. Report #: 2004234 360 Herndon Parkway FCC ID: G8JHHI01 Suite 1400 Model #: 52808G505 Herndon, VA 20170 Standard: FCC Part 90 http://www.rheintech.com Date: January 24, 2005 . Page 32 of 41 APPENDIX F: LABEL AND LABEL LOCATION Please see the following page for a label sample, and its location on the back of the EUT.

11 22 A A B B THIS DEVICE CONTAINS: HANDHELD INTERROGATOR MODEL 52808K500-1 REV XX MM/DD/YY FCC ID: G8JHHI01 AMCO AUTOMATED SYSTEMS, LLC XXXXXXXX TITLE SIZE DWG NO REV SCALE SHEET OF DRAWNCHECKED QA MFG APPROVED 208 SOUTH ROGERS LANE RALEIGH, NC 27610TEL: 919 250-5700 FAX: 919 250-5439 AUTOMATED SYSTEMS, LLC MATERIAL TOLERANCES-UNLESS OTHERWISE SPECIFIEDINCHES ANGLES .X ` ` 1 ~ .XX ` .02" .XXX ` .005" SURFACES w min THIS DOCUMENT IS THE PROPERTY OF AMCO AUTOMATED SYSTEMS, ANDIT'S SUBSTANCE IS CONFIDENTIAL AND PROPRIETARY. THE CONTENTSHEREOF SHALL NOT BE PUBLISHED OR DISCLOSED TO OUTSIDE PARTIESOR USED FOR THEIR BENEFIT WITHOUT THE WRITTEN AUTHORIZATION OFAMCO AUTOMATED SYSTEMS. OLD DWG #N.A. DRAWING RELEASE ECN #: REV DESCRIPTION DATE LABEL, FCC, S/N, HHI 11802P043 1 1 0 A STamar 1/18/2006 JC 10/19/2005 MATERIAL: WHITE 3 MIL POLYESTER (TT700)ADHESIVE: ACRYLICCOLORS: BLACK COPY ON WHITE BACKGROUNDMAN: IDENTCO SEE NOTES 0 RELEASED FOR PRODUCTION 957 01/18/06 BAR CODE AREA(DERIVED FROM S/N) PART NUMBER AND REVLEVEL PER BOM DATE OF FINAL ASSEMBLY(MONTH/DAY/YEAR) HHI SERIAL #(MIN TEXT HEIGHT .10) LINE # KIT P/N HANDHELD P/N DESCRIPTION 1 52808K500-1 40808G007 ETHERNET DAP COLOR CE5240 HANDHELD COMPUTER 2 52808K500-2 3 52808K500-3 4 52808K500-4 TABLE 1: KIT PART NUMBERS AND HANDHELD DESCRIPTION 11 22 33 44 A A B B TITLE SIZE DWG NO REV SCALE SHEET OF DRAWNCHECKED QA MFG APPROVED 208 SOUTH ROGERS LANE RALEIGH, NC 27610TEL: 919 250-5700 FAX: 919 250-5439 AUTOMATED SYSTEMS, LLC MATERIAL TOLERANCES-UNLESS OTHERWISE SPECIFIEDINCHES ANGLES .X ` ` 1 ~ .XX ` .02" .XXX ` .005" SURFACES w min THIS DOCUMENT IS THE PROPERTY OF AMCO AUTOMATED SYSTEMS, ANDIT'S SUBSTANCE IS CONFIDENTIAL AND PROPRIETARY. THE CONTENTSHEREOF SHALL NOT BE PUBLISHED OR DISCLOSED TO OUTSIDE PARTIES OR USED FOR THEIR BENEFIT WITHOUT THE WRITTEN AUTHORIZATION OFAMCO AUTOMATED SYSTEMS. OLD DWG #N.A. DRAWING RELEASE ECN #: REV DESCRIPTION DATE KIT, HANDHELD, DAP 52808K500 1 1 6 B PPenn 11/17/2004 SM 1/13/2005 TW 1/14/2005 AMCO 1 1 52808G505 ASSEMBLY, CARD, PCMCIA, RF, HANDHELD 2 1 52808G500 ASSEMBLY, NOSECAP, MODULE, RF, HANDHELD, DAP 3 1 SEE TABLE 1 COMPUTER, HANDHELD 4 1 10102G001 NOSECAP FOAM FOR CE W/CABLE CUT 5 2 52805P003 GRAY VANDAL PLUG 6 1 11802P040 ANTENNA WARNING LABEL 7* 1 52808G303 ANTENNA,SEALED CONNECTOR 8* 1 52808G520 CD, TIVRTCE INSTALLATION SOFTWARE 9* 1 12001P010 BOX, CARDBOARD, w/INSERT 10 1 11802P043 LABEL, FCC, S/N, HHI Parts List ITEM QTY PART NUMBER DESCRIPTION NOTES: 1. REMOVE DAP BATTERY. DETACH INSULATING DECAL FROM THE BATTERY TERMINALS. RE-INSTALL BATTERY. 2. INSERT PCMCIA CARD (2) INTO HANDHELD 3. INSERT NOSECAP FOAM (4) AS SHOWN MAKING SURE THE ANTENNACABLE CLEARS THE FOAM. 4. ATTACH WARNING LABEL (6) AND FCC LABEL (10) AS SHOWN MAKING SURE ALL EDGES OF LABELS ARE SECURED TO THE NOSECAP. 5. ATTACH ANTENNA CABLE ON NOSECAP (1) TO PC MCIA CARD (2) PRIOR TO ATTACHMENT TO HANDHELD. MAKE SURE THAT THE ANTENNA CABLE PLUG IS FULLY INSERTED INTO THE JACK ON THE PCMCIA CARD. 6. SECURE NOSECAP TO HANDHELDBY TIGHTENING SCREWS ON NOSECAP. TIGHTEN SCREWS PER TORQUE SPECIFICATION DOCUMENT 40702T010. 7. PERFORM SYSTEM CHECK PER AMCOAS DOCUMENT 52870T505. 8. ** PRESS IN VANDAL PLUG (5) ONLY AFTER ALL SYSTEM CHECKS HAVE BEEN COMPLETE** 9. PLACE UNIT IN BOX (9) THEN PLACE CD (8) AND ANTENNA (7) IN ORDER ON TOP OF UNIT AND SECURE BOX. *NOT SHOWN 2 1 860 0 01/14/05 RELEASED FOR PRODUCTION ADD ITEMS 4,5 & 6PER ECN 883 1 6 08/16/05 2 ADD NOTE 1 PER ECN 912 10/05/05 5 3 REPLACE ANTENNA CONNECTOR CABLE ASSY ON52808G500 PER ECN 928 10/19/05 4 ADD TORQUE SPECIFICATIONS TO NOTE 6PER ECN 922 10/19/05 5 12/14/05 CHANGED ITEM 7 FROM 52805P303 TO 52808G303 PER ECN 944 4 10 3 6 ADD ITEM 10 - FCC LABEL PER ECN 957 01/18/06 6

Rhein Tech Laboratories, Inc. Report #: 2004234 360 Herndon Parkway FCC ID: G8JHHI01 Suite 1400 Model #: 52808G505 Herndon, VA 20170 Standard: FCC Part 90 http://www.rheintech.com Date: January 24, 2005 . Page 32 of 41 APPENDIX F: LABEL AND LABEL LOCATION Please see the following page for a label sample, and …

Text truncated - open the document above for the full version.