G9B-210193Dielectric Resonator Oscillator

Jean-Pierre LERUTH Print : 09/03/2012 Page 1 / 3 File : 4.BEA-T1B User Guide.doc B.E.A. K-Band Transceiver 21.0193 (BEA-T1B) User Guide History : Date Author Version 2011/12/06 First release JPL 1.00 2012/01/19 Instructions for OEM integrator JPL 1.01 2012/03/09 Additional instructions for OEM integrator JPL 1.02 FCC ID : G9B-210193 IC ID : 4680A-210193 BEA Inc. (Bureau d’Electronique Appliquée) 100 Enterprise Drive, RIDC Park West Pittsburgh, PA 15275, USA Phone: (412) 249 4100 Jean-Pierre LERUTH Print : 09/03/2012 Page 2 / 3 1. Functional description of BEA-T1B Transceiver. The DRO module P/N, 21.0193 consists of a 24.150GHz Microwave Transceiver and is used in Doppler movement detectors. 2. Electrical specifications. Output frequency : Output power : 24.125 GHz ± 50 MHz < 20 dBm Type of modulation : Continuous wave ASK modulation : none Operating voltage 5 V dc ±5% Operating current <35mA typ. Frequency Drift vs Temperature Change : < 1 MHz / °C Operating temperature range : -30 °C to +70 °C 3. Pin arrangement. (Single row pin header) Pin I/O Description 1 Supply voltage Vcc 2 Output signal IF 3 Ground GND Jean-Pierre LERUTH Print : 09/03/2012 Page 3 / 3 4. Regulatory Compliance • This device has been tested and approved to be compliant with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: (1) This device may not cause harmful interferences, and (2) This device must accept any interference received, including interference that may cause undesired operation. 4.1 FCC & IC Instructions • Changes or modifications made to the equipment not expressly approved by BEA Inc. may void the FCC authorization to operate this equipment. • The use of the BEA-T1B transceiver is authorized into mobile or fixed devices taking into account the conditions listed below : (1) OEM Integrator may be sure that the end user manual may not contain any information about the way to install or remove the module from the final product. (2) The following information is required to be incorporated in the user manual of the final system: - This device has been tested and approved to comply with Part 15B unintentional radiator requirements - The antenna of the module may not be removed, replaced nor modified. The antenna must not be co-located or operating in conjunction with any other antenna or transmitter. No additional antenna must be used. - This device may not cause harmful interferences, and this device must accept any interference received, including interference that may cause undesired operation. (3) The module must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. (4) Power supply of the module must be conform to the electrical specifications as described in § 2 of the current user manual. (5) The antenna of the module may not be removed, replaced nor modified. The antenna must not be co-located or operating in conjunction with any other antenna or transmitter. No additional antenna must be used. (6) OEM integrator is responsible for ensuring that after the module is installed and operational into the host, it continues to be compliant with the Part 15B unintentional radiator requirements. (7) A label with the words ‘Contains FCC ID:G9B-210193’ and ‘Contains IC:4680A- 210193’ shall be applied and visible from the outside of the end product.

OPEN U P Jean-Pierre LERUTH Print : 15/12/2011 File : 8.BEA-T1B Confidentiality.doc Date : 06/12/2011 CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Miils Road Columbia, MD 21048 December, 15 2011 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission”s Rules (47 C.F.R.) and Section §552(b)(4) 0f the Freedom of Information Act, B.E.A. Inc. (Bureau d’Electronique Appliquée) request confidentiality for the following products FCC ID Number Product Title f Model G9B-210193 BEA Dielectric Resonator Oscillator / BEA-T1B For the product stated above, we request that the following information be held confidential: 1. Circuit diagrams, BOM, and PCBs Electronic File : ‘BEA-T1B Schematics’. 2. Blockdiagram Electronic File : ‘BEA-T1B Blockdiagram’. 3. Operational description Electronic File : ‘BEA-T1B Operational description’. The above exhibits contain B.E.A. Inc. trade secrets and proprietary information that could be cf benefit to our competitors regarding the design of our sensors. This material is not available to the general public and we request that it be withheld form public inspection. If you have any questions, please feel free to contact me at the address shown below. Sincerely, B.E.A. Inc. Randy Wickman 100 Enterprise Drive, RIDC Park West Pittsburgh, PA 15275, USA Phone: (412) 249 4100 Email: rwwickman@’beainc.com A HALMA COMPANY Page 1 / 1

Jean-Pierre LERUTH Print : 19/01/2012 Page 1 / 1 File : 9.BEA-T1B Modular Approval.doc Date : 06/12/2011 21.0193 (BEA-T1B) Modular Approval Information FCC ID: G9B-210193 Requirements for equipment authorization: 1. The BEA-T1B Transceiver module working in the 24GHz frequency band has its own RF shielding. It has been designed and tested to comply with Part 15 of the Commission’s Rules without any additional shielding. 2. The BEA-T1B Transceiver module has no internal power regulation. The specifications of the power circuitry into which the module is installed are listed in the ‘installation instructions’. 3. The antenna is an integrated part of the module and cannot be removed nor replaced. 4. The BEA-T1B Transceiver module has been tested as a standalone module with power supply as specified into the datasheets. A report from a accredited laboratory is available. 5. The BEA-T1B Transceiver module has its own label and the device into which the module is installed will receive a label with the words : ‘Contains FCC ID:G9B-210193’ 6. When used in conformity with the ‘installation instructions’, the BEA-T1B Transceiver module will operate in compliance with section 15.245. 7. The BEA-T1B Transceiver module complies with any other applicable RF exposure requirements.

Jean-Pierre LERUTH Print : 15/12/2011 Page 1 / 2 File : 7.BEA-T1b Pictures.doc Date : 06/12/2011 B.E.A. Dielectric Resonator Oscillator : 21.0193 (BEA-T1B) Pictures of the DRO External picture : front view External picture : rear view Jean-Pierre LERUTH Print : 15/12/2011 Page 2 / 2 Internal picture

Jean-Pierre LERUTH Print : 13/01/2012 Page 1 / 1 File : 5.BEA-T1B Labelling.doc Date : 13/01/2012 B.E.A. Dielectric Resonator Oscillator 21.0193 (BEA-T1B) Labelling information

Jean-Pierre LERUTH Print : 15/12/2011 Page 1 / 2 File : 7.BEA-T1b Pictures.doc Date : 06/12/2011 B.E.A. Dielectric Resonator Oscillator : 21.0193 (BEA-T1B) Pictures of the DRO External picture : front view External picture : rear view Jean-Pierre LERUTH Print : 15/12/2011 Page 2 / 2 Internal picture

2012-03-12 Page 1 of 32 TEST REPORT Test report no.: 1-3880/11-01-02-B Testing laboratory Applicant CETECOM ICT Services GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.cetecom.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12076-01-01 Area of Testing: Radio/Satellite Communications B.E.A. S.A. 5 Allée des Noisetiers Parc Scientifique du Sart-Tilman 4031 Angleur / BELGIUM Fax: -- Contact: Mr. Jean-Pierre LERUTH e-mail: [email protected] Phone: +32 43 61 68 68 Manufacturer Same as applicant Test standard/s 47 CFR Part 15 Title 47 of the Code of Federal Regulations; Chapter I-Federal Communications Commission Subchapter A – general, Part 15 Radio frequency devices RSS – 210 Issue 8 Spectrum Management and Telecommunications – Radio Standards Specification Low-power Licence-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: 24 GHz radar system Model name: BEA-T1B, mono, 3x1 Frequency: 24.075 GHz – 24.175 GHz FCC ID: IC: G9B-210193 4680A-210193 Power Supply: 5 V DC ±5% Temperature Range: -30 °C to +70 °C Test report authorised: Test performed: 2012-03-12 Karsten Geraldy 2012-03-12 René Oelmann Test report no.: 1-3880/11-01-02-B 2012-03-12 Page 2 of 32 1 Table of contents 1 Table of contents ............................................................................................................................................ 2 2 General information ....................................................................................................................................... 3 2.1 Notes ..................................................................................................................................................... 3 2.2 Application details ............................................................................................................................... 3 3 Test standard/s ............................................................................................................................................... 3 4 Test environment ............................................................................................................................................ 3 5 Test item .......................................................................................................................................................... 4 6 Test laboratories sub-contracted ................................................................................................................. 4 7 Summary of measurement results ............................................................................................................... 5 8 RF measurement testing ............................................................................................................................... 6 8.1 Description of test setup .................................................................................................................... 6 8.1.1 Radiated measurements............................................................................................................. 6 8.1.2 Additional comments .................................................................................................................. 7 8.2 RSP100 test report cover sheet / performance test data ................................................................ 8 9 Measurement results ...................................................................................................................................... 9 9.1 Field strength of emissions (wanted signal) .................................................................................... 9 9.2 Occupied bandwidth (99% bandwidth) ........................................................................................... 11 9.3 Field strength of emissions (radiated spurious) ............................................................................ 13 9.4 Conducted spurious emissions < 30 MHz ...................................................................................... 21 10 Test equipment and ancillaries used for tests ................................................................................... 23 Annex A Photographs of the test setup ...................................................................................................... 24 Annex B External photographs of the EUT ................................................................................................. 27 Annex C Document history .......................................................................................................................... 32 Annex D Further information ........................................................................................................................ 32 Test report no.: 1-3880/11-01-02-B 2012-03-12 Page 3 of 32 2 General information 2.1 Notes The test results of this test report relate exclusively to the test item specified in this test report. CETECOM ICT Services GmbH does not assume responsibility for any conclusions and generalisations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of CETECOM ICT Services GmbH. This test report is electronically signed and valid without handwriting signature. For verification of the electro…

Text truncated - open the document above for the full version.

Test report no.: 1-3880/11-01-02-B 2012-03-12 Page 24 of 32 Annex A Photographs of the test setup Photo 1: Photo 2: Test report no.: 1-3880/11-01-02-B 2012-03-12 Page 25 of 32 Photo 3: Photo 4: Test report no.: 1-3880/11-01-02-B 2012-03-12 Page 26 of 32 Photo 5: