HN2-BTM311BTM311

PRELIMINARY DRAFT P/N 074476-001 Note: You only need to read this information if your Intermec product has a Bluetooth™ compatible module from Actiontec ® Electronics. Important BTM311 Bluetooth Radio Information! Contents For Users in the United States and Canada..................................................2 For Users Outside of the United States and Canada.....................................3 Pour les utilisateurs en dehors du Canada et des Etats-unis..........................5 Für Benutzer außerhalb von Kanada und den Vereinigten Staaten...............6 Per gli utenti al di fuori del Canada o degli Stati Uniti.................................7 Para Usuarios Fuera de Canada o de los Estados Unidos..............................8 Para Usuários Fora do Canadá ou dos Estados Unidos .................................9 .....................................................9 For Users in the United States and Canada Place this supplement in your manual. This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that can cause undesired operation. Federal Communications Commission Compliance FCC Digital Emissions Compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio or television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Changes or modifications not expressly approved by Intermec could void the user’s authority to operate this equipment. 2 PRELIMINARY DRAFT This radio meets the FCC RF exposure guidelines when used with the Intermec accessories supplied or designated for this product. Use of other accessories may not ensure compliance with the FCC RF exposure guidelines. Specific Absorption Rate, or SAR, is a measurement of radio frequency energy. This radio is categorically exempt from routine SAR evaluation. The FCC excludes radios from routine SAR evaluation if the maximum peak power is less than 24.5 mW. The maximum peak power for this radio, as measured using corresponding FCC requirements, is 13.8 mW. Use of any other transmitting devices within 20 cm (8 in) of this radio could void the user’s authority to operate this equipment. For Users Outside of the United States and Canada Place this supplement in your manual. The Intermec product you purchased transmits and receives data using a 2.4 GHz Frequency Hopping Spread Spectrum system. Programming and configuration information for the transceivers is also provided in the host device documentation. Please check the Intermec web site for additional documentation at www.intermec.com. Hereby, Intermec Technologies Corporation declares that this Bluetooth module is in compliance with the essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC). This product has been assessed to the following standards: • ETSI EN 300 328-2 v1.2.1 (2001-12) • ETSI EN 301 489-17 v1.2.1 (2002-08) • EN 60950:1992 (incl. Amdt. 1-4, 11) PRELIMINARY DRAFT 3 The transmitter module’s output power is 13.8 mW. The products using this module are intended for business and industrial environments. They should not be used in residential environments and by children. 0981 This product is marked with this logo and uses radio frequency bands that are harmonized throughout the European Community. The following table indicates the areas of intended use of the equipment and any known restrictions. Country of License Intended Use Yes No Required Restrictions Details Austria X Belgium X Cyprus X Czech Republic X Denmark X Estonia X Finland X France X Germany X Greece X Hungary X Ireland X Italy X Lithuania X Latvia X Luxembourg X Malta X The Netherlands X Poland X Portugal X Slovakia X Slovenia X Spain X Sweden X United Kingdom X 4 PRELIMINARY DRAFT Country of License Intended Use Yes No Required Restrictions Details Other non-EU: China X Iceland X Liechtenstein X Norway X Switzerland X Japan X Additional EMI/RFI Compliance This device meets the Class B limit requirements of CISPR 22. Pour les utilisateurs en dehors du Canada et des Etats-unis Veuillez placer ce supplément dans votre manuel. Le produit Intermec que vous avez acheté peut transmettre et recevoir des données à l’aide d’un système d’étalement du spectre en bond de fréquence de 2,4 GHz. Les informations de programmation et de configuration pour les émetteurs-récepteurs sont également fournies dans la documentation de l’appareil hôte. Pour obtenir toute documentation supplémentaire, veuillez consulter le site web d’Intermec, à l’adresse www.intermec.com. Par la présente, Intermec Technologies Corporation déclare que ce Bluetooth radio est conforme aux exigences de base et autres exigences pertinentes de la Directive R&TTE (1999/5/EC). Ce produit a été évalué par rapport aux normes suivantes: • ETSI EN 300 328-2 v1.2.1 (2001-12) • ETSI EN 301 489-17 v1.2.1 (2002-08) • EN …

Text truncated - open the document above for the full version.

October 12, 2004 To Who It May Concern: Intermec Technologies Corporation, the undersigned, hereby authorizes Northwest EMC, Inc., to act on our behalf, as our agent, in the following matters related to the FCC and Industry Canada approval of our products: report submittal, related correspondence, the signing of all documents related to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by Northwest EMC, Inc. within the scope of this authorization shall have the same affect as our own. This authorization shall expire 12 months from original date. If you have any questions regarding this application, please feel free to contact me via phone at 425-356-1765, via fax at 425-348-2633 or via email at [email protected]. Sincerely, Katie Molina Compliance Engineer Intermec Technologies Corporation Safety & Compliance 6001 36 th Avenue West Everett, Washington 98203 United States tel 425 356 1765 fax 425 348 2633

NORTHWEST EMC, INC. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 November 16, 2004 Dear Application Examiner: On behalf of Intermec Technologies Corporation., Northwest EMC Inc is submitting this application for the certification of Intermec’s BTM311 transmitter, FCC ID: HN2- BTM311. It is a Bluetooth radio seeking modular approval under FCC 15.247. The radio utilizes a single integral antenna. This configuration satisfies the requirements of 47 CFR 15.203. The technical reports and exhibits demonstrate compliance with FCC rules 47 CFR 15.247 as a hybrid transmitter. Your efforts in reviewing this application are greatly appreciated. Best regards, Greg Kiemel, Director of Engineering Northwest EMC, Inc.

Northwest EMC TCB Approval Opinion Revision 05//02 INMC0149 Information about the Applicant Applicant: Intermec Technologies Corporation Address: 6001 36th Avenue West City, State, Zip Everett, WA 98203 Test Requested By: Katie Molina Model: HN2-BTM311 FCC ID: BTM311 Agent Northwest EMC, Inc. Approval Type Certification Equipment Type Low power intentional radiator – Modular Bluetooth Rule Part 15.247 Overview This application is for the certification of Intermec’s BTM311 transmitter, FCC ID: HN2-BTM311. It is a Bluetooth radio seeking modular approval under FCC 15.247. The radio utilizes a single integral antenna. This configuration satisfies the requirements of 47 CFR 15.203. The technical reports and exhibits demonstrate compliance with FCC rules 47 CFR 15.247 as a hybrid transmitter. Findings Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature Northwest EMC TCB Approval Opinion Revision 05//02 INMC0149 Opinion Specification Requirements Description 15.207 Conducted Power Line Emissions Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Technical Report Specification Requirements Description 15.247(a)(1)(ii) Bandwidth Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report Reference: Technical Report Specification Requirements Description 15.247(b)(1) Power Output Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report Reference: Technical Report Specification Requirements Description 15.247( c ) Spurious Emissions, Antenna Conducted Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report Reference: Technical Report Specification Requirements Description 15.247( c ) Spurious Emissions, Radiated Emissions Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Technical Report Northwest EMC TCB Approval Opinion Revision 05//02 INMC0149 Specification Requirements Description 15.247(d) Power Spectral Density Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report Reference: Technical Report Specification Requirements Description 15.247(c) Band Edge Compliance Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted test results in the form of a test report. Reference: Technical Report Specification Requirements Description 2.1091/15.247(b)(5) RF Exposure Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted MPE estimates demonstrating compliance. Reference: RF Exposure Exhibit Specification Requirements Description Additional Requirements FCC Compliance common to all Bluetooth Devices Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted the required information in the test report. Reference: Technical Report Specification Requirements Description Additional Requirements DA00-1407 – Modular Approval Requirements Opinion: The Equipment meets the intent specified by the requirements listed above. Discussion: The Applicant has submitted the required information in the test report. Reference: Applicant Letter supporting modular approval.

NORTHWEST EMC, INC. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 November 16,. 2004 Dear Application Examiner: Intermec’s Model BTM311, FCC ID: HN2-BTM311 is seeking modular approval. The radio meets the requirements for modular approval as detailed in FCC Public Notice DA00-1407. Compliance to each of the requirements is described below: 1. “The modular transmitter must have its own RF shielding.” The radio portion of the module is contained in its own RF shielding. The shielding is installed at the factory. Please see the Internal Photos exhibit. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs to insure compliance with Part 15 requirements under conditions of excessive data rates or over-modulation. Please see the Schematics exhibit. 3. “The modular transmitter must have its own power supply regulation.” The EUT has its own power supply regulation to insure compliance with Part 15 requirements regardless of the quality or level of external DC supplying the module from the host unit. Please see Schematics exhibit. Also, the technical report exhibit contains AC power line conducted emissions data taken with the EUT powered from a linear power supply that contains no EMC suppression components. 4. “The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c).” The EUT meets the FCC antenna requirements. Please see Antenna information exhibit and internal photos exhibit. 5. “The modular transmitter must be tested in a stand-alone configuration.” The EUT was tested in a stand-alone configuration. The module was greater than 10 cm from the host device. Please see test setup photos exhibit and technical report exhibit. 6. “The modular transmitter must be labeled with its own FCC ID number.” The EUT is labeled with its own FCC ID number. Please see FCC ID label & location exhibit. Since the FCC ID number will not be visible when the module is installed inside a host printer, another label with the FCC ID will be applied to the exterior of the printer. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the User Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. Please see RF Exposure Exhibit. Please contact me if you have additional questions. Your attention to this matter is greatly appreciated. Best regards, Greg Kiemel, Director of Engineering Northwest EMC, Inc.

November 3, 2004 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Re: HN2-BTM311 To Whom It May Concern: We hereby respectfully request that under the provision of 47 CFR 0.459, the documents listed below and attached with this application for certification under FCC ID: HN2-BTM311 be provided with confidential status. • Schematics • Theory of Operation • Frequency Block Diagram Any exhibit/information for which we have requested confidentiality, but which may not be accorded such treatment by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Sincerely, Katie Molina Compliance Engineer Safety & Compliance 6001 36 th Avenue West Everett, Washington 98203 United States tel 425 356 1765 fax 425 348 2633

FCC Labeling on Radio Module FCC Label on Example Host Device

418 APPLICATIONS ORDERING CODE FEATURES 7 6 5 432 1 AH104 F24 50 01–TQ AH Y Y Y YCompact , Lower profile. YWide bandwidth , High Gain. YStable temperature characteristics. . YBluetooth ® module, Wireless LAN. HIGH FREQUENCY MULTILAYER CHIP ANTENNA YBluetooth ® moduleLAN 1 OPERATING TEMP. K20VJ80C 3 0424.0P2.0 0838.0P3.0 10410.0P4.0 12212.0P2.0 [mm] 5 hMHzi 245024002500 525051505350 1. 2. 4 F N 2 F Q QW 7 01 6 KT AHAntenna for High Frequency 1 Type 3 0424.0P2.0 0838.0P3.0 10410.0P4.0 12212.0P2.0 Dimensions (case size)mm] 5 Frequency [MHz] example 245024002500 525051505350 1. Describe Center Frequency 2. Lower Frequency for Dualband 4 Special Code F N Electrode code 2 Inverted F Mono Pole (Dual) QWith Plating QWBlank space 7 Spec code 01 6 Packaging KTTape & reel 419 EXTERNAL DIMENSIONS HIGH FREQUENCY DIELECTRIC COMPONENT 6 P.419 Part Numbers Electrical Characteristics Packaging Reliability Data Precautions P.420P.422P.424 Selection Guide P.15 Part Numbers Electrical Characteristics Typical Characteristics etc P.426 Typical Characteristics on Taiyo Yuden evaluation board ItemCenter Frequency fMHzgPeak GainBandwidth 104F Series2450fTYPgJ2dBi300MHz fVSWR=2g 122F Series2450fTYPgJ1dBi200MHz fVSWR=3g 083F Series2450fTYPgJ2dBi145MHz fVSWR=3g 042F Series5250fTYPgJ1dBi240MHz fVSWR=2g 104N Series 2450fTYPg0dBi530MHz fVSWR=2g 5400fTYPgK1dBi 1.3GHz fVSWR=2g UnitDmm 104F 083F 122F 042F 104N 10M0.30 8M0.30 12M0.30 4M0.30 10M0.30 4M0.30 3M0.30 2M0.20 2M0.20 4M0.30 1M0.30 1M0.30 0.95M0.15 0.8M0.20 1M0.30 2.5M0.30 3.1M0.30 5.1M0.30 0M0.30 3M0.30 1M0.30 1M0.30 1M0.30 0.6M0.30 0.7M0.30 1M0.30 1.15M0.30 3.1M0.30 1.3M0.30 1.5M0.30 LWT a b cItem 420 Part Numbers Electrical Characteristics Typical Characteristics VSWR f104Fg Typical characteristics of VSWR f104F seriesg f104F @2.45GHzg Typical characteristics of radiation pattern f104F series @2.45GHzg VSWR f083Fg Typical characteristics of VSWR f083F seriesg f083F @2.45GHzg Typical characteristics of radiation pattern f083F series @2.45GHzg VSWR f122Fg Typical characteristics of VSWR f122F seriesg f122F @2.45GHzg Typical characteristics of radiation pattern f122F series @2.45GHzg 421 HIGH FREQUENCY DIELECTRIC COMPONENT 6 Part Numbers Electrical Characteristics Typical Characteristics VSWR f042F g Typical characteristics of VSWR f042F seriesg VSWR f104N 2GHzg Typical characteristics of VSWR f104N series 2GHz bandg VSWR f104N 5GHzg Typical characteristics of VSWR f104N series 5GHz bandg f104N @5.4GHzg Typical characteristics of radiation pattern f104N series @5.4GHzg f042F @5.25GHzg Typical characteristics of radiation pattern f042F series @5.25GHzg f104N @2.45GHzg Typical characteristics of radiation pattern f104N series @2.45GHzg 422 PACKAGING 3 Taping dimensions 8mm Embossed tapef0.315 inches wideg 2 Tape Material 1Minimum Quantity 5 Reel size 6Top Tape Strength 0.10.7N The top tape requires a peel-off force of 0.10.7N in the direction of the arrow as illustrated below. 4 Leader and Blank portion [pcs] TypeEmbossed Tape 104F,122F, 042F, 104N2000 083F1000 (EIA) Thickness Standard quantity [pcs] Type mm (inch) Embossed tape FTaped packaging 104F, 104N 122F 083F 042F 1.00typ.(0.040) 1.00typ.(0.040) 1.00typ.(0.040) 0.8typ.(0.031) 2000 2000 1000 2000 UnitDmmfinchg Type max fEIAg Chip cavityTape Widthness Insertion PitchTape Thickness ABCDFKT 104F, 104N 4.35M0.2510.35M0.224M0.311.5M0.18.0M0.11.450.3 f0.18M0.008gf0.41M0.008gf0.94M0.012gf0.45M0.004gf0.314M0.004gf0.057gf0.012g 122F 2.3M0.2512.3M0.224M0.311.5M0.14.0M0.11.350.35 f0.091M0.008gf0.48M0.008gf0.94M0.012gf0.45M0.004gf0.157M0.004gf0.053gf0.012g 083F 3.35M0.258.35M0.216M0.37.5M0.18.0M0.11.450.3 f0.13M0.008gf0.33M0.008gf0.63M0.012gf0.3M0.004gf0.314M0.004gf0.057gf0.012g 042F 2.3M0.254.3M0.212M0.25.5M0.14.0M0.11.150.25 f0.091M0.008gf0.17M0.008gf0.47M0.008gf0.22M0.004gf0.157M0.004gf0.045gf0.01g ReelABWT 104F, 104N 330M2.0100M1.025.5M13.0MAX f13.0M0.08gf3.94M0.04gf1M0.04gf0.12g 122F 330M2.0100M1.025.5M13.0MAX f13.0M0.08gf3.94M0.04gf1M0.04gf0.12g 083F 178M2.050MIN17.0M12.5MAX f7.09M0.08gf2.0gf0.67M0.04gf0.1g 042F 178M2.050MIN14.0M12.5MAX f7M0.08gf2.0gf0.55M0.04gf0.1g UnitDmmfinchg 425 HIGH FREQUENCY DIELECTRIC COMPONENT 6 RELIABILITY DATA Test Methods and RemarksItemSpecified Value 1. Operating Temperature Range 2. Storage Temperature Range 3. Solderability 4. Thermal shock 5. High Temperature Storage Test 6. Low Temperature Storage Test 7. Humidity Storage Test 8. Resistance to Reflow K20VJ80C K40VJ85C At least 90% of Terminal surface immersed is covered by new solder. shall satisfy required VSWR value of individual specifications for each item. shall satisfy required VSWR value of individual specifications for each item. shall satisfy required VSWR value of individual specifications for each item. shall satisfy required VSWR value of individual specifications for each item. shall satisfy required VSWR value of individual specifications for each item. with being taped, K20VJ35C Solder temperature230M5C Duration3M1 sec. PreconditioningPreheating at 150C after immersion into flux. 1 hour of recovery after 10 times of 30min.immersion alternately at K40C and 85C of temperature,followed by evaluating electrical characteristics. 1 hour of recovery under standard condition after 96 hours recovery with85C of temperature,followed by evaluating electrical characteristics. 1 hour of recovery under standard condition after 96 hours recovery with K40C of temperature, followed by evaluating electrical characteristics. 1 hour of recovery under standard condition after 96 hours recovery with 60C of temperature, 9095% relative humidity followed by evaluating electrical characteristics. Two times of Reflow soldering by recommended profile attached, followed by evaluating electrical characteristics. 427 HIGH FREQUENCY DIELECTRIC COMPONENT 6 PRECAUTIONS StagesPrecautionsTechnical considerations 1. PCB Design Land pattern design Please don't arrange the surface and inside layer pattern near the antenna mounting area. Land pattern dimens…

Text truncated - open the document above for the full version.

Compliance with 47 CFR 15.247(i) “Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this chapter.” The EUT is a Bluetooth radio seeking modular approval as a portable device. The antenna is internal to the unit and permanently attached. The antenna is an Inverted F antenna with 2.0 dBi gain. The maximum peak conducted output power is 8.69 mW. The maximum peak power is 13.77 mW (EIRP) for FCC ID: HN2-BTM311. The transmit frequency is 2402 to 2480 MHz, therefore the EUT does not require routine SAR evaluation per “TCB Exclusions List”, footnote 3 (dated July 17, 2002). See below: The exposure category is “General Population”. The distance is < 2.5 cm. Therefore the “Low Threshold” is 24.5 mW (EIRP) – above which routine SAR evaluation would be required. Since the maximum peak power of the EUT is 13.77 mW (peak EIRP), routine SAR evaluation is not required. The applicant’s Bluetooth radio, FCC ID: HN2-BTM311, is compliant with the requirements of 15.247(i).

INTERMEC Technologies Corporation BTM311 November 12, 2004 Report No. INMC0167 Rev 01 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2004 Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Issue Date: November 12, 2004 INTERMEC Technologies Corporation Model: BTM311 Emissions Specification Test Method Pass Fail FCC 15.207 AC Powerline Conducted Emissions:2003 ANSI C63.4:2001 FCC 15.247(a) Occupied Bandwidth:2003 ANSI C63.4:2001 FCC 15.247(b) Output Power:2003 ANSI C63.4:2001 FCC 15.247(d) Band Edge Compliance:2003 ANSI C63.4:2001 FCC 15.247(c) Spurious Conducted Emissions:2003 ANSI C63.4:2001 FCC 15.247(d) Spurious Radiated Emissions:2003 ANSI C63.4:2001 FCC 15.247(e) Power Spectral Density:2003 ANSI C63.4:2001 Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400; Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada. Approved By: Don Facteau, IS Manager This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested, the specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 05/05/03 Revision Number Description Date Page Number 01 Spec limit info corrected 11/21/04 2 01 ANSI C63.4 date corrected 11/21/04 49,66 01 Added Bluetooth Approvals information 11/21/04 75 Northwest EMC Accreditations and Authorizations Revision 04/01/04 FCC: Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities, have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP: Northwest EMC, Inc. is recognized under the United States Department of Commerce, National Institute of Standards and Technology, National Voluntary Laboratory Accreditation Program for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 89/336/EEC, ANSI C63.4, MIL-STD 461E, DO-160D and SAE J1113. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. Accreditation has been granted to Northwest EMC, Inc. under Certificate Numbers: 200629-0, 200630-0, and 200676-0. Industry Canada: Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS 212, Issue 1 (Provisional) and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by NIST and recognized by Industry Canada as a Certification Body (CB) per the APEC Mutual Recognition Arrangement (MRA). This allows Northwest EMC to certify transmitters to Industry Canada technical requirements. CAB: Designated by NIST and validated by the European Commission as a Conformity Assessment Body (CAB) to conduct tests and approve products to the EMC directive and transmitters to the R&TTE directive, as described in the U.S. - EU Mutual Recognition Agreement TÜV Product Service: Included in TUV Product Service Group's Listing of Recognized Laboratories. It qualifies in connection with the TUV Certification after Recognition of Agent's Testing Program for the product categories and/or standards shown in TUV's current Listing of CARAT Laboratories available from TUV. A certificate was issued to represent that this laboratory continues to meet TUV's CARAT Program requirements. Certificate No. USA0401C Northwest EMC Accreditations and Authorizations Revision 04/01/04 TÜV Rheinland: Authorized to carryout EMC tests by order and under supervision of TÜV Rheinland. This authorization is based on "Conditions for EMC- Subcontractors" of November 1992. NEMKO: Assessed and accredited by NEMKO (Norwegian testing and certification body) for European emissions and immunity testing. As a result of NEMKO's laboratory assessment, they will accept test results from Northwest EMC, Inc. for product certification (Authorization No. ELA 119). Technology International: Assessed in accordance with ISO Guide 25 defining the general international requirements for the competence of calibration and testing laboratories and with ITI assessment criteria LACO196. Based upon that assessment Interference Technology International, Ltd., has granted approval for specifications implementing the EU Directive on EMC (89/336/EEC and amendments). The scope of the approval was provided on a Schedule of Assessment supplied with the certificate and is available upon request. Australia/New Zealand: The National Association of Testing Authorities (NATA), Australia has been appointed by the ACA as an accreditation body to accredit test la…

Text truncated - open the document above for the full version.