IMA-TDFM-7300-2Multiple P25 Airborne Transceiver

TDFM-7300-2 MULTIBAND P25 AIRBORNE TRANSCEIVER Installation and Operating Instructions TiL Document No. 10RE430 Rev. A NOVEMBER 2010 Technisonic Industries Limited 240 Traders Boulevard, Mississauga, Ontario L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 www.til.ca Copyright 2009 by Technisonic Industries Limited. All rights reserved. REVISION HISTORY [ 10RE430 ] REV SECTION - PAGE - DESCRIPTION DATE Edited by A iii Changed 70cm to 80cm. 26 Nov 2010 SM TDFM-7300-2 Installation & Operating Instructions TiL 10RE430A iii NOTES CAUTION ! STATIC SENSITIVE ! This unit contains static sensitive devices. Wear a grounded wrist strap and/or conductive gloves when handling printed circuit boards. FCC COMPLIANCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: For compliance with FCC RF Exposure Requirements the mobile transmitter antenna installation shall comply with the following two conditions: 1. The transmitter antenna gain shall not exceed 3 dBi. 2. The transmitter antennas shall be located outside of a vehicle and must not be co-located (kept at a separation distance of more than 20cm from each other when installed). Also they must be installed in such a way that they always maintain a separation distance of more than 80cm from any person during operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense. WARNING Changes or modifications not expressly approved by Technisonic Industries could void the user’s authority to operate the equipment. WARRANTY INFORMATION The Model TDFM-7300-2 Transceiver is under warranty for one year from date of purchase. Failed units caused by defective parts, or workmanship should be returned to: Technisonic Industries Limited 240 Traders Boulevard Mississauga, Ontario L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 TDFM-7300-2 Installation & Operating Instructions TiL 10RE430A iv Summary of DO-160C Environmental Testing for Technisonic Model TDFM-7300-2 Transceiver. CONDITIONS SECTION DESCRIPTION OF CONDUCTED TESTS Temperature and Altitude 4.0 Equipment tested to categories C4 and D1. Vibration 8.0 Equipment is tested without shock mounts to categories B, M and N. Magnetic Effect 15.0 Equipment is class Z. Power Input 16.0 Equipment tested to category B. Voltage Spike 17.0 Equipment tested to category B. RF Emission 21.0 Equipment tested to category Z. STC APPROVAL NOTE Presently, no TSO standard exists for airborne FM transceivers. To make it easier for installation agencies to provide their customers with an approved installation supported by an effective Airworthiness Approval, Technisonic has secured Supplemental Type Certificate (STC) Approvals (both US and Canadian) on its Airborne FM products for many helicopters currently being delivered in the US and Canada as well as a number of single engine fixed wing aircraft. The above referenced DO-160C test data is also on file and available from Technisonic to support approval requirements in airframes for which Technisonic does not possess an STC. Approved aircraft types are listed in the attachments to the formal STC documents. These STCs are the exclusive property of Technisonic and require the written authority of Technisonic for their use. To assist Factory Authorized Technisonic Dealers in the certification process, we have placed copies of our Canadian and US STCs on our web site along with a letter of authorization for their use. These documents may be downloaded and used as support for the technical submission to FAA or Transport Canada. Only authorized factory dealers/installers are permitted to download and make use of these documents on behalf of their customers (end users) in support of regulatory agency approval. Please refer to the Technisonic web site www.til.ca for the latest issue of available STCs and letter of authorization for use. COPYRIGHT NOTICE This document contains designs and other information which are the property of Technisonic Industries Ltd. Except for rights expressly granted by contract to the Canadian Government, or to the United States Government, this document may not, in whole or in part, be duplicated or disclosed or used for manufacture of the part disclosed herein, without the prior permission of Technisonic Industries Ltd. WARNING AND DISCLAIMER This manual is designed to provide information about the TDFM-7300-2. Every effort has been made to make this manual as complete and accurate as possible. TRADEMARK NOTICES TDFM-7300-2 Transceivers contain two-way radio protocols licensed from Motorola, Inc. © 1997, 1998 Motorola, Inc. TECHNISONIC INDUSTRIES LIMITED www.til.ca TDFM-7300-2 Installation & Operating Instructions TiL 10RE430A v TABLE OF CONTENTS SECTION 1 GENERAL DESCRIPTION 1.1 INTRODUCTION ...................................................................................................................... 1-1 1.2 DESCRIPTION ......................................................................................................................... 1-1 1.3 MODEL VARIATION ................................................................................................................ 1-1 1.4 TECHNICAL CHARACTERIS…

Text truncated - open the document above for the full version.

Technisonic Industries Limited 240 Traders Blvd., Mississauga, Ontario L4Z 1W7 Tel.: (905) 890-2113 Fax: (905) 890-5338 December 10, 2010 FEDERAL COMMUNICATIONS COMMISSION 7435 Oakland Mills Road Columbia, MD 21046 USA FCC ID: IMA-TDFM-7300-2 Dear Sir/Madam, Technisonic understands the following Part 90 UHF spectrum and would like the FCC to certify the entire 403-512MHz spectrum to include the part 90 extended frequencies. This would be done to facilitate the requirements of agencies covered under NTIA spectrum usage. Government agencies complying with the NTIA instead of the FCC must purchase their equipment from private industry manufacturers who are governed by FCC rules. The conflict in spectrum allocation detracts from the options available to government agencies for commercial off the shelf equipment which meets their required specifications such as the requirements stated in the Department of the Interior’s Narrowband digital radio contract. Part 90 extended frequencies: 406.1 – 410.0 MHz 410.0 – 420.0 MHz 450.0 – 454.0 MHz 456.0 – 460.0 MHz 460.0 – 462.5375 MHz 462.7375 – 467.5375 MHz 467.7375 – 470.0 MHz 470.0 – 512 MHz Regards Steve McIntosh Engineering Manager

TECHNISONIC INDUSTRIES LIMITED 240 TRADERS BLVD., MISSISSAUGA, ONTARIO L4Z 1W7 TEL.: (905) 890-2113 FAX: (905) 890-5338 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 November 22, 2010 SUBJECT: FCC Application for FCC ID: IMA-TDFM-7300-2 To Whom It May Concern: This equipment meets the requirements of the FCC Rules, Part 90.203(e). The operator cannot program and transmit on frequencies other than those programmed by the manufacturer, service or maintenance personnel. Regards, Steve McIntosh Engineering Manager Technisonic Industries Limited (905) 890-2113 ext-205 [email protected]

TECHNISONIC INDUSTRIES LIMITED 240 TRADERS BLVD., MISSISSAUGA, ONTARIO L4Z 1W7 TEL.: (905) 890-2113 FAX: (905) 890-5338 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 November 22, 2010 SUBJECT: FCC Application for FCC ID: IMA-TDFM-7300-2 To Whom It May Concern: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15B, Unintentional Radiators of the FCC Rules. Regards, Steve McIntosh Engineering Manager Technisonic Industries Limited (905) 890-2113 ext-205 [email protected]

September 9, 2010 Ultratech Engineering Labs, Inc. 3000 Bristol Circle Oakville, Ontario L6H 6G4 Subject: Equipment Authorization under FCC 47 CFR, Parts 2 and 90 (Subpart I) - Non-Broadcast Radio Transceivers Operating in the Frequency Band 406.1-470 MHz (25 KHz and 12.5 KHz Channel Spacings). Applicant: ICOM Incorporated Product: UHF Mobile Transceiver Model: IC-F6011 FCC ID: AFJ333501 Dear Sir/Madam, As appointed agent for ICOM Incorporated, we would like to submit the application to Federal Communications Commission for certification of the above product. Please review all files uploaded to your electronic filing site. If you have any queries, please do not hesitate to contact us by our TOLL FREE number: OUR TELEPHONE NO.: 1-877-747-6381 Yours truly, xutianlu Steven (Xu Tian) Lu Authorized Agent UltraTech Group of Labs FCC TCB & IC CB Ultratech’s Accreditations: 0685 FCC 91038 1309 46390-2049 NVLAP Lab Code 200093-0 SL2-IN-E-1119R Korea KCC-RRL CA2049 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com

Technisonic Industries Limited 240 Traders Blvd., Mississauga, Ontario L4Z 1W7 Tel.: (905) 890-2113 Fax: (905) 890-5338 November 22, 2010 To Whom It May Concern Subject: Authority to Act as an Agent Applicant: Technisonic Industries Ltd. FCC ID: IMA-TDFM-7300-2 Dear Sir/Madam, I hereby appoint UltraTech Engineering Labs Inc. (UltraTech) to act as my agent in preparation of this application for authorization of above equipment under F.C.C. Rules. The applicant hereby certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a “party” for these purposes. I also certify that the information provided, properly describe the device or system for which authorization is required. Regards Steve McIntosh Engineering Manager

Technisonic Industries Limited 240 Traders Blvd., Mississauga, Ontario L4Z 1W7 Tel.: (905) 890-2113 Fax: (905) 890-5338 November 22, 2010 To Whom It May Concern Subject: Confidentiality Letter Applicant: Technisonic Industries Ltd. FCC ID: IMA-TDFM-7300-2 Dear Sir/Madam, The applicant would like to request the following documents submitted with this application for certification be withheld from public disclosure as per Section 0.457 & 0.459 of FCC Rules. 1. Operational Description 2. Block Diagram 3. Schematics 4. Parts List 5. Tuning Info The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the grant for this application. Regards Steve McIntosh Engineering Manager

ANNEX 2 – External Photos Photo # 1 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 2 – External Photos Photo # 2 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 2 – External Photos Photo # 3 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 2 – External Photos Photo # 4 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2

ANNEX 3 – Internal Photos Photo # 1 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 2 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 3 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 4 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 5 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 6 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 7 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 8 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 9 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 10 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 11 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 12 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 13 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 14 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 15 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 16 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 17 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 18 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 19 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 20 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 21 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 22 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 23 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 24 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 25 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 26 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 27 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 28 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 29 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 30 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 ANNEX 3 – Internal Photos Photo # 31 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2

TDFM-7300-2 Installation & Operating Instructions TiL 10RE430A iii INFORMATION NOTES CAUTION ! STATIC SENSITIVE ! This unit contains static sensitive devices. Wear a grounded wrist strap and/or conductive gloves when handling printed circuit boards. FCC COMPLIANCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: For compliance with FCC RF Exposure Requirements the mobile transmitter antenna installation shall comply with the following two conditions: 1. The transmitter antenna gain shall not exceed 3 dBi. 2. The transmitter antenna is required to be located outside of a vehicle and kept at a separation distance of 80 cm or more between the transmitter antenna of this device and person(s) during operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense. WARNING Changes or modifications not expressly approved by Technisonic Industries could void the user’s authority to operate the equipment. WARRANTY INFORMATION The Model TDFM-7300-2 Transceiver is under warranty for one year from date of purchase. Failed units caused by defective parts, or workmanship should be returned to: Technisonic Industries Limited 240 Traders Boulevard Mississauga, Ontario L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 NOTICE: The above stated address supersedes all others that may appear otherwise in this manual. FCC Parts 2 & 90, Subpart I, Non-Broadcast Radio Transceivers Page 71 Multiple P25 Airborne Transceiver, Model TDFM-7300-2 FCC ID: IMA-TDFM-7300-2 ULTRATECH GROUP OF LABS File #: TIL-069F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 December 17, 2010 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) 5.8. RF EXPOSURE REQUIRMENTS [§§ 1.1310 & 2.1091] The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation. FCC 47 CFR § 1.1310: 5.8.1. Method of Measurements Refer to Sections 1.1310, 2.1091 In order to demonstrate compliance with MPE requirements (see Section 2.1091), the following information is typically needed: (1) Calculation that estimates the minimum separation distance (20 cm or more) between an antenna and persons required to satisfy power density limits defined for free space. (2) Antenna installation and device operating instructions for installers (professional/unskilled users), and the parties responsible for ensuring compliance with the RF exposure requirement (3) Any caution statements and/or warning labels that are necessary in order to comply with the exposure limits (4) Any other RF exposure related issues that may affect MPE compliance FCC Parts 2 & 90, Subpart I, Non-Broadcast Radio Transceivers Page 72 Multiple P25 Airborne Transceiver, Model TDFM-7300-2 FCC ID: IMA-TDFM-7300-2 ULTRATECH GROUP OF LABS File #: TIL-069F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 December 17, 2010 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) Calculation Method of RF Safety Distance: 22 44r EIRP r GP S       Where: P: power input to the antenna in mW EIRP: Equivalent (effective) isotropic radiated power S: power density mW/cm 2 G: numeric gain of antenna relative to isotropic radiator r: distance to centre of radiation in cm 5.8.2. RF Evaluation Evaluation of RF Exposure Compliance Requirements RF Exposure Requirements Compliance with FCC Rules Minimum calculated separation distance between antenna and persons required: 77 cm Manufacturer’ instruction for separation distance between antenna and persons required: 80 cm. Antenna installation and device operating instructions for installers (professional/unskilled users), and the parties responsible for ensuring compliance with the RF exposure requirement Antenna installation and device operating instructions shall be provided to installers to maintain and ensure compliance with RF exposure requirements. Caution statements and/or warning labels that are necessary in order to comply with the exposure limits Refer to User’s Manual for RF Exposure Information. Any other RF exposure related issues that may affect MPE compliance None. *The minimum separation distance between the antenna and bodies of users are calculated using the following formula: RF EXPOSURE DISTANCE LIMITS S EIRP S GP r      44 S = f/1500 = 403 / 1500 = 0.27 mW/cm 2 EIRP = 40.04 dBm + 3 dBi = 43.04 dBm = 20137.2 mW (worst case) (Minimum Safe Distance, r) = cm S EIRP 77 )27.0(4 20137.2 4     

Multiple P25 Airborne Transceiver Model No.: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2 Applicant: Technisonic Industries Limited 240 Traders Blvd. E. Mississauga, Ontario Canada L4Z 1W7 Tested in Accordance With Federal Communications Commission (FCC) 47 CFR, Parts 2 and 90 (Subpart I) UltraTech's File No.: TIL-069F90 This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: December 17, 2010 Report Prepared by: Dan Huynh Issued Date: December 17, 2010 Tested by: Wayne Wu, RFI Engineer Test Dates: November 22 - Dec. 15, 2010  The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected.  This report must not be used by the client to claim product endorsement by NVLAP or any agency of the US Government. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Tel.: (905) 829-1570 Fax.: (905) 829-8050 Website: www.ultratech-labs.com , Email: [email protected], Email: [email protected] FCC Korea KCC-RRL 91038 1309 46390-2049 NvLap Lab Code 200093-0 SL2-IN-E-1119R CA2049 FCC Parts 2 & 90, Subpart I, Non-Broadcast Radio Transceivers Contents i Multiple P25 Airborne Transceiver, Model TDFM-7300-2 FCC ID: IMA-TDFM-7300-2 ULTRATECH GROUP OF LABS File #: TIL-069F90 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 December 17, 2010 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. INTRODUCTION ......................................................................................................................................... 1 1.1. SCOPE ......................................................................................................................................................................... 1 1.2. RELATED SUBMITTAL(S)/GRANT(S) ................................................................................................................... 1 1.3. NORMATIVE REFERENCES ................................................................................................................................... 1 EXHIBIT 2. PERFORMANCE ASSESSMENT .............................................................................................................. 2 2.1. CLIENT INFORMATION .......................................................................................................................................... 2 2.2. EQUIPMENT UNDER TEST (EUT) INFORMATION .............................................................................................. 2 2.3. EUT’S TECHNICAL SPECIFICATIONS .................................................................................................................. 3 2.4. LIST OF EUT’S PORTS ............................................................................................................................................. 3 EXHIBIT 3. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS ............................... 4 3.1. CLIMATE TEST CONDITIONS ................................................................................................................................ 4 3.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST SIGNALS .............................................. 4 EXHIBIT 4. SUMMARY OF TEST RESULTS ............................................................................................................... 5 4.1. LOCATION OF TESTS .............................................................................................................................................. 5 4.2. APPLICABILITY & SUMMARY OF EMISSION TEST RESULTS ......................................................................... 5 4.3. DEVIATION OF STANDARD TEST PROCEDURES .............................................................................................. 5 4.4. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ......................................... 6 EXHIBIT 5. MEASUREMENTS DATA ........................................................................................................................... 7 5.1. RF POWER OUTPUT [§§ 2.1046 & 90.205] .............................................................................................................. 7 5.2. FREQUENCY STABILITY [§§ 2.1055 & 90.213] ..................................................................................................... 9 5.3. AUDIO FREQUENCY RESPONSE [§ 2.1047(A)] ................................................................................................... 11 5.4. MODULATION LIMITING [§§ 2.1047(B) & 90.210] .............................................................................................. 17 5.5. OCCUPIED BANDWIDTH & EMISSION MASK [§§ 2.1049, 90.209 & 90.210] ................................................... 22 5.6. TRANSMITTER ANTENNA POWER SPURIOUS/HARMONIC CONDUCTED EMISSIONS [§§ 2.1051 & 90.210] ................................................................................................................................................................................... 48 5.7. TRANSMITTER SPURIOUS/HARMONIC RADIATED EMISSIONS [§§ 2.1053 & 90.210] ............................... 66 5.8. RF EXPOSURE REQUIRMENTS [§§ 1.1310 & 2.1091] ......................................................................................... 72 5.9. TRANSIENT FREQUENCY BEHAVIOR [§ 90.214] .............................................................................................. 74 EXHIBIT 6. TEST INSTRUMENTS & MEASUREMENT UNCERTAINTY (K=2, 95% CONFIDENCE LEVEL) 80 RADIATED EMISSION MEASUREMENT UNCERTAINTY ............................................................................................................ 80 EXHIBIT 7. MEASUREMENT METHODS ............…

Text truncated - open the document above for the full version.

ANNEX 1 - TEST SETUP PHOTOGRAPHS Photo # 1 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 Plot #1: Radiated Emission Test Setup ANNEX 1 - TEST SETUP PHOTOGRAPHS Photo # 2 Technisonic Industries Limited Multiple P25 Airborne Transceiver, Model: TDFM-7300-2 FCC ID: IMA-TDFM-7300-2, IC: 120A-TDFM7300-2 Plot #2: Radiated Emission Test Setup