IMR1106CB2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card

Agere Systems 1106 CardBus Draft Manual 1106 CardBus Preliminary User Manual Agere Systems 1106 CardBus Draft Manual Agere Systems 1106 CardBus Draft Manual Agere Systems 1106 CardBus Draft Manual Agere Systems 1106 CardBus Draft Manual Agere Systems 1106 CardBus Draft Manual Agere Systems 1106 CardBus Draft Manual Section: Regulatory Compliance Information Information to the user It is the policy of Agere Systems Inc. to provide customers with the latest available information. All updates to this document will appear in the English version first. This document provides regulatory information about Agere wireless LAN products. This product can operate on channels in frequency bands in 2.4 GHz and 5 GHz ranges, and uses DSSS (Direct Sequence Spread Spectrum) or OFDM radio technology. It is designed to be inter-operable with similar wireless products that comply with: - IEEE 802.11 b/g/a Standards on Wireless LAN, as defined and approved by the Institute of Electrical and Electronics Engineers - Wireless Fidelity (Wi-Fi) certification as defined by the Wi-Fi Alliance formerly known as WECA (Wireless Ethernet Compatibility Alliance) For the country and date of manufacturing, consult the identification label of your wireless device. 1. Wireless LAN and your Health Wireless LAN products are radio devices that emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices is much less than the electromagnetic energy emitted by devices like for example mobile telephones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, Agere believes this product is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. See additional information for North America in section 2.1. Agere Systems 1106 CardBus Draft Manual Important Safety Instructions When using this product, always follow the basic precautions to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Always install the product as described in the documentation that is included with your product. 2. Do not use this product near water, for example, near a bathtub, washbowl, and kitchen sink or laundry tub, in a wet basement or near a swimming pool. 3. Avoid using this product during an electric storm. There may be a remote risk of electric shock from lightning 4. Do not use this product to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS Agere Systems 1106 CardBus Draft Manual 2. Regulatory Information You must install and use this device in strict accordance with the manufacturerís instructions as described in the user documentation that is included with your product. Before you start installation or use of this product, carefully read the contents of this document for device specific constraints or rules that may apply in the country where you want to use this product. The user must always ensure that country and/or channel selection of Peer-to-Peer groups or Base Station Networks matches the regulations of the country of operation. In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: - Using the wireless equipment on board of airplanes, or - In any environment where the risk of interference to other devices or services is perceived or identified as harmful. If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use this device prior to turning on the equipment. The manufacturer is mot responsible for any radio or television interference caused by unauthorized modification of the device, or the substitution or attachment of connecting cables and equipment other than specified by manufacturer. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The manufacturer and it authorized resellers or distributors are not liable for any damage or violation that may arise from failing to comply with these guidelines. 2.1 North America Canada ñ Industry Canada (IC) The wireless radio of this device complies with RSS 210 of Industry Canada. This Class B device complies with Canadian ICES-003 (NMB-003). Agere Systems 1106 CardBus Draft Manual USA – Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules. Operation of the device is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation. Operation in frequency band 5150-5250 MHz is restricted to indoor environments only. Exposure to Radio Frequency Radiation SAR (Specific Absorption Rate) compliance has been established and found to comply in accordance with FCC OET Bulletin 65 and guidelines of IEEE C95.1-1995. Caution: ! To comply with the FCC RF Exposure compliance requirements, the user is advised to maintain a distance of at least 5 mm (0.2 inch) from the antenna of the device while in use This device may only be installed in those hosts which will provide a minimum separation distance of 5 mm (0.2 inch) between the antenna and the user under all operating conditions. Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Agere Systems 1106 CardBus Draft Manual This equipment generates, uses, an…

Text truncated - open the document above for the full version.

TNO Electronic Products & Services (EPS) B.V. Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek / Netherlands Organisation for Applied Scientific Research Smidshornerweg 18 P.O. Box 15 9822 ZG Niekerk The Netherlands www.tno.nl T +31 594 505005 F +31 594 504804 E [email protected] Subject Cover letter Date August 2, 2004 Our reference 04K0593a Your reference - Page 1 of 3 Our General Terms and Conditions, as filed at the Chamber of Commerce in Groningen, are applicable to all orders given to TNO Electronic Products & Services (EPS) B.V. TNO Electronic Products & Services (EPS) B.V. is registered at the Chamber of Commerce in Groningen with no. 27247331. Return address: P.O. Box 15, 9822 ZG Niekerk, The Netherlands Office of Engineering and Technology Laboratory Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046-1609 U.S.A. Dear Mr./Ms., On behalf of our customer Agere Systems Nederland B.V., we hereby would like to apply for FCC certification (limited modular approval, see also excerpt of DA 00-1407 and remarks on the second page and onwards) of the following device: FCC ID : IMR1106CB Brand : Agere Model number : 1106 Description : 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card The following PDF files (exhibits) are electronically submitted: 1. Cover letter containing the request for FCC certification 2. Request for confidentiality 3. Test report(s) in conformity with 47 CFR Part 15 (a) Test report 47 CFR Part 15.247 (2412 ñ 2462 MHz) (b) Test report 47 CFR Part 15.247 (2467 ñ 2472 MHz) (c) Test report 47 CFR Part 15.247 (5725 ñ 5850 MHz) (d) Test report 47 CFR Part 15.407 (5150 ñ 5350 MHz) 4. Bill of materials 5. Circuit diagram 6. Block diagram 7. Operational description 8. Interior photographs 9. Exterior photographs 10. Test setup photographs 11. SAR test report (including calibration data) 12. Authorization letter 13. User manual 14. Label information Best regards, TNO Electronic Products & Services (EPS) B.V. P.A.J.M. Robben, B.Sc.E.E. Marketing Manager Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek / Netherlands Organisation for Applied Scientific Research Date August 2, 2004 Our reference 04K0593a Your reference - Page 2 of 3 Excerpt of DA 00-1407 In order to obtain a modular transmitter approval, a cover letter requesting modular approval must be submitted and the numbered requirements identified below must be addressed in the application for equipment authorization. 1. The modular transmitter must have its own RF shielding. This is intended to ensure that the module does not have to rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with Part 15 limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Such coupling may result in non-compliant operation. Remark: The modular transmitter has its own RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Remark: The transmitter has buffered modulation/data inputs. 3. The modular transmitter must have its own power supply regulation. This is intended to ensure that the module will comply with Part 15 requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. Remark: The transmitter has its own integrated and dedicated power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a ìuniqueî antenna coupler (at all connections between the module and the antenna, including the cable). Any antenna used with the module must be approved with the module, either at the time of initial authorization or through a Class II permissive change. The ìprofessional installationî provision of Section 15.203 may not be applied to modules. Remark: The modular transmitter has an integral antenna. The antenna connector intended for use in combination with an external antenna complies with the ìunique antenna couplerî definition of the FCC. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek / Netherlands Organisation for Applied Scientific Research Date August 2, 2004 Our reference 04K0593a Your reference - Page 3 of 3 Remark: The modular transmitter has not been tested in a stand-alone configuration in order to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module i…

Text truncated - open the document above for the full version.

July 30, 2004 To whom it may concern, This letter confirms the agreement that; TNO Electronic Products & Services (EPS) B.V. Smidshornerweg 18 9822 TL Niekerk The Netherlands is authorized as an agent for; Agere Systems Netherlands B. V. Zadelstede 1 -10 3431 JZ Nieuwegein Netherlands and is authorized to sign application forms and act on behalf of Maarten Visee (Agere Systems Netherlands B.V.) and is authorized to receive and exchange data between Maarten Visee (Agere Systems Netherlands B.V.) and European/non-European national authorities regarding the -certification of- and/or -arranging type approvals for- product(s) of Agere Systems Netherlands B.V. This authorization will expire on July 30, 2005 or upon earlier written notice from Agere Systems Netherlands B.V. Maarten Visee Hardware Development Manager Tel.: +31-30-609-7458 Fax: +31-30-609-7556 Email: [email protected] Yours sincerelyY'l

TNO Electronic Products & Services (EPS) B.V. Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek / Netherlands Organisation for Applied Scientific Research Smidshornerweg 18 P.O. Box 15 9822 ZG Niekerk The Netherlands www.tno.nl T +31 594 505005 F +31 594 504804 E [email protected] Subject Request for confidentiality Date August 2, 2004 Our reference 04K0593b Your reference - Page 1 of 1 Our General Terms and Conditions, as filed at the Chamber of Commerce in Groningen, are applicable to all orders given to TNO Electronic Products & Services (EPS) B.V. TNO Electronic Products & Services (EPS) B.V. is registered at the Chamber of Commerce in Groningen with no. 27247331. Return address: P.O. Box 15, 9822 ZG Niekerk, The Netherlands Office of Engineering and Technology Laboratory Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046-1609 U.S.A. Dear Mr./Ms., Pursuant to section 0.457 of the FCC rules we herewith request the following exhibits, related to this application for FCC ID: IMR1106CB, to be withheld from public inspection and to be kept confidential. The contents of these exhibits may not be disclosed to other parties than Agere Systems Nederland B.V. and TNO Electronic Products & Services (EPS) B.V.: 1. Bill of materials 2. Circuit diagram 3. Operational description 4. Block diagram The reason for this request for confidentiality is that the information contained in the exhibits as listed above has been classified as company confidential. Disclosure of any portion of this information to other parties would cause substantial competitive harm. Best regards, TNO Electronic Products & Services (EPS) B.V. P.A.J.M. Robben, B.Sc.E.E. Marketing Manager

Testing and certification of electric, electronic and radio equipment/installations including telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Web: www.eps.tno.nl Project number: 04061405.p02 Page 1 of 5 EXTERIOR PHOTOGRAPHS OF A 2.4/5 GHZ IEEE 802.11g/a WLAN CARDBUS CARD, BRAND AGERE, MODEL 1106 (32-BITS CARDBUS INTERFACE). FCC listed Industry Canada VCCI registered : : : 90828 IC3501 R-1518, C-1598 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p02 Page 2 of 5 Description of test item Test item : 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Manufacturer : Agere Systems Nederland B.V. Brand : Agere Model : 1106 (32-bits Cardbus interface) Serial numbers : 04NG22910024 and 04NG28910012 Revision : D1 & D2 Receipt number : 1 Receipt date : June 14, 2004 and July 21, 2004 Applicant information Applicant's representative : Mr. F. Hoekstra Company : Agere Systems Nederland B.V. Address : Zadelstede 1-10 Postal code : 3431 JZ City : Nieuwegein PO-box : 755 Postal code : 3430 AT City : Nieuwegein Country : The Netherlands Telephone number : +31 30 609 7406 Telefax number : +31 30 609 7556 This report is in conformity with NEN-EN-ISO/IEC 17025. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p02 Page 3 of 5 Table of contents 1 Exterior photographs ..............................................................................................................................................................4 1.1 Top view.........................................................................................................................................................................4 1.2 Bottom view ...................................................................................................................................................................5 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p02 Page 4 of 5 1 Exterior photographs 1.1 Top view Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p02 Page 5 of 5 1.2 Bottom view

Testing and certification of electric, electronic and radio equipment/installations including telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Web: www.eps.tno.nl Project number: 04061405.p03 Page 1 of 5 EXTERIOR PHOTOGRAPHS OF A 2.4/5 GHZ IEEE 802.11g/a WLAN CARDBUS CARD, BRAND AGERE, MODEL 1106 (16-BITS CARDBUS INTERFACE). FCC listed Industry Canada VCCI registered : : : 90828 IC3501 R-1518, C-1598 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p03 Page 2 of 5 Description of test item Test item : 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Manufacturer : Agere Systems Nederland B.V. Brand : Agere Model : 1106 (16-bits Cardbus interface) Serial numbers : 04NG3100004 Revision : D2 Receipt number : 1 Receipt date : July 28, 2004 Applicant information Applicant's representative : Mr. F. Hoekstra Company : Agere Systems Nederland B.V. Address : Zadelstede 1-10 Postal code : 3431 JZ City : Nieuwegein PO-box : 755 Postal code : 3430 AT City : Nieuwegein Country : The Netherlands Telephone number : +31 30 609 7406 Telefax number : +31 30 609 7556 This report is in conformity with NEN-EN-ISO/IEC 17025. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p03 Page 3 of 5 Table of contents 1 Exterior photographs ..............................................................................................................................................................4 1.1 Top view.........................................................................................................................................................................4 1.2 Bottom view ...................................................................................................................................................................5 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p03 Page 4 of 5 1 Exterior photographs 1.1 Top view Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p03 Page 5 of 5 1.2 Bottom view

FCC ID: IMR1106CB Label information Agere model 1106 (32-bits Cardbus interface): FCC ID: IMR1106CB Label information Agere model 1106 (16-bits Cardbus interface):

Testing and certification of electric, electronic and radio equipment/installations including telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Web: www.eps.tno.nl Project number: 04061405.p04 Page 1 of 6 INTERIOR PHOTOGRAPHS OF A 2.4/5 GHZ IEEE 802.11g/a WLAN CARDBUS CARD, BRAND AGERE, MODEL 1106 (32-BITS CARDBUS INTERFACE). FCC listed Industry Canada VCCI registered : : : 90828 IC3501 R-1518, C-1598 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p04 Page 2 of 6 Description of test item Test item : 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Manufacturer : Agere Systems Nederland B.V. Brand : Agere Model : 1106 (32-bits Cardbus interface) Serial numbers : 04NG22910024 and 04NG28910012 Revision : D1 & D2 Receipt number : 1 Receipt date : June 14, 2004 and July 21, 2004 Applicant information Applicant's representative : Mr. F. Hoekstra Company : Agere Systems Nederland B.V. Address : Zadelstede 1-10 Postal code : 3431 JZ City : Nieuwegein PO-box : 755 Postal code : 3430 AT City : Nieuwegein Country : The Netherlands Telephone number : +31 30 609 7406 Telefax number : +31 30 609 7556 This report is in conformity with NEN-EN-ISO/IEC 17025. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p04 Page 3 of 6 Table of contents 1 Interior photographs ...............................................................................................................................................................4 1.1 Top view PCB with shielding.........................................................................................................................................4 1.2 Top view PCB without shielding ...................................................................................................................................5 1.3 Bottom view PCB...........................................................................................................................................................6 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p04 Page 4 of 6 1 Interior photographs 1.1 Top view PCB with shielding Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p04 Page 5 of 6 1.2 Top view PCB without shielding Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p04 Page 6 of 6 1.3 Bottom view PCB

Testing and certification of electric, electronic and radio equipment/installations including telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Web: www.eps.tno.nl Project number: 04061405.p05 Page 1 of 6 INTERIOR PHOTOGRAPHS OF A 2.4/5 GHZ IEEE 802.11g/a WLAN CARDBUS CARD, BRAND AGERE, MODEL 1106 (16-BITS CARDBUS INTERFACE). FCC listed Industry Canada VCCI registered : : : 90828 IC3501 R-1518, C-1598 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p05 Page 2 of 6 Description of test item Test item : 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Manufacturer : Agere Systems Nederland B.V. Brand : Agere Model : 1106 (16-bits Cardbus interface) Serial numbers : 04NG3100004 Revision : D2 Receipt number : 1 Receipt date : July 28, 2004 Applicant information Applicant's representative : Mr. F. Hoekstra Company : Agere Systems Nederland B.V. Address : Zadelstede 1-10 Postal code : 3431 JZ City : Nieuwegein PO-box : 755 Postal code : 3430 AT City : Nieuwegein Country : The Netherlands Telephone number : +31 30 609 7406 Telefax number : +31 30 609 7556 This report is in conformity with NEN-EN-ISO/IEC 17025. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p05 Page 3 of 6 Table of contents 1 Interior photographs ...............................................................................................................................................................4 1.1 Top view PCB with shielding.........................................................................................................................................4 1.2 Top view PCB without shielding ...................................................................................................................................5 1.3 Bottom view PCB...........................................................................................................................................................6 Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p05 Page 4 of 6 1 Interior photographs 1.1 Top view PCB with shielding Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p05 Page 5 of 6 1.2 Top view PCB without shielding Description of EUT: Manufacturer: Brand mark: Model: FCC ID: 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Nederland B.V. Agere 1106 IMR1106CB Project number: 04061405.p05 Page 6 of 6 1.3 Bottom view PCB

Testing and certification of electric, electronic and radio equipment/installations including telecommunication systems TNO Electronic Products & Services (EPS) B.V. P.O. Box 15 9822 ZG Niekerk (NL) Smidshornerweg 18 9822 TL Niekerk (NL) Telephone: +31 594 505005 Telefax: +31 594 504804 E-mail: [email protected] Web: www.eps.tno.nl Project number: 04061405.ev1 Page 1 of 86 TEST REPORT OF A 2.4/5 GHZ IEEE 802.11a/g WLAN CARDBUS CARD, BRAND AGERE, MODEL 1106, IN CONFORMITY WITH FEDERAL REGULATED SAR (SPECIFIC ABSORPTION RATE) REQUIREMENTS IN THE USA AND CANADA. FCC listed Industry Canada VCCI registered : : : 90828 IC3501 R-1518, C-1598 Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: FCC/CA SAR Requirements 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Netherlands BV Agere 1106 IMR1106CB Project number: 04061405.ev1 Page 2 of 86 Description of test item Test item : 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Manufacturer : Agere Systems Nederland B.V. Brand : Agere Model : 1106 Serial numbers : 04NG12910086 Revision : n.a. Receipt number : 4 Receipt date : February 12, 2004 Applicant information Applicant's representative : Mr. A. Visee Company : Agere Systems Nederland B.V. Address : Zadelstede 1-10 Postal code : 3431 JZ City : Nieuwegein PO-box : 755 Postal code : 3430 AT City : Nieuwegein Country : The Netherlands Telephone number : +31 30 609 7534 Telefax number : +31 30 609 7556 Test(s) performed Location : Niekerk Test(s) started : June 15, 2004 Test(s) completed : June 24, 2004 Purpose of test(s) : To verify compliance with Federal regulated SAR requirements in the US and Canada Test specification(s) IEEE C95.1-1991, FCC OET Bulletin 65 (Supplement C), Industry Canada RSS-102 (Issue 1) Test engineer : J. Schuurmans, B.Sc.E.E. Project leader : H.J. Pieters Report written by : J. Schuurmans, B.Sc.E.E. Report approved by : P. de Beer Report date : July 4, 2004 This report is in conformity with NEN-EN-ISO/IEC 17025: 2000. This report shall not be reproduced, except in full, without the written permission of TNO Electronic Products & Services (EPS) B.V. The test results relate only to the item(s) tested. Test specification(s): Description of EUT: Manufacturer: Brand mark: Model: FCC ID: FCC/CA SAR Requirements 2.4/5 GHz IEEE 802.11g/a WLAN Cardbus card Agere Systems Netherlands BV Agere 1106 IMR1106CB Project number: 04061405.ev1 Page 3 of 86 Table of contents 1 General. .................................................................................................................................................................................6 1.1 Purpose of tests. .............................................................................................................................................................6 1.2 Applied standards/publications. .....................................................................................................................................6 1.3 References..........................................................................................................................…

Text truncated - open the document above for the full version.