J3OWSAP2000WLAN Accesspoint

1 Overview Welcome to the Intel® PRO/Wireless 5000 LAN Access Point User's Guide. This guide covers software installation, configuration, and troubleshooting. To select a topic, click a link in the contents column to the left. After installing the access point register your access point online. Go to the Intel Product Registration Web site. Copyright © 2002 Intel Corporation. Legal Information Introduction The 802.11a and 802.11b Intel® PRO/Wireless 5000 LAN Dual Access Point operates in the both 5 GHz and 2.4 GHz environment at speeds up to 54 Mbps (802.11a) and 11 Mbps (802.11b). It features a software configurable antenna and will supports IEEE 802.3af Power over Ethernet. Each access point uses eight non-overlapping transmission channels for support of up to 64 active users per access point. Placement can be on a desk or table, mounting on a wall or ceiling. The PRO/Wireless 5000 LAN Access Point is compatible with other products supporting the IEEE 802.11a standard and 802.11b standard. Security features include support for 128, 64, and 0-bit Wired Equivalent Privacy (WEP) encryption and Virtual Private Network (VPN) compatibility. A browser-based user interface is provided for configuration of the access point. See the installation instructions for information on how to set up and configure one or more access points. For information on how to set up a wireless LAN, see the Administrator's Guide . The Administrator's Guide is intended for use by network administrators. 802.1x Authentication The 802.11a Intel® PRO/Wireless 5000 LAN Dual Access Point supports 802.1x authentication for Windows operating systems. 802.1x authentication for wireless LANs has three main components: The supplicant (usually the client software); the authenticator (the access point); and the authentication server (usually a Remote Authentication Dial-In User Service or RADIUS server). 802.1x is a standards-based solution for port-level authentication for a wired or wireless Ethernet client systems. Copyright © 2002 Intel Corporation. Legal Information 2 Installation • Introduction • Installation Options and Requirements • Connect and Power Up the Access Point • LED Indicators • Configuring the Access Point for the First Time • Using DHCP • Access Point Default Values • Restore Factory Defaults • Select a Location for Installation of the Access Point • Access Point Configuration Introduction Your Intel® PRO/Wireless 5000 LAN Access Point, when used with Intel PRO/Wireless 5000 LAN Adapters or other 802.11a and 802.11b-compliant wireless LAN adapters, offers an easy and economical way to add secure wireless connectivity to a wired local area network (LAN) within a building or office. For detailed hardware installation requirements and diagrams, see the printed Quick Installation Guide supplied with the access point. Installation Options and Requirements Review the following options and requirements for installation and configuration of the access point for connection over the wired LAN: • (Recommended) For configuration of the access point, you will need a wired client workstation connected to the access point directly (recommended) or over the wired LAN to which the access point is connected. Note: Initial setup and configuration must be done over a wired connection, but subsequent changes to the configuration can be done over a wireless connection. • (Optional) DHCP server support for automatic assignment of an IP address to the access point over the wired network. You can configure the access point to use DHCP to get its IP address. See Using DHCP . Connect and Power Up the Access Point Connect the Access Point to the Wired Network • Plug an RJ-45 Category 5 Ethernet cable into the RJ-45 connector on the bottom of the access point and into a 10/100 Ethernet wall connector or hub. 3 Connect the Access Point to a Source of AC Power • Plug the power adapter into a wall outlet. • Plug the power adapter cable into the power socket on the bottom of the access point. LED Indicators Once the access point is connected to a wired network and is powered on, check the LED indicators to verify that the unit is functioning correctly. If the access point fails to initialize, restart it by disconnecting and reconnecting the power. The Intel® PRO/Wireless 5000 LAN Access Point can be mounted "right side up" on a desk or table or "upside down" on a wall or ceiling. The LED discussion that follows is based on a wall- or ceiling-mounted configuration in which the access point is "upside down." In this configuration the "Ready" LED will be the top LED and "Wired link" will be the bottom LED. • The "Ready" LED should be lit. • If the access point is connected to a LAN through an Ethernet cable, the "Wired link" LED should be lit (green for 10 Mbps, orange for 100 Mbps) and the "Wired network activity" LED should be blinking. • If the access point is communicating with a wireless adapter, the "Wireless radio activity" LED should be flashing steadily. The Wireless radio activity LED blinks faster when the access point is sending or receiving information from a wireless adapter. • Note that there are two sets of LEDs for "Wireless radio activity" and "Wireless radio association." The description indicates which models use which set or sets. Viewed on a wall- or ceiling-mounted access point, the LED indicators have the following locations and functions. Ready Green. This indicator will stay illuminated after the access point has completed the initialization sequence. The Ready light flashes quickly 3 times during a reset to factory default settings . Wireless radio activity (802.11a) Yellow flashes steadily if no adapter associated, and more rapidly when transferring data. Applies to models WSAP5000 and WDAP5000. Wireless radio association (802.11a) Green will be ON if a client is associated to the access point and OFF if not. Applies to models WSAP5000 and WDAP5000. Wireless radio activity (802.11b) Yellow flashes steadily if no ada…

Text truncated - open the document above for the full version.

File: R47372 May 28, 2002 American TCB 6731 Whittier Ave. Suite C110 McLean, VA. 22101 Gentlemen: The enclosed documents constitute a formal submittal and application for a Grant of Equipment Authorization pursuant to Subpart C of Part 15 of FCC Rules (CFR 47) regarding intentional radiators. Data within this report demonstrates that the equipment tested complies with the FCC limits for intentional radiators. Elliott Laboratories, as duly authorized agent prepared this submittal. A copy of the letter of our appointment as agent is enclosed. If there are any questions or if further information is needed, please contact Elliott Laboratories for assistance. Sincerely, Juan Martinez Senior EMC Engineer JM/dmg Enclosures:Emissions Test Report with Exhibits

Front Side of the Dual Accesspoint (WDAP5000) Back side of the Dual Accesspoint (WDAP5000) Bottom Side of the Dual Accesspoint (WDAP5000)

A/W #832-2668-001 A Master 2.3 WSAP5000 FAB #830-1770-001 ECN 23512 R-LARN-01-0202 C US LISTED E178682 E178682 I.T.E.I.T.E. U L Approved by IDA for use in Singapore. DB02941 HHHHAAAA-FFFF GZAEXXXX NYAEXXXX D01-XXXXJP 2.4 DS 4 90LP0011 Intel® PRO/Wireless 2000 LAN Access Point Model WSAP2000 .65" FOR HOME OR OFFICE USE Tested to Comply with FCC Standards FCC ID: J30WSAP2000 CANADA ICES/NMB-003 Class/Classe (B) Canada: XXX XXXX XXXXA SCT TTDXIMXXX-XXX CNC XX-XXXX Malaysia sticker INPUT: + 5.0 VDC 2.5A Printed By: Robert PaxmanReference Only unless DC stampedDate Printed: 07-Nov-2001 11:49:12 Number: 835-0115-001Rev: 01 23881Status: Prototype

A/W #C10033-001 Rev. 1 FAB #C10033 WSAP2000 Approved by IDA for use in Singapore. DB02941 Intel® PRO/Wireless 2000 LAN Access Point Model WSAP2000 C US LISTED E178682 I.T.E. U L This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation FCC ID: J30WSAP2000 CANADA ICES/NMB-003 Class/Classe (B) INPUT: + 5.0 VDC 2.5A 0336 Printed By: Robert PaxmanReference Only unless DC stampedDate Printed: 07-Nov-2001 11:49:12 Number: 835-0115-001Rev: 01 23881Status: Prototype

Internal Picture with partial assembly Front Side LED (Exterior Shield) Half shield removed, exposing the Front Side of AP Motherboard (LED Side) Front Side of AP motherboard showing the 2.4 GHz Mini PCI card and interconnection to antenna. Back Side of AP Motherboard showing the 5 GHz Mini PCI card and interconnection to antenna 2.4 GHz MINI PCI card front side with shield 2.4 GHz Mini PCI card front side with shield removed 2.4 GHz Mini PCI card back side Front Side of AP Motherboard (LED Side) were the 2.4 GHz Mini PCI will be installed Back side of AP motherboard were the 5 GHz Mini PCI will be installed Front Side of Antenna Back Side of Antenna

2/11/2002 2:57:58 PM Company Proprietary Created by: Robert Paxman 100-0903-004 BOM EXPLOSION REPORT PCBA,M3AWEB,OPTIONS:A,B 01 Part Number Part Description Part Revision LevelPart TypeItem NumberRevPart DescriptionFind Num QtyRef DesNotes 0Part100-0903-004PCBA, M3AWEB, OPTIONS:A, B .1Part100-SPEC-001ASPEC, QA REQUIREMENTS, PCBA50Ref Doc .1Part200-0903-003APCB, M3AWEB56GA301 ..2Part200-SPEC-001BSPEC, QA REQUIREMENTS, PCB100 .1Part230-0182-001ARF SHIELD FRAME, M3AWEB56GA361 .1Part600-0350-001A1CAP, X7R, 0.1uF, 10%, 16V, 0603 (602433-002)6038C1, C4, C7, C8, C10, C14, C15, C19- C21, C25, C30-C32, C35, C40-C42, C57, C70-C72, C81, C84, C89, C90, C93, C104, C108, C112, C113, C117, C121, C122, C124, C133, C135, C137 .1Part600-0306-001A1CAP, C0G, 1.0pF, +/-.25pF, 50V, 0402, T=0.60mm MAX 702C2, C12 .1Part600-0207-001A1CAP, C0G, 10pF, +/-.5pF, 6V, 0402, T=0.61mm MAX804C6, C51, C52, C105 .1Part601-0054-001ACAP, TANT, 10uF, 20%, 6.3V, 0805, EIA 2012 (R)908C9, C34, C38, C43, C102, C129, C134, C136 .1Part600-0309-001A1CAP, X7R, 220pF, 10%, 50V, 0402, T=0.60mm MAX1007C3, C39, C44-C47, C74 .1Part600-0205-001A4CAP, X7R, 0.01uF, 10%, 16V, 0402, T=0.60mm MAX11010C16, C17, C22, C53, C63, C92, C99, C114, C125, C130 .1Part600-0302-001A1CAP, X7R, 1000pF, 10%, 50V, 0402, T=0.60mm MAX12014C23, C29, C50, C60, C61, C76, C80, C86, C95, C98, C101, C106, C116, C128 Page 1 of 6 2/11/2002 2:58:02 PM Company Proprietary Created by: Robert Paxman 100-0903-004 BOM EXPLOSION REPORT PCBA,M3AWEB,OPTIONS:A,B 01 Part Number Part Description Part Revision LevelPart TypeItem NumberRevPart DescriptionFind Num QtyRef DesNotes .1Part600-0206-001A1CAP, C0G, 22pF, 5%, 50V, 0402, T=0.61mm MAX1301C24 .1Part600-0324-001ACAP, C0G, 0.5pF, +/-.25pF, 50V, 0402, T=0.55mm MAX 1402C87, C132 .1Part600-0311-001A1CAP, C0G, 7.0pF, +/-.5pF, 50V, 0402, T=0.55mm MAX15017C28, C36, C48, C59, C62, C65-C68, C77- C79, C83, C96, C97, C109, C111 .1Part600-0304-001A1CAP, C0G, 2.7pF, +/-.25pF, 50V, 0402, T=0.60mm MAX 1551C127 .1Part600-0325-001A2CAP, C0G, 5.0pF, +/-.25pF, 50V, 0402, T=0.60mm MAX 1602C49, C75 .1Part600-0313-001ACAP, C0G, 3.3pF, +/-.25pF, 50V, 0402, T=0.60mm MAX 1701C58 .1Part600-0312-001ACAP, C0G, 1.8pF, +/-.25pF, 50V, 0402, T=0.61mm MAX 1801C82 .1Part600-0330-001ACAP, C0G, 15pF, 5%, 50V, 0402, T=0.61mm MAX1902C69, C73 .1Part600-0204-001A1CAP, C0G, 100pF, 5%, 50V, 04022004C13, C85, C88, C94 .1Part600-0188-001A3CAP, X7R, 0.047uF, 10%, 16V, 06032102C27, C91 .1Part600-0317-001ACAP, X7R, 0.47uF, 10%, 16V, 0805, T=1.30mm MAX2201C100 .1Part600-0315-001B1CAP, X7R, 330pF, 10%, 50V, 0402, T=0.60mm MAX2301C103 .1Part600-0316-001ACAP, X7R, 6800pF, 10%, 16V, 0402, T=0.55mm MAX2401C107 .1Part600-0293-001ACAP, C0G, 68pF, 5%, 50V, 0402, T=0.022" MAX2502C110, C120 .1Part600-0303-001A1CAP, X7R, 0.068uF, 10%, 16V, 0603, T=0.90mm MAX2601C118 .1Part600-0300-001A1CAP, X7R, 0.68uF, 10%, 10V, 0805, T=1.30mm MAX2701C123 .1Part600-0314-001ACAP, X7R, 270pF, 10%, 50V, 0402, T=0.55mm MAX2801C126 .1Part702-0039-001AFILTER, SAW, 374.0MHz, SMD-84701FL1 .1Part702-0042-001AFILTER, LOWPASS, 2.45GHz, 3W, 08054801FL3 Page 2 of 6 2/11/2002 2:58:09 PM Company Proprietary Created by: Robert Paxman 100-0903-004 BOM EXPLOSION REPORT PCBA,M3AWEB,OPTIONS:A,B 01 Part Number Part Description Part Revision LevelPart TypeItem NumberRevPart DescriptionFind Num QtyRef DesNotes .1Part702-0040-001AFILTER, BANDPASS, 2.45GHz, 500mW, 12064902FL4, FL5 .1Part702-0041-001AFILTER, BANDPASS, 2.45GHz, 500mW, 12105001FL6 .1Part240-0364-001ACONN, ULTRA-MINI COAX, RCPT, SMD5102J1, J2 .1Part535-0144-001AIND, 560nH, 10%, 35mA, 1.55 OHM, 06035201L1 .1Part535-0143-001AIND, 4.7nH, +/-0.3nH, 0.3A, 0.25 OHM, 04025301L2 .1Part533-0049-001AFERRITE, CHIP, 30 OHM @ 100MHz, 3A, 08055402L3, L17 .1Part535-0155-001AIND, 39nH, 2%, 0.6A, 0.25 OHM, 06035501L5 .1Part535-0161-001AIND, 39nH, 5%, 0.5A, 0.6 OHM, 06035601L6 .1Part535-0138-001AIND, 2.7nH, +/-0.3nH, 300mA, 0.17 OHM, 04025701L7 .1Part535-0147-001AIND, 33nH, 2%, 0.6A, 0.22 OHMS, 06035802L9, L10 .1Part535-0139-001AIND, 33nH, 5%, 600mA, 0.55 OHM, 06035902L12, L14 .1Part533-0050-001AFERRITE CHIP, 120 OHM @ 100MHz, 120mA, 04026002L16, L18 .1Part535-0135-001AIND, 2.2nH, +/-0.3nH, 0.3A, 0.16 OHM, 04026101L19 .1Part535-0152-001AIND, 1.5nH, +/-0.3nH, 300mA, 0.13 OHM, 04026151L20 .1Part533-0002-001A4FERRITE CHIP, 600 OHM @ 100MHz, 200mA, 08056171L21 .1Part532-0084-001AXSTR, PNP, 2907, 60V, 600mA, 150mW, SOT3236501Q2 .1Part502-0225-001ARES CHP, 10K, 5%, 04026907R1, R11, R23, R26, R33, R41, R99 .1Part503-0221-001ARES CHP, 10M, 5%, 06037001R2 .1Part502-0239-001ARES CHP, 220K, 5%, 04027101R3 .1Part502-0242-001ARES CHP, 470 OHM, 5%, 04027202R13, R16 Page 3 of 6 2/11/2002 2:58:16 PM Company Proprietary Created by: Robert Paxman 100-0903-004 BOM EXPLOSION REPORT PCBA,M3AWEB,OPTIONS:A,B 01 Part Number Part Description Part Revision LevelPart TypeItem NumberRevPart DescriptionFind Num QtyRef DesNotes .1Part502-0001-001A5RES CHP, 0 OHM JUMPER, 04027305R5, R22, R82, R116, R118 .1Part502-0243-001ARES CHP, 560 OHM, 5%, 04027401R9 .1Part502-0220-001ARES CHP, 19.1K, 1%, 04027502R10, R14 .1Part502-0020-001A5RES CHP, 3.01K, 1%, 04027601R12 .1Part502-0057-001A1RES CHP, 1.50K OHM, 1%, 04027703R15, R37, R65 .1Part502-0009-001A5RES CHP, 100 OHM, 1%, 040278011R17, R18, R25, R31, R35, R42, R43, R47- R49, R51 .1Part502-0058-001A2RES CHP, 619 OHM, 1%, 04027901R28 .1Part502-0224-001ARES CHP, 976 OHM, 1%, 04028001R30 .1Part502-0088-001ARES CHP, 12.1K, 1%, 04028101R32 .1Part502-0154-001ARES CHP, 11.5K, 1%, 04028201R36 .1Part502-0218-001ARES CHP, 9.53K, 1%, 04028301R38 .1Part502-0219-001ARES CHP, 1.10K, 1%, 04028402R39, R44 .1Part502-0018-001A5RES CHP, 2.00K, 1%, 04028501R40 .1Part502-0221-001ARES CHP, 2.87K, 1%, 04028601R45 .1Part502-0023-001A5RES CHP, 4.64K, 1%, 04028701R50 .1Part502-0015-001A6RES CHP, 1.00K, 1%, 04028802R52, R71 .1Part502-0092-001A1RES CHP, 2.21K, 1%, 04028901R55 .1Part502-0227-001ARES CHP, 300 OHM, 5%, 04029001R56 .1Part502-0222-001ARES CHP, 124 OHM, 1%, 04029104R58, R62, R66, R67 .…

Text truncated - open the document above for the full version.

Technical Specification Sheet 5GHz 802.11a Antenna – 100-0932-001 General Description This dual band, 2.4GHz and 5.2GHz, antenna has been designed specifically for the WDAP5000 Access Product. It features 802.11a active antenna elements and 802.11b passive elements. The 802.11a antenna has two different emission patterns selectable via software control, omni and front half circle. To connect to the 802.11a active elements a 2mm UMP connector is used. A coaxial UFL connector is used to feed each of the 802.11b elements. Electrical Specifications 802.11a Array Frequency Range: 5.15 – 5.35 GHz Peak Gain: 1.8dBi Omni, 5.6dBi Pattern VSWR: less than 2.0:1 Polarization: Circular/Universal Azimuth Beam-width: Omni-directional/Pattern Power Handling: 10Watt CW Feed Point Impedance: 50 OHMS unbalanced 802.11b Elements Frequency Range: 2.41 – 2.49 GHz Peak Gain: 6.2dBi VSWR: less than 2.0:1 Polarization: Linear Azimuth Beam-width: Omni-directional Power Handling: 10Watt CW Feed Point Impedance: 50 OHMS unbalanced Mechanical Specifications Size: 6.378 x 2.467 x 0.123 Inches Weight: 1.5 oz Mounting: Snap on 12 pin Connector and slots MPE Calculations FCC part 1.1310, Table 1 limits the power density for uncontrolled exposure to 1mW/ cm 2 for systems operating in the UNII bands. The distance, d(cm) from the antenna at which the power density, P d (mW/cm 2 ) is below this limit is calculated from the maximum EIRP, P t (mW) using the equation: P d = P t /(4 ðd 2 ) Re-arranging for the distance at which the power density is 1mW/cm2 gives: d = √ (P t /(4 ð)) The device under test is designed to use an integral antenna with a gain of 6.2 dBi. The maximum output power for the two modes and all channels is dBm. The maximum EIRP is, therefore, 15.3 dBm + 6.2 dBi = 21.5 dBm (141.3 mW): d = √ (141.3 / (4 ð)) = 3.35 cm The distance from the antenna that the power density is 1mW/ cm 2 is, therefore, 3.39 cm. The users guide instructs the user to install the device such that it has a separation of at least 20cm from persons (see text below) to comply with the FCC’s requirements. This separation of 20cm more than meets the FCC’s and Industry Canada RF exposure requirements. ModeEIRPPd at 20cm Calculated distance (in cm) where Pd < 1mW/ cm 2 Normal 21.5 dBm (141.3 mW) 0.0281 mW/ cm 2 3.35 Extract From User’s Manual

FCC ID: M3AWEB56GA Report Number: B11108D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 1 of 23 FCC PART 15, SUBPART C TEST METHOD: ANSI C63.4-1992 for MPCI TYPE 3A 802.11B WIRELESS + V.92 MODEM CARD Model: M3AWEB56GA Prepared for XIRCOM, INC. 2300 CORPORATE CENTER DRIVE THOUSAND OAKS, CALIFORNIA 91320 COMPATIBLE ELECTRONICS INC. 114 OLINDA DRIVE BREA, CALIFORNIA 92823 (714) 579-0500 DATE: NOVEMBER 13, 2001 REPORT APPENDICES TOTAL BODY A B C D PAGES 23 2 2 14 51 92 This report shall not be reproduced except in full, without the written approval of Compatible Electronics. FCC ID: M3AWEB56GA Report Number: B11108D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 2 of 23 TABLE OF CONTENTS Section / Title PAGE GENERAL REPORT SUMMARY 4 1. PURPOSE 6 2. ADMINISTRATIVE DATA 7 2.1 Location of Testing 7 2.2 Traceability Statement 7 2.3 Cognizant Personnel 7 2.4 Date Test Sample was Received 7 2.5 Disposition of the Test Sample 7 2.6 Abbreviations and Acronyms 7 3. APPLICABLE DOCUMENTS 8 4. Description of Test Configuration 9 4.1 Description of Test Configuration - EMI 9 4.1.1 Cable Construction and Termination 10 5. LISTS OF EUT, ACCESSORIES AND TEST EQUIPMENT 11 5.1 EUT and Accessory List 11 5.2 EMI Test Equipment 12 6. TEST SITE DESCRIPTION 14 6.1 Test Facility Description 14 6.2 EUT Mounting, Bonding and Grounding 14 7. CHARACTERISTICS OF THE TRANSMITTER 15 7.1 Transmitter Power 15 7.2 Channel Number and Frequencies 15 7.3 Chipping Rate 15 7.4 Spreading Gain 15 7.5 Antenna Gain 15 7.6 Processing Gain 16 8. Test Procedures 17 8.1 RF Emissions 17 8.1.1 Conducted Emissions Test 17 8.1.2 Radiated Emissions (Spurious and Harmonics) Test 18 8.2 6 dB Bandwidth for Direct Sequence Systems 20 8.3 Peak Output Power 20 8.4 Spectral Density Output 20 8.5 RF Antenna Conducted Test 21 8.6 RF Band Edges 21 8.7 Processing Gain 22 9. CONCLUSIONS 23 FCC ID: M3AWEB56GA Report Number: B11108D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 3 of 23 LIST OF APPENDICES APPENDIX TITLE A Modifications to the EUT B Additional Models Covered Under This Report C Diagrams, Charts and Photos • Test Setup Diagrams • Radiated and Conducted Emissions Photos • Antenna and Effective Gain Factors D Data Sheets LIST OF FIGURES FIGURE TITLE 1 Conducted Emissions Test Setup 2 Plot Map And Layout of Test Site FCC ID: M3AWEB56GA Report Number: B11108D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 4 of 23 GENERAL REPORT SUMMARY This electromagnetic emission test report is generated by Compatible Electronics Inc., which is an independent testing and consulting firm. The test report is based on testing performed by Compatible Electronics personnel according to the measurement procedures described in the test specifications given below and in the "Test Procedures" section of this report. The measurement data and conclusions appearing herein relate only to the sample tested and this report may not be reproduced without the written permission of Compatible Electronics, unless done so in full. This report must not be used to claim product endorsement by NVLAP or any other agency of the U.S. Government. Device Tested: MPCI Type 3A 802.11B Wireless + V.92 Modem Card Model: M3AWEB56GA S/N: N/A Modifications: The EUT was not modified in order to meet the specifications. Manufacturer: Xircom, Inc. 2300 Corporate Center Drive Thousand Oaks, California 91320 Test Date: November 8, 2001 File # For Canada IC2154-D Test Specifications : EMI requirements FCC Title 47, Part 15 Subpart B; and Subpart C, sections 15.205, 15.207, 15.209, and 15.247 Test Procedure: ANSI C63.4: 1992 Test Deviations: The test procedure was not deviated from during the testing. FCC ID: M3AWEB56GA Report Number: B11108D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 5 of 23 SUMMARY OF TEST RESULTS TEST DESCRIPTION RESULTS 1 Conducted RF Emissions, 450 kHz – 30 MHz Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.207 2 Spurious Radiated RF Emissions, 10 kHz – 25000 MHz Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.247(c) 3 Fundamental and Emissions produced by the intentional radiator in non-restricted bands, 10 kHz – 25 GHz Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.247(c) 4 Emissions produced by the intentional radiator in restricted bands, 10 kHz – 25 GHz Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.205 and 15.209(a) 5 6 dB Bandwidth Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.247 (a)(2) 6 Maximum Peak Output Power Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.247 (b)(1) 7 RF Antenna Conducted Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.247 (c) 8 Peak Power Spectral Density Conducted from the Intentional Radiator to the Antenna Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.247 (d) 9 Processing Gain Complies with the relevant requirements of FCC Title 47, Part 15, Subpart C, section 15.247 (e) FCC ID: M3AWEB56GA Report Number: B11108D1 114 OLINDA DRIVE, BREA, CALIFORNIA 92823 PHONE: (714) 579-0500 FAX: (714) 579-1850 Page 6 of 23 1. PURPOSE This document is a qualification test report based on the Electromagnetic Interference (EMI) tests performed on the MPCI Type 3A 802.11B Wireless + V.92 Modem Card Model: M3AWEB56GA. Only the RF module itself is being approved. The EMI measurements were performed according to the measurement procedure described in ANSI C63.4: 1992. The tests were performed in order to determine whether the electromagnetic emissions from the MPCI Type 3A 802.11B Wireless + V.92 Modem Card, referred to as EUT hereafter,…

Text truncated - open the document above for the full version.

File: R47372 May 28, 2002 American TCB 6731 Whittier Ave. Suite C110 McLean, VA. 22101 Gentlemen: The enclosed documents constitute a formal submittal and application for a Grant of Equipment Authorization pursuant to Subpart C of Part 15 of FCC Rules (CFR 47) regarding intentional radiators. Data within this report demonstrates that the equipment tested complies with the FCC limits for intentional radiators. Elliott Laboratories, as duly authorized agent prepared this submittal. A copy of the letter of our appointment as agent is enclosed. If there are any questions or if further information is needed, please contact Elliott Laboratories for assistance. Sincerely, Juan Martinez Senior EMC Engineer JM/dmg Enclosures:Emissions Test Report with Exhibits File: R47372 Page 1 of 15 Electromagnetic Emissions Test Report and Application for Grant of Equipment Authorization pursuant to FCC Part 15, Subpart C Specifications for an Intentional Radiator on the Intel Corporation Models: WSAP2000 FCC ID:J3OWSAP2000 GRANTEE:Intel Corporation 2300 Corporate Center Drive Thousand Oaks, CA 91320 TEST SITE:Elliott Laboratories, Inc. 684 W. Maude Avenue Sunnyvale, CA 94086 REPORT DATE:May 28, 2002 FINAL TEST DATE:January 21, 2002 AUTHORIZED SIGNATORY:______________________________ Juan Martinez Senior EMC Engineer This report shall not be reproduced, except in its entirety, without the written approval of Elliott Laboratories, Inc. Elliott Laboratories, Inc. -- EMC DepartmentTest Report Report Date: May 28, 2002 File: R47372Page 2 of 15 pages TABLE OF CONTENTS COVER PAGE..................................................................................................................................................................................1 TABLE OF CONTENTS.................................................................................................................................................................2 SCOPE...............................................................................................................................................................................................3 OBJECTIVE.....................................................................................................................................................................................3 STATEMENT OF COMPLIANCE................................................................................................................................................3 EMISSION TEST RESULTS.........................................................................................................................................................4 LIMITS OF CONDUCTED INTERFERENCE VOLTAGE....................................................................................................4 LIMITS OF ANTENNA CONDUCTED POWER.....................................................................................................................4 LIMITS OF RADIATED INTERFERENCE FIELD STRENGTH..........................................................................................4 LIMITS OF POWER AND BANDWIDTH.................................................................................................................................5 MEASUREMENT UNCERTAINTIES.......................................................................................................................................5 EQUIPMENT UNDER TEST (EUT) DETAILS............................................................................................................................6 GENERAL....................................................................................................................................................................................6 ENCLOSURE...............................................................................................................................................................................6 MODIFICATIONS.......................................................................................................................................................................7 SUPPORT EQUIPMENT...........................................................................................................................................................7 EXTERNAL I/O CABLING.........................................................................................................................................................7 EUT OPERATION DURING EMISSIONS...............................................................................................................................7 TEST SITE........................................................................................................................................................................................8 GENERAL INFORMATION.......................................................................................................................................................8 RADIATED EMISSIONS CONSIDERATIONS.......................................................................................................................8 MEASUREMENT INSTRUMENTATION....................................................................................................................................9 INSTRUMENT CONTROL COMPUTER.................................................................................................................................9 LINE IMPEDANCE STABILIZATION NETWORK (LISN)...................................................................................................9 POWER METER..........................................................................................................................................................................9 FILTERS/ATTENUATORS.......................................................................................................................................................10 ANTENNAS…

Text truncated - open the document above for the full version.

File: R47372 May 28, 2002 American TCB 6731 Whittier Ave. Suite C110 McLean, VA. 22101 Gentlemen: The enclosed documents constitute a formal submittal and application for a Grant of Equipment Authorization pursuant to Subpart C of Part 15 of FCC Rules (CFR 47) regarding intentional radiators. Data within this report demonstrates that the equipment tested complies with the FCC limits for intentional radiators. Elliott Laboratories, as duly authorized agent prepared this submittal. A copy of the letter of our appointment as agent is enclosed. If there are any questions or if further information is needed, please contact Elliott Laboratories for assistance. Sincerely, Juan Martinez Senior EMC Engineer JM/dmg Enclosures:Emissions Test Report with Exhibits File: R47372 Page 1 of 15 El…

Text truncated - open the document above for the full version.