J69CB526Shopper Call Box

Technical Document 430668-00 Rev. E Indyme Solutions, Inc. 8295 Aero Place  San Diego, CA 92123 USA +1.858.268.0717  +1.800.829.6141Page 1 of 2 CB526 Pocket Director Call Box Programming the CB526: If at any point during the programming sequence 30 seconds expire without a button being pressed, the address programming mode will be exited and the previously programmed address will continue to be used. The assurance LED will flash 5 times to indicate that mode programming has been exited. 1. Press and hold button 2 for 5 seconds. The assurance LED will flash once. 2. Press and hold button 1 for 5 seconds. The assurance LED will flash twice. 3. Press and hold button 2 for 5 seconds. The assurance LED will flash three times. 4. Press button 1 once. 5. Press button 2 once, the assurance LED will flash once. You are now in Address Programming Mode. 6. To program the hundreds value, press button one 1-9 times. 7. Press button two, one time to save the hundreds value. 8. To program the tens value, press button one 1-9 times. 9. Press button two, one time to save the tens value. 10. To program the ones value, press button one 1-9 times. 11. Press button two, one time to save the ones value. The assurance LED will now flash back the address that was programmed. NOTE: To program the number zero (“0”) do not press button 1, instead, press 2. During the flash back sequence, the LED indicates a zero by staying on longer. The CB526 is a mini director call box designed for pocket or clip-on use. The 4-membrane switch assembly is designed without a reset button and is intended to be carried by store employees desiring to trigger messages from various locations within the store. The CB526 call box has a single assurance LED, it will flash for ¼-sec when a button is pressed. Technical Document 430668-00 Rev. E Indyme Solutions, Inc. 8295 Aero Place  San Diego, CA 92123 USA +1.858.268.0717  +1.800.829.6141Page 2 of 2 FCC Notice of Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Class B statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Correspondence by Project Project Number: Correspondence Number Memo J69CB526-1 1) Please provide a TCB contract. A TCB contract has been provided. 2) Please provide a diagram or photo showing the location of the FCC ID label. A sample diagram showing the label location has been provided. 3) The test report does not mention whether testing was performed below 30 MHz. Please clarify whether testing was performed below 30 MHz and the results. Testing was performed below 30 MHz and no emissions were found. 4) Please provide documentation to show RF exposure compliance. A document explaining SAR exclusion has been provided. 5) Please provide external photos. Please see the external photos that have been provided. 6) Please provide internal photos. Please see the internal photos that have been provided. 7) The user manual states that a supervisory transmission is sent, however the test report states that the EUT has no supervision transmissions. Please provide clarification regarding the operation of the device and provide updated documentation as required. Supervisory transmissions are not used, please see the amended user manual. Untitled Documenthttp://www.celectronics.com/CorrespondenceByProject.asp?ProjectNum... 1 of 11/17/2014 8:49 AM

EUT Front EUT Rear

I n d y m e S o l u t i o n s , I n c . P A T . 4 , 7 4 1 , 0 2 0 © 2 0 0 9 M o d e l N 2 0 1 Indyme Solutions • Part #260135-01 • Model No. N201 • 05/13/09 Scale 1:1 Scale 2:1 FCC ID:J69CB526 I n d y m e S o l u t i o n s , I n c . P A T . 4 , 7 4 1 , 0 2 0 © 2 0 0 9 M o d e l N 2 0 1 FCC ID:J69CB526

PCB Front PCB Back

4/21/09 1 2 3 12 13 6 8 11 9 7 4 10 5 6 7 Larry OFred A 5/18/095/18/09 430667-00 CB526 Assembly Document A REVISIONS REV. DESCRIPTION DATE APPROVED A Release for Review 5/18/09 DATE SIZE CAGE CODE DWG NO. SCALE B THIS DOCUMENT IS THE PROPERTY OF INDYME CORPORATION AND IS CONSIDERED COMPANY CONFIDENTIAL. THE REPRODUCTION OR USE OF INFORMATION HEREIN, ALL OR IN PART, IS EXPRESSLY PROHIBITED WITHOUT WRITTEN CONFIRMATION FROM A PRINCIPAL MEMBER OF MANAGEMENT AT INDYME. Sheet 1 of 2 1:1 Temp_b.slddrt FILE NAME:230617-00_A CB526 3-18-09.SLDPRT COMMENTS APPROVALS DRAWN CHECKED ENG APPR. MFG APPR. 63 μINCH INTERPRET GEOMETRIC TOL PER: ASME Y14.100 - 2000 .X.XX.XXX.XXXX FINISH MATERIAL DO NOT SCALE DRAWING UNLESS OTHERWISE SPECIFIEDDIMENSION TOLERANCES ARE:DECIMAL INCHES ANGLES DIMENSIONS ARE IN INCHES ± .031± .015± .005± .0001 ± 0.5 º Sheet1 OF 2 REV. DRW NO. THIS DRAWING MAY NOT CONTAINALL THE DIMENSIONS NECESSARY TO TOOLOR MANUFACTURE THIS PART. FOR ACCURATE DIMENSIONS, CONTOURS AND FEATURES,REFER TO THE 3D COMPUTER MODEL CREATEDIN SOLIDWORKS 2009 indyme solutions THIRD ANGLEPROJECTION G King A B Install Batteries as illustrated Install double sided adhesive to belt clip as illustrated then place in bag with instructions. "Do not remove adhesive cover this side, Do not attach to 526" When Installing overlay use tabsalign overlay on face of plasticto start overlay attachment process When installing PCA Align antenna such that it is 1. captured by post as illustrated 2. Antenna must be flat along back of membrane full lengthand Not touch PCA other than solder point 430667-00 CB526 Assembly Document A Install labels as illustrated DATE SIZE CAGE CODE DWG NO. SCALE B THIS DOCUMENT IS THE PROPERTY OF INDYME CORPORATION AND IS CONSIDERED COMPANY CONFIDENTIAL. THE REPRODUCTION OR USE OF INFORMATION HEREIN, ALL OR IN PART, IS EXPRESSLY PROHIBITED WITHOUT WRITTEN CONFIRMATION FROM A PRINCIPAL MEMBER OF MANAGEMENT AT INDYME. Sheet 2 of 2 1:1 Temp_b.slddrt FILE NAME:230617-00_A CB526 3-18-09.SLDPRT COMMENTS APPROVALS DRAWN CHECKED ENG APPR. MFG APPR. 63 μINCH INTERPRET GEOMETRIC TOL PER: ASME Y14.100 - 2000 .X.XX.XXX.XXXX FINISH MATERIAL DO NOT SCALE DRAWING UNLESS OTHERWISE SPECIFIEDDIMENSION TOLERANCES ARE:DECIMAL INCHES ANGLES DIMENSIONS ARE IN INCHES ± .031± .015± .005± .0001 ± 0.5 º Sheet2 OF 2 REV. DRW NO. THIS DRAWING MAY NOT CONTAINALL THE DIMENSIONS NECESSARY TO TOOLOR MANUFACTURE THIS PART. FOR ACCURATE DIMENSIONS, CONTOURS AND FEATURES,REFER TO THE 3D COMPUTER MODEL CREATEDIN SOLIDWORKS 2009 indyme solutions THIRD ANGLEPROJECTION G King

This device FCC ID: is excluded from SAR testing by the following justi fication The maximum power that the transmitter is capable o f is 10.00 mW Using the following formula from section 4.3.1 of K DB 447498 at test separation distances ≤ 50 mm [(max. power of channel, including tune-up toleranc e, mW) / (min. test separation distance, mm)] * [ √ f(GHz)] Duty Cycle 11.00% Value 1-g (mW) 10-g (mW) 1.10 181 589 "Value" is ≤ 3 , the SAR test exclusion threshold 1-g power limit 10-g power limit 272 680 “source-based” time-averaging based on an inherent property or duty-cycle of a device is allowed. An e xample of this is the determination of exposure from a device that uses d igital technology such as a time-division multiple- access (TDMA) scheme for transmission < 50mm power limits for above caclulation using spe cified frequency J69CB526 Max Peak Power (dBm) Min Separation distance (mm) Fre quency (Ghz) When the minimum test separation distance is < 5 mm , a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 0.3038 5 10

Nemko USA, Inc. 11696 Sorrento Valley Rd., Suite F San Diego, CA 92121-1024 Phone (858) 755-5525 Fax (858) 452-1810 FCC Part 15 Subpart C, 15.231: 23/09/2010 VERIFICATION TEST REPORT Report Number: 2009 06130094 FCC Project Number: 29282-1 Nex Number: 130094 Applicant: INDYME SOLUTIONS, INC. 9085 AERO DRIVE SAN DIEGO, CA 92123 USA Equipment Under Test (EUT): SHOPPER CALL BOX Model: CB526 In Accordance With: FCC Part 15 Subpart C, 15.231 FCC Part 15 Subpart C, 15.109 Tested By: Nemko USA Inc. 11696 Sorrento Valley Road, Suite F San Diego, CA 92121 Authorized By: Alan Laudani, EMC/RF Test Engineer Date: June 16, 2009 Total Number of Pages: 26 Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2009 06130094 FCC Specification: FCC Part 15 Subpart C, 15.231(e) Page 2 Section1: Summary of Test Results General All measurements are traceable to national standards These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with FCC Part 15; Subpart C. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. The assessment summary is as follows: Apparatus Assessed: Shopper Call Box Model: CB526 Specification: FCC Part 15 Subpart C, 15.231 FCC Part 15 Subpart C, 15.109 Date Received in Laboratory: June 15, 2009 Compliance Status: Complies Exclusions: None Non-compliances: None Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2009 06130094 FCC Specification: FCC Part 15 Subpart C, 15.231(e) Page 3 1.1 Report Release History REVISION DATE COMMENTS - June 16, 2009 Prepared By: Ferdinand Custodio - June 16, 2009 Initial Release: Alan Laudani NOTE: Nemko USA, Inc. hereby makes the following statements so as to conform to Chapter 10 (Test Reports) Requirements of ANSI C63.4 (2003) “Methods and Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz”: o The unit described in this report was received at Nemko USA, Inc.'s facilities on June 10, 2009. o Testing was performed on the unit described in this report on June 11, 2009 to June 19, 2009 o The Test Results reported herein apply only to the Unit actually tested, and to substantially identical Units. o This report does not imply the endorsement of the Federal Communications Commission (FCC), Industry Canada, NVLAP or any other government agency. This Report is the property of Nemko USA, Inc., and shall not be reproduced, except in full, without prior written approval of Nemko USA, Inc. However, all ownership rights are hereby returned unconditionally to Indyme Solutions, Inc., and approval is hereby granted to Indyme Solutions, Inc., and its employees and agents to reproduce all or part of this report for any legitimate business purpose without further reference to Nemko USA, Inc. TESTED BY: ___________________________________ Date: June 16, 2009 Ferdinand Custodio, EMC Test Engineer Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2009 06130094 FCC Specification: FCC Part 15 Subpart C, 15.231(e) Page 4 TABLE OF CONTENTS Section1: Summary of Test Results ............................................................................ 2 1.1 Report Release History ..................................................................................... 3 Section 2: Equipment Under Test ................................................................................ 5 2.1 Product Identification ........................................................................................ 5 2.2 Samples Submitted for Assessment ................................................................. 5 2.3 Theory of Operation .......................................................................................... 6 2.4 Technical Specifications of the EUT ................................................................. 6 Section 3: Test Conditions ........................................................................................... 7 3.1 Specifications .................................................................................................... 7 3.2 Deviations from Laboratory Test Procedures .................................................... 7 3.3 Test Environment .............................................................................................. 7 3.4 Test Equipment ................................................................................................. 8 Section 4: Observations ............................................................................................... 9 4.1 Modifications Performed During Assessment ................................................... 9 4.2 Record Of Technical Judgements ..................................................................... 9 4.3 EUT Parameters Affecting Compliance ............................................................ 9 4.4 Test Deleted ...................................................................................................... 9 4.5 Additional Observations .................................................................................... 9 Section 5: Results Summary ...................................................................................... 10 5.1 Test Results .................................................................................................... 10 Appendix A: Test Results ........................................................................................... 11 Section 15.109 – Radiated Emission Limits .................................................................. 11 Section 15.231(a)(1) – Transmitter deactivation within 5 seconds ................................ 13 Section 15.231…

Text truncated - open the document above for the full version.

Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2009 06130094 FCC Specification: FCC Part 15 Subpart C, 15.231(e) Page 22 Appendix B: Test Setup Photographs Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2009 06130094 FCC Specification: FCC Part 15 Subpart C, 15.231(e) Page 23 “X” Configuration Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2009 06130094 FCC Specification: FCC Part 15 Subpart C, 15.231(e) Page 24 “Y” Configuration Nemko USA, Inc. 11696 Sorrento Valley Road, Suite F, San Diego, CA 92121 Phone (858) 755-5525 Fax (858) 452-1810 Report Number: 2009 06130094 FCC Specification: FCC Part 15 Subpart C, 15.231(e) Page 25 “Z” Configuration