J9CFTD1DOG TRACKING COLLAR

Qualcomm Consumer Services Qualcomm Confidential and Proprietary Restricted Distribution. Not to be distributed to anyone who is not an employee of either Qualcomm or a subsidiary of Qualcomm without the express approval of Qualcomm’s Configuration Management. Model Number 10-H6795-P1 QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714 U.S.A. Copyright © 2011 QUALCOMM Incorporated. All Rights Reserved. Qualcomm Confidential and Proprietary Not to be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of Qualcomm. QUALCOMM is a registered trademark of QUALCOMM Incorporated in the United States and may be registered in other countries. Other product and brand names may be trademarks or registered trademarks of their respective owners. TAGG The Pet Tracker(TM) and the TAGG Logo are trademarks of Qualcomm Consumer Services Inc. Service Subscription Required. This technical data may be subject to U.S. and international export, re-export or transfer (“export”) laws. Diversion contrary to U.S. and international law is strictly prohibited. DRAFT 10-H6795-P1 April 14, 2011 Qualcomm Confidential and Proprietary iii -DRAFT May contain U.S. and international export controlled information Contents Tagg – The Pet Tracker™ ............................................................................................. 5 Description of the Product ........................................................................................... 5 In the Box ....................................................................................................................... 6 Tagg Device Overview .................................................................................................. 7 Docking Station Overview ............................................................................................ 9 Basic Setup .................................................................................................................. 11 Step 1: Update your account ........................................................................................................... 11 Step 2: Activate your Tagg device ................................................................................................... 12 Step 3: Add your pet ........................................................................................................................ 13 Step 4: Attach the Tagg tracker to the collar .................................................................................... 14 Step 5: Set up your notifications ...................................................................................................... 16 Step 6: Test your setup ................................................................................................................... 16 Troubleshooting setup ..................................................................................................................... 17 Adjusting the Tagg Zone ................................................................................................................. 17 Locating Your Pet........................................................................................................ 19 What to expect when your pet is home ............................................................................................ 19 Paging your pet ......................................................................................................................... 20 What to expect when your pet is inside the Tagg Zone .................................................................... 21 Initiating an on-demand locate .................................................................................................. 21 What to expect when your pet is outside the Tagg Zone .................................................................. 22 Initiating continuous tracking ..................................................................................................... 23 Viewing a pet’s trail ................................................................................................................... 23 What to expect when you take your pet for a walk ........................................................................... 24 Manage Your Devices ................................................................................................. 25 Manage Tagg Trackers ................................................................................................................... 25 Manage Docking Stations ................................................................................................................ 26 Mobile Phone Commands .......................................................................................... 27 Warnings and Safety Information .............................................................................. 28 Underwriters Laboratories (UL) Listing ............................................................................................. 28 DRAFT Contents Qualcomm Confidential and Proprietary iv-DRAFT May contain U.S. and international export controlled information Important Health Information and Safety Precautions ...................................................................... 28 Product Safety .......................................................................................................................... 28 Safety Precautions for Power Supply ........................................................................................ 28 Safety Precautions for Direct Sunlight ....................................................................................... 29 Keep the Docking Station Dry ................................................................................................... 29 Accessories ................................................................................…

Text truncated - open the document above for the full version.

Date: June 23, 2008 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Paul Guckian VP, EMC/Regulatory Engineering QUALCOMM Incorporated

Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: J9CFTD1 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Part List Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments up to 180 days. External Photos Internal Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Paul Guckian VP, Engineering Qualcomm Incorporated April 15, 2011

Exhibit 9 Tagg FTD External Photographs FCC Part 22 & 24 Certification FCC ID: J9CFTD1 Model: Tagg FTD STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Report Prepared by: QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714

Exhibit 8 Tagg FTD FCC Label and Location FCC Part 22 & 24 Certification FCC ID: J9CFTD1 Model: Tagg FTD STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Report Prepared by: QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714

Exhibit 10 Tagg FTD Internal Photographs FCC Part 22 & 24 Certification FCC ID: J9CFTD1 Model: Tagg FTD STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Report Prepared by: QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714

Exhibit 1A Tagg FTD Tune Up Procedure FCC Part 22 & 24 Certification FCC ID: J9CFTD1 Model: Tagg FTD STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Report Prepared by: QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714 Tune Up Procedure Requirement: §2.1033(c) (9) Tune-up procedure over the power range, or at specific operating power levels. All frequency and power adjustments are set at the factory and there are no field adjustments for this product. Under digital mode, frequency is locked to the base station and controlled by VCTCXO adjustments to offset any possible errors Qualcomm information:

FCC ID: J9CFTD1 MPE Analysis QUALCOMM Proprietary 1 Tagg FTD MPE Evaluation Report FCC Part 22 & 24 Certification FCC ID: J9CFTD1 Model: Tagg FTD STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Report Prepared by: QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714 FCC ID: J9CFTD1 MPE Analysis QUALCOMM Proprietary 2 In this application we seek modular approval for the Tagg FTD tracking device to be used in a mobile configuration. Based on the FCC CFR 47 §1.1310, 2.1091, we have concluded that the Tagg FTD tracking device will comply with the FCC rules on RF exposure for mobile devices if the antenna again does not exceed 7 dBi in cellular and 4 dBi in PCS. The following analysis will demonstrate such compliance. The analysis will be done in both cellular and PCS bands which operates in North American. RF Exposure Limit According to FCC CFR 47 §1.1310: the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b). Limits for Maximum Permissible Exposure (MPE) Friis Transmission Formula Friis transmission formula: P d = (P out * G) / (4πR 2 ) Where, P d = power density (mW/cm 2 ) P out = output power to antenna (mW) G = gain of antenna in linear scale R = distance between observation point and center of the radiator (cm) FCC ID: J9CFTD1 MPE Analysis QUALCOMM Proprietary 3 Tagg FTD Operating in Cellular Band (824 - 849 MHz) The highest peak conducted output power of the Tagg FTD tracking device measured in cellular band is 24.28 dBm while the device operates in CDMA channel 384. Take the worst case as an example, in which an antenna with 7dBi gain is used. The resulted power density at a distance of 20cm can be calculated as follows: EIRP = 24.28 + 7 = 31.28 dBm = 1342.7 mW Power Density = (EIRP * DutyCycle) / (4πR 2 ) = 1342.7 * 1 / (4*π* 20 2 ) = 0.267 mW/cm 2 Where DutyCycle is 1 for CDMA (the worst case) and R is 20cm. The MPE limit for General Population/Uncontrolled Exposure is shown in the table above and can be derived as follows: MPE limit = 824/1500 = 0.55mW/cm 2 As per the above analysis, the resulted power density is below the MPE limit. Therefore the Tagg FTD tracking device in cellular band is compliant with the FCC rules on RF exposure. Tagg FTD Operating in PCS Band (1850 - 1910 MHz) The highest peak conducted output power of Tagg FTD tracking device measured in PCS is 24.55 dBm while the Tagg FTD tracking device operates in CDMA channel 25. In the worst case, where an antenna gain is 4dBi, the resulted ERP can be expressed as follows: ERP = 24.55 + 4 - 2.15 = 26.4 dBm (0.437W) < 3 W In FCC CFR 47 §2.1091, it states that mobile devices identified in the section §2.1091(c) that operate at frequencies above 1.5 GHz with an ERP of 3 watts or more are required to perform routine environmental evaluation for RF exposure prior to equipment authorization or use; otherwise, they are categorically excluded. Therefore, as we can see this resulted ERP is below 3W, the routine environmental evaluation for RF exposure prior to equipment a uthorization or use for Tagg FTD tracking device in PCS band is categorically excluded. Conclusion The Tagg FTD tracking device meets the mobile 20 cm separation distance as specified in Section 2.1091 of the FCC rules. An appropriate RF exposure compliance statement will be placed in the User’s Guide.

FCC ID: J9CFTD1 Introduction and Purpose QUALCOMM Proprietary 1 Tagg FTD Conducted Test Report FCC Part 22 & 24 Certification FCC ID: J9CFTD1 Model: Tagg FTD 7403EBDA STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Test performed by: QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714 Report Prepared by: QUALCOMM Incorporated 5775 Morehouse Drive San Diego, CA 92121-1714 Approved by: Robert Scodellaro, Senior Staff Engineer Tests that required an OATS site were performed UL/CCS. FCC ID: J9CFTD1 Introduction and Purpose QUALCOMM Proprietary 2 Table of Contents 1. INTRODUCTION AND PURPOSE ............................................................................................................................................. 3 2. DESCRIPTION OF DEVICE UNDER TEST.............................................................................................................................. 3 3. TEST SUMMARY.......................................................................................................................................................................... 3 4. RF POWER OUTPUT VERIFICATION..................................................................................................................................... 3 4.1 BASE STATION EMULATOR SETTINGS AND MEASUREMENT PROCEDURES..................................................................................... 4 4.1.1 For CDMA2000 1x ............................................................................................................................................................. 4 4.2 TEST RESULTS............................................................................................................................................................................. 6 5. OCCUPIED BANDWIDTH........................................................................................................................................................... 7 5.1 TEST PROCEDURES...................................................................................................................................................................... 7 5.2 TEST RESULTS............................................................................................................................................................................. 8 5.3 PLOTS.......................................................................................................................................................................................... 9 6. BLOCK EDGE COMPLIANCE................................................................................................................................................. 11 6.1 TEST PROCEDURES.................................................................................................................................................................... 11 6.2 TEST RESULTS........................................................................................................................................................................... 12 6.3 PLOTS........................................................................................................................................................................................ 13 7. OUT OF BAND EMISSION AT ANTENNA TERMINALS .................................................................................................... 14 7.1 TEST PROCEDURE...................................................................................................................................................................... 14 7.2 TEST RESULT............................................................................................................................................................................. 15 7.3 PLOTS........................................................................................................................................................................................ 16 8. FREQUENCY STABILITY ........................................................................................................................................................ 20 8.1 TEST PROCEDURE...................................................................................................................................................................... 20 8.2 TEST RESULTS........................................................................................................................................................................... 21 9. TEST EQUIPMENT AND FIRMWARE ................................................................................................................................... 25 FCC ID: J9CFTD1 Introduction and Purpose QUALCOMM Proprietary 3 1. Introduction and Purpose This document provides the FCC test data for the Qualcomm Tagg FTD animal tracking device. The tests included in this report are limited to all conducted tests required. The radiated tests were performed at UL/CCS in Fremont, CA. and are reported in a separate document. 2. Description of Device Under Test Tagg FTD – The Pet Tracker uses advanced GPS and cellular supported tracking technology, allowing people to see where their dog is. Or more importantly, where their dog isn’t. While the technology behind Tagg is complex, the idea is quite simple. If a dog isn’t where it’s suppose to be, the owner gets notified, quickly via an email or text message. So now you’ll always have the peace of mind of knowing where you dog is whenever, wherever. You can check on your pet in three convenient ways: „ Using the Web app at your computer, you can see all of the information about your pet, …

Text truncated - open the document above for the full version.

RADIATED SPURIOUS EMISSIONS PORTIONS OF FCC CFR47 PART 22 SUBPART H FCC CFR47 PART 24 SUBPART E CERTIFICATION TEST REPORT FOR DOG TRACKING COLLAR MODEL: Tagg FTD FCC ID: J9CFTD1 REPORT NUMBER: 11U13718-1 ISSUE DATE: MARCH 19, 2011 Prepared for QUALCOMM INCORPORATED 5775 MOREHOUSE DRIVE SAN DIEGO, CA 92121, U.S.A. Prepared by COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 11U13718-1 DATE: MARCH 19, 2011 EUT: DOG TRACKING COLLAR FCC ID: J9CFTD1 Page 2 of 18 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Revision History Rev. Issue Date Revisions Revised By --- 03/19/2011 Initial Issue T. Chan REPORT NO: 11U13718-1 DATE: MARCH 19, 2011 EUT: DOG TRACKING COLLAR FCC ID: J9CFTD1 Page 3 of 18 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................... 4 2. TEST METHODOLOGY ........................................................................................................ 5 3. FACILITIES AND ACCREDITATION.................................................................................... 5 4. CALIBRATION AND UNCERTAINTY .................................................................................. 5 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................... 5 4.2. SAMPLE CALCULATION.............................................................................................. 5 4.3. MEASUREMENT UNCERTAINTY................................................................................ 5 5. EQUIPMENT UNDER TEST ................................................................................................. 6 5.1. DESCRIPTION OF EUT................................................................................................ 6 5.2. MAXIMUM OUTPUT POWER....................................................................................... 6 5.3. SOFTWARE AND FIRMWARE..................................................................................... 6 5.4. WORST-CASE CONFIGURATION AND MODE .......................................................... 6 5.5. DESCRIPTION OF TEST SETUP................................................................................. 8 6. TEST AND MEASUREMENT EQUIPMENT ....................................................................... 10 7. LIMITS AND RESULTS ...................................................................................................... 11 7.1. RADIATED OUTPUT POWER.................................................................................... 11 7.2. FIELD STRENGTH OF SPURIOUS RADIATION ....................................................... 14 8. SETUP PHOTOS................................................................................................................. 17 REPORT NO: 11U13718-1 DATE: MARCH 19, 2011 EUT: DOG TRACKING COLLAR FCC ID: J9CFTD1 Page 4 of 18 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: QUALCOMM INCORPORATED 5775 MOREHOUSE DRIVE SAN DIEGO, CA 92121, U.S.A. EUT DESCRIPTION: DOG TRACKING COLLAR MODEL: Tagg FTD SERIAL NUMBER: N10FDX92G DATE TESTED: MARCH 16-18, 2011 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 22H & 24E PASS (Radiated Portion) Compliance Certification Services, Inc. (UL CCS) tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL CCS based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL CCS and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL CCS will constitute fraud and shall nullify the document. No part of this report may be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any government agency. Approved & Released For UL CCS By: Tested By: THU CHAN CHIN PANG ENGINEERING MANAGER EMC ENGINEER UL CCS UL CCS REPORT NO: 11U13718-1 DATE: MARCH 19, 2011 EUT: DOG TRACKING COLLAR FCC ID: J9CFTD1 Page 5 of 18 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with TIA-603-C, FCC CFR 47 Part 2, FCC CFR 47 Part 22, and FCC CFR Part 24. 3. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 47173 Benicia Street, Fremont, California, USA. UL CCS is accredited by NVLAP, Laboratory Code 200065-0. The full scope of accreditation can be viewed at http://www.ccsemc.com . 4. CALIBRATION AND UNCERTAINTY 4.1. MEASURING INSTRUMENT CALIBRATION The…

Text truncated - open the document above for the full version.