J9CGSCK1Globalstar Mobile Car Kit for Portable User Terminal

QUALCOMM Globalstar GCK-1400 Hands-Free Car Kit Installation/User Guide 80-98438_book.book Page 1 Thursday, July 8, 1999 4:08 PM This guide is based on the production version of the QUALCOMM Globalstar GCK-1400 Hands-Free Car Kit. Software changes may have occurred after this printing. QUALCOMM reserves the right to make changes in technical and product specifications without prior notice. QUALCOMM Incorporated 5775 Morehouse Drive, San Diego, CA 92121-1710 Document Number 80-98438-1EN Rev- Model Number CXCKT051-1 Copyright 1999 QUALCOMM ® Incorporated. All rights reserved. QUALCOMM ® is a registered trademark of QUALCOMM Incorporated. Digital by QUALCOMM ® is a registered trademark of QUALCOMM Incorporated. SMART KEY™ is a trademark of QUALCOMM Incorporated. Globalstar™ is a trademark of Loral Qualcomm Satellite Services, Inc. Printed in the United States of America 80-98438_book.book Page 2 Thursday, July 8, 1999 4:08 PM iii Contents Introduction ...............................................................................................1 Features .................................................................................................1 Safety precautions .................................................................................1 Exposure to radio frequency signals .....................................................1 Antenna care ..........................................................................................2 Phone operation .....................................................................................2 Driving ...................................................................................................2 Electronic devices ..................................................................................3 Pacemakers .....................................................................................3 Hearing aids ...................................................................................3 Other medical devices ....................................................................3 Vehicles ...........................................................................................3 Posted facilities ...............................................................................3 Blasting areas ........................................................................................4 Potentially explosive atmospheres .......................................................4 For vehicles equipped with an air bag ..................................................4 Operation ....................................................................................................5 Using the phone in a vehicle .................................................................5 Attaching the phone to the Hands-Free Car Kit cradle ...............5 Turning on the phone and Hands-Free Car Kit ...........................6 Car stereo mute ..............................................................................6 Hands-free mode ....................................................................................7 When you use hands-free mode .....................................................7 Adjusting speaker volume .....................................................................7 Connecting to a personal computer or fax (optional) ...........................7 Privacy Handset (optional) ....................................................................8 Privacy handset operation .............................................................8 Privacy Headset .....................................................................................9 Privacy headset operation ..............................................................9 Installation ................................................................................................11 Unpacking the Hands-Free Car Kit ...................................................11 Hands-Free Car Kit standard components .................................11 Hands-Free Car Kit optional accessories ....................................12 Component parts .................................................................................13 Globalstar electronic module .......................................................13 Hands-Free Car Kit cradle ...........................................................13 Hands-Free speaker .....................................................................13 Hands-Free microphone ...............................................................13 Car interface cable ........................................................................13 Car stereo muting (STEREO MUTE) ..........................................14 Ignition sense ................................................................................14 Outdoor unit .................................................................................14 Optional accessories ............................................................................14 ODU cable .....................................................................................14 Privacy handset ............................................................................14 Privacy headset and adapter .......................................................15 80-98438_book.book Page iii Thursday, July 8, 1999 4:08 PM Contents iv Cellular antenna (not included) ...................................................16 Data cable (not included) .............................................................16 Precautions for installation .................................................................16 Where to install ...................................................................................16 Suggested positioning of components ..........................................17 Hands-Free Car Kit ......................................................................18 Installing the Hands-Free microphone .............................................…

Text truncated - open the document above for the full version.

QUALCOMM Proprietary: Restricted Distribution (This document contains critical information about QUALCOMM products and may not be distributed to anyone that is not an employee of Qualcomm without the approval of Configuration Management) Globalstar Portable User Terminal Car Kit FCC Part 25 Certification Report FCC ID: J9CGSCK1 80-98832-1 X1 Applicant: QUALCOMMFCC ID: J9CGSCK1 2 QUALCOMM Incorporated 6455 Lusk Blvd. San Diego, CA, 92121-2779 U.S.A. Copyright © QUALCOMM, Incorporated, 1999. All rights reserved. Printed in the United States of America. All data and information contained in or disclosed by this document are confidential and proprietary information of QUALCOMM Incorporated and all rights therein are expressly reserved. By accepting this material the recipient agrees that this material and the information contained therein are held in confidence and in trust and will not be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of QUALCOMM Incorporated. This technology is controlled by the United States Government. Diversion contrary to U.S. law prohibited. QUALCOMM Proprietary: : Restricted Distribution (This document contains critical information about QUALCOMM products and may not be distributed to anyone that is not an employee of Qualcomm without the approval of Configuration Management) Globalstar™ is a trademark of Loral Qualcomm Satellite Services, Inc. Globalstar Portable User Terminal Car Kit FCC Part 25 Certification Report FCC ID: J9CGSCK1 80-98832-1 X1 July 16, 1999 Applicant: QUALCOMMFCC ID: J9CGSCK1 3 MANUFACTURER Qualcomm Incorporated 6455 Lusk Boulevard, San Diego, CA 92121-2779 Tel: 619-587-1121 Copyright © 1998 QUALCOMM Incorporated. All rights reserved Printed in the United States of America REGULATORY ENGINEERING MANAGER Jay Moulton Director of Engineering, Regulatory Location: Qualcomm Building V, Office V-265I Tel: 619-658-3428 Fax: 619-651-xxxx e-mail: [email protected] REGULATORY ENGINEERING SPECIALIST Paul Guckian Staff/Manager EMC & Regulatory: Gateway Project Location: Qualcomm Inc. Building R office R-202L. Tel: 619-651-1547 Fax: 619-651-1988 e-mail: [email protected] Applicant: QUALCOMMFCC ID: J9CGSCK1 4 Document Amendment Record DATEDETAILS OF CHANGE (affected pages, etc.) ISSUE STATUS MANUFACTURER APPROVAL 7/15/99Initial Document Release1William Moyer Applicant: QUALCOMMFCC ID: J9CGSCK1 5 July 7, 1999 Federal Communications Commission Office of engineering and Technology Re: Application for Certification of Globalstar Portable User Terminal Car Kit, FCC ID No. J9CGSCK1 Gentlepeople: Enclosed please find the following documentation for your review: 1. FCC Form 731, including the fee processing form, for the Globalstar Gateway RF Subsystem. 2. A letter for Request for confidentiality. 3. Notification of separate fee payment submittal in the form of a check ($610.00) #19xxxx and accompanying executed Form 159. 4.All test data and support documentation as required for certification under Part 2 and Part 25 of Title 47 of the Code of Federal Regulations Ch. 1 (10-1-98 Edition). If any further information is required please contact myself or Paul Guckian. You may contact me directly by phone at 619-658-3542, by fax at 619-651- 1982, or by e-mail at [email protected]. You may contact Paul Guckian directly by phone at 619-651-1547, by fax at 619-651-1988, or by e- mail at [email protected]. Please inform us when the Request for Confidentiality has been accepted and also when certification has been granted. Very truly yours, William E. Moyer Sr. Engineer, EMC & Regulatory Applicant: QUALCOMMFCC ID: J9CGSCK1 6 FCC Form 731 for Portable User Terminal Car Kit Applicant: QUALCOMMFCC ID: J9CGSCK1 7 FCC Form 731 for Portable User Terminal Portable User Terminal Car Kit (p. 2) Applicant: QUALCOMMFCC ID: J9CGSCK1 8 FCC Form 731 for Portable User Terminal Car Kit (p. 3) Applicant: QUALCOMMFCC ID: J9CGSCK1 9 Federal Communications Commission Reference: FCC ID: J9CGSCK1 Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission’s rules, Qualcomm Incorporated hereby requests confidentiality for certain aspects of the information accompanying this Application for Certification as specifically identified below: 1Exhibit 3, Globalstar Compliance Lab Reverse Link Test Procedure (File: E.3 80-98735-1_x1.pdf) 2.Exhibit 4, Globalstar Compliance Lab Out-of-Band and In-Band Noise and Spurious Emissions Test Data (Files: E.4a CK obn&s data.pdf, E.4b CK ibn&s data.pdf, and E.4c GS Ant Gain.pdf ) 3.Exhibit 5, Globalstar CK EMC Test Plan (File: E.5 GS CK EMC TP.pdf) 4.Exhibit 6, Globalstar CK EMC Test Report (Files: E.6 CK c photo-001 ext.pdf, E.6 EMC Lab c photo-002.pdf, ... E.6 EMC Lab c photo-010.pdf and E.6. TUV CK EMC TR.pdf) 5.Exhibit 7, CAR KIT Maximum Permissible Exposure Analysis (File: E.7 CK MPE Analysis.pdf) 6. Exhibit 8, Frequency Stability Data (File: E.8 CK Freq. Stability.pdf) 7. Exhibit 10, Description of the Globalstar System (File: E.10 Description of GS.pdf) 8. Exhibit 12, GS Car Kit Outdoor Unit Drawings (Files: E.12a 20-81130_X8.pdf, E.12b LD20-81130_X8.pdf, E.12c PL20-81130-1X14.pdf, E.12d CK RF TX Block.pdf, and E.12e CK ODU Cover.pdf) 9. Exhibit 13, GS Car Kit Electronic Module (GEM) Drawings (Files: E.13a 20-81527_X2.pdf, E.13b LD20-81527_X2.pdf, E.13c PL20-81527-1x7.pdf, and E.13d 10-81100_X2.pdf) 10. Exhibit 14, GS Car Kit Cradle Drawings (Files: E.14a 20-81525_X3.pdf, E.14b LD20-81525_X3.pdf, and E.14c PL20-81525-1X3.pdf) 11. Exhibit 15, Portable Antenna Assembly Drawings (Files: E.15a CV90-70766_X7.pdf and E.15b 80-70813-1_X4.pdf) 12. Exhibit 16, Car Kit Accessories Drawings (Files: E.16a CV90-81218_X1.pdf, E.16b CV90-46361_B.pdf, E.16c CV90-46349.pdf, E.16d PL65-66369-1X1.pdf, and E.16e CK Access Dwgs.pdf) Applicant: QUALCOMMFCC ID: J9CGSCK1 10 All items contain trade secrets and other proprietary information not customarily releas…

Text truncated - open the document above for the full version.

1Frank Coperich,9/2/99 10:43 AM -0700,Confidentiality Revisions for Remaining To: "Frank Coperich" <[email protected]> From: Bill Moyer x8-3542 <[email protected]> Subject: Confidentiality Revisions for Remaining Globalstar UT Filings Cc: pguckian, jmoulton, kstambau Bcc: X-Attachments: Frank Coperich: This e-mail will be printed to disk using PDFWriter and submitted as an attachment pdf file to each of the remaining Globalstar UT filings via the filing submissions Webpage. It is also being sent to you directly, because lacking an open correspondence Reference Number for each filing, it is not possible to submit correspondence to those filings. And also so that we will have a record of what was submitted. ----- Per your below appended request and pursuant to the DFUT filing correspondence, here are the revisions to our confidentiality requests (identified by confidentiality request letter item number) for the remaining Globalstar UT filings: We withdraw our request for confidentiality of items 1 through 7 of our SMP UT confidentiality request letter (FCC ID: J9CGSSM1, EA94445). We withdraw our request for confidentiality of items 1 through 10 of our TMP UT confidentiality request letter (FCC ID: J9CGSTM1, EA94735). We withdraw our request for confidentiality of items 1 through 8 of our AFUT confidentiality request letter (FCC ID: J9CGSAF1, EA94736). We withdraw our request for confidentiality of items 1 through 7 of our Car Kit confidentiality request letter (FCC ID: J9CGSCK1, EA94778). -WEM >Date: Thu, 02 Sep 1999 11:13:17 -0400 >From: "Frank Coperich" <[email protected]> >To: wmoyer >Subject: Ref. No. 9479: Requested Information for FCC ID: >J9CGSDF1,EA94247 Filing -Reply >Mime-Version: 1.0 > >Application for EAS 94247 is Granted. > >Ref - Confidentiality - please send any revisions for EAS 94445, 94735, 94736 and 94778 directly that those filings. > > >>>> Bill Moyer x8-3542 <[email protected]> 09/01/99 09:33pm >>> > 1Printed for Bill Moyer x8-3542 <[email protected]>

[email protected],9/17/99 2:05 PM -0700,Requested Information FCC ID J9CG To: [email protected] From: Bill Moyer x8-3542 <[email protected]> Subject: Requested Information FCC ID J9CGSCK1, EA94778 Filing Cc: pguckian, jmoulton, kstambau, mcarosel Bcc: X-Attachments: Frank Coperich: This e-mail will be printed to disk using PDFWriter and submitted as an attachment pdf file via the filing submissions webpage. It is also being sent to you directly in parallel so that we will have a record of what was submitted. My responses to your specific questions and comments are interleaved below in blue italics, so that they may be more readily discerned. >Date: Fri, 17 Sep 1999 08:40:22 -0400 >From: [email protected] (OET) >To: wmoyer >Subject: > >To:William Moyer, Qualcomm Incorporated >From:Frank Coperich >[email protected] >FCC Application Processing Branch > >Re:FCC ID J9CGSCK1 >Applicant:Qualcomm Incorporated >Correspondence Reference Number:9660 >731 Confirmation Number:EA94778 >Date of Original E-Mail:09/17/1999 > > >1.) There is no supporting information for the proposed 35 cm separation distance indicated in the installation note included in this filing for this car kit. This note also needs to be revised to indicate that this is an installation requirement, since listing all the regulations and the separation distance without explaining what the exact installation requirement is to fulfill regulations is insufficient. Justification for the 35 cm separation distance constraint was provided in the Car Kit MPE Analysis, submitted as file E.7 Car Kit MPE Analysis.pdf, with File Description label: E 7 CK MPE Analysis, Exhibit Type declaration: Schematics (which was an error, it was intended to be submitted as RF Exposure Info). The errata sheet for the Car Kit Installation/User Guide did not explicitly state that adherence to the 35 cm separation distance was an installation requirement. However the last paragraph of the section on Exposure to Radio Frequency Signals in that errata sheet (repeated below) did state the reasoning behind the restriction: "The phone and this Car kit are designed to comply with established ANSI, FCC, and international safety standards for safe levels of human exposure to RF energy. Nonetheless, RF field intensity at the surface of the transmitting car kit antenna is fairly high. Maintaining a minimum line-of-sight separation distance of 35 cm (14 inches) between the transmitting antenna and all personnel will ensure that the General Population / Uncontrolled Exposure maximum permissible exposure (MPE) limits are not exceeded. This satisfies the MPE limits mandated by the FCC in 47 CFR Ch. 1 (10-1-98 Edition), Part 1, §1.1310 and defined in the ANSI/IEEE C95.1-1992 standard, and also satisfies the slightly more-stringent European and international exposure limit recommendations of IRPA (1991) and ICNIRP (1996)." 1Printed for Bill Moyer x8-3542 <[email protected]> [email protected],9/17/99 2:05 PM -0700,Requested Information FCC ID J9CG Per your request the draft errata sheet has been revised to add the following statement to the section on Mounting the ODU: "Caution As discussed in the earlier section on exposure to radio frequency signals, when the ODU is transmitting it is necessary that at least a 35 cm (14 inch) line-of-sight separation distance be maintained between the ODU antenna and the people within or near the vehicle. Mounting the ODU at least 35 cm from the edge of the vehicle roof will satisfy that requirement under normal use conditions." A copy of the revised draft errata sheet has been uploaded to the electronic filing Webpage as file: E.11b CK MPE Restrict.pdf, with File Description label: E 11b CK MPE Restrict and Exhibit Type declaration: Users Manual. > >2.) The final output of the ODU/antenna will be dependent on the input device or phone. Please indicate what phones are this car kit for or what input restrictions are there to ensure the output for this car kit will be within the limits of those proposed. The Car Kit supports operation with the Tri-Mode UT (TMP UT, FCC ID: J9CGSTM1, EA94735) and the Single-Mode UT (SMP UT, FCC ID: J9CGSSM1, EA94445). > >3.) For the cellular antenna option provided by this car kit, categorical exclusion from MPE evaluation is dependent on the antenna gain and output of the individual phone. Please clarify the type of antennas to be used that are appropriate for categorical exclusion from routine MPE evaluation or otherwise MPE evaluation is needed. For mobile operations, a minimum of 20 cm separation or more is needed which should be included as part of the installation instructions to ensure compliance. The Car Kit provides a coaxial interface cable to connect to a 3rd party coax cable and externally-mounted cellular antenna. The resultant radiated terrestrial-mode transmit power is not known, but will be less than 1.5 W ERP at a distance greater than 20 cm from the body, meeting the MPE low-power categorical exclusion criterion of §2.1091 (c). That conclusion is supported by consideration of the worst-case maximum ERP output of the phone with its built-in 4.1 dBi whip antenna (30 dBm, including 2 dB error tolerance), the maximum credible additional gain which could be provided by a 3rd party cellular antenna, 1.1 dB (5.2 dB - 4.1 dB) for a quarter-wave monopole with a large ground plane, and the probable cable loss for the greater length of coaxial cable between the phone PA and the antenna (0.5 to 1.0 dB). Together that yields a worst-case maximum predicted transmit power of 30.1 to 30.6 dBm ERP, 1.02 to 1.15 W ERP. Other forms of omnidirectional antenna suitable for cellular transmissions, including a short dipole, half-wave dipole, monopole on a small ground planes, and a small loop antenna, will have a lower gain than that of a quarter wave monopole over a large ground plane, and hence a lower ERP value. Directional narrowbeam antennas would have substantially higher antenna gains and ERP within thei…

Text truncated - open the document above for the full version.

E.9a CK ODU Label pict

E.9b CK GEM Label pict

CK Cradle Label pict

QUALCOMM Proprietary: Restricted Distribution (This document contains critical information about QUALCOMM products and may not be distributed to anyone that is not an employee of Qualcomm without the approval of Configuration Management) Globalstar Portable User Terminal Car Kit FCC Part 25 Certification Report FCC ID: J9CGSCK1 80-98832-1 X1 Applicant: QUALCOMMFCC ID: J9CGSCK1 2 QUALCOMM Incorporated 6455 Lusk Blvd. San Diego, CA, 92121-2779 U.S.A. Copyright © QUALCOMM, Incorporated, 1999. All rights reserved. Printed in the United States of America. All data and information contained in or disclosed by this document are confidential and proprietary information of QUALCOMM Incorporated and all rights therein are expressly reserved. By accepting this material the recipient agrees that this material and the information contained therein are held in confidence and in trust and will not be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of QUALCOMM Incorporated. This technology is controlled by the United States Government. Diversion contrary to U.S. law prohibited. QUALCOMM Proprietary: : Restricted Distribution (This document contains critical information about QUALCOMM products and may not be distributed to anyone that is not an employee of Qualcomm without the approval of Configuration Management) Globalstar™ is a trademark of Loral Qualcomm Satellite Services, Inc. Globalstar Portable User Terminal Car Kit FCC Part 25 Certification Report FCC ID: J9CGSCK1 80-98832-1 X1 July 16, 1999 Applicant: QUALCOMMFCC ID: J9CGSCK1 3 MANUFACTURER Qualcomm Incorporated 6455 Lusk Boulevard, San Diego, CA 92121-2779 Tel: 619-587-1121 Copyright © 1998 QUALCOMM Incorporated. All rights reserved Printed in the United States of America REGULATORY ENGINEERING MANAGER Jay Moulton Director of Engineering, Regulatory Location: Qualcomm Building V, Office V-265I Tel: 619-658-3428 Fax: 619-651-xxxx e-mail: [email protected] REGULATORY ENGINEERING SPECIALIST Paul Guckian Staff/Manager EMC & Regulatory: Gateway Project Location: Qualcomm Inc. Building R office R-202L. Tel: 619-651-1547 Fax: 619-651-1988 e-mail: [email protected] Applicant: QUALCOMMFCC ID: J9CGSCK1 4 Document Amendment Record DATEDETAILS OF CHANGE (affected pages, etc.) ISSUE STATUS MANUFACTURER APPROVAL 7/15/99Initial Document Release1William Moyer Applicant: QUALCOMMFCC ID: J9CGSCK1 5 July 7, 1999 Federal Communications Commission Office of engineering and Technology Re: Application for Certification of Globalstar Portable User Terminal Car Kit, FCC ID No. J9CGSCK1 Gentlepeople: Enclosed please find the following documentation for your review: 1. FCC Form 731, including the fee processing form, for the Globalstar Gateway RF Subsystem. 2. A letter for Request for confidentiality. 3. Notification of separate fee payment submittal in the form of a check ($610.00) #19xxxx and accompanying executed Form 159. 4.All test data and support documentation as required for certification under Part 2 and Part 25 of Title 47 of the Code of Federal Regulations Ch. 1 (10-1-98 Edition). If any further information is required please contact myself or Paul Guckian. You may contact me directly by phone at 619-658-3542, by fax at 619-651- 1982, or by e-mail at [email protected]. You may contact Paul Guckian directly by phone at 619-651-1547, by fax at 619-651-1988, or by e- mail at [email protected]. Please inform us when the Request for Confidentiality has been accepted and also when certification has been granted. Very truly yours, William E. Moyer Sr. Engineer, EMC & Regulatory Applicant: QUALCOMMFCC ID: J9CGSCK1 6 FCC Form 731 for Portable User Terminal Car Kit Applicant: QUALCOMMFCC ID: J9CGSCK1 7 FCC Form 731 for Portable User Terminal Portable User Terminal Car Kit (p. 2) Applicant: QUALCOMMFCC ID: J9CGSCK1 8 FCC Form 731 for Portable User Terminal Car Kit (p. 3) Applicant: QUALCOMMFCC ID: J9CGSCK1 9 Federal Communications Commission Reference: FCC ID: J9CGSCK1 Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission’s rules, Qualcomm Incorporated hereby requests confidentiality for certain aspects of the information accompanying this Application for Certification as specifically identified below: 1Exhibit 3, Globalstar Compliance Lab Reverse Link Test Procedure (File: E.3 80-98735-1_x1.pdf) 2.Exhibit 4, Globalstar Compliance Lab Out-of-Band and In-Band Noise and Spurious Emissions Test Data (Files: E.4a CK obn&s data.pdf, E.4b CK ibn&s data.pdf, and E.4c GS Ant Gain.pdf ) 3.Exhibit 5, Globalstar CK EMC Test Plan (File: E.5 GS CK EMC TP.pdf) 4.Exhibit 6, Globalstar CK EMC Test Report (Files: E.6 CK c photo-001 ext.pdf, E.6 EMC Lab c photo-002.pdf, ... E.6 EMC Lab c photo-010.pdf and E.6. TUV CK EMC TR.pdf) 5.Exhibit 7, CAR KIT Maximum Permissible Exposure Analysis (File: E.7 CK MPE Analysis.pdf) 6. Exhibit 8, Frequency Stability Data (File: E.8 CK Freq. Stability.pdf) 7. Exhibit 10, Description of the Globalstar System (File: E.10 Description of GS.pdf) 8. Exhibit 12, GS Car Kit Outdoor Unit Drawings (Files: E.12a 20-81130_X8.pdf, E.12b LD20-81130_X8.pdf, E.12c PL20-81130-1X14.pdf, E.12d CK RF TX Block.pdf, and E.12e CK ODU Cover.pdf) 9. Exhibit 13, GS Car Kit Electronic Module (GEM) Drawings (Files: E.13a 20-81527_X2.pdf, E.13b LD20-81527_X2.pdf, E.13c PL20-81527-1x7.pdf, and E.13d 10-81100_X2.pdf) 10. Exhibit 14, GS Car Kit Cradle Drawings (Files: E.14a 20-81525_X3.pdf, E.14b LD20-81525_X3.pdf, and E.14c PL20-81525-1X3.pdf) 11. Exhibit 15, Portable Antenna Assembly Drawings (Files: E.15a CV90-70766_X7.pdf and E.15b 80-70813-1_X4.pdf) 12. Exhibit 16, Car Kit Accessories Drawings (Files: E.16a CV90-81218_X1.pdf, E.16b CV90-46361_B.pdf, E.16c CV90-46349.pdf, E.16d PL65-66369-1X1.pdf, and E.16e CK Access Dwgs.pdf) Applicant: QUALCOMMFCC ID: J9CGSCK1 10 All items contain trade secrets and other proprietary information not customarily releas…

Text truncated - open the document above for the full version.

Car Kit Instalation/User Guide (80-98438-1 EN Rev-) Errata Sheet Input Modifications to Add MPE Distance Restriction Statement to Introduction: Exposure to radio frequency signals: Add to bulletized list following 2 nd paragraph in section (references are to be added to list of footnotes at bottom of page): •ANSI/IEEE C95.1-1992 Standard, American Natonal Standards Institute (Delete ANSI C95.1 (1992) from list.) •IRPA (1991) Guidelines on Protection Against Non-Ionizing Radiation, International Radiation Protection Association Replace last paragraph of section with the following: The phone and this Car kit are designed to comply with established ANSI, FCC, and international safety standards for safe levels of human exposure to RF energy. Nonetheless, RF field intensity at the surface of the transmitting car kit antenna is fairly high. Maintaining a minimum line-of-sight separation distance of 35 cm (14 inches) between the transmitting antenna and all personnel will ensure that the General Population / Uncontrolled Exposure maximum permissible exposure (MPE) limits are not exceeded. This satisfies the MPE limits mandated by the FCC in 47 CFR Ch. 1 (10-1-98 Edition), Part 1, §1.1310 and defined in the ANSI/IEEE C95.1-1992 standard, and also satisfies the slightly more-stringent European and international exposure limit recommendations of IRPA (1991) and ICNIRP (1996).

Car Kit Instalation/User Guide (80-98438-1 EN Rev-) Errata Sheet Input Modifications to Add MPE Distance Restriction Statement to Introduction: Exposure to radio frequency signals: Add to bulletized list following 2 nd paragraph in section (references are to be added to list of footnotes at bottom of page): •ANSI/IEEE C95.1-1992 Standard, American Natonal Standards Institute (Delete ANSI C95.1 (1992) from list.) •IRPA (1991) Guidelines on Protection Against Non-Ionizing Radiation, International Radiation Protection Association Replace last paragraph of section with the following: The phone and this Car kit are designed to comply with established ANSI, FCC, and international safety standards for safe levels of human exposure to RF energy. Nonetheless, RF field intensity at the surface of the transmitting car kit antenna is fairly high. Maintaining a minimum line-of-sight separation distance of 35 cm (14 inches) between the transmitting antenna and all personnel will ensure that the General Population / Uncontrolled Exposure maximum permissible exposure (MPE) limits are not exceeded. This satisfies the MPE limits mandated by the FCC in 47 CFR Ch. 1 (10-1-98 Edition), Part 1, §1.1310 and defined in the ANSI/IEEE C95.1-1992 standard, and also satisfies the slightly more-stringent European and international exposure limit recommendations of IRPA (1991) and ICNIRP (1996). Modifications to Add MPE Separation Distance Requirement to instructions on Mounting the ODU: Add following Caution Warning: Caution As discussed in the earlier section on exposure to radio frequency signals, when the ODU is transmitting, it is necessary that at least a 35 cm (14 inch) line-of- sight separation distance be maintained between the ODU antenna and the people within or near the vehicle. Mounting the ODU at least 35 cm from the edge of the vehicle roof will satisfy that requirement under normal use conditions.

3-3-99 GS UT NB OOBE Test Plan 1 of 7 Globalstar User Terminal Transmitter Antenna Port Conducted Narrowband Out-of-Band Emissions (OOBE) Test Plan 1.0Introduction This test plan describes the planned narrowband unwanted out-of-band emissions testing of the Globalstar user terminal (UT) transmitter antenna ports. This testing will support verification that the UT meets the FCC emissions limitation requirements specified in 47 CFR Ch. 1 (10-1-97 Edition), Part 25, Sections 25.213 (b), and (per Report and Order FCC 98-338, adopted Dec. 17, 1998), Section 25.200 (c), and to provide data required for the UT Certificatio…

Text truncated - open the document above for the full version.