J9CGSTM1Globalstar Tri-Mode Portable User Terminal

QUALCOMM Globalstar GSP-1600 Tri-Mode Phone User Guide Clr Info Send End 1 2 3 abc def 4 5 6 jkl ghi mno 7 8 9 tuv prs wxyz * # 0 + pwr This guide is based on the production version of the QUALCOMM Globalstar GSP-1600 Tri-Mode Phone. Software changes may have occurred after this printing. QUALCOMM reserves the right to make changes in technical and product specifications without prior notice. QUALCOMM Incorporated 5775 Morehouse Drive, San Diego, CA 92121-1714 Document Number 80-98153-1EN Rev. A Model Number CKABP0001 Copyright 1999 QUALCOMM® Incorporated All rights reserved This technology was exported from the United States in accordance with Export Administration Regulations. Diversion contrary to U.S. law prohibited. QUALCOMM® is a registered trademark of QUALCOMM Incorporated. Digital by QUALCOMM® is a registered trademark of QUALCOMM Incorporated. SMART KEY™ is a trademark of QUALCOMM Incorporated. Globalstar™ is a trademark of Loral Qualcomm Satellite Services, Inc. Printed in the United States of America iii Cautions and Warnings Warning Only use the batteries, antennas, and chargers provided by QUALCOMM. The use of any other type may be dangerous. Warning Allow only authorized personnel to service the phone and its accessories. Unauthorized service can invalidate the warranty. Caution Any changes or modifications to this equipment not expressly approved in this document could void your warranty and your authority to operate this equipment. Caution Avoid exposing the phone and accessories to rain or other liquids. If the phone gets wet, turn the power off immediately and remove the battery pack. See Battery Care and Maintenance, page 53, for more information. Note When using the QUALCOMM Globalstar Tri-Mode Phone near a television or radio, the phone can cause interference. Regulatory agencies in your area, such as the United States Federal Communications Commission (FCC) or Canadian Industry Canada (IC), can require you to stop using the phone if such interference cannot be eliminated. If you need assistance, contact your satellite or cellular service provider. iv v Contents Getting Started ..........................................................................................1 Understanding your phone ...................................................................1 Contacting customer service .................................................................1 Solving problems ....................................................................................1 Understanding this guide ......................................................................1 Preparing for satellite calls ...................................................................2 Making satellite calls ............................................................................3 Making cellular calls .............................................................................4 Answering calls ......................................................................................4 Ending calls ............................................................................................4 Displaying your phone number .............................................................4 Phone Basics ...............................................................................................5 Phone features and keypad .................................................................5 Display indicators ..................................................................................7 Security module .....................................................................................8 Antenna basics .......................................................................................8 Information key .....................................................................................8 Calling Basics .............................................................................................9 Turning the phone on ............................................................................9 Turning the phone off ............................................................................9 Standby mode .......................................................................................9 Power save mode .................................................................................10 Entering numbers ................................................................................10 Making emergency calls ......................................................................11 Redialing a call ....................................................................................11 Muting a call ........................................................................................11 Possible service provider services .......................................................11 Menu Basics ..............................................................................................13 Accessing main menu ..........................................................................14 Navigating and using menus ..............................................................14 Phone Book Menu ...................................................................................15 Entering letters and other characters ................................................15 Entering pauses ...................................................................................16 Saving entries ......................................................................................16 Finding entries .....................................................................................17 Editing entries .....................................................................................18 Erasing entries ....................................................................................18 Making entries secret ..........................................................................18 Viewing numbers ................................…

Text truncated - open the document above for the full version.

[email protected],8/24/99 3:29 PM -0700,Requested Information for FCC ID J9 To: [email protected] From: Bill Moyer x8-3542 <[email protected]> Subject: Requested Information for FCC ID J9CGSTM1, EA94735 Filing Cc: Bcc: X-Attachments: Frank Coperich: This e-mail will be printed to disk using PDFWriter and submitted as an attachment pdf file via the filing submissions webpage. It is also being sent to you directly in parallel so we will have a record of what was submitted, that being something the Webpage does not always provide due to time-out problems. My responses to your specific questions and comments are interleaved below in blue italics so they may be more readily discerned. >Date: Thu, 19 Aug 1999 15:37:39 -0400 >From: [email protected] (OET) >To: wmoyer >Subject: > >To:William Moyer, Qualcomm Incorporated >From:Frank Coperich >[email protected] >FCC Application Processing Branch > >Re:FCC ID J9CGSTM1 >Applicant:Qualcomm Incorporated >Correspondence Reference Number:9295 >731 Confirmation Number:EA94735 >Date of Original E-Mail:08/19/1999 > > > >1. Qualcomm is requesting 0.8 W for Part 25, probably ERP. It needs to be clarified if this is conducted, ERP or EIRP. SAR report has 28 dBm plus 3 dBi antenna gain = 31 dBm EIRP. Not sure what is reported in the EMC portion for Part 25. Other information in the filing is indicating 1.0 W EIRP with 0.4 W EIRP being typical (section 3.5 of description). The following table should clarify what the rated power levels are. While Globalstar GAI and Part 25 limits and power levels are generally defined as EIRP values, CDMA Cellular and AMPS mode values are generally defined as ERP values. For consistency in the Tri-Mode UT online Form 731, ERP values were used for all 3 modes. In Exhibit 1, Section 3.5, EIRP values are given for Globalstar mode transmissions, while ERP values are given for CDMA cellular and AMPS mode transmissions. Globalstar UT Emissions Designators and Data: Globalstar Transmissions: Ref. Des. 1M25G1W 1610-1621.35 MHz, 10 ppm freq. tolerance Rated RF Power: Portable UT's: 1.0 W, 0.0 dBW EIRP max. (0.4 W, -4.0 dBW EIRP typ.) 0.8 W, -1.1 dBW ERP max. (0.3 W, -5.9 dBW ERP typ.) 1Printed for Bill Moyer x8-3542 <[email protected]> [email protected],8/24/99 3:29 PM -0700,Requested Information for FCC ID J9 Mobile (Car Kit) and Fixed UT's 4.0 W, 6.0 dBW EIRP max. (2.0 W, 3.0 dBW EIRP typ.) 2.5 W, 3.9 dBW ERP max. (1.2 W, 0.9 dBW ERP typ.) CDMA Cellular Transmissions: Ref. Des. 1M25F9W 824.02-848.98 MHz, 10 ppm freq. tolerance Rated RF Power: 0.6 W, -2.2 dBW ERP max. FM AMPS Transmissions: Ref. Des. 40K0F8W 40K0F1D 824.02-848.98 MHz, 0.00025% freq. tolerance Rated RF Power: 0.6 W, -2.2 dBW ERP max. > >2. The device has two battery options, a standard and an extended battery. Which one of these batteries was used during the SAR test? Highest SAR for AMPS mode is 1.47 W/kg. Please clarify if the two battery options will result in SAR variations higher than those reported for the worst case in AMPS mode? While it was planned to offer two battery options, a standard battery and a more bulky extended battery, that has changed. Qualcomm will now offer only one battery, a new polymer battery with the same form factor as the old standard battery and greater energy storage capacity than the old extended battery. A copy of the revised User Guide, with language reflecting this change, will be uploaded as attachment file E.15a 80-98153-1EN Rev-A.PDF. The SAR performance has been verified in this configuration and accurately reflects the data contained in the TMP UT SAR Report, submitted as file E.13 TMP SAR TR.pdf. Note please that for conservatism the AMPS power level tested was deliberately greater than the worst case which will be encountered in the field, having been specially adjusted to provide a level somewhat above the maximum rated radiated power (0.6 W ERP, 28 dBW ERP) + 2 dB error tolerance. > >3. The users manual indicates there are optional accessories such as leather case, privacy headset, handset and adapter cable etc. Please clarify if these optional items will allow body-worn operations for this device. For example, does the leather case has a belt-clip that will allow body-worn operation through a headset and adapter cable for normal use; or are these items limited to other operating configurations. If body-worn conditions is allowed, worst case SAR needs to be addressed for the allowable operating modes. The privacy handset and headset are optional Car Kit accessories which cannot be plugged directly into the phone. No accessories support body worn operation. > >4. Please clarify if all three operating modes, Satellite, AMPS and CDMA always co-exist in all models of this phone. If not, please address if differences in hardware combinations will affect SAR, that is, SAR for phones without AMPS or CDMA sections etc. Qualcomm offers only two models of Globalstar Portable UT's: the Tri-Mode 2Printed for Bill Moyer x8-3542 <[email protected]> [email protected],8/24/99 3:29 PM -0700,Requested Information for FCC ID J9 phone (FCC ID: J9CGSTM1, filing EA94735) which supports all 3 modes of operation, and the Single-Mode phone (FCC ID: J9CGSSM1, filing EA94445) which operates only in Globalstar Mode. > >5. Please identify the locations of peak SAR for the Satellite mode, is it at the top of the head? The SAR contour plots appear to indicate higher SAR is possible along side wall sections of the phantom, please clarify. We do not expect SAR to exceed limit for the Satellite mode according to the test setup and operating configurations, but should revise procedures for future tests. FYI - DASY systems has new procedures for measuring SAR along side walls. Please also identify the locations of peak SAR with respect to the phone and phantom for the AMPS and CDMA modes, or re-submit the worst case AMPS mode SAR plot with an outline of the phone and phantom indicated/sketched on it. Peak Globalstar mode SAR is across the upper foreh…

Text truncated - open the document above for the full version.

[email protected],8/31/99 5:27 PM -0700,2nd Requested Information for FCC I To: [email protected] From: Bill Moyer x8-3542 <[email protected]> Subject: 2nd Requested Information for FCC ID J9CGSTM1, EA94735 Filing Cc: pguckian, kstambau, jmoulton Bcc: X-Attachments: Frank Coperich: This e-mail will be printed to disk using PDFWriter and submitted as an attachment pdf file via the filing submissions webpage. It is also being sent to you directly in parallel so we will have a record of what was submitted. My responses to your specific questions and comments are interleaved below in blue italics so they may be more readily discerned. -WEM >Date: Tue, 31 Aug 1999 18:33:35 -0400 >From: [email protected] (OET) >To: wmoyer >Subject: > >To:William Moyer, Qualcomm Incorporated >From:Frank Coperich >[email protected] >FCC Application Processing Branch > >Re:FCC ID J9CGSTM1 >Applicant:Qualcomm Incorporated >Correspondence Reference Number:9468 >731 Confirmation Number:EA94735 >Date of Original E-Mail:08/31/1999 > > > >1.) Qualcomm is requesting 0.8 W ERP for Satellite mode (1.32 W EIRP). SAR was performed at 31 dBm EIRP (about 1.26 W). Whatever output level determined by the EMC data and put on the grant should not exceed 1.26 W EIRP for Part 25. Apologies. There is an error in the table submitted in our initial response No. 1, and in the electronically submitted Form 731. The Globalstar mode power should be 0.62 W (-2.1 dBW) ERP, 1.0 W (0.0 dBW) EIRP. The EIRP values for Globalstar satellite mode are the basis values; the derived Globalstar satellite mode ERP values (one of which was used in form 731) were miscalculated. For reference the portable UT power in the previous Response No. 1 Globalstar UT Emissions Designators and Data table should have read as follows: Portable UT's: 1.0 W, 0.0 dBW EIRP max. (0.4 W, -4.0 dBW EIRP typ.) 0.62 W, -2.1 dBW ERP max. (0.25 W, -6.1 dBW ERP typ.) The Form 731 Globalstar satellite mode transmit power input and the Grant should be corrected to read either 1.0 W EIRP or equivalently 0.62 W ERP, depending on whether we need the units for the Part 22 and Part 25 emissions to be different or the same. > >2.) Response #1 indicates 4.0 W EIRP output for a car-kit operating in the satellite mode. This rating exceeds the requested 0.8 W ERP (1.32 W EIRP) output level for Part 25. It also conflicts with information provided in response #6, which describes the car-kit is for cellular mode operation only. Please clarify if car-kit is 1Printed for Bill Moyer x8-3542 <[email protected]> [email protected],8/31/99 5:27 PM -0700,2nd Requested Information for FCC I applicable for Part 25 and address MPE accordingly if necessary (may also need to do something to the ouptut to be put on the grant) > There seems to be some confusion here. The Car kit provides two separate transmit functions for the UT. In satellite mode the Car Kit takes the RF signal from the phone, amplifies it, and transmits the signal from the antenna built into the vehicle-mounted Car Kit ODU. Those transmissions and that mode of combined UT and Car Kit operation at 4.0 W EIRP output are the subject of the Globalstar Car Kit filing (FCC ID: J9CGSCK1, EA94778). The Car Kit MPE analysis was submitted as attachment E.7 Car Kit MPE Analysis.pdf. In terrestrial cellular mode, the Car Kit provides only a passive pass-through coaxial connectivity to a 3rd party vehicle-mounted cellular antenna, as discussed in our initial response No. 6. > >The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 60 days of the original e-mail date may result in application dismissal pursuant to Section 2.917 (c) and forfeiture of the filing fee pursuant to section 1.1108. > >DO NOT reply to this e-mail by using the Reply button. In order for your response to be processed expeditiously, you must upload your response via the Internet at www.fcc.gov, Electronic Filing, OET Equipment Authorization Electronic Filing. If the response is submitted through Add Attachments, in order to expedite processing, a message which informs the processing staff that a new exhibit has been submitted must also be submitted via Submit Correspondence. Also, please note that partial responses increase processing time and should not be submitted. > >Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. > 2Printed for Bill Moyer x8-3542 <[email protected]>

1Frank Coperich,9/2/99 10:43 AM -0700,Confidentiality Revisions for Remaining To: "Frank Coperich" <[email protected]> From: Bill Moyer x8-3542 <[email protected]> Subject: Confidentiality Revisions for Remaining Globalstar UT Filings Cc: pguckian, jmoulton, kstambau Bcc: X-Attachments: Frank Coperich: This e-mail will be printed to disk using PDFWriter and submitted as an attachment pdf file to each of the remaining Globalstar UT filings via the filing submissions Webpage. It is also being sent to you directly, because lacking an open correspondence Reference Number for each filing, it is not possible to submit correspondence to those filings. And also so that we will have a record of what was submitted. ----- Per your below appended request and pursuant to the DFUT filing correspondence, here are the revisions to our confidentiality requests (identified by confidentiality request letter item number) for the remaining Globalstar UT filings: We withdraw our request for confidentiality of items 1 through 7 of our SMP UT confidentiality request letter (FCC ID: J9CGSSM1, EA94445). We withdraw our request for confidentiality of items 1 through 10 of our TMP UT confidentiality request letter (FCC ID: J9CGSTM1, EA94735). We withdraw our request for confidentiality of items 1 through 8 of our AFUT confidentiality request letter (FCC ID: J9CGSAF1, EA94736). We withdraw our request for confidentiality of items 1 through 7 of our Car Kit confidentiality request letter (FCC ID: J9CGSCK1, EA94778). -WEM >Date: Thu, 02 Sep 1999 11:13:17 -0400 >From: "Frank Coperich" <[email protected]> >To: wmoyer >Subject: Ref. No. 9479: Requested Information for FCC ID: >J9CGSDF1,EA94247 Filing -Reply >Mime-Version: 1.0 > >Application for EAS 94247 is Granted. > >Ref - Confidentiality - please send any revisions for EAS 94445, 94735, 94736 and 94778 directly that those filings. > > >>>> Bill Moyer x8-3542 <[email protected]> 09/01/99 09:33pm >>> > 1Printed for Bill Moyer x8-3542 <[email protected]>

PORTABLE UT LABEL LOCATIONS LOGO LABEL DEC & HEX ESN Label S/N Label MCN/REV Label PRODUCT ID LABEL, ( FCC ID LABEL) Labels are in same location, on back of phone beneath external battery, for both the Tri-mode Portable UT (shown above) and the Single-Mode Portable UT.

E.11 c photo 01 pict

E.11 c photo 02 pict

E.11 c photo 03 pict

E.11 c photo 04 pict

E.11 c photo 05 pict

E.11 c photo 06 pict

E.11 c photo 07 pict

E.11 c photo 09 pict

E.11 c photo 10 pict

E.11 c photo 11 pict

E.11 c photo 12 pict

TÜV PRODUCT SERVICE 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 619 546 3999 FAX 619 546 0364 Report No. 9324-03 Page 1 of 10 Rev.No 1.0 RADIATED EMISSIONS DATA FOR QUALCOMM, INC. 10300 Campus Point Drive San Diego, CA 92121 Prepared by TÜV PRODUCT SERVICE 10040 Mesa Rim Road San Diego, CA 92121-2912 TÜV PRODUCT SERVICE 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 619 546 3999 FAX 619 546 0364 Report No. 9324-03 Page 2 of 10 Rev.No 1.0 Measurement Requirements (CFR 47 Part 2, Paragraph 2.1053 & Part 22, Paragraph 22.917) The measurements which follow were performed by TÜV Product Service. To the best of my knowledge these tests were conducted in accordance with the procedures outlined in Part 2 of the Commission's Rules and Regulations. The data presented below demonstrates compliance with the appropriate technical standards. _____________________________ Floyd R. Fleury EMC Manager TÜV PRODUCT SERVICE 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 619 546 3999 FAX 619 546 0364 Report No. 9324-03 Page 3 of 10 Rev.No 1.0 Emissions Test Conditions: SPURIOUS RADIATED EMISSIONS The Spurious Radiated Emissions measurements were performed using the following equipment: Test Equipment Used : Model No.Prop. No.DescriptionManufacturerSerial No.Cal Date 8566B720/721Spectrum Analyzer & DisplayHewlett Packard2115A00842 2112A02185 03/00 AA-190-06.00.0657CableUnited Microwave Prod. --N/A AA-190-30.00.0733CableUnited Microwave Prod. --N/A AMF-3D-010180-35-10P752AmplifierMiteq61434405/00 3115453Double Ridge AntennaEMCO9412-436410/99 F4777--High Pass FilterQualcomm--N/A Remarks: TÜV PRODUCT SERVICE 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 619 546 3999 FAX 619 546 0364 Report No. 9324-03 Page 4 of 10 Rev.No 1.0 Testing Facilities Certificates of Approval TÜV PRODUCT SERVICE 10040 Mesa Rim Road San Diego, CA 92121-2912 Phone 619 546 3999 FAX 619 546 0364 Report No. 9324-03 Page 8 of 10 Rev.No 1.0 Photograph of Test Setup

QUALCOMM Proprietary: Restricted Distribution (This document contains critical information about QUALCOMM products and may not be distributed to anyone that is not an employee of Qualcomm without the approval of Configuration Management) Globalstar Tri-Mode Portable User Terminal FCC Part 22 and 25 Certification Report FCC ID: J9CGSTM1 80-98830-1 X1 Applicant: QUALCOMMFCC ID: J9CGSTM1 2 QUALCOMM Incorporated 6455 Lusk Blvd. San Diego, CA, 92121-2779 U.S.A. Copyright © QUALCOMM, Incorporated, 1999. All rights reserved. Printed in the United States of America. All data and information contained in or disclosed by this document are confidential and proprietary information of QUALCOMM Incorporated and all rights therein are expressly reserved. By accepting this material the recipient agrees that this material and the information contained therein are held in confidence and in trust and will not be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of QUALCOMM Incorporated. This technology is controlled by the United States Government. Diversion contrary to U.S. law prohibited. QUALCOMM Proprietary: : Restricted Distribution (This document contains critical information about QUALCOMM products and may not be distributed to anyone that is not an employee of Qualcomm without the approval of Configuration Management) Globalstar™ is a trademark of Loral Qualcomm Satellite Services, Inc. Globalstar Tri-Mode Portable User Terminal FCC Part 25 Certification Report FCC ID: J9CGSTM1 80-98830-1 X1 July 11, 1999 Applicant: QUALCOMMFCC ID: J9CGSTM1 3 M ANUF ACT URER Qualcomm Incorporated 6455 Lusk Boulevard, San Diego, CA 92121-2779 Tel: 619-587-1121 Copyright © 1998 QUALCOMM Incorporated. All rights reserved Printed in the United States of America REG UL AT O RY ENG I NEERI NG MANAG ER Jay Moulton Director of Engineering, Regulatory Location: Qualcomm Building V, Office V-265I Tel: 619-658-3428 Fax: 619-651-xxxx e-mail: [email protected] REG UL AT O RY ENG I NEERI NG SPECI AL IST Paul Guckian Staff/Manager EMC & Regulatory: Gateway Project Location: Qualcomm Inc. Building R office R-202L. Tel: 619-651-1547 Fax: 619-651-1988 e-mail: [email protected] Applicant: QUALCOMMFCC ID: J9CGSTM1 4 Document Amendment Recor d DATE DE TAILS OF CHANG E (a ffec te d pa ge s, etc . ) I S S UE S TATUS MANUFACTURE R AP P ROV AL 7/11/99Initial Document Release1William Moyer Applicant: QUALCOMMFCC ID: J9CGSTM1 5 Ju n e 3 0 , 1 9 9 9 Fe d e ra l C o m m u n ica ti o n s C om m i ssi o n Offi ce o f En g i ne e r i n g a n d Te ch n o l o gy R e :Ap p l ica ti o n fo r C e r ti fi cati o n o f Glo b a l sta r Tr i - M o d e Por ta b l e U se r Te r m in a l FC C ID N o . J9 C GSTM 1 Ge n tle p e o p l e : En cl ose d p l e a se fi n d th e fo l l o w i n g d o cu m e n ta ti o n fo r you r r e vi e w : 1 . FC C Fo r m 7 3 1 , in cl u d i n g th e fe e p r oce ssi n g for m , fo r the Gl o b a l sta r Tr i - M o d e Po r ta b l e Use r Te r m i na l . 2 . A l e tte r fo r R eq u e st fo r co n fi d e n ti al i ty. 3 . N o ti fi ca ti o n o f se p a r a te fe e p a ym e nt su b m i ttal i n th e fo r m o f a ch e ck ( $ 6 1 0.0 0 ) # 1 9 xxxx a n d a cco m p a n yi n g e xe cu te d Fo r m 1 5 9 . 4 .Al l te st d a ta an d su p p o r t d o cu m e n tati o n a s r eq u i r e d fo r ce r ti fi cati o n u n d e r Pa r ts 2 , 2 2 , a n d 2 5 o f Ti tl e 4 7 o f th e C o d e o f Fed e r a l R e g ul a ti o n s C h . 1 ( 1 0 - 1 - 9 8 Ed i ti o n ) . The equipment, QUALCOMM model # GSP 1600, when operating in cellular mode is in full compliance with all parts of EIA/TIA/IS-98-A Mobile Station- Land Station Compatibility Specification, issue July 1996. Information concerning how the cellular phone ESN protection requirements are met is provided in Exhibit 3. If a ny fu r th e r i n fo r m a ti on i s r e q u ir e d p l e a se co n ta ct myse l f o r Pa u l Gu cki an . Yo u ma y co n ta ct m e d i r e ctl y b y p h o ne a t 6 1 9 - 65 8 - 3 5 4 2 , by fa x a t 61 9 - 6 5 1 - 1 9 8 2 , o r b y e - ma i l a t wmo ye r @q u a l co m m .co m . Yo u m a y con ta ct Pa u l Gu ckia n d i r e ctly b y p h o n e a t 6 1 9 - 6 51 - 1 5 4 7 , b y fa x a t 6 19 - 6 5 1 - 1 9 8 8, o r b y e - m a i l a t p g u cki a n @q u a l com m .co m . Pl e a se i n fo r m us w h e n th e R e q u e st fo r C o n fi d en ti a l i ty ha s b e e n a cce p te d a n d a l so w h e n ce r tifi ca ti o n ha s b e e n g ra n te d . Ve r y tr u l y yo u rs, Wi l l ia m E. M o yer Sr . En g i n e e r , EM C & R e g u la to r y Applicant: QUALCOMMFCC ID: J9CGSTM1 6 FC C Fo r m 7 3 1 for Tr i - M o d e Po r ta b l e U se r Te r m in a l Applicant: QUALCOMMFCC ID: J9CGSTM1 7 FC C Fo r m 7 3 1 for Tr i - M o d e Po r ta b l e U se r Te r m in a l ( p . 2 ) Applicant: QUALCOMMFCC ID: J9CGSTM1 8 FC C Fo r m 7 3 1 for Tr i - M o d e Po r ta b l e U se r Te r m in a l ( p . 3 ) Applicant: QUALCOMMFCC ID: J9CGSTM1 9 Fe d e ra l C o m m u n ica ti o n s C om m i ssi o n Ju l y 2 , 1 9 9 9 R e fe re n ce : FC C ID : J9 C GSTM 1 R e q u est fo r C o nfi d e n ti a l ity Pu r sua n t to Se cti o n s 0 .4 57 0 .4 5 9 o f th e C o m m issi o n ’ s r ul e s, Qu a l co m m In co rp o r a te d h er e b y r e q u ests co n fi de n ti a l i ty fo r ce r ta in a sp e cts o f th e i n fo rm a ti o n a cco m p a n yi n g th i s Ap p l ica ti o n fo r C e r ti fi cati o n a s spe ci fi ca l l y i d e n ti fi e d b e l ow : 1. Exh i bi t 5 , TM P U T GS- M o d e Fr e q u e n cy Sta b i l i ty D a ta ( Fi l e: E.5 TM P GS Fr e q . Sta b .p d f) 2. Exh i bi t 6 , Gl o ba l sta r C o mp l i a n ce L ab R e ve r se L i n k Te st Pr o ce d u r e ( Fi l e: E.6 TM P C o m p . L a b TP.p d f) 3. Exh i bi t 7 , Gl o ba l sta r C o mp l i a n ce L ab Gl o b a l sta r - M o d e Out- o f- Ba n d N o i se a n d Sp u r io u s Em i ssio n s Te st Da ta ( Fi l es: E.7 TMP N o i se & Sp u r TR .p df, E.7 b M ax GS An te nn…

Text truncated - open the document above for the full version.

Globalstar Tri-Mode Portable User Terminal Specific Absorption Rate (SAR) Test Report 80-98846-1 X1 QUALCOMM Incorporated 6455 Lusk Blvd. San Diego, CA, 92121-2779 U.S.A. Copyright © QUALCOMM, Incorporated, 1999. All rights reserved. Printed in the United States of America. This technology is controlled by the United States Government. Diversion contrary to U.S. law prohibited. Globalstar™ is a trademark of Loral Qualcomm Satellite Services, Inc. Globalstar Tri-Mode Portable User Terminal Specific Absorption Rate (SAR) Test Report 80-98846-1 X1 July 8, 1999 GLOBALSTAR TRI-MODE PORTABLE USER TERMINAL GSP-1600 SPECIFIC ABSORPTION RATE (SAR) TEST REPORT Prepared By:______________Date: 7-7-99 Dan Laramie Engineer Approved By:______________Date: 7-8-99 Paul Guckian Manager Regulatory Group Company QUALCOMM Inc. Document No. xxxxxxxx GS UT SAR REPORT Issue No: 1 Date July 1999 Equipment GLOBALSTAR GSP 1600 Page Number 2 Dan LaramieFile Ref: CONTENTS 1 INTRODUCTION.................................................................................................................................4 2 SAR TEST FACILITY..........................................................................................................................5 3 APPLICABLE REGULATIONS.......................................................................................................5 4 SAR TEST RESULTS SUMMARY.................................................................................................6 5 TECHNICAL DESCRIPTION............................................................................................................6 5.1 DESCRIPTION OF SAR TEST FACILITY .........................................................................................7 5.2 SAR SYSTEM THEORY...................................................................................................................10 6 TEST SAMPLE OPERATION........................................................................................................13 7 CALIBRATION DATES OF TEST EQUIPMENT........................................................................13 8 SAR TEST SYSTEM VALIDATION.......................................................................................................14 9 SAR MEASUREMENT PROCEDURE......................................................................................................16 10 SAR MEASUREMENT UNCERTAINTY....................................................................................19 11 TEST DATA SUMMARY..........................................................................................................21 12 DRAWINGS / PHOTOS.......................................................................................................27 13 SAR PLOTS..................................................................................Appendix A Company QUALCOMM Inc. Document No. xxxxxxxx GS UT SAR REPORT Issue No: 1 Date July 1999 Equi…

Text truncated - open the document above for the full version.