JLFOPB23 Button Push to Exit

- 4 - Made With Pride In the USA. A manufacturer’s full One Year Warranty covers this product. - 1 - Oracle (TM) 3 Button Access Thank you for purchasing one of the Oracle 3 Button Access p roducts. This product has b een designed and manufactured in the USA, utilizing the highest qualit y standards available. One year limited WARRANTY International Electronics Inc. (IEI) warrants this product to be free of defects in materials and workmanship, for one year. For a period of ON E YEAR following purchase, IEI will repair or replace the product free of charge, including parts, labor, return shipping to you, and handling. After the initial one year of oper ation, the limi ted lifetime warr anty will cover parts, labor, and return shipping to you, with a minimal handling charge specific to the product, as listed below: 3 BUTTON ACCESS: $20.00 If you have installation or operation questions or are in need of warranty service, please contact our Product Support department by email at [email protected] or call 360- 254-1564 Tuesday-Friday 7-5 Pacific Time. If the issue is not resolvable, a manufacturer’s warranty repair order may be issued. To have the product(s) sent for warranty service. A Return Authorization number will be issued for warranty service, which must be put on the outside of the package, to be received and handled properly. Packages for warranty service may be sent to the following address. Packages with no RA# may not be accepted. IEI 5913C NE 127th AVE, Suite 800 Vancouver, WA 98682 Please include a note describing the problem that you are having and a copy of your original sales receipt (within the first year). If the warranty service is outside the first year, please include a check made out to IEI, based on the list of handling fees, shown above. Please note that you may need to send multiple units for warranty service, testing, and upgrading, though only the applic able fee for handling the failed unit(s) will be charged. Please allow 2-4 weeks for service and return shipping. If an EXPEDITED repair/replacement is requested, a 100% surcharge applies. In this case, please write EXPEDITED after the RA number. IEI will attempt to return expedited repair orders within one week, except during holidays. All repairs or replacements are at the discretion of the Manufacturer. This warranty excludes items that have been abused, altered, incorrectly installed, or repaired by an unauthorized person. Changes or modifications not expressly approved by the Manufacturer could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This warranty is limited to the product only. No consequential damages are covered. Part 15.21 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipmen t NOTE The manufacture is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment . International Electronics, Inc. FCC ID: JLF OPB 2 Country Of Origin: USA • Completely Wireless • Up to 1000 Foot Range • Algorithmically Secure • Eliminates Trenching • UV Hardened ABS Enclosure • Button Light When Motion Detected • Audible Confirmation • Pedestal or Surface Mount • Invisible to Lightning OPB3 Patents Pending 4/3/2007 RELAY HOLD MODE ULTRA RX 900- 3 3 BUTTON ACCESS POWER SAVE MODE - 2 - - 3 - TEACHING A 3 BUTTON ACCESS TO AN ULTRA RX 900-3 ERASING THE MEMORY OF THE ULTRX 900- 3 + - POWER Pin 1 and 2 for 10 – 24 VAC Pin 1 and 3 for 10 – 24 VDC CONNECT THE ULTRA RX 900-3 OUTPUT TIMING To place the Ultra RX 900-3 in Learn Mode: Disconnect the power and wait at least 5 seconds. Reapply the power. (The LED will illuminate until the Learn period has expired.When the Learn period has expired, the Ultra RX 900-3 will buzz.) Within 10 seconds, press the learn button on the 3 Button Access unit. Y ou will hear the RX 900-3 buzz and the 3 Button Access will sound a tone indicating the units have learned successfully. If you have additional 3 Button Access units, they can each be taught within 10 seconds of each other or later by repeating this process. If a 3 Button Accessunit was newly taught, the LED on the RX 900-3 will blink 3 times slowly. If NO new units were taught the LED will display 4 blinks, 4 times. Once you are done teaching 3 Button Access units, wait 10 seconds for the Ultra RX 900-3 to leave learn mode. The unit will buzz indicating the Learnperiod is over and the units are ready to use. RELAY 1 Timing modes are determined utilizing the dipswitch located inside the unit. This can be accessed by removing the 1 screw on the bottom of the unit. RELAY 2 RELAY 3 The 3 Button Access is ONLY compatible with the Ultra RX 900-3. Up to 8 3 Button Access units can be taught to 1 Ultra RX 900-3. NOTE: ONLY 1 Ultra RX 900-3 can be taught to 3 Button Access units. A 3 Button Access CANNOT be used to control multiple Ultra RX 900-3 units. Install 4 ‘AA’ batteries into the 3 Button Access. Lithium are preferred in cold climates. - Button 1 (GREEN) operates Relay 1 - Button 2 (WHITE) operates Relay 2 - Button 3 (RED) operates Relay 3 and releases Relays 1 and 2 To reduce the power consumption of the Ultra RX 900-3, dipswitch 7 should be on. This will not take effect until a button is pressed on EACH of the learned 3Button Access units. With dipswitch 8 turned ON, the Ultra RX 900-3 will hold a relay, corresponding to the correct button pressed on the 3 Button Access unit, until the button isreleased. - Remove the screw on the back of the unit. - Press and hold the LEARN button until the LED double blinks, 3 times. o The RX 900 Unit has 3 Relays: • Relay 1: ƒ Pin 11 – Common ƒ Pin 12 – Ch 1 Normal Open ƒ Pin 13 - Ch 1 Norma…

Text truncated - open the document above for the full version.

FCC ID: JLFOPB2 Request for Confidentiality In accordance with 47 C.F.R. Section 0.459, we, Chamberlain Group, Inc., hereby request confidentiality for the block diagram, schematic, active components parts list and product description presented for certification. In support of the Request for Confidentiality, the following is stated: Enclosed within this application is technical information which we deem to be trade secrets and proprietary. If made public, the information might be used to our disadvantage. To assist in assuring that we receive the full value of our product and protect its competitive posture, we respectfully request this grant of confidentiality. Barbara Kelkhoff Manager of Regulatory Affairs Chamberlain Group, Inc. 845 Larch Ave. Elmhurst, IL. 60126

Model OPB3 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: JLFOPB2

Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p07b0013, d07c0008 (866) 311-3268 phone, (480) 926-3598 fax Date: December 6, 2007 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: International Electronics Inc. Equipment: OPB3 FCC ID: JLFOPB3 FCC Rules: 15.249 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Hoosamuddin S. Bandukwala, Lab director Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p07b0013, d07c0008 (866) 311-3268 phone, (480) 926-3598 fax List Of Exhibits (FCC Certification (Transmitters) - Revised 9/28/98) Applicant: International Electronics Inc. FCC ID: JLFOPB3 By Applicant: 1. Letter Of Authorization 2. Identification Drawings Id Label Location Info Attestation Statement (S) Location of Compliance Statement 3. Documentation: 2.1033(B) (3) User Manual (S) (4) Operational Description (5) Block Diagram (5) Schematic Diagram (7) External Photographs Internal Photographs Parts List Active Devices By F.T.L. Inc. A. Testimonial & Statement of Certification B. Statement of Qualifications Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p07b0013, d07c0008 (866) 311-3268 phone, (480) 926-3598 fax Transmitter Certification of FCC ID: JLFOPB3 Model: OPB3 to Federal Communications Commission Rule Part(s)15.249 Date Of Report: December 6, 2007 On the Behalf of the Applicant: International Electronics Inc. 5913-C NE 127th Ave, Suite 800 Vancouver, WA 98682 Attention of: Jim Crider (360) 254-1564 email: [email protected] Supervised By: Hoosamuddin S. Bandu Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p07b0013, d07c0008 (866) 311-3268 phone, (480) 926-3598 fax The applicant has been cautioned as to the following: 15.21 Information to User. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p07b0013, d07c0008 (866) 311-3268 phone, (480) 926-3598 fax Testimonial And Statement Of Certification This is to certify that: 1. That the application was prepared either by, or under the direct supervision of, the undersigned. 2. That the technical data supplied with the application was taken under my direction and supervision. 3. That the data was obtained on representative units, randomly selected. 4. That, to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. Certifying Engineer: Hoosamuddin S. Bandukwala, Lab Director Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p07b0013, d07c0008 (866) 311-3268 phone, (480) 926-3598 fax Table Of Contents Rule Description Page Test Report 1 2.1033(c) General Information Required 2 Standard Test Conditions and Engineering Practices 4 Test Results Summary 4 15.249(a) Fundamental Field Strength 6 15.249(d) Radiated Spurious Emissions 7 RSS 210 99% Occupied Bandwidth 10 . Test Equipment Utilized 11 Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona 85225-7176 p07b0013, d07c0008 (866) 311-3268 phone, (480) 926-3598 fax Page 1 of 12 Required information per ISO 17025-2005, paragraph 5.10.2: a) Test Report b) Laboratory: (FCC: 31040/SIT) (Canada: IC 2044A-1) Flom Test Lab, Inc. 3356 N. San Marcos Place, Suite 107 Chandler, AZ 85225 c) Report Number: d07c0008 d) Client: International Electronics Inc. e) Identification: OPB3 FCC ID: JLFOPB3 Description: f) EUT Condition: Not required unless specified in individual tests. g) Report Date: December 6, 2007 EUT Received: h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with FTL internal quality manual. m) Supervised by: Hoomasuddin S. Bandukwala, Lab Director n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. Flom Test Labs 3356 N. San Marcos Place, Suite 107 Chandler, Arizona …

Text truncated - open the document above for the full version.