KFR-ZL7101US-3Lamp Dimmer Module

Federal Communications Commission Statement This equipment has been followed to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Limited Warranty Vision Guarantees that every wireless lighting module is free from physical defects in material and workmanship under normal use for one year from the date of purchase. If the product proves defective during this one-year warranty period, Vision will replace it free of charge. Vision does not issue any refunds. This warranty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or abuse in handling, or any negligent use; (2) units which have been subject to unauthorized repair, taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages exceeding the cost of the product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. For information on addional devices, plesae visit us at www.visionsecurity.com.tw -3- Operation Manual ZL 7101 US ZL 7101 CN ZL 7101 JP Lamp Dimmer Module ZL 7201 US ZL 7201 CN ZL 7201 JP Appliance On/Off Module (Power Plug In Type) ZL7101/ZL7201 V1 1020717 6B1Z-72001 Introduction Thanks for choosing the Vision’s lighting control of the home automation device. This module is a Z-Wave TM enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave TM enabled network. Every main powered Z-Wave TM enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate “RF dead-sport”. Z-Wave TM enabled devices displaying the Z-Wave TM logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-wave TM enabled networks. This module will send dimmer (ZL 7101) or On/Off (ZL 7201) signal to the appliance that attached to this module by receiving Z-Wave TM signal from controller or manually switch. With special design, this module won’t interfere the other power outlet when plug into the AC outlet. This module also acts as repeater (supporting FLiRS). Product Description and Specification * For indoor use * Specification: Package Content: Protocol: Z-Wave TM (ZM3102N/ZM4102AH) Frequency Range: 908.42MHz (ZL 7101 / ZL 7201 US) 868.42MHz (ZL 7101 / ZL 7201 CN) 920-928 MHz (ZL 7101 / ZL 7201 JP) Operating Range: Up to 100 feet line of sight Operating Temp.: -15°C~ 60°C (5°F~140°F) Operating Voltage: 100~240VAC -1- 1pc ZL 7101, Plug-in Type Dimmer Module Or ZL 7201, Plug-in Type Appliance On/Off Module 1pc User Manual For ZL7101 only Resistive Load: 300W for 110VAC 600W for 220VAC For ZL7201 only Resistive Load: 1800W for 110VAC 3600W for 220VAC Z-Wave™ Command Class: COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_PROTECTION COMMAND_CLASS_SWITCH_ALL COMMAND_CLASS_SWITCH_BINARY (for ZL 7201 only) COMMAND_CLASS_SWITCH_MULTILEVEL (for ZL 7101 only) COMMAND_CLASS_VERSION Operation If you are installing the entire Z-Wave TM system for the first time, please refer to the installation guide of Z-Wave TM Interface Controller before installing ZL 7101 & ZL 7201. 1. For “Inclusion” in (adding to) a network: Put the Z-Wave TM Interface Controller into “inclusion” mode, and following its instruction to add the ZL 7101 or ZL 7201 into your controller. To get in the “Inclusion” mode, the distance between ZL 7101 or ZL 7201 and controller is suggested to be in one meter. By power up to get included for first time, or press program button once to be included. For “Exclusion” from (removing from) a network: Set up the Z-Wave TM Interface Controller into “exclusion” mode, and following its instruction to delete the ZL 7101 or ZL 7201 from your controller. Press program button to be excluded. 2. Manually turn the connected lighting On/Off by your controller or pressing the program button. This is toggle switch. If the light is OFF, pressing the button turns the light ON and vice versa. 3. For ZL 7101 only: Adjust the brightness level of the connected lighting by your controller or pressing and holding the program button. Release the button when the desired level is attained. This is a toggle function. The lighting will dim until the minimum level is attained or the button is released. The next time the button is pressed and held, the level will increase until the maximum level is attained or the button is released. 4. Protection Function: User can use the Protection command class to disable the Program Switch. Protection State=0x00 (Unprotected, Program Switch acts as normal); Protection State=0x01(Protection by sequence, user can manual turn the appli…

Text truncated - open the document above for the full version.

Specification of Antenna Model No.： ZL7101US Antenna Type： PCB Antenna Length Closed： 74mm Length Open： N/A Diameter： 0.9mm No. of element： N/A Antenna Gain： -10 dbm Total Resistance： 1.5Ω Temperature： -20°C ~ 70°C

Compliance Certification Services Inc. Report No.T150129N03 Page A1 / 7 External Photo ( ZL7101US ) Compliance Certification Services Inc. Report No.T150129N03 Page A2 / 7

Compliance Certification Services Inc. Report No.T150129N03 Page A3 / 7 Internal Photo ( ZL7101US ) Compliance Certification Services Inc. Report No.T150129N03 Page A4 / 7 Compliance Certification Services Inc. Report No.T150129N03 Page A5 / 7 Antenna Compliance Certification Services Inc. Report No.T150129N03 Page A6 / 7 RF Module (Chip) Compliance Certification Services Inc. Report No.T150129N03 Page A7 / 7

Description of Operation The is a Z -Wave Light-Dimmer, it ZM3102N (U2) receives RF commands from the MCU (U2) ordered the lamp brightness control to adjust output. The connected light can be turned ON in three ways: 1.With a Z-wave remote. 2.Manually with the pushbutton on the Z-wave module. 3.By the Load-Sensing feature. Normally. The Z-wave module controls the ON/off state of the connected light and power is either turned On or Off at the module (either manually or by the remote). Lf the switch on the connected light is used. The z-wave control circuitry automatically that the light is being turned On and activates The Z-wave controlled outlet. Providing power to the connected device. The device adapts FSK modulation. And the antenna was a PCB Antenna, RF Data rate 9.6 kbps / 40kbps Modulation Frequency Shift Keying (FSK) Frequency deviation Center frequency 908.42MHZ ± 20kHz

Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 34 FCC 47 CFR PART 15 SUBPART C: 2013 ANSI C63.10: 2013 TEST REPORT For Lamp Dimmer Module Model: ZL7101US Brand: Issued to Vision Automobile Electronics Industrial Co., Ltd. No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Issued by Compliance Certification Services Inc. Tainan Lab. No.8,Jiucengling, Xinhua Dist., Tainan City 712, Taiwan (R.O.C.) TEL: (06) 580-2201 FAX: (06) 580-2202 Issued Date: April 08, 2015 Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Page 2 / 34 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 April 08, 2015 Initial Issue ALL Sunny Chang Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Page 3 / 34 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION .........................................................................4 2. EUT DESCRIPTION..............................................................................................5 3. TEST METHODOLOGY........................................................................................6 3.1 EUT CONFIGURATION ...................................................................................6 3.2 EUT EXERCISE ...............................................................................................6 3.3 GENERAL TEST PROCEDURES ....................................................................6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ........................7 3.5 DESCRIPTION OF TEST MODES...................................................................7 4. INSTRUMENT CALIBRATION .............................................................................8 4.1 MEASURING INSTRUMENT CALIBRATION ..................................................8 4.2 MEASUREMENT EQUIPMENT USED ............................................................8 4.3 MEASUREMENT UNCERTAINTY ...................................................................9 5. FACILITIES AND ACCREDITATIONS ...............................................................10 5.1 FACILITIES ....................................................................................................10 5.2 EQUIPMENT ..................................................................................................10 5.3 LABORATORY ACCREDITATIONS LISTING ...............................................10 5.4 TABLE OF ACCREDITATIONS AND LISTINGS............................................11 6. SETUP OF EQUIPMENT UNDER TEST ............................................................12 6.1 SETUP CONFIGURATION OF EUT ..............................................................12 6.2 SUPPORT EQUIPMENT................................................................................12 7. FCC PART 15.249 REQUIREMENTS ................................................................13 7.1 20 DB BANDWIDTH.......................................................................................13 7.2 BAND EDGES MEASUREMENT ...................................................................16 7.3 DUTY CYCLE.................................................................................................17 7.4 SPURIOUS EMISSION..................................................................................19 7.5 POWERLINE CONDUCTED EMISSIONS .....................................................28 APPENDIX I - PHOTOGRAPHS OF TEST SETUP .................................................31 APPENDIX II - PHOTOGRAPHS OF EUT .............................................................. A1 Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Page 4 / 34 1. TEST RESULT CERTIFICATION Product: Lamp Dimmer Module Model: ZL7101US Brand: Applicant: Vision Automobile Electronics Industrial Co., Ltd. No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Manufacturer: Vision Automobile Electronics Industrial Co., Ltd. No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Tested: February 03, 2015 ~ February 25, 2015 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C: 2013 ANSI C63.10 : 2013 No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part 15.107, 15.109,15.207, 15.209 and 15.249. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Jeter Wu Assistant Manager Eric Huang Assistant Section Manager Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Page 5 / 34 2. EUT DESCRIPTION Product Lamp Dimmer Module Model Number ZL7101US Brand Name Received Date January 16, 2015 Frequency Range 908.42MHZ 20kHz Transmit Peak Power 89.10 dBμV/m Data Rate 9.6 kbps , 40kbps Number of Channels 1 Channel Type of Modulation Frequency Shift Keying (FSK) Power Supply AC 120V; 60Hz Antenna Type PCB antenna Model: ZL7101US Gain: -10 dBi RF Module Model ZW0301 Temperature Range -15°C ~ +60°C Remark: 1. Client consigns only one model sample to test (Model Number: ZL7101US). Therefore, the testing Lab. just guarantees the unit, which has been tested. 2. This submittal(s) (test report) is intended fo…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Page 31 / 34 APPENDIX I - PHOTOGRAPHS OF TEST SETUP RADIATED EMISSION MEASUREMENT SETUP Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Page 32 / 34 RADIATED RF MEASUREMENT SETUP Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Page 33 / 34 Compliance Certification Services Inc. FCC ID: KFR-ZL7101US-3 Report No.: T150129N03-RP1 Page 34 / 34 CONDUCTED EMISSION SETUP