KFR-ZL7432USIn-Wall Switch 2 Relays

Operation Turn on or turn off two individual appliances that attached to ZL7432 by Z-Wave™ Interface Controller Federal Communications Commission Statement This equipment has follows with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Limited Warranty Vision Guarantees that every In-Wall Switch module is free from physical defects in material and workmanship under normal use for one year from the date of purchase. If the product proves defective during this one-year warranty period, Vision will replace it free of charge. Vision does not issue any refunds. This warranty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or abuse in handling, or any negligent use; (2) units which have been subject to unauthorized repair, taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages exceeding the cost of the product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. For information on addional devices, plesae visit us at www.visionsecurity.com.tw Installation & Operation Manual ZL 7432 IN ZL 7432 EU ZL 7432 RU ZL 7432 US ZL 7432 IS ZL 7432 JP ZL 7432 BR In-Wall Switch, 2 Relays ZL 7432 V1 1030327 6B1Z-74005 -3- Introduction Thanks for choosing the Vision’s In-Wall Switch module of the home automation device. This module is a Z-Wave™ enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave™ enabled network. Every mains powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate “RF dead-sports”. Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-Wave™ enabled networks. With special design, this module can fit into most of electronic box in the market. This module will send On/Off signal to the appliance that attached to this module by receiving Z-Wave™ signal from controller. It also can control two appliances independently. Product Description and Specification Specification: Package Content Protocol: Z-Wave™ (ZM3102N) Frequency Range: 865.22MHz (ZL7432IN) 868.42MHz (ZL7432EU) 869.00MHz (ZL7432RU) 908.42MHz (ZL7432US) 916.00MHz (ZL7432IS) 920.00MHz (ZL7432JP) 921.42MHz (ZL7432BR) Operating Range: Up to 100 feet line of sight Operating Temp.: -15°C~ 60°C (5°F~140°F) Operating Voltage: 100VAC~240VAC Resistive Load: 550W for 110VAC 1100W for 220VAC 1pc ZL 7432 In-Wall Switch, 2 Relays 1pc Installation & Operation Manual Z-Wave™ Command Class COMMAND_CLASS_ASSOCIATION COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_MULTI_CHANNEL_V3 COMMAND_CLASS_SWITCH_ALL COMMAND_CLASS_SWITCH_BINEARY mapping COMMAND_CLASS_BASIC COMMAND_CLASS_VERSION Installation Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to the installation guide of Z-Wave™ Interface Controller before installing ZL7432 In-Wall Switch Module. 1. Following the wiring diagram to install ZL7432 according to your varied requirements. Note: Place antenna toward the surface and away from metal to get better signal. 2. For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into “inclusion” mode, and following its instruction to add the ZL 7432 to your controller. To get in the “inclusion” mode, the distance between module and controller is suggested to be in one meter. Turn on and turn off the wall switch that connects with ZL 7432 module 4 times to be included. (or press the Program SW 4 times within 2 seconds to be included) For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZL 7432 from your controller. Turn on and turn off the wall switch that connects with ZL 7432 module 4 times to be excluded. (or press the Program SW 4 times within 2 seconds to be excluded) 3. For Wall SW1, ZL 7432 will report the status of On/OFF after doing “Association”. However, Wall SW2 will only report the status if Z-Wave™ Interface Controller support Multi Channel command, and send Get Command to ask ZL 7432 Wall SW 2 to report the status. 4. User can use the following command class to control relay 1 and/or 2 in order to control the appliances that attached to ZL7432 For relay 1: Status of “ON” (Binary Switch Set 0xFF or wall switch ON) Status of “OFF” (Binary Switch Set 0x00 or wall switch OFF) For relay 1 or 2: …

Text truncated - open the document above for the full version.

Specification of Antenna Model No.： ZL7432US Antenna Type： Wire Antenna Length Closed： 95mm Length Open： N/A Diameter： 2.2mm No. of element： N/A Antenna Gain： -13 dbm Total Resistance： 1.7Ω Temperature： -20°C ~ 70°C

Compliance Certification Services Inc. Report No.：T140613N02 Page A1 / 5 External Photo ( ZL7432US )

Diagram Label location Label location FCC ID：KFR-ZL7432US

Compliance Certification Services Inc. Report No.：T140613N02 Page A2 / 5 Internal Photo ( ZL7432US ) Antenna Compliance Certification Services Inc. Report No.：T140613N02 Page A3 / 5 Compliance Certification Services Inc. Report No.：T140613N02 Page A4 / 5 Compliance Certification Services Inc. Report No.：T140613N02 Page A5 / 5

Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 35 FCC 47 CFR PART 15 SUBPART C: 2012 ANSI C63.4: 2009 TEST REPORT For In-Wall Switch 2 Relays Model: ZL7432US Brand: N/A Issued to Vision Automobile Electronics Industrial Co., Ltd No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Issued by Compliance Certification Services Inc. Tainan Lab. No.8,Jiucengling, Xinhua Dist., Tainan City 712, Taiwan (R.O.C.) TEL: (06) 580-2201 FAX: (06) 580-2202 Issued Date: July 2, 2014 Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Page 2 / 35 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 July 2, 2014 Initial Issue ALL Eva Lin Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Page 3 / 35 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION .........................................................................4 2. EUT DESCRIPTION..............................................................................................5 3. TEST METHODOLOGY........................................................................................6 3.1 EUT CONFIGURATION ...................................................................................6 3.2 EUT EXERCISE ...............................................................................................6 3.3 GENERAL TEST PROCEDURES ....................................................................6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ........................7 3.5 DESCRIPTION OF TEST MODES...................................................................7 4. INSTRUMENT CALIBRATION .............................................................................8 4.1 MEASURING INSTRUMENT CALIBRATION ..................................................8 4.2 MEASUREMENT EQUIPMENT USED ............................................................8 4.3 MEASUREMENT UNCERTAINTY ...................................................................9 5. FACILITIES AND ACCREDITATIONS ...............................................................10 5.1 FACILITIES ....................................................................................................10 5.2 EQUIPMENT ..................................................................................................10 5.3 LABORATORY ACCREDITATIONS LISTING ...............................................10 5.4 TABLE OF ACCREDITATIONS AND LISTINGS............................................11 6. SETUP OF EQUIPMENT UNDER TEST ............................................................12 6.1 SETUP CONFIGURATION OF EUT ..............................................................12 6.2 SUPPORT EQUIPMENT................................................................................12 7. FCC PART 15.249 REQUIREMENTS ................................................................13 7.1 20 DB BANDWIDTH.......................................................................................13 7.2 BAND EDGES MEASUREMENT ...................................................................16 7.3 DUTY CYCLE.................................................................................................17 7.4 SPURIOUS EMISSION..................................................................................20 7.5 POWERLINE CONDUCTED EMISSIONS .....................................................29 APPENDIX I - PHOTOGRAPHS OF TEST SETUP .................................................32 APPENDIX II - PHOTOGRAPHS OF EUT .............................................................. A1 Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Page 4 / 35 1. TEST RESULT CERTIFICATION Product: In-Wall Switch 2 Relays Model: ZL7432US Brand: N/A Applicant: Vision Automobile Electronics Industrial Co., Ltd. No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Manufacturer: Vision Automobile Electronics Industrial Co., Ltd. No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Tested: June 16, 2014 ~ June 26, 2014 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C: 2012 ANSI C63.4 : 2009 No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part 15.107, 15.109,15.207, 15.209 and 15.249. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Jeter Wu Assistant Manager Eric Huang Assistant Section Manager Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Page 5 / 35 2. EUT DESCRIPTION Product In-Wall Switch 2 Relays Model Number ZL7432US Brand N/A Received Date June 13, 2014 Frequency Range 908.42MHz ± 20KHz Transmit Peak Power 91.21 dBμV/m Data Rate 9.6 kbps , 40kbps Number of Channels 1 Channel Type of Modulation FSK Power Supply AC 120V Antenna Type Wire antenna Model: ZL7432US Gain: -13 dBi Temperature Range -15°C ~ +60°C Remark: 1. Client consigns only one model sample to test (Model Number: ZL7432US). Therefore, the testing Lab. just guarantees the unit, which has been tested. 2. This submittal(s) (test report) is intended for FCC ID: KFR-ZL7432US filing to comply with Section 15.107 &…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Page 32 / 35 APPENDIX I - PHOTOGRAPHS OF TEST SETUP RADIATED RF EMISSION MEASUREMENT SETUP Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Page 33 / 35 Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Page 34 / 35 RADIATED EMISSION SETUP Compliance Certification Services Inc. FCC ID: KFR-ZL7432US Report No.: T140613N02-RP1 Page 35 / 35 POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP