KFR-ZW4102USZ-Wave Curtain Module Relay Output

Operation 1. Close or open the curtain that attached to ZW4101 or ZW4102 by Z-Wave™ Interface Controller , or manually press the button switch on the curtain. Federal Communications Commission Statement This equipment has been followed with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures: - Reorient or relocate the receiving antenna, - Increase the separation between the equipment and receiver, - Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Limited Warranty Vision Guarantees that every Curtain Control Module is free from physical defects in material and workmanship under normal usage for one year from the date of purchase. If the product proves defective during this one-year warrany period, Vision will replace it free of charge. Vision does not issue any refunds. This warnnty is extended to the original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or abuse in handling, or any negligent usage; (2) units which have been repaired, taken apart, or modified by an unauthorized personnel; (3) units not used in accordance with instruction; (4) damanges exceeding the cost of the produt; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. For information on addional devices, plesae visit us at www.visionsecurity.com.tw Installation & Operation Manual ZW 4101IN ZW 4101EU ZW 4101RU ZW 4101US ZW 4101IS ZW 4101BR ZW 4101JP Z-Wave Curtain Control Module, Signal Output ZW 4102IN ZW 4102EU ZW 4102RU ZW 4102US ZW 4102IS ZW 4102BR ZW 4102JP Z-Wave Curtain Control Module, Relay Output ZW4101/4102 V0 1030318 6B1Z-41001 -3- Introduction Thanks for choosing the Vision’s curtain control module of the home automation device. This module is a Z-Wave™ enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave™ enabled network. Every mains powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate “RF dead-sports” Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-Wave™ enabled networks. Users easily control the curtain to open and close by sending Z-Wave™ signal from Z-Wave™ Interface Controller. This module will send open/close signal to the appliance that attached to this module by receiving Z-Wave™ signal from controller or manually switch. Our special design the curtain not only can be opened and closed but also can be stopped under the Multilevel Switch command on the controller. This module also acts as repeater (supporting FLiRS devices). Product Description and Specification *** For indoor use only *** Specification: Package Content: Protocol: Z-Wave™ (ZM3102N) Frequency Range: 865.22MHz (ZW4101IN/ZW 4102 IN) 868.42MHz (ZW 4101EU/ZW 4102 EU) 869.00MHz (ZW 4101RU/ZW 4102 RU) 908.42MHz (ZW 4101US/ZW 4102 US) 916.00MHz (ZW 4101IS/ZW 4102 IS) 921.42MHz (Z W 4101BR/ZW 4102 BR) 920-928Mhz (ZW4101JP/ZW 4102 JP) Operating Range: Up to 100 feet line of sight Operating Temp.: -15°C~ 60°C (5°F ~140°F) Operating Voltage: 12V Current Consumption: 25mA ZW4101 Signal Output: OPEN output: -VE, 100mA (max) CLOSE output: -VE, 100mA (max) STOP output: -VE, 100mA (max) ZW4102 Relay Output: 1pc 1pc ZW 4101 or ZW 4102 Curtain Control Module Installation & Operation Manual Relay Normal Output: 14VDc, 5A (max) OPEN output: 14VDc, 5A (max) CLOSE output: 14VDc, 5A (max) STOP output: 14VDc, 5A (max) Installation Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to the installation guide of Z-Wave™ Interface Controller before installing ZW 4101 / ZW 4102 Curtain Module. 1. Connect the following wires with curtain’s manual switch or switch’s signal. User can skip switch if it is not necessary. Wire Color ZW 4101 ZW 4102 RED POWER POWER BLACK GROUND GROUND WHITE OPEN SIGNAL OUTPUT OPEN RELAY-COM WHITE/BLACK X OPEN RELAY-NO GRAY CLOSE SIGNAL OUTPUT CLOSE RELAY-COM GRAY/BLACK X CLOSE RELAY-NO BROWN STOP SIGNAL OUTPUT STOP RELAY-COM BROWN/RED X STOP RELAY-NO 2. For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface Controller into“inclusion” mode, and following its instruction to add the ZW 4101 / ZW4102 to your controller. To get in the “inclusion” mode, the distance between module and controller is suggested to be in one meter. Press the program switch on the module once to be included. For “Exclusion” from (removing from) a network: Put the Z-Wave™ Interface Controller into “exclusion” mode, and following its instruction to delete the ZW 4101 / ZW4102 from your controller. Press the program switch on the …

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.T140613N04 Page A1 / 5 External Photo ( ZW4102US ) Compliance Certification Services Inc. Report No.T140613N04 Page A2 / 5

Diagram Label location Label location FCC ID：KFR-ZW4102US

Compliance Certification Services Inc. Report No.T140613N04 Page A3 / 5 Internal Photo ( ZW4102US ) Compliance Certification Services Inc. Report No.T140613N04 Page A4 / 5 Compliance Certification Services Inc. Report No.T140613N04 Page A5 / 5

Description of Operation The EUT is a Z-Wave Curtain Control Module, it ZM3102N(U2) Receiving remote control commands relay output, ZM3102N(U2) via radio frequency to transmit the data to control unit for two-way communication . The device adapts FSK modulation. And the antenna was a Wire Antenna, RF Data rate 9.6 kbps / 40kbps Modulation Frequency Shift Keying (FSK) Frequency deviation Center frequency 908.42MHZ ± 20kHz

Compliance Certification Services Inc. FCC ID:KFR-ZW4102US Report No.:T140613N04-RP1 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 32 FCC 47 CFR PART 15 SUBPART C: 2012 ANSI C63.4: 2009 TEST REPORT For Z-Wave Curtain Module Relay Output Model: ZW4102US Brand: N/A Issued to Vision Automobile Electronics Industrial Co., Ltd No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Issued by Compliance Certification Services Inc. Tainan Lab. No.8,Jiucengling, Xinhua Dist., Tainan City 712, Taiwan (R.O.C.) TEL: (06) 580-2201 FAX: (06) 580-2202 Issued Date: June 30, 2014 Compliance Certification Services Inc. FCC ID:KFR-ZW4102US Report No.:T140613N04-RP1 Page 2 / 32 REVISION HISTORY Rev. Issue Date Revisions Effect Page Revised By 00 June 30, 2014 Initial Issue ALL Sunny Chang Compliance Certification Services Inc. FCC ID:KFR-ZW4102US Report No.:T140613N04-RP1 Page 3 / 32 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION .........................................................................4 2. EUT DESCRIPTION..............................................................................................5 3. TEST METHODOLOGY........................................................................................6 3.1 EUT CONFIGURATION ...................................................................................6 3.2 EUT EXERCISE ...............................................................................................6 3.3 GENERAL TEST PROCEDURES ....................................................................6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ........................7 3.5 DESCRIPTION OF TEST MODES...................................................................7 4. INSTRUMENT CALIBRATION .............................................................................8 4.1 MEASURING INSTRUMENT CALIBRATION ..................................................8 4.2 MEASUREMENT EQUIPMENT USED ............................................................8 4.3 MEASUREMENT UNCERTAINTY ...................................................................9 5. FACILITIES AND ACCREDITATIONS ...............................................................10 5.1 FACILITIES ....................................................................................................10 5.2 EQUIPMENT ..................................................................................................10 5.3 LABORATORY ACCREDITATIONS LISTING ...............................................10 5.4 TABLE OF ACCREDITATIONS AND LISTINGS............................................11 6. SETUP OF EQUIPMENT UNDER TEST ............................................................12 6.1 SETUP CONFIGURATION OF EUT ..............................................................12 6.2 SUPPORT EQUIPMENT................................................................................12 7. FCC PART 15.249 REQUIREMENTS ................................................................13 7.1 20 DB BANDWIDTH.......................................................................................13 7.2 BAND EDGES MEASUREMENT ...................................................................16 7.3 DUTY CYCLE.................................................................................................17 7.4 SPURIOUS EMISSION..................................................................................20 7.5 POWERLINE CONDUCTED EMISSIONS .....................................................29 APPENDIX I - PHOTOGRAPHS OF TEST SETUP .................................................30 APPENDIX II - PHOTOGRAPHS OF EUT .............................................................. A1 Compliance Certification Services Inc. FCC ID:KFR-ZW4102US Report No.:T140613N04-RP1 Page 4 / 32 1. TEST RESULT CERTIFICATION Product: Z-Wave Curtain Module Relay Output Model: ZW4102US Brand: N/A Applicant: Vision Automobile Electronics Industrial Co., Ltd No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Manufacturer: Vision Automobile Electronics Industrial Co., Ltd No. 78, Gongye 3rd Rd., Technology Industrial Park, Tainan City 70955, Taiwan (R.O.C.) Tested: June 18, 2014 ~ June 20, 2014 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C: 2012 ANSI C63.4 : 2009 No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part 15.107, 15.109,15.207, 15.209 and 15.249. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Jeter Wu Assistant Manager Eric Huang Assistant Section Manager Compliance Certification Services Inc. FCC ID:KFR-ZW4102US Report No.:T140613N04-RP1 Page 5 / 32 2. EUT DESCRIPTION Product Z-Wave Curtain Module Relay Output Model Number ZW4102US Brand N/A Received Date June 13, 2014 Frequency Range 908.42MHz 20KHz Transmit Peak Power 87.97 dBμV/m Data Rate 9.6 kbps , 40kbps Number of Channels 1 Channel Type of Modulation FSK Power Supply DC 12V (Powered by Battery) Antenna Type Wire antenna Gain: -14 dBi Temperature Range -15°C ~ +60°C Remark: 1. Client consigns only one model sample to test (Model Number: ZW4102US). Therefore, the testing Lab. just guarantees the unit, which has been tested. 2. This submittal(s) (test report) is intended for FCC ID: KFR-ZW4102US filing to…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. FCC ID:KFR-ZW4102US Report No.:T140613N04-RP1 Page 30 / 32 APPENDIX I - PHOTOGRAPHS OF TEST SETUP RADIATED RF EMISSION MEASUREMENT SETUP Compliance Certification Services Inc. FCC ID:KFR-ZW4102US Report No.:T140613N04-RP1 Page 31 / 32 Compliance Certification Services Inc. FCC ID:KFR-ZW4102US Report No.:T140613N04-RP1 Page 32 / 32 RADIATED EMISSION SETUP