KKGZ1920ET, ST, LT, LT2

® inGround Positioning System (iGPS ® ) Operator’s Manual DIGITAL CONTROL INCORPORATED DCI Headquarters 19625 62 nd Ave. S., Suite B-103 Kent, Washington 98032 USA Tel 425 251 0559 / 800 288 3610 Fax 253 395 2800 E-mail [email protected] www.digitrak.com DCI Europe Kurmainzer Strasse 56 D-97836 Bischbrunn Germany Tel +49(0) 9394 990 990 Fax +49(0) 9394 990 999 [email protected] DCI India SCO # 259, Sector 44-C Chandigarh (UT) 160 047 Punjab, India Tel +91(0) 172 464 0444 Fax +91(0) 172 464 0999 [email protected] DCI China USA Excalibre 2803 Bldg C, 70 Cao Bao Rd Shanghai P.R.C. 200233 Tel +86(0) 21 6432 5186 Fax +86(0) 21 6432 5187 [email protected] DCI Australia 2/9 Frinton Street Southport, Queensland 4215 Australia Tel +61(0) 7 5531 4283 Fax +61(0) 7 5531 2617 [email protected] DCI Russia 420059 Pavlyukhina Street 104, Kazan Russia Tel +7 843 277 52 22 Fax +7 843 277 52 22 [email protected] DIGITAL CONTROL INCORPORATED 3-1100-00-K (English) © 2000-2008 by Digital Control Incorporated. All rights reserved. September 2008 edition. Trademarks The DCI logo, CableLink ® , DataLog ® , DigiTrak ® , Eclipse ® , iGPS ® , Intuitive ® , look-ahead ® , SST ® , target-in- the-box ® , Target Steering ® , and TensiTrak ® are U.S. registered trademarks and DucTrak™, FasTrak™, L T ™, SuperCell™, and TeleLock™ are trademarks of Digital Control Incorporated. Patents The DigiTrak ® Eclipse ® Locating System is covered by one or more of the following U.S. Patents: 5,337,002; 5,633,589; 5,698,981; 5,757,190; 5,764,062; 5,767,678; 5,878,824; 5,914,602; 5,926,025; 5,933,008; 5,990,682; 5,990,683; 6,002,258; 6,005,532; 6,008,651; 6,014,026; 6,035,951; 6,047,783; 6,057,687; 6,079,506; 6,095,260; 6,160,401; 6,232,780; 6,250,402; 6,396,275; 6,417,666; 6,454,023; 6,457,537; 6,496,008; 6,525,538; 6,559,646; 6,653,837; 6,677,768; 6,693,429; 6,756,783; 6,756,784; 6,768,307; 6,838,882; 6,924,645; 6,954,073; 7,015,697; 7,049,820; 7,061,244. Sale of a DigiTrak ® Eclipse ® Receiver does not convey a license under any patents covering the DigiTrak ® Eclipse ® Trans- mitter or underground drill housing. Other patents pending. Limited Warranty All products manufactured and sold by DCI are subject to the terms of a Limited Warranty. A copy of the Limited Warranty is included with this manual along with your DigiTrak ® Eclipse ® Locating System; it can also be obtained by contacting DCI Customer Service, 800-288-3610 or 425-251-0559, or by connecting to DCI's web site, www.digitrak.com. Important Notice All statements, technical information, and recommendations related to the products of Digital Control Incorporated (DCI) are based on information believed to be reliable, but the accuracy or completeness thereof is not warranted. Before utilizing any DCI product, the user should determine the suitability of the product for its intended use. All statements herein refer to DCI products as delivered by DCI and do not apply to any user customizations not authorized by DCI nor to any third-party products. Nothing herein shall constitute any warranty by DCI nor will anything herein be deemed to modify the terms of DCI’s existing Limited Warranty applicable to all DCI products. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Rules of the Federal Communications Commission. These limits are designed to provide reasonable protection against harmful interference in a horizontal directional drilling installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications or inaccurate readings on your DCI locating equipment. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep- tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ¾ Reorient or relocate the DigiTrak ® Eclipse ® Receiver. ¾ Increase the separation between the problematic equipment and the DigiTrak ® Eclipse ® Receiver. ¾ Connect the equipment into an outlet on a different circuit. ¾ Consult the dealer for help. Changes or modifications to the DCI equipment not expressly approved and carried out by DCI will void the user’s Limited Warranty and the FCC’s authorization to operate the equipment. 2 DigiTrak ® Eclipse ® Operator’s Manual DIGITAL CONTROL INCORPORATED Table of Contents SAFETY PRECAUTIONS AND WARNINGS................................................................................................5 INTRODUCTION........................................................................................................................................... 9 RECEIVER .................................................................................................................................................. 11 Power On ............................................................................................................................................... 11 Toggle and Trigger Switches ................................................................................................................. 11 Speaker and Audible Tones................................................................................................................... 12 Adjusting Screen Contrast ..................................................................................................................... 12 Main Menu ............................................................................................................................................. 12 Locate Menu .......................................................................................…

Text truncated - open the document above for the full version.

Directional Drilling Locating System Operator’s Manual DIGITAL CONTROL INCORPORATED DCI Headquarters 19625 62 nd Ave. S., Suite B-103 Kent, Washington 98032 USA Tel 425 251 0559 / 800 288 3610 Fax 253 395 2800 E-mail [email protected] www.digitrak.com DCI Europe Kurmainzer Strasse 56 D-97836 Bischbrunn Germany Tel +49(0) 9394 990 990 Fax +49(0) 9394 990 999 [email protected] DCI India SCO # 259, Sector 44-C Chandigarh (UT) 160 047 Punjab, India Tel +91(0) 172 464 0444 Fax +91(0) 172 464 0999 [email protected] DCI China No. 41, Lane 500, Xingle Road Minhang District Shanghai P.R.C. 201107 Tel +86(0) 21 6432 5186 Fax +86(0) 21 6432 5187 [email protected] DCI Australia 2/9 Frinton Street Southport, Queensland 4215 Australia Tel +61(0) 7 5531 4283 Fax +61(0) 7 5531 2617 [email protected] DCI Russia 420059 Pavlyukhina Street 104, Kazan Russia Tel +7 843 277 52 22 Fax +7 843 277 52 07 [email protected] DIGITAL CONTROL INCORPORATED 3-1050-00-A © 2008 by Digital Control Incorporated. All rights reserved. November 2008 edition. Trademarks The DCI logo, CableLink ® , DataLog ® , DigiTrak ® , Eclipse ® , iGPS ® , Intuitive ® , look-ahead ® , SST ® , target-in- the-box ® , Target Steering ® , and TensiTrak ® are U.S. registered trademarks and DucTrak™, FasTrak™, L T ™, LT2™, SuperCell™, and TeleLock™ and are trademarks of Digital Control Incorporated. Patents The DigiTrak ® LT2™ Locating System is covered by one or more of the following U.S. Patents: 5,337,002; 5,633,589; 5,764,062; 5,767,678; 5,878,824; 5,926,025; 5,933,008; 5,990,682; 6,002,258; 6,005,532; 6,008,651; 6,014,026; 6,035,951; 6,057,687; 6,160,401; 6,232,780; 6,396,275; 6,525,538; 6,559,646; 6,593,745; 6,693,429; 6,756,784; 6,838,881; 6,838,882; 6,924,645; 7,167,005. Sale of a DigiTrak ® LT2™ receiver does not convey a license under any patents covering the DigiTrak ® transmitter or underground drill housing. Other patents pending. Limited Warranty All products manufactured and sold by Digital Control Incorporated (DCI) are subject to the terms of a Limited Warranty. A copy of the Limited Warranty is included with your DigiTrak ® LT2™ Locating System; it can also be obtained by contacting DCI Customer Service, 800-288-3610 or 425-251-0559, or by connecting to DCI's web site, www.digitrak.com. Important Notice All statements, technical information, and recommendations related to the products of DCI are based on information believed to be reliable, but the accuracy or completeness thereof is not warranted. Before utilizing any DCI product, the user should determine the suitability of the product for its intended use. All statements herein refer to DCI products as delivered by DCI and do not apply to any user customizations not authorized by DCI nor to any third-party products. Nothing herein shall constitute any warranty by DCI nor will anything herein be deemed to modify the terms of DCI’s existing limited warranty applicable to all DCI products. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Rules of the Federal Communications Commission. These limits are designed to provide reasonable protection against harmful interference in a horizontal directional drilling installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications or inaccurate readings on your DCI locating equipment. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the DigiTrak ® LT2™ Receiver.  Increase the separation between the problematic equipment and the DigiTrak ® LT2™ Receiver.  Connect the equipment into an outlet on a different circuit.  Consult the dealer for help. Changes or modifications to the DCI equipment not expressly approved and carried out by DCI will void the user’s limited warranty and the FCC’s authorization to operate the equipment. 2 DigiTrak ® LT2™ Operator’s Manual DIGITAL CONTROL INCORPORATED Table of Contents SAFETY PRECAUTIONS AND WARNINGS................................................................................................5 DEAR CUSTOMER:...................................................................................................................................... 7 INTRODUCTION........................................................................................................................................... 9 RECEIVER .................................................................................................................................................. 11 General Description ............................................................................................................................... 11 Power On/Off ......................................................................................................................................... 12 Installing the Battery Pack ................................................................................................................ 12 Turning On the Receiver................................................................................................................... 13 Turning Off the Receiver................................................................................................................... 13 Automatic Shutoff ............................................................................................................................. 13 Main Display Screen ...................................................…

Text truncated - open the document above for the full version.

® ™ Directional Drilling Locating System Operator’s Manual DIGITAL CONTROL INCORPORATED ® DCI Headquarters 19625 62 nd Ave. S., Suite B-103 Kent, Washington 98032 USA Tel 425 251 0559 / 800 288 3610 Fax 253 395 2800 E-mail [email protected] Hwww.digitrak.comH DCI Europe Kurmainzer Strasse 56 D-97836 Bischbrunn Germany Tel +49(0) 9394 990 990 Fax +49(0) 9394 990 999 [email protected] DCI India SCO # 259, Sector 44-C Chandigarh (UT) 160 047 Punjab, India Tel +91(0) 172 464 0444 Fax +91(0) 172 464 0999 [email protected] DCI China USA Excalibre 2803 Bldg C, 70 Cao Bao Rd Shanghai P.R.C. 200233 Tel +86(0) 21 6432 5186 Fax +86(0) 21 6432 5187 [email protected] DCI Australia 2/9 Frinton Street Southport, Queensland 4215 Australia Tel +61(0) 7 5531 4283 Fax +61(0) 7 5531 2617 [email protected] ® 2 Vermeer ® DigiTrak ® L T ™ Operator’s Manual V3-1000-00-B1 Copyright © 2005-2007 by Digital Control Incorporated. All rights reserved. August 2007 Edition. Trademarks The DCI logo, DataLog ® , DigiTrak ® , and target-in-the-box ® are U.S. registered trademarks and L T ™ is a trademark of Digital Control Incorporated. Vermeer and the Vermeer logo are trademarks of Vermeer Manufacturing Company. Patents The DigiTrak ® LT™ Locating System is covered by one or more of the following U.S. Patents: 5,337,002; 5,633,589; 5,764,062; 5,767,678; 5,878,824; 5,926,025; 5,933,008; 5,990,682; 6,002,258; 6,005,532; 6,008,651; 6,014,026; 6,035,951; 6,057,687; 6,160,401; 6,232,780; 6,396,275; 6,525,538; 6,559,646; 6,593,745; 6,693,429; 6,756,784; 6,838,881; 6,838,882; 6,924,645; 7,167,005. Sale of a DigiTrak ® LT™ receiver does not convey a license under any patents covering the DigiTrak ® transmitter or underground drill housing. Other patents pending. Limited Warranty All products manufactured and sold by Digital Control Incorporated (DCI) are subject to the terms of a Limited Warranty. A copy of the Limited Warranty is included with your DigiTrak ® LT™ Locating System; it can also be obtained by contacting DCI Customer Service, 800-288-3610 or 425-251-0559, or by connecting to DCI's web site, www.digitrak.com. Important Notice All statements, technical information, and recommendations related to the products of DCI are based on information believed to be reliable, but the accuracy or completeness thereof is not warranted. Before utilizing any DCI product, the user should determine the suitability of the product for its intended use. All statements herein refer to DCI products as delivered by DCI and do not apply to any user customizations not authorized by DCI nor to any third-party products. Nothing herein shall constitute any warranty by DCI nor will anything herein be deemed to modify the terms of DCI’s existing limited warranty applicable to all DCI products. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Rules of the Federal Communications Commission. These limits are designed to provide reasonable protection against harmful interference in a horizontal directional drilling installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications or inaccurate readings on your DCI locating equipment. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ¾ Reorient or relocate the DigiTrak ® LT™ Receiver. ¾ Increase the separation between the problematic equipment and the DigiTrak ® LT™ Receiver. ¾ Connect the equipment into an outlet on a different circuit. ¾ Consult the dealer for help. Changes or modifications to the DCI equipment not expressly approved and carried out by DCI will void the user’s limited warranty and the FCC’s authorization to operate the equipment. ® Vermeer ® DigiTrak ® L T ™ Operator’s Manual 3 Table of Contents SAFETY PRECAUTIONS AND WARNINGS................................................................................................5 INTRODUCTION........................................................................................................................................... 7 Power Requirements ............................................................................................................................... 8 Environmental Requirements .................................................................................................................. 8 Equipment Maintenance .......................................................................................................................... 8 RECEIVER .................................................................................................................................................... 9 Main Display Screen .............................................................................................................................. 10 Standard Display Screen Symbols ........................................................................................................ 11 Power On/Off ......................................................................................................................................... 12 Proper Handling of Receiver.................................................................................................................. 12 Accessing and Changing Menu Settings ............................................................................................... 13 Receiver Display Menus ................................................................................................................…

Text truncated - open the document above for the full version.

Directional Drilling Locating System Operator’s Manual DIGITAL CONTROL INCORPORATED DCI Headquarters 19625 62nd Ave. S., Suite B-103 Kent, Washington 98032 USA Tel 425 251 0559 / 800 288 3610 Fax 253 395 2800 E-mail [email protected] www.digitrak.com DCI Europe Kurmainzer Strasse 56 D-97836 Bischbrunn Germany Tel +49(0) 9394 990 990 Fax +49(0) 9394 990 999 [email protected] DCI India SCO # 259, Sector 44-C Chandigarh (UT) 160 047 Punjab, India Tel +91(0) 172 464 0444 Fax +91(0) 172 464 0999 [email protected] DCI China No. 41, Lane 500, Xingle Road Huacao Town, Minhang District Shanghai P.R.C. 201107 Tel +86(0) 21 6432 5186 Fax +86(0) 21 6432 5187 [email protected] DCI Australia 2/9 Frinton Street Southport, Queensland 4215 Australia Tel +61(0) 7 5531 4283 Fax +61(0) 7 5531 2617 [email protected] DCI Russia 420059 Pavlyukhina Street 104, Kazan Russia Tel +7 843 277 52 22 Fax +7 843 277 52 07 [email protected] SE ™ DIGITAL CONTROL INCORPORATED 2 DigiTrak ® SE™ Operator’s Manual 3-4200-00-A © 2009 by Digital Control Incorporated. All rights reserved. October 2009. 68BTrademarks The DCI logo, CableLink ® , DataLog ® , DigiTrak ® , Eclipse ® , F2 ® , iGPS ® , MFD ® , SST ® , target-in-the-box ® , Target Steering ® , and TensiTrak ® are U.S. registered trademarks and DucTrak™, F Series™, FSD™, SE™, FasTrak™, LT™, LT2™, SuperCell™, and TeleLock™ are trademarks of Digital Control Incorporated. 69BPatents The DigiTrak ® SE™ Locating System is covered by one or more of the following U.S. Patents: 5,337,002; 5,633,589; 5,990,682; 5,990,683; 6,002,258; 6,005,532; 6,008,651; 6,014,026; 6,035,951; 6,047,783; 6,057,687; 6,095,260; 6,160,401; 6,232,780; 6,250,402; 6,396,275; 6,496,008; 6,525,538; 6,593,745; 6,653,837; 6,693,429; 6,756,784; 6,768,307; 6,838,882; 6,924,645; 7,061,244; 7,080,698; 7,154,273; 7,159,672; 7,167,005; 7,176,690; 7,304,479; 7,309,990; 7,345,486. Sale of a DigiTrak ® SE™ receiver does not convey a license under any patents covering the DigiTrak ® transmitter or underground drill housing. Other patents pending. 70BLimited Warranty All products manufactured and sold by Digital Control Incorporated (DCI) are subject to the terms of a Limited Warranty. A copy of the Limited Warranty is included with your DigiTrak ® SE™ Locating System; it can also be obtained by contacting DCI Customer Service, 800-288-3610 or 425-251-0559, or by connecting to DCI's website, www.digitrak.com. 71BImportant Notice All statements, technical information, and recommendations related to the products of DCI are based on information believed to be reliable, but the accuracy or completeness thereof is not warranted. Before utilizing any DCI product, the user should determine the suitability of the product for its intended use. All statements herein refer to DCI products as delivered by DCI and do not apply to any user customizations not authorized by DCI nor to any third-party products. Nothing herein shall constitute any warranty by DCI nor will anything herein be deemed to modify the terms of DCI’s existing Limited Warranty applicable to all DCI products. 72BFCC Compliance Statement This equipment has been tested and found to comply with the limits for Class A and Class B digital devices, pursuant to Part 15 of the Rules of the Federal Communications Commission. These limits are designed to provide reasonable protection against harmful interference in a horizontal directional drilling installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications or inaccurate readings on your DCI locating equipment. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or tele- vision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the DigiTrak ® SE™ receiver.  Increase the separation between the problematic equipment and the DigiTrak ® SE™ receiver.  Connect the equipment into an outlet on a different circuit.  Consult the dealer for help. Changes or modifications to the DCI equipment not expressly approved and carried out by DCI will void the user’s Limited Warranty and the FCC’s authorization to operate the equipment. DIGITAL CONTROL INCORPORATED DigiTrak ® SE™ Operator’s Manual 3 Table of Contents SAFETY PRECAUTIONS AND WARNINGS ................................................................................................ 5 DEAR CUSTOMER: ...................................................................................................................................... 7 INTRODUCTION ........................................................................................................................................... 9 RECEIVER .................................................................................................................................................. 11 General Description ................................................................................................................................. 11 Power On/Off ........................................................................................................................................... 12 Installing and Removing the Battery Pack ........................................................................................... 12 Turning On the Receiver ...................................................................................................................... 12 Turning Off the Receiver ...................................................................................................................... 14 Automatic Shutdown ......................................…

Text truncated - open the document above for the full version.

Northwest EMC TCB Compliance Opinion Rev. 12/08/09 DIGC0114 Information about the Applicant Grantee (Company Name) Digital Control, Inc. FCC Contact Person Aaron Keyt Address 19625 62nd Avenue South, Suite B103 City, State, Zip Kent, WA 98032 Job Number DIGC0114 Model ET, LT, LT2, ST FCC ID KKGZ1920 Agent Rudy Zeller Approval Type Original Equipment Class DCD Part 15, low power Tx below 1.705 MHz Rule Part 15.209 Overview This application is for an original approval of a 12 kHz transmitter FCC ID:KKGZ1920. This FCC ID: is applied to 4 models of underground drill heads, ET, ST, LT, LT2. The drill heads emit the 12 kHz signal so that a receiver can be used to control the direction of drilling. The receiver for all of these 12 kHz drill heads is the Eclipse. A manual for the receiver has been included in the list of exhibits. Confidentiality requested for allowed files. Request is properly addressed and referenced. A letter assigning Rudy Zeller as agent was received. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature 9/22/2010 Dave Tolman, TCB Committee

ST External Photos with Label ST Label ST Side 1 ST Side 2 ST Rear End ST Front End LT External Photos with Label LT Side 2 LT Side 1 LT Label LT Rear End LT Front End LT2 External Photos with Label LT2 Side 2 LT2 Side 1 LT2 Label LT2 Rear End LT2 Front End ET External Photos with Label ET Side 1 ET Side 2 ET Rear End ET Front End ET Label

ST External Photos with Label ST Label ST Side 1 ST Side 2 ST Rear End ST Front End LT External Photos with Label LT Side 2 LT Side 1 LT Label LT Rear End LT Front End LT2 External Photos with Label LT2 Side 2 LT2 Side 1 LT2 Label LT2 Rear End LT2 Front End ET External Photos with Label ET Side 1 ET Side 2 ET Rear End ET Front End ET Label

ST Internal Transmitter Photos Board with Sensor Module and Battery Housing Circuit board bottom Circuit board top Circuit board top, antenna removed LT2 Internal Transmitter Photos Board with Sensor Module and Battery Housing Circuit board bottom Circuit board top Circuit board top, antenna removed LT Internal Transmitter Photos Board with Sensor Module and Battery Housing Circuit board bottom Circuit board top Circuit board top, antenna removed ET Internal Transmitter Photos Board with Sensor Module and Battery Housing Circuit board bottom Circuit board top Circuit board top, antenna removed

Digital Control, Inc. ST Report No. DIGC0114 Report Prepared By www.nwemc.com 1-888-EMI-CERT © 2010 Northwest EMC, Inc 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: July 20, 2010 Digital Control, Inc. Model: ST Emissions Test Description Specification Test Method Pass/Fail Field Strength of Fundamental FCC 15.209:2010 ANSI C63.10:2009 Pass Field Strength of Spurious Emissions FCC 15.209:2010 ANSI C63.10:2009 Pass Radiated Emissions FCC 15.109:2010 Class A ANSI C63.4:2003 Pass Modifications made to the product See the Modifications section of this report Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834D-1). Approved By: Tim O’Shea, Operations Manager NVLAP Lab Code: 200630-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Northwest EMC Revision History Revision 06/29/09 Barometric Pressure The recorded barometric pressure has been normalized to sea level. Revision Number Description Date Page Number 00 None Accreditations and Authorizations FCC Accredited by NVLAP for performance of FCC radio, digital, and ISM device testing. Our Open Area Test Sites, certification chambers, and conducted measurement facilities have been fully described in reports filed with the FCC and accepted by the FCC in letters maintained in our files. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by the FCC as a Telecommunications Certification Body (TCB). This allows Northwest EMC to certify transmitters to FCC specifications in accordance with 47 CFR 2.960 and 2.962. NVLAP Northwest EMC, Inc. is accredited under the United States Department of Commerce, National Institute of Standards and Technology, and National Voluntary Laboratory Accreditation Program for satisfactory compliance with the requirements of ISO/IEC 17025 for Testing Laboratories. The NVLAP accreditation encompasses Electromagnetic Compatibility Testing in accordance with the European Union EMC Directive 2004/108/EC, and ANSI C63.4. Additionally, Northwest EMC is accredited by NVLAP to perform radio testing in accordance with the European Union R&TTE Directive 1999/5/EEC, the requirements of FCC, and the RSS radio standards for Industry Canada. NVLAP LAB CODE 200629-0 NVLAP LAB CODE 200630-0 NVLAP LAB CODE 200676-0 NVLAP LAB CODE 200761-0 NVLAP LAB CODE 200881-0 Industry Canada Accredited by NVLAP for performance of Industry Canada RSS and ICES testing. Our Open Area Test Sites and certification chambers comply with RSS-Gen, Issue 2 and have been filed with Industry Canada and accepted. Northwest EMC has been accredited by ANSI to ISO / IEC Guide 65 as a product certifier. We have been designated by N…

Text truncated - open the document above for the full version.