KUTWF100Flash light

Wireless Flash Light Model : WF-SD1-CH 1. INTRODUCTION The wireless flash light is a transceiver and designed to monitor the signal from the Skylink dialer model SD-001. When it receives the signal from the dialer, it will flash the light. 2. LEARN THE DIALER TO THE WIRELESS FLASH LIGHT 1) Press the ‘Learn’ button on the flash light unit for 3 seconds as enter to select this programming mode. 2) You will now see the SYS green light flashing quickly. Activate the dialer to send a signal to the Wireless Flash Light unit. 3) Once it learned the dialer successful, The SYS LED stop flashing. Now you can activate the wireless flash light. 3. LEARN WIRELESS FLASH LIGHT UNIT TO DIALER MODEL SD-001 Once the dialer is in programming mode, the green LED will flash one at a time that means you can now add remote controls or sensors to the dialer. 1) Press red button when the green LED is flashing one at a time, as Enter to select this programming mode (Add Remote Controls / Sensors). 2) You will now see both red and green flash one at a time. The red LED now represents you have entered the “Add Remote Controls / Sensors” programming mode. The green LED represents the location you want to add the new remote controls or sensors. There are 4 different locations, 1, 2, 3, or 4. 3) To select location 4, press red button as “Enter” when the green LED is flashing once. 4) Once the location is selected, the dialer will emit 3 beeps indicating you can now press the ‘Learn’ button on the wireless flash light unit to activate. Note: If you press green button again to skip, you will quit from programming. 4. OPERATION When the dialer is activated, this will activate the “learned” wireless flash light unit. 5. LOW BATTERY INDICATION When the wireless flash light unit is being low battery level, it will send signal to activate the ‘Learned’ dialer. 6. BATTERY The wireless flash light operates on 4.8-volt rechargeable battery or DC adapter. This battery does not need to be replaced if used under normal condition. 7. WARRANTY If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase is required. 8. FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 9. CUSTOMER SERVICE SKYLINK TECHNOLOGIES INC., 17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email: [email protected] Website: http://www.skylinkhome.com © 2011 Skylink Group

Tf, :GPL: CAPITAL PROSPEET I;TI}. &n ll3. l$F-, Bbd- E. Verbtnng lnd- Gentq 3+36 Au ftri tffrr Ste{ Fo Ten. H-T . Flong l(rrg. TeL (S521ffiOZ 1318 Fu: (852f ZtOz 468'f EnniL cplk$s$inllnme-com Authoritv to Act as Aeent Date: 2011-06-21 American Certification Body, lnc. 6731 Whittier Avenue Suite C110 Mclean, VA 22101 To Whom lt May Concern: emitel(Shenzhen) limitedis authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certif that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 2l U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: (Typically 8 - 12 months) By: Tirle: On behalf of: Joe Ns (Print name) Canital Prosoect Ltd. (Company Name) Telephone: (852)26021318 I - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 022311 -6

Req uest for Conlidentialitv Date; 2011-06-21 Subject: Confidentiality Request for: @ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part ofthe subject FCC application be held confidential, Type of Confidentiality Requested n Short Term f] Short Term E Short Term I Short Term n Short Term fl Short Term I Short Term f] Short Term I Short term fi Permanent I Permanent*2 I Permanent fl Permanent f] Permanent X Permanent ! Permanent* Exhibit Block Diagrams Extemal Photos Internal Photos Operation DescriptionlTheory of Operation Parts List & PlacemenUBOM Tune-Up Procedure Schematics Test Setup Photos {Jser's Manual Joe Ns *Note: Caoital Prosoect Ltdhas spent substantial effort in developing this product and it is one ofthe first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details ofthe design will result in financial hardship. Permanent Confi dentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary infbrmation not customarily released to the public. Short-Term Confi dentiality: The applicant requests the exhibits selected above as short term contidential be withheld from public view for a period of (soeciff number of d )3- days f-rom the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: (Print name) ttprfu7 , 2 - The asterisked items (*) require furtherjustification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Furtherjustification should be added to the note above. One such example for a potted device would be: "The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable - damage to intemal circuitry. See photographs exhibits that outline the device before and a{ter potting." ' - Please refer to http://acbcert.com/documents/misc-docs,Memo-Short-Teim-Vs-Standard-Confidentialitv.pdf for complete details. a - Must be signed by applicant contact given for applicant on the FCC site, or try the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 022311 -6

PROPRIETARY INFORMATION CPL CAPITAL PROSPECT LTD. MODEL : WF-SD1-CH LABELING DIAGRAM DATE : 15 JUNE, 2011 PAGE : 1 OF 1 BOTTOM CASE LABEL SIZE : 29 X 20mm

FCC Test Report E4064219801KY Type / Model Name: WF-SD1-CH Product Description: Flash light Applicant: Capital Prospect Ltd. FCC ID: KUTWF100 File No. E4064219801KY emitel (Shenzhen)Limited, Building 2，No.171 Meihua Road , Futian District, Shenzhen, P.R.China。 Phone: +86 (755) 8318 2012 Fax: +86 (755) 8312 3810 Email: [email protected] 4_F510_25_Rev2_0 / Date of release: 05-01-2009 / Author: Kidd Yang Page 2 of 18 FCC --- T E S T R E P O R T Test Report No. : E4064219801KY June 21, 2011 ______________________________________________________________________________________________ Date of issue Type / Model Name: WF-SD1-CH Product Description： Flash light Applicant： Capital Prospect Ltd. Address： Room 03, 13/F., Block B, Veristrong Ind. Centre, 34-36 Au Pui Wan Street, Fo Tan, N.T., Hong Kong Test Result according to the standards listed in clause 1 test standards: POSITIVE The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permission of the test laboratory. File No. E4064219801KY emitel (Shenzhen)Limited, Building 2，No.171 Meihua Road , Futian District, Shenzhen, P.R.China。 Phone: +86 (755) 8318 2012 Fax: +86 (755) 8312 3810 Email: [email protected] 4_F510_25_Rev2_0 / Date of release: 05-01-2009 / Author: Kidd Yang Page 3 of 18 Contents 1 TEST STANDARDS 4 2 SUMMARY 5 3 EQUIPMENT UNDER TEST 6 3.1 PHOTO DOCUMENTATION OF THE EUT 6 3.2 POWER SUPPLY SYSTEM UTILISED 7 3.3 SHORT DESCRIPTION OF THE EQUIPMENT UNDER TEST (EUT) 7 4 TEST ENVIRONMENT 8 4.1 ADDRESS OF THE TEST LABORATORY 8 4.2 ENVIRONMENTAL CONDITIONS 8 4.3 STATEMENT OF THE MEASUREMENT UNCERTAINTY 8 5 TEST CONDITIONS AND RESULTS 9 5.1 ANTENNA REQUIREMENT 9 5.2 AVERAGE FACTOR 10 5.3 RADIATED EMISSION 14 5.4 BANDWIDTH 16 5.5 PROVISION OF MOMENTARY OPERATION 17 6 USED TEST EQUIPMENT AND ACCESSORIES 18 File No. E4064219801KY emitel (Shenzhen)Limited, Building 2，No.171 Meihua Road , Futian District, Shenzhen, P.R.China。 Phone: +86 (755) 8318 2012 Fax: +86 (755) 8312 3810 Email: [email protected] 4_F510_25_Rev2_0 / Date of release: 05-01-2009 / Author: Kidd Yang Page 4 of 18 1 TEST STANDARDS The tests were performed according to following standards: FCC Part 15:2009-10-01 Federal Communications Commission, Part 15 – Radio Frequency Device ANSI C63.4:2003 Methods of Measurement of Radio-Noise Emissions from Low- Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz File No. E4064219801KY emitel (Shenzhen)Limited, Building 2，No.171 Meihua Road , Futian District, Shenzhen, P.R.China。 Phone: +86 (755) 8318 2012 Fax: +86 (755) 8312 3810 Email: [email protected] 4_F510_25_Rev2_0 / Date of release: 05-01-2009 / Author: Kidd Yang Page 5 of 18 2 SUMMARY GENERAL REMARKS: N/A FINAL ASSESSMENT: The equipment under test fulfils the FCC requirements cited in test standard listed in section 1. Date of receipt of test sample : June 13, 2011 Testing commenced on : June 13, 2011 Testing concluded on : June 21, 2011 Checked by: Tested by: Ivan Toa Technical Manager Kidd Yang Engineer File No. E4064219801KY emitel (Shenzhen)Limited, Building 2，No.171 Meihua Road , Futian District, Shenzhen, P.R.China。 Phone: +86 (755) 8318 2012 Fax: +86 (755) 8312 3810 Email: [email protected] 4_F510_25_Rev2_0 / Date of release: 05-01-2009 / Author: Kidd Yang Page 6 of 18 3 EQUIPMENT UNDER TEST 3.1 Photo documentation of the EuT Top View Bottom View File No. E4064219801KY emitel (Shenzhen)Limited, Building 2，No.171 Meihua Road , Futian District, Shenzhen, P.R.China。 Phone: +86 (755) 8318 2012 Fax: +86 (755) 8312 3810 Email: [email protected] 4_F510_25_Rev2_0 / Date of release: 05-01-2009 / Author: Kidd Yang Page 7 of 18 3.2 Power supply system utilised Power supply voltage: AC 120V/60Hz DC 4.8V 3.3 Short description of the Equipment under Test (EuT) The EuT is assembled in a case enclosure and act as remote flash light when receive the signal from the sensor. It responds when properly encoded signal modulated on a radio frequency of 433.92MHz. Tested samples: One Set ( model: WF-SD1-CH) Serial number: Not Labelled Dimensions: L: 10.5 cm W:10.5 cm H: 10.0 cm EuT operation mode: The equipment under test was operated during the measurement under the following conditions: - Operation mode 1: Transmitting mode - - EuT configuration: The following interface cables and peripheral devices were connected during the measurements: Interface cables: Interface cable Length Type Line Line termination [m] shielded unshielded Power cable 3.8 2 wires     EuT to Power supply Peripheral devices : Kind of equipment Model and/or Manufacturer Power supply AT10-1200650-U01-F File No. E4064219801KY emitel (Shenzhen)Limited, Building 2，No.171 Meihua Road , Futian District, Shenzhen, P.R.China。 Phone: +86 (755) 8318 2012 Fax: +86 (755) 8312 3810 Email: [email protected] 4_F510_25_Rev2_0 / Date of release: 05-01-2009 / Author: Kidd Yang Page 8 of 18 4 TEST ENVIRONMENT 4.1 Address of the test laboratory emitel (Shenzhen) Limited Building 2, 171 Meihua Road, Futian District, Shenzhen, P.R. China Laboratory registration numbers: FCC Registration number: 746887 4.2 Environmental conditions During the measurement the environmental conditions were within the listed ranges: Temperature: 15-35 ° C Humidity: 30-60 % Atmospheric pressure: 860-1060 mbar 4.3 Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to CISPR 16-4-2 /11.2003 “Uncertainties, statistics and limit modelling – Uncertainty in EMC measurements” and is documented in the quality system acc. to ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer does have the sole responsibil…

Text truncated - open the document above for the full version.