KUTWS100TWireless Remote Transmitter

Skylink wireless remote allows you to operate any electrical appliance (that meets the product's rating) indoors or outdoors without rewiring. Enclosed you will find: -Keychain transmitter with 12-volt alkaline battery installed. -Receiver Plug in the receiver to an electrical outlet (indoors) Plug in the receiver to an electrical outlet fully. The receiver requires a grounded outlet. If you do not have a grounded outlet, please contact an electrician to upgrade your electrical system. Plug in the device you wish to control into the outlet located on the bottom of the receiver Do not exceed the maximum load specifications listed. If you are not sure what is the rating of an appliance, check with an electrician before plugging it into the receiver. Operation RANGE: Up to 100 feet BATTERY (TRANSMITTER): 12-volt alkaline battery INPUT: 120VAC 60Hz MAXIMUM LOAD: RESISTIVE .................... 8A (960W) INCANDESCENT............ 300W Power Outlet WS-100 Wireless Remote Control - IMPORTANT SAFETY INSTRUCTION If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase is required. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Skylink will not be held liable or responsible for any misuse or application of this product other than for its intended use. Note: The National Electrical Code and Canadian Electrical Code (and most local codes) require that outside outlets be protected by a Ground Fault Inter- rupter (GFI). Introduction Installation Specification Press the button on the transmitter (battery already installed), the light on the transmitter will turn on and the device you plugged into the receiver should also be on immediately. Press the button on the trans-mitter again to turn the device off. Battery Replacement Use 12-volt alkaline battery (Type 23A). To replace, open the battery compartment cover, and replace the old battery with a new one. Do not dispose of battery in fire. Battery may explode or leak. Warranty: FCC: WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user’s authority to operate the equipment. If you are using the receiver outdoors, read the extra pre- cautions below. Risk of electric shock, do not use with extension cord or near water or where water may accumulate. Keep plugs and receptacles dry. For use only on GFCI protected circuits. Caution Plug in the receiver to an electrical outlet (outdoors) Plug in the receiver to an electrical outlet fully. Let the receiver hang downward so moisture doesn't accumulate in the outlet. Install cord and unit above ground level with the receptacle in downward position. A weather protective cover must be used in order to prevent rain or moisture from enter- ing the unit. Note: Not for water immer- sion or for use where direct exposed to water. Store in- doors when not in use.

Jul 17, 2001 FEDERAL COMMUNICATIONS COMMISSION 7435 Oakland Mills Road Columbia, MD 21046 U.S.A. Subject: Request for withholding from public disclosure the schematic diagrams and system block diagrams pursuant to an application for certification. Applicant: Capital Prospect Ltd. Product: Wireless Remote Transmitter Model: WS100T FCC ID: KUTWS100T Dear Sir/Madam, We, Capital Prospect Ltd. would like to request that the circuit description, schematic diagrams and system block diagram, submitted with the application for certification be withheld from public disclosure as per Section 0.459 of FCC Rules. This request is made under the provisions of Section 0.457(d) of the Commission's Rules, and Section 552(b)(4) of the Freedom of Information Act. These sections authorize as a withholding from public inspection materials which would be privileged as a matter of law if retained by the person submitting them, and materials which would not customarily be released to the public by that person. The detailed confidential materials are listed as follows: No. Title Drawing No. Sheet No. 1 Circuit Description 2 Block Diagram 3 Schematic Diagrams If you have any queries, please do not hesitate to contact us by our phone numbers: OUR TELEPHONE NO.: (852) 26021318 Yours truly, Joe Ng Project Manager Capital Prospect Ltd. Rm. 16, 13/F., Block. B, Veristrong Ind. Centre, 34-36 Au Pui Wan Street, Fo Tan, N.T., Hong Kong. Tel: (852) 2602 1318 Fax: (852) 2602 4684 Email : [email protected]

ANNEX 2 - EXTERNAL EUT PHOTOS Capital Prospect Ltd. Wireless Remote Control, Model WS100T FCC ID: KUTWS100T Photo 1 of 4 ANNEX 2 - EXTERNAL EUT PHOTOS Capital Prospect Ltd. Wireless Remote Control, Model WS100T FCC ID: KUTWS100T Photo 2 of 4 ANNEX 2 - EXTERNAL EUT PHOTOS Capital Prospect Ltd. Wireless Remote Control, Model WS100T FCC ID: KUTWS100T Photo 3 of 4 ANNEX 2 - EXTERNAL EUT PHOTOS Capital Prospect Ltd. Wireless Remote Control, Model WS100T FCC ID: KUTWS100T Photo 4 of 4

ROOM 16, 13/F., BLOCK B, VERISTRONG IND. CENTRE, 34 AUPUIWAN STREET, FOTAN, N.T., HONG KONG. TEL : (852) 2602 5107 FAX: (852) 2602-4684 EMAIL: [email protected] Ws100tfc.docConfidential InformationJune 30, 2001 12 FCC LABEL AND LOCATION FCC ID: KUTWS100T This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Date: October 8, 1995Sheet 1of 1 SizeDocument NumberREV A66.LBLX1 Title DIAG,FCC LABEL LOCATION APPDDATE 1-OCT-95 DESCRIPTION REVISIONS REV PRELIM RELEASEX1 LET PROPRIETARY INFO CASE FCC LABEL FCC ID: KUTWS100T XXXXXXXXXX FILE DIR: \66 CAPITAL PROSPECT LTD.

ANNEX 3 - INTERNAL EUT PHOTOS Capital Prospect Ltd. Wireless Remote Control, Model WS100T FCC ID: KUTWS100T Photo 1 of 3 ANNEX 3 - INTERNAL EUT PHOTOS Capital Prospect Ltd. Wireless Remote Control, Model WS100T FCC ID: KUTWS100T Photo 2 of 3 ANNEX 3 - INTERNAL EUT PHOTOS Capital Prospect Ltd. Wireless Remote Control, Model WS100T FCC ID: KUTWS100T Photo 3 of 3

Wireless Remote Transmitter Model No.: WS100T FCC ID: KUTWS100T Applicant: Capital Prospect Ltd. Rm 16, 13/F, Block B, Veristrong Ind. Centre, 34 AuPuiWan Street, Fotan, Hong Kong In Accordance With FEDERAL COMMUNICATIONS COMMISSION (FCC) PART 15, SUBPART C, SEC. 15.231 Momentarily Operated Transmitters in 305 to 320 MHz UltraTech's File No.: ULC88-FTX This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: July 12, 2001 Report Prepared by: Dan Huynh Tested by: Vink K, Ngo, RFI/EMI Technicain Issued Date: July 12, 2001 Test Dates: June 22, 2001 The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Telephone (905) 829-1570 Facsimile (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected] FCC PART 15, SUBPART C, Sec. 15.231, MOMENTARILY OPERATED TRANSMITTERS Contents i Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T ULTRATECH GROUP OF LABS File #: ULC88-FTX 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 July 12, 2001 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com • Assessed by ITI (UK) Competent Body, NVLAP (USA) Accreditation Body & ACA/AUSTEL (Australia), VCCI (Japan) • Accredited by Industry Canada (Canada) under ACC-LAB (Europe/Canada MRA and APEC/Canada MRA) • Recognized/Listed by FCC (USA) • All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. SUBMITTAL CHECK LIST ......................................................................................................................1 EXHIBIT 2. INTRODUCTION........................................................................................................................................2 2.1. SCOPE .........................................................................................................................................................................2 2.2. RELATED SUBMITTAL ( S )/ GRANT ( S ) .............................................................................................................................2 2.3. NORMATIVE REFERENCES ............................................................................................................................................2 EXHIBIT 3. PERFORMANCE ASSESSMENT.............................................................................................................3 3.1. CLIENT INFORMATION .................................................................................................................................................3 3.2. EQUIPMENT UNDER TEST ( EUT ) INFORMATION ............................................................................................................3 3.3. EUT ’ S TECHNICAL SPECIFICATIONS .............................................................................................................................4 3.4. ANCILLARY EQUIPMENT ..............................................................................................................................................4 3.5. GENERAL TEST SETUP ..................................................................................................................................................5 EXHIBIT 4. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS .............................6 4.1. CLIMATE TEST CONDITIONS .........................................................................................................................................6 4.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TESTS ...................................................................................6 EXHIBIT 5. SUMMARY OF TEST RESULTS .............................................................................................................7 5.1. LOCATION OF TESTS ....................................................................................................................................................7 5.2. APPLICABILITY & SUMMARY OF EMC EMISSION TEST RESULTS ....................................................................................7 5.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ..................................................................7 EXHIBIT 6. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS .............................8 6.1. TEST PROCEDURES ......................................................................................................................................................8 6.2. MEASUREMENT UNCERTAINTIES ..................................................................................................................................8 6.3. MEASUREMENT EQUIPMENT USED : ..............................................................................................................................8 6.4. ESSENTIAL / PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ...................................................................8 6.5. ANTENNA REQUIREMENTS @ FCC CFR 47, PARA 15.203..............................................................................................9 6.5.1. Limits .................................................................................................................................................................9 6.5.2. Engineering Analysis .........................................................................................................................................9 6.6. PROVISIONS OF FCC 15.231( A ) FOR PERIODIC TRANSMITTERS ...................................................................................10 6.6.1. Engineering Analysis ............................................................................................…

Text truncated - open the document above for the full version.

Wireless Remote Transmitter Model No.: WS100T FCC ID: KUTWS100T Applicant: Capital Prospect Ltd. Rm 16, 13/F, Block B, Veristrong Ind. Centre, 34 AuPuiWan Street, Fotan Hong Kong In Accordance With FEDERAL COMMUNICATIONS COMMISSION (FCC) PART 15, SUBPART C, SEC. 15.231 Momentarily Operated Transmitters in 305 to 320 MHz UltraTech's File No.: ULC88-FTX This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: August 8, 2001 Report Prepared by: Dan Huynh Tested by: Vinh K. Ngo, RFI/EMI Technicain Hung Trinh, RFI/EMI Technicain Issued Date: August 8, 2001 Test Dates: June 22 & August 7, 2001 The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Telephone (905) 829-1570 Facsimile (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected] FCC PART 15, SUBPART C, Sec. 15.231, MOMENTARILY OPERATED TRANSMITTERS Contents i Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T ULTRATECH GROUP OF LABS File #: ULC88-FTX 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 August 8, 2001 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com • Assessed by ITI (UK) Competent Body, NVLAP (USA) Accreditation Body & ACA/AUSTEL (Australia), VCCI (Japan) • Accredited by Industry Canada (Canada) under ACC-LAB (Europe/Canada MRA and APEC/Canada MRA) • Recognized/Listed by FCC (USA) • All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. SUBMITTAL CHECK LIST ......................................................................................................................1 EXHIBIT 2. INTRODUCTION........................................................................................................................................2 2.1. SCOPE .........................................................................................................................................................................2 2.2. RELATED SUBMITTAL ( S )/ GRANT ( S ) .............................................................................................................................2 2.3. NORMATIVE REFERENCES ............................................................................................................................................2 EXHIBIT 3. PERFORMANCE ASSESSMENT.............................................................................................................3 3.1. CLIENT INFORMATION .................................................................................................................................................3 3.2. EQUIPMENT UNDER TEST ( EUT ) INFORMATION ............................................................................................................3 3.3. EUT ’ S TECHNICAL SPECIFICATIONS .............................................................................................................................4 3.4. GENERAL TEST SETUP ..................................................................................................................................................5 EXHIBIT 4. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS .............................6 4.1. CLIMATE TEST CONDITIONS .........................................................................................................................................6 4.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TESTS ...................................................................................6 EXHIBIT 5. SUMMARY OF TEST RESULTS .............................................................................................................7 5.1. LOCATION OF TESTS ....................................................................................................................................................7 5.2. APPLICABILITY & SUMMARY OF EMC EMISSION TEST RESULTS ....................................................................................7 5.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ..................................................................7 EXHIBIT 6. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS .............................8 6.1. TEST PROCEDURES ......................................................................................................................................................8 6.2. MEASUREMENT UNCERTAINTIES ..................................................................................................................................8 6.3. MEASUREMENT EQUIPMENT USED : ..............................................................................................................................8 6.4. ESSENTIAL / PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ...................................................................8 6.5. ANTENNA REQUIREMENTS @ FCC CFR 47, PARA 15.203..............................................................................................9 6.5.1. Limits .................................................................................................................................................................9 6.5.2. Engineering Analysis .........................................................................................................................................9 6.6. PROVISIONS OF FCC 15.231( A ) FOR PERIODIC TRANSMITTERS ...................................................................................10 6.6.1. Engineering Analysis .......................................................................................................................................10 6.7. TRANSMITTER RADIATED EMISSIONS @ 3 METERS , FCC CFR 47, PARA . 15.231( B )…

Text truncated - open the document above for the full version.

Wireless Remote Transmitter Model No.: WS100T FCC ID: KUTWS100T Applicant: Capital Prospect Ltd. Rm 16, 13/F, Block B, Veristrong Ind. Centre, 34 AuPuiWan Street, Fotan Hong Kong In Accordance With FEDERAL COMMUNICATIONS COMMISSION (FCC) PART 15, SUBPART C, SEC. 15.231 Momentarily Operated Transmitters in 304.8 to 314.1 MHz UltraTech's File No.: ULC88-FTX This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: September 28, 2001 Report Prepared by: Dan Huynh Tested by: Vinh K. Ngo, RFI/EMI Technicain Hung Trinh, RFI/EMI Technicain Issued Date: September 28, 2001 Test Dates: Jun. 22, Aug. 7 & Sep. 28, 2001 The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Telephone (905) 829-1570 Facsimile (905) 829-8050 Website: www.ultratech-labs.com Email: [email protected] FCC PART 15, SUBPART C, Sec. 15.231, MOMENTARILY OPERATED TRANSMITTERS Contents i Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T ULTRATECH GROUP OF LABS File #: ULC88-FTX 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 September 28, 2001 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com • Assessed by ITI (UK) Competent Body, NVLAP (USA) Accreditation Body & ACA/AUSTEL (Australia), VCCI (Japan) • Accredited by Industry Canada (Canada) under ACC-LAB (Europe/Canada MRA and APEC/Canada MRA) • Recognized/Listed by FCC (USA) • All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. SUBMITTAL CHECK LIST ......................................................................................................................1 EXHIBIT 2. INTRODUCTION........................................................................................................................................2 2.1. SCOPE .........................................................................................................................................................................2 2.2. RELATED SUBMITTAL ( S )/ GRANT ( S ) .............................................................................................................................2 2.3. NORMATIVE REFERENCES ............................................................................................................................................2 EXHIBIT 3. PERFORMANCE ASSESSMENT.............................................................................................................3 3.1. CLIENT INFORMATION .................................................................................................................................................3 3.2. EQUIPMENT UNDER TEST ( EUT ) INFORMATION ............................................................................................................3 3.3. EUT ’ S TECHNICAL SPECIFICATIONS .............................................................................................................................4 3.4. GENERAL TEST SETUP ..................................................................................................................................................5 EXHIBIT 4. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS .............................6 4.1. CLIMATE TEST CONDITIONS .........................................................................................................................................6 4.2. OPERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TESTS ...................................................................................6 EXHIBIT 5. SUMMARY OF TEST RESULTS .............................................................................................................7 5.1. LOCATION OF TESTS ....................................................................................................................................................7 5.2. APPLICABILITY & SUMMARY OF EMC EMISSION TEST RESULTS ....................................................................................7 5.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ..................................................................7 EXHIBIT 6. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS .............................8 6.1. TEST PROCEDURES ......................................................................................................................................................8 6.2. MEASUREMENT UNCERTAINTIES ..................................................................................................................................8 6.3. MEASUREMENT EQUIPMENT USED : ..............................................................................................................................8 6.4. ESSENTIAL / PRIMARY FUNCTIONS AS DECLARED BY THE MANUFACTURER ...................................................................8 6.5. ANTENNA REQUIREMENTS @ FCC CFR 47, PARA 15.203..............................................................................................9 6.5.1. Limits .................................................................................................................................................................9 6.5.2. Engineering Analysis .........................................................................................................................................9 6.6. PROVISIONS OF FCC 15.231( A ) FOR PERIODIC TRANSMITTERS ...................................................................................10 6.6.1. Engineering Analysis .......................................................................................................................................10 6.7. TRANSMITTER RADIATED EMISSIONS @ 3 METERS , FCC CFR…

Text truncated - open the document above for the full version.

ANNEX 1 - TEST SETUP PHOTOS (Radiated Emissions at 3 Meters Distance) Capital Prospect Ltd. Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T A2 - 1 ANNEX 1 - TEST SETUP PHOTOS (Radiated Emissions at 3 Meters Distance) Capital Prospect Ltd. Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T A2 - 2 ANNEX 1 - TEST SETUP PHOTOS (Radiated Emissions at 3 Meters Distance) Capital Prospect Ltd. Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T A2 - 3 ANNEX 1 - TEST SETUP PHOTOS (Radiated Emissions at 3 Meters Distance) Capital Prospect Ltd. Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T A2 - 4 ANNEX 1 - TEST SETUP PHOTOS (Radiated Emissions at 3 Meters Distance) Capital Prospect Ltd. Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T A2 - 5 ANNEX 1 - TEST SETUP PHOTOS (Radiated Emissions at 3 Meters Distance) Capital Prospect Ltd. Wireless Remote Transmitter, Model WS100T FCC ID: KUTWS100T A2 - 6