L6GALR4200Frequency Selective Repeater

User’s Manual ALR Compact Repeater VD203 67/EN - EnglishFuture on Demand. User’s Manual ALR Compact Repeater Low Power Band Selective Repeater – English ALLGON Systems ABALR Compact Repeater VD203 67/EN - User’s ManualRev. 1A 2000-07i This document describes installation, commissioning and the design of the Allgon ALR Compact Repeater. Communication between the Allgon ALR Compact Repeater and an operator is carried out either by using Allgon OMT32 (Operation and Maintenance Terminal), or Allgon OMS (Operation and Maintenance System). OMT32 is described in the AR Repeaters and OMT32, User’s Manual. OMS is described in the Advanced Repeater OMS, User’s Manual. Hardware and software mentioned in this document are subjected to continuous development and improvement. Consequently, there may be minor discrepancies between the information in the document and the performance and design of the product. Specifications, dimensions and other statements mentioned in this document are subject to change without notice. In this document, the ’<>’ brackets are used to indicate function keys contrary to a series of key strokes ’<Del>’ = the Del(ete) key, ’Del’ = D, e, l. Allgon and its suppliers shall not be liable for any damages related to the software or hardware, or for any other damages whatsoever caused of the use of or inability to use any Allgon product. This is applicable even if Allgon has been advised of the damage risk. Under any circumstances, Allgon’s entire liability shall be limited to replace such defective software or hardware which was originally purchased from Allgon. Teflon is a registered trademark of Du Pont. Other trademarks mentioned in this document are trademarks or registered trademarks of their respective owners. This document is produced by El, Tele & Maskin Ingenjörsfirma AB, Huddinge, Sweden. Printed in Sweden. Allgon Systems AB, SE-187 80 Täby, Sweden Phone: +46 8 540 822 00 – Fax: +46 8 540 834 80 – Internet: www.allgon.com This document or parts of it may not be reproduced without the written permission of Allgon Systems AB. Infringements will be prosecuted. All rights reserved. Copyright © Allgon Systems AB, Sweden, 1994-2000. ALLGON Systems ABALR Compact Repeater VD203 67/EN - User’s ManualRev. 1A 2000-07ii C ontents A bbreviations ............................................................................................................... v 1 . Safety ....................................................................................................................... 1-1 Static Electricity .................................................................................................. 1-2 2 . Introduction ............................................................................................................. 2-1 Repeater Type .................................................................................................... 2-2 Using Repeaters ................................................................................................. 2-3 Shaded Area ................................................................................................. 2-4 Sports Arena ................................................................................................... 2-5 3 . Installation ................................................................................................................ 3-1 Siting the Repeater ............................................................................................ 3-1 Sunshine ......................................................................................................... 3-1 Shelter ............................................................................................................. 3-1 Outdoor Installation and Service Limitations .............................................. 3-1 Dimensions and Weight .................................................................................... 3-2 Mounting ............................................................................................................. 3-3 Connection ........................................................................................................ 3-6 Connection Ports and Station Ground ............................................................ 3-9 Station Ground .............................................................................................. 3-9 P112 PC Port .................................................................................................. 3-10 P113 Parking Device ..................................................................................... 3-10 P118 Repeater to Repeater Link Port .......................................................... 3-10 P119 Alarm Port ............................................................................................. 3-11 P120 Door Switch .......................................................................................... 3-12 P124 Repeater to Repeater Link Port .......................................................... 3-12 P130 RCC Port ............................................................................................... 3-12 Mains Breakdown Relay .................................................................................... 3-13 4 . Commissioning ........................................................................................................ 4-1 Starting the Repeater ........................................................................................ 4-2 Indicators ....................................................................................................... 4-3 Repeater Configuration .................................................................................... 4-4 5 . Functional Description and Design ....................................................................... 5-1 Repeater Design ................................................................................................…

Text truncated - open the document above for the full version.

THP2000 A LLGON T ELECOM , L td. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595- 7999 Toll Free: 1-888-ALLGON1 Attention Please REGARDING: ALR4200 Allgon Compact Repeater 10- 24-00 FCCID L6GALR4200 Grantee Code L6G The Allgon Compact Repeater ALR4200 is compliant with FCC standards when used with the following modulation schemes only. Analogue AMPS (FM) 800 MHz IS136 TDMA ( π /4 DQPSK) 800 MHz IS 95 CDMA (QPSK) 800 MHz The unit should not be used with any system or modulation scheme other than the above mentioned. Allgon Product Management 10-2000/THP

THP2000 A LLGON T ELECOM , L td. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595- 7999 Toll Free: 1-888-ALLGON1 Attention Please REGARDING: ALR4200 Allgon Compact Repeater 10- 24-00 FCCID L6GALR4200 Grantee Code L6G The Allgon Compact Repeater ALR4200 is compliant with FCC standards when used with the following modulation schemes only. Analogue AMPS (FM) 800 MHz IS136 TDMA ( π /4 DQPSK) 800 MHz IS 95 CDMA (QPSK) 800 MHz The unit should not be used with any system or modulation scheme other than the above mentioned. Allgon Product Management 10-2000/THP

ALLGON TELECOM, Ltd. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595-7999 Toll Free: 1-888-ALLGON1 August 25, 2000 Subject: Request for Confidentiality FCC ID: L6GALR4200 Gentlemen: In reference to Section 0.457(d) of the Commission’s Rules, and Section 552(b)(4) of the Freedom of Information Act, Allgon Telecom, LTD. is requesting withholding from public information all schematics. The request for confidentiality is due to a very competitive market and necessity to keep proprietary design by Allgon Telecom, LTD intact. The requested schematics will be submitted in a package or file labeled as “Confidential”. Sincerely, Tim Purvis Product Engineer Allgon Telecom, LTD. cc: Chris Harvey MET Laboratories Inc. 914 W. Patapsco Ave. Baltimore, MD 21230

ALLGON TELECOM, Ltd. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595-7999 Toll Free: 1-888-ALLGON1 ALR4200 Label FCC ID: L6GALR4200 MODEL ALR4200 CANADA MADE IN SWEDEN This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 6 cm 3 cm

ALLGON SYSTEM AB Utfärdare/Issued by Kjell Knuutinen Dattum/Date 1999-10-12 Godkänd/Approved Dok nr/Doc no ALR4200/001-201 Rev A Sida/Page Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION Fil/file ALR4200-001_B1 COMPACT repeater with adjustable bandwidth 800 MHz version 1. Electrical specification Remark Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 – 894 MHz Filter bandwidth standard, adjustable 0.2 – 15 MHz Filter setting resolution 12.5 kHz Duplex spacing 45 MHz Gain adjustment range 45-70 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Output power, PEP Min + 28 dBm TBD 3 rd order intercept point Min + 49 dBm TBD Max absolute group delay 6 μs Noise figure at 65 dB gain, 25° C 5 dB Maximum input power +13 dBm Receiver input port return loss 14 dB RF-connectors N-type female Power supply voltage 85 - 265 VAC Power consumption < 70 W Output power reference table (dBm) No Carrier AMPS CDMA 1 +28 +25 2 +23 +20 4 +19 +16 ALLGON SYSTEM AB Utfärdare/Issued by Kjell Knuutinen Dattum/Date 1999-10-12 Godkänd/Approved Dok nr/Doc no ALR4200/001-201 Rev A Sida/Page Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION Fil/file ALR4200-001_B1 2. Environmental specification Temperature range -13 to + 131 F Temperature range -25 to + 55 °C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches Dimensions. (W x H x D) 385 x 385 x 110 mm Weight < 22 lbs Weight < 10 kg Lock type Allgon Safety bolts ALLGON SYSTEM AB Utfärdare/Issued by Kjell Knuutinen Dattum/Date 1999-10-12 Godkänd/Approved Dok nr/Doc no ALR4200/001-201 Rev A Sida/Page Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION Fil/file ALR4200-001_B1 4. Options and facilities ß Fibre Optic Unit (FOU) ß Remote Communication Control (RCC) for wireless connection ß Battery Back-Up (BBU) with either 25 or 50 Ah battery capacity ß Operation and Maintenance System (OMS) ß Dual band ß Repeater to Repeater (R2R) multi drop link for data communication between all type of Allgon repeaters ß Compatible with OMT and OMS software 5. Operation Set-up and control of the repeater via an OMT (Operation & Maintenance Terminal) software ß PC locally connected via RS232 ß PC remotely connected via modem (optional RCC-kit is required) 7. Software requirements The OMT software package requires at least: ß Windows 95, 98 or NT version 4.0 or higher ß 8 MB of RAM (16 is recommended) ß 4 MB free hard disk space 10. Declaration of conformity - Environmental specification ETS300 019-2-4 - Radio Transmission and Reception ETS300 609-4 - EMC emission and immunity ETS300 342-3 - EMC immunity IEC 801-2,4 and 5 - Electrical safety IEC publication 65 - UL 1950 third Edition - UL CAN/CVSA-C22.2 No 950-M95 - FCC 24E

The unit is factory aligned and calibrated at the time of manufacture. The unit is designed to retain this calibration for the useful life of product. ; therefore no field tune-up or alignment is necessary.

FCC ID: L6GALR4200 October 10, 2000 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention:Applications Examiner Applicant:Allgon Telecom, Ltd. 7317 Jack Newell Blvd. North Fort Worth, Texas 76118 Equipment:COMPACT repeater with adjustable bandwidth, Model ALR4200 FCC ID: L6GALR4200 Specification:47 CFR 22 Licensed Certification Dear Examiner: The following application for Grant of Equipment Authorization is presented on behalf of Allgon Telecom Ltd.. for the Licensed Certification of their Model: ALR4200, Repeater. Enclosed, please find a complete data and documentation package demonstrating that this device complies with the technical requirements of 47 CFR, Part 22, for a Repeater. If you have any questions, please contact the undersigned, who is authorized to act as Agent. Sincerely, Chris Harvey Director, EMC Laboratory FCC ID: L6GALR4200 Met 10030- 2 -October 10, 2000 MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE !! BALTIMORE, MARYLAND 21230-3432 !! PHONE (410) 354-3300 !! FAX (410) 354-3313 ENGINEERING TEST REPORT in support of the Application for Grant of Equipment Authorization EQUIPMENT:COMPACT Repeater, Model ALR4200 FCC ID::L6GALR4200 Specification:47 CFR 22 On Behalf of the Applicant:Allgon Telecom Ltd. 7317 Jack Newell Blvd. North FortWorth, TX 76118 Manufacturer:Allgon Telecom Ltd. 7317 Jack Newell Blvd. North FortWorth, TX 76118 Manufacturer’s Mr. Tim Purvis Representative Test Date(s):August 8 thru September 22, 2000 ENGINEERING STATEMENT I ATTEST: the measurements shown in this report were made in accordance with the procedures indicated, and that the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements. On the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 22 of the FCC Rules under normal use and maintenance. _____________________________ Liming Xu Project Engineer, MET Laboratories FCC ID: L6GALR4200 Met 10030- 3 -October 10, 2000 1.0INTRODUCTION The following data is presented on behalf of the Applicant, Allgon Telecom Ltd. as verification of the compliance of the Allgon COMPACT Repeater, Model ALR4200 to the requirements of 47CFR 22. 2.0TEST SITE All testing was conducted at MET Laboratories, Inc., 914 West Patapsco Avenue, Baltimore, Maryland 21230-3493. Radiated emissions measurements were performed on a three-meter open area test site (OATS). A complete site description is on file with the FCC Laboratory Division as 31040/SIT/MET. 3.0TEST EQUIPMENT USED ManufacturerEquipment Calibration DueCal. Interval Hewlett Packard8563A Spectrum Analyzer5/26/01annual EMCOBiconical Antenna 310404/10/01annual EMCOEMCO Log Periodic Antenna04/10/01annual EMCODouble Ridge Guided Horn2/27/01annual Hewlett Packard8594EM Analyzer11/20/00annual Rhode & Swartz SMIQ03 SG08/16/01annual Hewlett PackardE4431B SG8/29/01annual 4.0EQUIPMENT UNDER TEST CONFIGURATION The Cellular Repeater was configured with AC power supply modules and a digital signal generator was used to simulate various RF (i.e. FM,CDMA or iDEN type) input signals to the EUT. The EUT with host external computer was configured for maximum signal gain and bandwidth. The EUT was operated in a manner representative of the typical usage of the equipment. During all testing, (with the exception of intermodulation tests), the EUT was configured for Single Channel operation which results in maximum possible output gain. 5.0TEST TYPE(S) 5.1Radiated Emissions: 47CFR2.1053, 22.901(d)(2), 22.917(e) 5.2Occupied Bandwidth: 47CFR2.1049, Input vs. Output 5.3RF Power Output: 47CFR 2.1046, 22.913(a) 5.4Spurious Emission at Antenna Terminals:(uplink & downlink) 47CFR 2.1051, 22.917(e) 5.5Intermodulation Distortion 47 CFR 2.1051, 22.917(e) FCC ID: L6GALR4200 Met 10030- 4 -October 10, 2000 E(V/m) 1m ' 49.2X1 1 E(V/m) 1m '7V/mor137dbμV 43%10Log(1)'43dB 137dBμV&43dB'94dBμV@1m E(V/m) 3m ' 49.2X1 3 E(V/m) 3m '2.333V/mor127dbμV 127&43'84dBμV@3m 6.0TEST RESULTS 6.1TEST TYPE: Radiated Emissions 6.1.1TECHNICAL SPECIFICATION:2.1053; 22.901(d)(2), 22.917(e) 6.1.2TEST DATE(S):August 11, 2000 6.1.3MEASUREMENT PROCEDURES: As required by 47 CFR 2.1053, field strength of spurious radiation measurements were made in accordance with the general procedures of ANSI C63.4-1992 "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40 GHz". Preliminary radiated emission measurements were performed inside a shielded chamber with all digital signal generators on and terminated. The frequency list from the preliminary measurements was used as a guide for making final measurements on a 10 meter open area test site. The unit was scanned over the frequency range of 9 kHz to 9 GHz. The Radiated Spurious Emissions Limit is obtained by the following: Based on an output power (as measured at the output of the RF Amplifier) of 1 watts: P o = 1 W As per 2.1053, it is assumed this power is to be fed to a half-wave tuned dipole. Using a conversion formula for distance, the field strength at one meter can be derived: As per 90.210(h), 90.691(a), the spurious emissions must be attenuated by 43 + 10log(P) which is: Therefore, the limit for spurious emissions is: At 3 meters measurement distance, the limit is; According to 24.238(a), all signals must be attenuated by 46.08 dB. Therefore, the limit for spurious emissions for a test distance of 3 meters is: FCC ID: L6GALR4200 Met 10030- 5 -October 10, 2000 6.1.4RESULTS: Frequency (MHz) Azimuth (Degrees) PolarityHeight (Meters) Raw Amplitude (dBuV) A.C.F. (dB)Cable loss (dB) Corrected Amplitude (dBuV/m) Limit (dBuV/m) 52.925 0 H2.216.8611.21.3129.37 84.37 52.925 355V120.9911.741.3134.04 84.37 123.951135H1 .621.9912.922.1737.08 84.37 123.951340V1 21.7912.5…

Text truncated - open the document above for the full version.

FCC ID: L6GALR4200 November 20, 2000 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention:Applications Examiner Applicant:Allgon Telecom, Ltd. 7317 Jack Newell Blvd. North Fort Worth, Texas 76118 Equipment:COMPACT repeater with adjustable bandwidth, Model ALR4200 FCC ID: L6GALR4200 Specification:47 CFR 22 Licensed Certification Dear Examiner: The following application for Grant of Equipment Authorization is presented on behalf of Allgon Telecom Ltd.. for the Licensed Certification of their Model: ALR4200, Repeater. Enclosed, please find a complete data and documentation package demonstrating that this device complies with the technical requirements of 47 CFR, Part 22, for a Repeater. If you have any questions, please contact the undersigned, who is authorized to act as Agent. Sincerely, Chris Harvey Director, EMC Laboratory FCC ID: L6GALR4200 Met 10030- 2 -November 20, 2000 MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE !! BALTIMORE, MARYLAND 21230-3432 !! PHONE (410) 354-3300 !! FAX (410) 354-3313 ENGINEERING TEST REPORT in support of the Application for Grant of Equipment Authorization EQUIPMENT:COMPACT Repeater, Model ALR4200 FCC ID::L6GALR4200 Specification:47 CFR 22 On Behalf of the Applicant:Allgon Telecom Ltd. 7317 Jack Newell Blvd. North FortWorth, TX 76118 Manufacturer:Allgon Telecom Ltd. 7317 Jack Newell Blvd. North FortWorth, TX 76118 Manufacturer’s Mr. Tim Purvis Representative Test Date(s):August 8 thru September 22, 2000 ENGINEERING STATEMENT I ATTEST: the measurements shown in this report were made in accordance with the procedures indicated, and that the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements. On the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 22 of the FCC Rules under normal use and maintenance. _____________________________ Liming Xu Project Engineer, MET Laboratories FCC ID: L6GALR4200 Met 10030- 3 -November 20, 2000 1.0INTRODUCTION The following data is presented on behalf of the Applicant, Allgon Telecom Ltd. as verification of the compliance of the Allgon COMPACT Repeater, Model ALR4200 to the requirements of 47CFR 22. 2.0TEST SITE All testing was conducted at MET Laboratories, Inc., 914 West Patapsco Avenue, Baltimore, Maryland 21230-3493. Radiated emissions measurements were performed on a three-meter open area test site (OATS). A complete site description is on file with the FCC Laboratory Division as 31040/SIT/MET. 3.0TEST EQUIPMENT USED ManufacturerEquipment Calibration DueCal. Interval Hewlett Packard8563A Spectrum Analyzer5/26/01annual EMCOBiconical Antenna 310404/10/01annual EMCOEMCO Log Periodic Antenna04/10/01annual EMCODouble Ridge Guided Horn2/27/01annual Hewlett Packard8594EM Analyzer11/20/00annual Rhode & Swartz SMIQ03 SG08/16/01annual Hewlett PackardE4431B SG8/29/01annual 4.0EQUIPMENT UNDER TEST CONFIGURATION The Cellular Repeater was configured with AC power supply modules and a digital signal generator was used to simulate various RF (i.e. FM,CDMA or iDEN type) input signals to the EUT. The EUT with host external computer was configured for maximum signal gain and bandwidth. The EUT was operated in a manner representative of the typical usage of the equipment. During all testing, (with the exception of intermodulation tests), the EUT was configured for Single Channel operation which results in maximum possible output gain. 5.0TEST TYPE(S) 5.1Radiated Emissions: 47CFR2.1053, 22.901(d)(2), 22.917(e) 5.2Occupied Bandwidth: 47CFR2.1049, Input vs. Output 5.3RF Power Output: 47CFR 2.1046, 22.913(a) 5.4Spurious Emission at Antenna Terminals:(uplink & downlink) 47CFR 2.1051, 22.917(e) 5.5Intermodulation Distortion 47 CFR 2.1051, 22.917(e) FCC ID: L6GALR4200 Met 10030- 4 -November 20, 2000 E(V/m) 1m ' 49.2X1 1 E(V/m) 1m '7V/mor137dbμV 43%10Log(1)'43dB 137dBμV&43dB'94dBμV@1m E(V/m) 3m ' 49.2X1 3 E(V/m) 3m '2.333V/mor127dbμV 127&43'84dBμV@3m 6.0TEST RESULTS 6.1TEST TYPE: Radiated Emissions 6.1.1TECHNICAL SPECIFICATION:2.1053; 22.901(d)(2), 22.917(e) 6.1.2TEST DATE(S):August 11, 2000 6.1.3MEASUREMENT PROCEDURES: As required by 47 CFR 2.1053, field strength of spurious radiation measurements were made in accordance with the general procedures of ANSI C63.4-1992 "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40 GHz". Preliminary radiated emission measurements were performed inside a shielded chamber with all digital signal generators on and terminated. The frequency list from the preliminary measurements was used as a guide for making final measurements on a 10 meter open area test site. The unit was scanned over the frequency range of 9 kHz to 9 GHz. The Radiated Spurious Emissions Limit is obtained by the following: Based on an output power (as measured at the output of the RF Amplifier) of 1 watts: P o = 1 W As per 2.1053, it is assumed this power is to be fed to a half-wave tuned dipole. Using a conversion formula for distance, the field strength at one meter can be derived: As per 90.210(h), 90.691(a), the spurious emissions must be attenuated by 43 + 10log(P) which is: Therefore, the limit for spurious emissions is: At 3 meters measurement distance, the limit is; According to 24.238(a), all signals must be attenuated by 46.08 dB. Therefore, the limit for spurious emissions for a test distance of 3 meters is: FCC ID: L6GALR4200 Met 10030- 5 -November 20, 2000 6.1.4RESULTS: Frequency (MHz) Azimuth (Degrees) PolarityHeight (Meters) Raw Amplitude (dBuV) A.C.F. (dB)Cable loss (dB) Corrected Amplitude (dBuV/m) Limit dBm 52.925 0 H2.216.8611.21.3129.37 -23 52.925 355V120.9911.741.3134.04 -23 123.951135H1 .621.9912.922.1737.08 -23 123.951340V1 21.7912.532.173…

Text truncated - open the document above for the full version.