L6GALR4600Frequency Selective Repeater

User’s Manual ALR Compact Repeater VD203 67/EN - EnglishFuture on Demand. User’s Manual ALR Compact Repeater Low Power Band Selective Repeater – English ALLGON Systems ABALR Compact Repeater VD203 67/EN - User’s ManualRev. 1A 2000-07i This document describes installation, commissioning and the design of the Allgon ALR Compact Repeater. Communication between the Allgon ALR Compact Repeater and an operator is carried out either by using Allgon OMT32 (Operation and Maintenance Terminal), or Allgon OMS (Operation and Maintenance System). OMT32 is described in the AR Repeaters and OMT32, User’s Manual. OMS is described in the Advanced Repeater OMS, User’s Manual. Hardware and software mentioned in this document are subjected to continuous development and improvement. Consequently, there may be minor discrepancies between the information in the document and the performance and design of the product. Specifications, dimensions and other statements mentioned in this document are subject to change without notice. In this document, the ’<>’ brackets are used to indicate function keys contrary to a series of key strokes ’<Del>’ = the Del(ete) key, ’Del’ = D, e, l. Allgon and its suppliers shall not be liable for any damages related to the software or hardware, or for any other damages whatsoever caused of the use of or inability to use any Allgon product. This is applicable even if Allgon has been advised of the damage risk. Under any circumstances, Allgon’s entire liability shall be limited to replace such defective software or hardware which was originally purchased from Allgon. Teflon is a registered trademark of Du Pont. Other trademarks mentioned in this document are trademarks or registered trademarks of their respective owners. This document is produced by El, Tele & Maskin Ingenjörsfirma AB, Huddinge, Sweden. Printed in Sweden. Allgon Systems AB, SE-187 80 Täby, Sweden Phone: +46 8 540 822 00 – Fax: +46 8 540 834 80 – Internet: www.allgon.com This document or parts of it may not be reproduced without the written permission of Allgon Systems AB. Infringements will be prosecuted. All rights reserved. Copyright © Allgon Systems AB, Sweden, 1994-2000. ALLGON Systems ABALR Compact Repeater VD203 67/EN - User’s ManualRev. 1A 2000-07ii C ontents A bbreviations ............................................................................................................... v 1 . Safety ....................................................................................................................... 1-1 Static Electricity .................................................................................................. 1-2 2 . Introduction ............................................................................................................. 2-1 Repeater Type .................................................................................................... 2-2 Using Repeaters ................................................................................................. 2-3 Shaded Area ................................................................................................. 2-4 Sports Arena ................................................................................................... 2-5 3 . Installation ................................................................................................................ 3-1 Siting the Repeater ............................................................................................ 3-1 Sunshine ......................................................................................................... 3-1 Shelter ............................................................................................................. 3-1 Outdoor Installation and Service Limitations .............................................. 3-1 Dimensions and Weight .................................................................................... 3-2 Mounting ............................................................................................................. 3-3 Connection ........................................................................................................ 3-6 Connection Ports and Station Ground ............................................................ 3-9 Station Ground .............................................................................................. 3-9 P112 PC Port .................................................................................................. 3-10 P113 Parking Device ..................................................................................... 3-10 P118 Repeater to Repeater Link Port .......................................................... 3-10 P119 Alarm Port ............................................................................................. 3-11 P120 Door Switch .......................................................................................... 3-12 P124 Repeater to Repeater Link Port .......................................................... 3-12 P130 RCC Port ............................................................................................... 3-12 Mains Breakdown Relay .................................................................................... 3-13 4 . Commissioning ........................................................................................................ 4-1 Starting the Repeater ........................................................................................ 4-2 Indicators ....................................................................................................... 4-3 Repeater Configuration .................................................................................... 4-4 5 . Functional Description and Design ....................................................................... 5-1 Repeater Design ................................................................................................…

Text truncated - open the document above for the full version.

THP2000 A LLGON T ELECOM , L td. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595- 7999 Toll Free: 1-888-ALLGON1 Attention Please REGARDING: ALR4600 Allgon Compact Repeater 10- 24-00 FCCID L6GALR4600 Grantee Code L6G The Allgon Compact Repeater ALR4600 is compliant with FCC standards when used with the following modulation schemes only. Analogue SMR (FM) 800 MHz Digital 16QAM (iDEN  ) 800MHz The unit should not be used with any system or modulation scheme other than the above mentioned. Allgon Product Management 10-2000/THP

THP2000 A LLGON T ELECOM , L td. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595- 7999 Toll Free: 1-888-ALLGON1 Attention Please REGARDING: ALR4600 Allgon Compact Repeater 10- 24-00 FCCID L6GALR4600 Grantee Code L6G The Allgon Compact Repeater ALR4600 is compliant with FCC standards when used with the following modulation schemes only. Analogue SMR (FM) 800 MHz Digital 16QAM (iDEN  ) 800MHz The unit should not be used with any system or modulation scheme other than the above mentioned. Allgon Product Management 10-2000/THP

ALLGON TELECOM, Ltd. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595-7999 Toll Free: 1-888-ALLGON1 August 25, 2000 Subject: Request for Confidentiality FCC ID: L6GALR4600 Gentlemen: In reference to Section 0.457(d) of the Commission’s Rules, and Section 552(b)(4) of the Freedom of Information Act, Allgon Telecom, LTD. is requesting withholding from public information all schematics. The request for confidentiality is due to a very competitive market and necessity to keep proprietary design by Allgon Telecom, LTD intact. The requested schematics will be submitted in a package or file labeled as “Confidential”. Sincerely, Tim Purvis Product Engineer Allgon Telecom, LTD. cc: Chris Harvey MET Laboratories Inc. 914 W. Patapsco Ave. Baltimore, MD 21230

ALLGON TELECOM, Ltd. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595-7999 Toll Free: 1-888-ALLGON1 ALR4600 Label FCC ID: L6GALR4600 MODEL ALR4600 CANADA MADE IN SWEDEN This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 6 cm 3 cm

ALLGON SYSTEM AB Utfärdare/Issued by Kjell Knuutinen Dattum /Date 2000-06-26 Godkänd/ApprovedDok nr/Doc no ALR4600/001-201 Rev C Sida/Page Dok namn/Doc name PRODUCT SPECIFICATION Fil/file 123424 COMPACT repeater with adjustable bandwidth 800 MHz version, iDEN 1. Electrical specification Remark Frequency tuning band Up link 806 – 824 MHz Frequency tuning band Down link 851 – 869 MHz Filter bandwidth standard, adjustable 0.5 – 19 MHz Filter setting resolution 12.5 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 50 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Output power, PEP > + 30 dBm Max absolute group delay 6 μ s Noise figure at 65 dB gain, 25 ° C 7 dB Maximum input power Typical input power –40dBm +13 dBm Receiver input port return loss 14 dB RF-co nnecto rs N-type female Power supply voltage 85 - 265 VAC Po wer co nsumptio n 55 W ALLGON SYSTEM AB Utfärdare/Issued by Kjell Knuutinen Dattum /Date 2000-06-26 Godkänd/ApprovedDok nr/Doc no ALR4600/001-201 Rev C Sida/Page Dok namn/Doc name PRODUCT SPECIFICATION Fil/file 123424 2. Environmental specification Temperature range -13 to + 131 F Temperature range -25 to + 55 ° C Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches Dimensions. (W x H x D) 385 x 385 x 110 mm Weight < 22 lbs Weight < 10 kg Lock type Allgon Safety bolts ALLGON SYSTEM AB Utfärdare/Issued by Kjell Knuutinen Dattum /Date 2000-06-26 Godkänd/ApprovedDok nr/Doc no ALR4600/001-201 Rev C Sida/Page Dok namn/Doc name PRODUCT SPECIFICATION Fil/file 123424 4. Options and facilities ! Fiber Optic Unit (FOU) ! Remote Communication Control (RCC) for wireless connection (TBD) ! Battery Back-Up (BBU) with either 25 or 50 Ah battery capacity ! Operation and Maintenance System (OMS) ! Dual band ! Repeater to Repeater (R2R) multi drop link for data communication between all type of Allgon repeaters ! Compatible with OMT and OMS software 5. Operation Set-up and control of the repeater via an OMT (Operation & Maintenance Terminal) software ! PC locally connected via RS232 ! PC remotely connected via modem (optional RCC-kit is required) 7. Softw are requirements The OMT software package requires at least: ! Windows 95, 98 or NT version 4.0 or higher ! 8 MB of RAM (16 is recommended) ! 4 MB free hard disk space 10. Declaration of conformity - ULTBD - ULTBD - FCCTBD

THP2000 ALLGON TELECOM, Ltd. 7317 Jack Newell Blvd. North, Fort Worth, Texas 76118 www.allgon.com Telephone: (817) 595-9999 Fax: (817) 595-7999 Toll Free: 1-888-ALLGON1 ALR4600 Allgon Compact Repeater 10-25-00 FCCID L6GALR4600 Grantee Code L6G Frequency Stabilization: Allgon repeaters are dependent on the donor (or drive) signal transmitted by the carrier’s base station for re-transmitted frequency stability. The repeater is a transparent amplifier in both uplink and downlink RF paths with no means of frequency generation. Suppression of Spurious Radiation: Allgon repeaters amplify an existing, compliant, donor signal and utilize duplexers, crystal filters, and spurious filters throughout the gain path. Adjustable filters for the pass band attenuate any unwanted ambient signals further. Custom SAW filters assure sharp filter characteristics. Class A amplifier configuration is also utilized for linearity of amplified signal. Modulation Limiting: Allgon repeaters do not modulate the amplified signal. The unit is transparent and passes the received modulated RF from the donor site on the downlink path, and the mobile subscriber unit on the uplink path. Power Limiting: Power limiting is accomplished via microprocessor controlled AGC. A feedback loop for output power via CPL1 through Q3710 (page 12 schematics) is processed and fed to the buss FDET to AN, then to the uP. PLL loops for controlling pass band filtering are monitored via Flock1 and Flock2 on the forward link. If unlock is detected, “RFON” (page 12) is removed and the supply for the final (Q2613) and drivers (Q2506, Q2603) is also removed. Means of output control is accomplished via processor control with PABIAS, FPABIAS (page12) from Q3504 (page17) and the processor input. Gain control is accomplished by inter-stage attenuators via control lines FPATT(page 11), and FGC1A/ FGC1B (page 10). The same is mirrored on the uplink schematics. Active RF Devices: Downlink: Q2102, Q2108, Q2111, Q2202, Q2302, Q2402, Q2406, Q2506 (pre-drive), Q2603 (driver), Q2613 (final). Uplink: Q1102, Q1108, Q1202, Q1302, Q1402, Q1406, Q1502, Q1506 (pre-drive), Q1603 (driver), Q1613 (final). Crystal and Resonator Frequencies: PLL’s X3301 12.8MHz Microprocessor X3102 16.0MHz Memory latch X3101 32.768KHz

The unit is factory aligned and calibrated at the time of manufacture. IT is designed to retain this calibration for the life of the product. Because of this manufacture process, there is nofield tune-up or alignment necessary.

FCC ID: L6GALR4600 October 31, 2000 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention:Applications Examiner Applicant:Allgon Telecom, Ltd. 7317 Jack Newell Blvd. North Fort Worth, Texas 76118 Equipment:COMPACT repeater with adjustable bandwidth, Model ALR4600 FCC ID: L6GALR4600 Specification:47 CFR 90 Licensed Certification Dear Examiner: The following application for Grant of Equipment Authorization is presented on behalf of Allgon Telecom Ltd.. for the Licensed Certification of their Model: ALR4600, Repeater. Enclosed, please find a complete data and documentation package demonstrating that this device complies with the technical requirements of 47 CFR, Part 90, for a Repeater. If you have any questions, please contact the undersigned, who is authorized to act as Agent. Sincerely, Chris Harvey Director, EMC Laboratory FCC ID: L6GALR4600 Met 10023- 2 -October 31, 2000 MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE !! BALTIMORE, MARYLAND 21230-3432 !! PHONE (410) 354-3300 !! FAX (410) 354-3313 ENGINEERING TEST REPORT in support of the Application for Grant of Equipment Authorization EQUIPMENT:COMPACT Repeater, Model ALR4600 FCC ID::L6GALR4600 Specification:47 CFR 90 On Behalf of the Applicant:Allgon Telecom Ltd. 7317 Jack Newell Blvd. North FortWorth, TX 76118 Manufacturer:Allgon Telecom Ltd. 7317 Jack Newell Blvd. North FortWorth, TX 76118 Manufacturer’s Mr. Tim Purvis Representative Test Date(s):September 20 thru 29 , 2000 ENGINEERING STATEMENT I ATTEST: the measurements shown in this report were made in accordance with the procedures indicated, and that the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements. On the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 90 of the FCC Rules under normal use and maintenance. _____________________________ Liming Xu Project Engineer, MET Laboratories FCC ID: L6GALR4600 Met 10023- 3 -October 31, 2000 1.0INTRODUCTION The following data is presented on behalf of the Applicant, Allgon Telecom Ltd. as verification of the compliance of the Allgon COMPACT Repeater, Model ALR4600 to the requirements of 47CFR 90. 2.0TEST SITE All testing was conducted at MET Laboratories, Inc., 914 West Patapsco Avenue, Baltimore, Maryland 21230-3493. Radiated emissions measurements were performed on a three-meter open area test site (OATS). A complete site description is on file with the FCC Laboratory Division as 31040/SIT/MET. 3.0TEST EQUIPMENT USED ManufacturerEquipment Calibration DueCal. Interval Hewlett Packard8563A Spectrum Analyzer5/26/01annual EMCOBiconical Antenna 310403/06/01annual EMCOEMCO Log Periodic Antenna10/20/00annual EMCODouble Ridge Guided Horn2/27/01annual Hewlett Packard8594EM Analyzer11/20/00annual Rhode & Swartz SMIQ03 SG08/16/01annual Hewlett PackardE4431B SG8/29/01annual 4.0EQUIPMENT UNDER TEST CONFIGURATION The Cellular Repeater was configured with AC power supply modules and a digital signal generator was used to simulate various RF (i.e. FM or iDEN type) input signals to the EUT. The EUT with host external computer was configured for maximum signal gain and bandwidth. The EUT was operated in a manner representative of the typical usage of the equipment. During all testing, (with the exception of intermodulation tests), the EUT was configured for Single Channel operation which results in maximum possible output gain. 5.0TEST TYPE(S) 5.1Radiated Emissions: 47CFR2.1053, 90.210(h)/.691(a) 5.2Occupied Bandwidth: 47CFR2.1049, Input vs. Output 5.3RF Power Output: 47CFR 2.1046, 90.205(i), (90.635) 5.4Spurious Emission at Antenna Terminals:(uplink & downlink) 47CFR 2.1051, 90.210(h)/.691(a) 5.5Intermodulation Distortion FCC ID: L6GALR4600 Met 10023- 4 -October 31, 2000 E(V/m) 1m ' 49.2X1 1 E(V/m) 1m '7V/mor137dbμV 43%10Log(1)'43dB 137dBμV&43dB'94dBμV@1m E(V/m) 3m ' 49.2X1 3 E(V/m) 3m '2.333V/mor127dbμV 127&43'84dBμV@3m 6.0TEST RESULTS 6.1TEST TYPE: Radiated Emissions 6.1.1TECHNICAL SPECIFICATION:2.1053; 90.210(h), 90.691(a) 6.1.2TEST DATE(S):September 29, 2000 6.1.3MEASUREMENT PROCEDURES: As required by 47 CFR 2.1053, field strength of spurious radiation measurements were made in accordance with the general procedures of ANSI C63.4-1992 "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40 GHz". Preliminary radiated emission measurements were performed inside a shielded chamber with all digital signal generators on and terminated. The frequency list from the preliminary measurements was used as a guide for making final measurements on a 10 meter open area test site. The unit was scanned over the frequency range of 9 kHz to 9 GHz. The Radiated Spurious Emissions Limit is obtained by the following: Based on an output power (as measured at the output of the RF Amplifier) of 1 watts: P o = 1 W As per 2.1053, it is assumed this power is to be fed to a half-wave tuned dipole. Using a conversion formula for distance, the field strength at one meter can be derived: As per 90.210(h), 90.691(a), the spurious emissions must be attenuated by 43 + 10log(P) which is: Therefore, the limit for spurious emissions is: At 3 meters measurement distance, the limit is; According to 24.238(a), all signals must be attenuated by 46.08 dB. Therefore, the limit for spurious emissions for a test distance of 3 meters is: FCC ID: L6GALR4600 Met 10023- 5 -October 31, 2000 6.1.4RESULTS: Frequency (MHz) Azimuth (Degrees) PolarityHeight (Meters) Raw Amplitude (dBuV) A.C.F. (dB)Cable loss (dB) Corrected Amplitude (dBuV/m) Limit (dBuV/m) 127.34 360 H1.3620.113.3 2.1235.53 84.37 127.34 60V125.34 13.972.1241.43 84.37 56.38 328H1 .3614.9 11.31.3727.57 84.37 56.38 0V1 13.4 10.4551.3725.23 84.37 361.00…

Text truncated - open the document above for the full version.

FCC ID: L6GALR4600 November 20, 2000 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention:Applications Examiner Applicant:Allgon Telecom, Ltd. 7317 Jack Newell Blvd. North Fort Worth, Texas 76118 Equipment:COMPACT repeater with adjustable bandwidth, Model ALR4600 FCC ID: L6GALR4600 Specification:47 CFR 90 Licensed Certification Dear Examiner: The following application for Grant of Equipment Authorization is presented on behalf of Allgon Telecom Ltd.. for the Licensed Certification of their Model: ALR4600, Repeater. Enclosed, please find a complete data and documentation package demonstrating that this device complies with the technical requirements of 47 CFR, Part 90, for a Repeater. If you have any questions, please contact the undersigned, who is authorized to act as Agent. Sincerely, Chris Harvey Director, EMC Laboratory FCC ID: L6GALR4600 Met 10023- 2 -November 20, 2000 MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE !! BALTIMORE, MARYLAND 21230-3432 !! PHONE (410) 354-3300 !! FAX (410) 354-3313 ENGINEERING TEST REPORT in support of the Application for Grant of Equipment Authorization EQUIPMENT:COMPACT Repeater, Model ALR4600 FCC ID::L6GALR4600 Specification:47 CFR 90 On Behalf of the Applicant:Allgon Telecom Ltd. 7317 Jack Newell Blvd. North FortWorth, TX 76118 Manufacturer:Allgon Telecom Ltd. 7317 Jack Newell Blvd. North FortWorth, TX 76118 Manufacturer’s Mr. Tim Purvis Representative Test Date(s):September 20 thru 29 , 2000 ENGINEERING STATEMENT I ATTEST: the measurements shown in this report were made in accordance with the procedures indicated, and that the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements. On the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of Part 90 of the FCC Rules under normal use and maintenance. _____________________________ Liming Xu Project Engineer, MET Laboratories FCC ID: L6GALR4600 Met 10023- 3 -November 20, 2000 1.0INTRODUCTION The following data is presented on behalf of the Applicant, Allgon Telecom Ltd. as verification of the compliance of the Allgon COMPACT Repeater, Model ALR4600 to the requirements of 47CFR 90. 2.0TEST SITE All testing was conducted at MET Laboratories, Inc., 914 West Patapsco Avenue, Baltimore, Maryland 21230-3493. Radiated emissions measurements were performed on a three-meter open area test site (OATS). A complete site description is on file with the FCC Laboratory Division as 31040/SIT/MET. 3.0TEST EQUIPMENT USED ManufacturerEquipment Calibration DueCal. Interval Hewlett Packard8563A Spectrum Analyzer5/26/01annual EMCOBiconical Antenna 310403/06/01annual EMCOEMCO Log Periodic Antenna10/20/00annual EMCODouble Ridge Guided Horn2/27/01annual Hewlett Packard8594EM Analyzer11/20/00annual Rhode & Swartz SMIQ03 SG08/16/01annual Hewlett PackardE4431B SG8/29/01annual 4.0EQUIPMENT UNDER TEST CONFIGURATION The Cellular Repeater was configured with AC power supply modules and a digital signal generator was used to simulate various RF (i.e. FM or iDEN type) input signals to the EUT. The EUT with host external computer was configured for maximum signal gain and bandwidth. The EUT was operated in a manner representative of the typical usage of the equipment. During all testing, (with the exception of intermodulation tests), the EUT was configured for Single Channel operation which results in maximum possible output gain. 5.0TEST TYPE(S) 5.1Radiated Emissions: 47CFR2.1053, 90.210(h)/.691(a) 5.2Occupied Bandwidth: 47CFR2.1049, Input vs. Output 5.3RF Power Output: 47CFR 2.1046, 90.205(i), (90.635) 5.4Spurious Emission at Antenna Terminals:(uplink & downlink) 47CFR 2.1051, 90.210(h)/.691(a) 5.5Intermodulation Distortion FCC ID: L6GALR4600 Met 10023- 4 -November 20, 2000 E(V/m) 1m ' 49.2X1 1 E(V/m) 1m '7V/mor137dbμV 43%10Log(1)'43dB 137dBμV&43dB'94dBμV@1m E(V/m) 3m ' 49.2X1 3 E(V/m) 3m '2.333V/mor127dbμV 127&43'84dBμV@3m 6.0TEST RESULTS 6.1TEST TYPE: Radiated Emissions 6.1.1TECHNICAL SPECIFICATION:2.1053; 90.210(h), 90.691(a) 6.1.2TEST DATE(S):September 29, 2000 6.1.3MEASUREMENT PROCEDURES: As required by 47 CFR 2.1053, field strength of spurious radiation measurements were made in accordance with the general procedures of ANSI C63.4-1992 "Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9kHz to 40 GHz". Preliminary radiated emission measurements were performed inside a shielded chamber with all digital signal generators on and terminated. The frequency list from the preliminary measurements was used as a guide for making final measurements on a 10 meter open area test site. The unit was scanned over the frequency range of 9 kHz to 9 GHz. The Radiated Spurious Emissions Limit is obtained by the following: Based on an output power (as measured at the output of the RF Amplifier) of 1 watts: P o = 1 W As per 2.1053, it is assumed this power is to be fed to a half-wave tuned dipole. Using a conversion formula for distance, the field strength at one meter can be derived: As per 90.210(h), 90.691(a), the spurious emissions must be attenuated by 43 + 10log(P) which is: Therefore, the limit for spurious emissions is: At 3 meters measurement distance, the limit is; According to 24.238(a), all signals must be attenuated by 46.08 dB. Therefore, the limit for spurious emissions for a test distance of 3 meters is: FCC ID: L6GALR4600 Met 10023- 5 -November 20, 2000 6.1.4RESULTS: Frequency (MHz) Azimuth (Degrees) PolarityHeight (Meters) Raw Amplitude (dBuV) A.C.F. (dB)Cable loss (dB) Corrected Amplitude (dBuV/m) Limit dBm 127.34 360 H1.3620.113.3 2.1235.53 -23 127.34 60V125.34 13.972.1241.43 -23 56.38 328H1 .3614.9 11.31.3727.57 -23 56.38 0V1 13.4 10.4551.3725.23 -23 361.00 255H1 2…

Text truncated - open the document above for the full version.