LGYBT261159PRadio Bluetooth Unicellular

User's Guide OC-2 SERIES OF PRINTERS LP3.book Page 1 Wednesday, April 12, 2006 4:41 PM LP3.book Page 2 Wednesday, April 12, 2006 4:41 PM TA B L E O F C O N T E N T S OC-2 Printer Views 6 Front View 6 Back View 6 Right Side View 7 Left Side View 7 Setting Up Your Printer 8 Unpacking Your Printer 8 Installing Batteries 8 Removing Batteries9 Charging the Batteries9 Determining the Batteries' Condition 10 Loading Printable Media 11 Printing a Self-Test 13 Connecting the Printer 13 Installing a Data Cable13 Bluetooth and/or 802.11 b Parameters15 Configuring the Printer 15 Using the Belt Clip 16 Installing the Belt Clip 16 Removing the Belt Clip 16 Using the Control Panel 17 Audio Indicators 17 Battery Status LED 18 Power Button/LED 19 Media Function Button/LED 19 Radio Button/LED 20 Reset Button/LED 20 Using a CardReader 21 General Guidelines 21 LP3.book Page 3 Wednesday, April 12, 2006 4:41 PM TA B L E O F C O N T E N T S Using External Charging 22 Overview 22 Maintenance and Troubleshooting 23 Maintenance Guidelines 23 Preventative Maintenance 23 Troubleshooting 24 Help Desk 24 Supplies 25 For more information 25 LP3.book Page 4 Wednesday, April 12, 2006 4:41 PM LP3.book Page 5 Wednesday, April 12, 2006 4:41 PM OC-2 SERIES OF PRINTERS USER'S GUIDE 6 OC-2 Printer Views Front View Back View Figure X Figure X LP3.book Page 6 Wednesday, April 12, 2006 4:41 PM OC-2 PRINTER VIEWS 7 Right Side View Left Side View Figure X Figure X LP3.book Page 7 Wednesday, April 12, 2006 4:41 PM OC-2 SERIES OF PRINTERS USER'S GUIDE 8 Setting Up Your Printer Use the following information to set up your printer: •Unpacking Your Printer on page 8 •Installing Batteries on page 8 •Loading Printable Media on page 11 •Printing a Self-Test on page 13 •Connecting the Printer on page 13 •Configuring the Printer on page 15 In addition to the steps outlined in each section, additional information may be included if it applies to, or expands upon, the step being discussed. Unpacking Your Printer Before using the printer, remove all packaging material and inspect the printer for possible shipping damage. If the printer has been damaged: •Contact the shipping company and file a damage report. •Contact O’Neil Product Development, Inc. •Keep all shipping materials. Installing Batteries 1. Remove any packaging material (if applicable). 2. Position the battery with its contacts facing toward the battery cavity as shown in Figure X. Figure X Figure X LP3.book Page 8 Wednesday, April 12, 2006 4:41 PM SETTING UP YOUR PRINTER 9 3. Slide the battery into the battery cavity so that the edge of the battery hits the battery stop as shown in Figure X. The printer beeps one time when the first battery is installed. Do not force the battery into the battery cavity. When inserted properly, the battery easily slides and locks into place. If the battery does not easily slide into place, re- insert the battery. 4. Close the printer's cover. 5. Charge the batteries (batteries are shipped uncharged). For more information, see Charging the Batteries on page 9. Removing Batteries 1. Lift the battery up and out of the battery cavity while sliding it to the left (Figure X). 2. Remove the battery from the battery cavity. Charging the Batteries If the batteries are low when the printer turns on, the battery status LED displays red. For more information, see Using the Control Panel on page 17 . Perform the following procedure to charge the batteries: 1. Verify the battery is installed correctly. 2. Plug the AC adapter into the printer's power port (Figure X). Figure X LP3.book Page 9 Wednesday, April 12, 2006 4:41 PM OC-2 SERIES OF PRINTERS USER'S GUIDE 10 3. Plug the AC Adapter's power cord into an appropriate power source. 4. Charge the batteries. The Battery Status LED turns red while the batteries are charging and turns green when the batteries are fully charged. One complete charge takes 4 to 5 hours. Determining the Batteries' Condition The battery status LED displays the batteries' condition. When the battery status LED is solid red, the batteries must be charged; when solid orange, the batteries are at low power; when solid green, the batteries are charged. The batteries' voltage varies between 6.2 and 8.4 volts. For information on battery error conditions, see Using the Control Panel on page 17 . Power port Figure X Figure X LP3.book Page 10 Wednesday, April 12, 2006 4:41 PM SETTING UP YOUR PRINTER 11 Loading Printable Media Use the following procedure to load printable media: 1. Position the printer so that the O'Neil logo is facing you (Figure X). 2. Press and hold the printhead release button (Figure X). 3. Lift the printer's cover. 4. Place the paper roll between the metal paper roll holders as shown in Figure X. Make sure the paper exits “over” the roll and is firmly in place. 5. Unroll enough paper so that paper exits the printer (Figure X). Media Guidelines Media widthReceipt Paper: 2.25” Label Media: Roll capacity diameter Receipt Paper: 2.25” Label Media: Media typesReceipt paper media, thermal paper, hang tag stock. * Depending on the type of media used, you may need to configure your printer. For more information, see Configuring the Printer on page 15. Figure X Figure X LP3.book Page 11 Wednesday, April 12, 2006 4:41 PM OC-2 SERIES OF PRINTERS USER'S GUIDE 12 6. Close the printer's printhead cover. The printer's printhead cover “snaps” into place when completely closed. 7. Verify the media exits straight. 8. Push the Media Function button one time to advance the media (Figure X). 9. At either edge of the printer's printhead cover are serrated corners. Tear the media by pulling up and away from the printer's (Figure X). Warning: The tear bar and printhead cover's surface may be hot and/or sharp. Use caution when handling the printhead and tear bar. Figure X Figure X Figure X Figure X Figure X LP3.book Page 12 Wednesday, April 12, 2006 4:41 PM SETTING UP YOUR PRINTER 13 Printing a Self-Test 1. Press and hold the power button for approxi…

Text truncated - open the document above for the full version.

27 MF2T-L PRINTER USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is catuioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user's authority to operate this equipment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Applicable Directive •89/336/EEC, 73/23/EEC Applicable Standards •EN55022 (1998) •EN55024 (1998) •EN60950 (1992) Applicable Standards •TS001 •AN/NZS3260 LP3.book Page 27 Wednesday, April 12, 2006 4:41 PM

27 MF4T-L PRINTER USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is catuioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user's authority to operate this equipment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Applicable Directive •89/336/EEC, 73/23/EEC Applicable Standards •EN55022 (1998) •EN55024 (1998) •EN60950 (1992) Applicable Standards •TS001 •AN/NZS3260 LP3.book Page 27 Wednesday, April 12, 2006 4:41 PM

27 LP3 PRINTER USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is catuioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user's authority to operate this equipment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Applicable Directive •89/336/EEC, 73/23/EEC Applicable Standards •EN55022 (1998) •EN55024 (1998) •EN60950 (1992) Applicable Standards •TS001 •AN/NZS3260 LP3.book Page 27 Wednesday, April 12, 2006 4:41 PM

27 MF4T-L PRINTER USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is catuioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user's authority to operate this equipment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Applicable Directive •89/336/EEC, 73/23/EEC Applicable Standards •EN55022 (1998) •EN55024 (1998) •EN60950 (1992) Applicable Standards •TS001 •AN/NZS3260 LP3.book Page 27 Wednesday, April 12, 2006 4:41 PM 27 MF2T-L PRINTER USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is catuioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user's authority to operate this equipment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Applicable Directive •89/336/EEC, 73/23/EEC Applicable Standards •EN55022 (1998) •EN55024 (1998) •EN60950 (1992) Applicable Standards •TS001 •AN/NZS3260 LP3.book Page 27 Wednesday, April 12, 2006 4:41 PM 27 LP3 PRINTER USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is catuioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user's authority to operate this equipment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Applicable Directive •89/336/EEC, 73/23/EEC Applicable Standards •EN55022 (1998) •EN55024 (1998) •EN60950 (1992) Applicable Standards •TS001 •AN/NZS3260 LP3.book Page 27 Wednesday, April 12, 2006 4:41 PM 27 OC SERIES OF PRINTERS USER'S GUIDE Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been certified to comply with the limits for a Class B computing device, pursuant to FCC Rules. The user is catuioned that changes and modifi…

Text truncated - open the document above for the full version.

Subj:
Cellular Modems and Bluetooth
Date:
3/5/01 11:32:18 AM Pacific Standard Time
From: [email protected] (Frank Coperich) To: [email protected] CC: [email protected] (Joe Dichoso), [email protected] (Rich Fabina)
In response to your question(s) below: 3.) The Bluetooth approval procedures are listed below: BLUETOOTH APPROVALS For all devices, the following items, 1-12, are common to all Bluetooth devices and will not vary from one device to another. The list can be copied and pasted into the filing. 1 Output power and channel separation of a Bluetooth device in the different operating modes: The different operating modes (data-mode, acquisition-mode) of a Bluetooth device don*t influence the output power and the channel spacing. There is only one transmitter which is driven by identical input parameters concerning these two parameters. Only a different hopping sequence will be used. For this reason the check of these RF parameters in one op-mode is sufficient. 2 Frequency range of a Bluetooth device: Hereby we declare that the maximum frequency of this device is: 2402 * 2480 MHZ. This is according the Bluetooth Core Specification V 1.0B (+ critical errata) for devices which will be operated in the USA. This was checked during the Bluetooth Qualification tests (Test Case: TRM/CA/04-E). Other frequency ranges ( e.g. for Spain, France, Japan) which are allowed according the Core Specification are not supported by this device. 3 Co-ordination of the hopping sequence in data mode to avoid simultaneous occupancy by multiple transmitters: Bluetooth units which want to communicate with other units must be organized in a structure called piconet. This piconet consist of max. 8 Bluetooth units. One unit is the master the other seven are the slaves. The master co-ordinates frequency occupation in this piconet for all units. As the master hop sequence is derived from it*s BD address which is unique for every Bluetooth device, additional masters intending to establish new piconets will always use different hop sequences. 4 Example of a hopping sequence in data mode: Example of a 79 hopping sequence in data mode: 40, 21, 44, 23, 42, 53, 46, 55, 48, 33, 52, 35, 50, 65, 54, 67, 56, 37, 60, 39, 58, 69, 62, 71, 64, 25, 68, 27, 66, 57, 70, 59, 72, 29, 76, 31, 74, 61, 78, 63, 01, 41, 05, 43, 03, 73, 07, 75, 09, 45, 13, 47, 11, 77, 15, 00, 64, 49, 66, 53, 68, 02, 70, 06, 01, 51, 03, 55, 05, 04 5 Equally average use of frequencies in data mode and behavior for short transmissions: The generation of the hopping sequence in connection mode depends essentially on two input values: 1. LAP/UAP of the master of the connection 2. Internal master clock The LAP (lower address part) are the 24 LSB*s of the 48 BD_ADDRESS. The BD_ADDRESS is an unambiguous number of every Bluetooth unit. The UAP (upper address part) are the 24 MSB*s of the 48 BD_ADDRESS. The internal clock of a Bluetooth unit is derived from a free running clock which is never adjusted and is never turned off. For synchronization with other units only offset are used. It has no relation to the time of the day. Its resolution is at least half the RX/TX slot length of 312.5 μs. The clock has a cycle of about one day (23h30). In most case it is implemented as 28 bit counter. For the deriving of the hopping sequence the entire LAP (24 bits), 4 LSB*s (4 bits) (Input 1) and the 27 MSB*s of the clock (Input 2) are used. With this input values different mathematical procedures (permutations, additions, XOR-operations) are performed to generate the sequence. This will be done at the beginning of every new transmission. Regarding short transmissions the Bluetooth system has the following behavior: The first connection between the two devices is established, a hopping sequence was generated. For transmitting the wanted data the complete hopping sequence was not used. The connection ended. The second connection will be established. A new hopping sequence is generated. Due to the fact that the Bluetooth clock has a different value, because the period between the two transmission is longer (and it cannot be shorter) than the minimum resolution of the clock (312.5 μs). The hopping sequence will always differ from the first one. 6 Receiver input bandwidth and behavior for repeated single or multiple packets: The input bandwidth of the receiver is 1 MHZ. In every connection one Bluetooth device is the master and the other one is the slave. The master determines the hopping sequence (see chapter 5). The slave follows this sequence. Both devices shift between RX and TX time slot according to the clock of the master. Additionally the type of connection (e.g. single or multislot packet) is set up at the beginning of the connection. The master adapts its hopping frequency and its TX/RX timing according to the packet type of the connection. Also the slave of the connection will use these settings. Repeating of a packet has no influence on the hopping sequence. The hopping sequence generated by the master of the connection will be followed in any case. That means, a repeated packet will not be send on the same frequency, it is send on the next frequency of the hopping sequence 7 Dwell time in data mode The dwell time of 0.3797s within a 30 second period in data mode is independent from the packet type (packet length). The calculation for a 30 second period is a follows: Dwell time = time slot length * hop rate / number of hopping channels *30s Example for a DH1 packet (with a maximum length of one time slot) Dwell time = 625 μs * 1600 1/s / 79 * 30s = 0.3797s (in a 30s period) For multislot packet the hopping is reduced according to the length of the packet. Example for a DH5 packet (with a maximum length of five time slots) Dwell time = 5 * 625 μs * 1600 * 1/5 *1/s / 79 * 30s = 0.3797s (in a 30s period) This is according the Bluetooth Core Specification V 1.0B (+ critical errata) for all Bluetooth devices. Therefore all Bluetooth devices comply with the FCC dwell time require…

Text truncated - open the document above for the full version.

Scott McCutchan From: Scott McCutchan [[email protected]] Sent: Thursday, January 11, 2007 12:30 PM To: '[email protected]' Cc: '[email protected]'; '[email protected]' Subject: FCC ID: LGYBT261159P 1/11/2007 Mr. Fujimoto: In order for processing of this certification application (FCC ID: LGYBT261159P) to continue, the following issue(s) will have to be addressed: 1) The internal FCC label appears to be a paper stick-on label, which is not allowed under the rules. Please indicate the type of material of the label. 2) The authorization letter must be addressed to CETCB, and not the FCC in the text of the letter. 3) Please provide data showing compliance with voltage variation requirements of section 15.31(e) of the FCC rules. 4) The block diagram submitted is not sufficient. It must show the frequency of all oscillators in the device, and indicate the signal path and frequency at each block. 5) A user’s manual was submitted only for the OC2-L printer. Please submit the manual for each printer. 6) The certification contract on file is out of date. Please submit a signed copy of a current contract. The item(s) indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 60 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Please upload responses and/or exhibits to the electronic filing website. Your correspondence number is LGYBT261159-1. Best regards, Scott McCutchan Operations Manager Compatible Electronics TCB

Correspondence by Project Project Number: Correspondence NumberMemo LGYBT261159-1 1) The internal FCC label appears to be a paper stick-on label, which is not allowed under the rules. Please indicate the type of material of the label. Response: The label material is BradyID type LAT-29-747-10. See the attached webpage uploaded to the exhibits. It is made of polyester, and is printed with an indelible ink (laser printer toner.) 2) The authorization letter must be addressed to CETCB, and not the FCC in the text of the letter. Response: The authorization letter has been revised. 3) Please provide data showing compliance with voltage variation requirements of section 15.31(e) of the FCC rules. Response: The voltage variation requirements have been uploaded to the exhibits. 4) The block diagram submitted is not sufficient. It must show the frequency of all oscillators in the device, and indicate the signal path and frequency at each block. Response: The block diagram has been revised to show the frequency of all of the oscillators and indicate the signal path and frequency at each block. 5) A user’s manual was submitted only for the OC2-L printer. Please submit the manual for each printer. Response: The FCC statement from each printer manual will be on page 27. Let us know if you need the entire full manual for EACH printer. Please note that each printer manual is similar and that this statement will appear on page 27 of each version of the manual. 6) The certification contract on file is out of date. Please submit a signed copy of a current contract. Response: Ken Carlson should have fax you over the new certification contract to your location. 1166491128

LASERTAB Laser Printable Labels available from Bradyhttp://www.bradyid.com/bradyid/pdv/100770/BRADYID_US_LAT-2... 1 of 21/15/2007 3:41 PM WHAT'S NEW PRODUCTS BY CATEGORY PRODUCTS BY INDUSTRY SERVICES SUPPORT REGULATIONS/ COMPLIANCE PRODUCT REGISTRATION HomeProducts By CategoryLabelsPrintable LabelsCircuit Board & Component Labels LASERTAB® Laser Printable Labels Click for larger Image. OverviewSpecifications LASERTAB® Laser Printable Labels Blank, printable polyester labels for Laser Printers. This material is a UL recognized component and CSA accepted material when printed with designated laser printers. See UL file MH17154 and CSA Acceptance Record LS 41833 for specific details. Size: 0.650" W x 0.200" H (16.51 mm W x 5.08 mm H) Printable Area: 0.650" W x 0.200" H (16.51 mm W x 5.08 mm H) Label Type/Style: Label Color: White Finish: Matte Qty Per Row: 10 Qty Per Sheet: 480 Material Type: Polyester Brady Material #: B-747 Material Description: Permanent Polyester Adhesive: Acrylic Horizontal Repeat: 0.800" (20.32 mm) Top Margin: 0.875" (22.23 mm) Left Margin: 0.325" (8.26 mm) Application(s): Circuit Board & Component ID Through Hole Technology: Top: Yes. In extreme high temperatures, testing of this material is recommended, Bottom: No Surface Mount Technology: No, this material does not work with this application After Process: Yes, this material will work with this application Printer Compatibility: Laser Printers RoHS Compatibility: Compliant with RoHS Directive. NOTE: All statements concerning RoHS Directive compliance refer to 2005/618/EC MCV amendment to RoHS Directive 2002/95/EC. Product compliance is based upon information provided by suppliers of the raw materials used by Brady to manufacture these products, or by independent laboratory testing of these products. As such, Brady makes no independent representations or warranties, express or implied, and assumes no liability in connection with the use of this information. For more information on this product, contact Brady Customer Service or an Authorized Brady Distributor. Brady PRODUCT, FACILITY, & SAFETY IDENTIFICATION SOLUTIONS Home COUNTRY/REGION Select 6 Select About Brady ISO 9001 Contact Us Request A Catalog Find A Distributor Join Our Mailing List LASERTAB Laser Printable Labels available from Bradyhttp://www.bradyid.com/bradyid/pdv/100770/BRADYID_US_LAT-2... 2 of 21/15/2007 3:41 PM Copyright 2007 Brady Corporation products are sold through distribution. Click on the "Find a Distributor" button to find a distributor near you. *If you're not based in US, please contact your local Brady office for correct pricing. For Distributors: BradyDistributor.com | Bradyserve.com Additional Information: Privacy | Copyright | Site Map

LP3 Bluetooth Made in USA Part No. Serial No. LA00100 with FCC Standards FOR HOME OR OFFICE USE Tested to Comply 200270-100 Contains FCC ID: LGYBT261159P IC: 2640A-B261159P Contains radio device BT261159 Part No. Serial No. MF2T Bluetooth TA00100 with FCC Standards FOR HOME OR OFFICE USE Tested to Comply 200241-100 Contains FCC ID: LGYBT261159P IC: 2640A-B261159P Made in USA…

Text truncated - open the document above for the full version.