LGYWL430220Wireless Printer Module

User's Guide OC-2 SERIES OF PRINTERS LP3.book Page 1 Wednesday, April 12, 2006 4:41 PM LP3.book Page 2 Wednesday, April 12, 2006 4:41 PM TA B L E O F C O N T E N T S OC-2 Printer Views 6 Front View 6 Back View 6 Right Side View 7 Left Side View 7 Setting Up Your Printer 8 Unpacking Your Printer 8 Installing Batteries 8 Removing Batteries9 Charging the Batteries9 Determining the Batteries' Condition 10 Loading Printable Media 11 Printing a Self-Test 13 Connecting the Printer 13 Installing a Data Cable13 Bluetooth and/or 802.11 b Parameters15 Configuring the Printer 15 Using the Belt Clip 16 Installing the Belt Clip 16 Removing the Belt Clip 16 Using the Control Panel 17 Audio Indicators 17 Battery Status LED 18 Power Button/LED 19 Media Function Button/LED 19 Radio Button/LED 20 Reset Button/LED 20 Using a CardReader 21 General Guidelines 21 LP3.book Page 3 Wednesday, April 12, 2006 4:41 PM TA B L E O F C O N T E N T S Using External Charging 22 Overview 22 Maintenance and Troubleshooting 23 Maintenance Guidelines 23 Preventative Maintenance 23 Troubleshooting 24 Help Desk 24 Supplies 25 For more information 25 LP3.book Page 4 Wednesday, April 12, 2006 4:41 PM LP3.book Page 5 Wednesday, April 12, 2006 4:41 PM OC-2 SERIES OF PRINTERS USER'S GUIDE 6 OC-2 Printer Views Front View Back View Figure X Figure X LP3.book Page 6 Wednesday, April 12, 2006 4:41 PM OC-2 PRINTER VIEWS 7 Right Side View Left Side View Figure X Figure X LP3.book Page 7 Wednesday, April 12, 2006 4:41 PM OC-2 SERIES OF PRINTERS USER'S GUIDE 8 Setting Up Your Printer Use the following information to set up your printer: •Unpacking Your Printer on page 8 •Installing Batteries on page 8 •Loading Printable Media on page 11 •Printing a Self-Test on page 13 •Connecting the Printer on page 13 •Configuring the Printer on page 15 In addition to the steps outlined in each section, additional information may be included if it applies to, or expands upon, the step being discussed. Unpacking Your Printer Before using the printer, remove all packaging material and inspect the printer for possible shipping damage. If the printer has been damaged: •Contact the shipping company and file a damage report. •Contact O’Neil Product Development, Inc. •Keep all shipping materials. Installing Batteries 1. Remove any packaging material (if applicable). 2. Position the battery with its contacts facing toward the battery cavity as shown in Figure X. Figure X Figure X LP3.book Page 8 Wednesday, April 12, 2006 4:41 PM SETTING UP YOUR PRINTER 9 3. Slide the battery into the battery cavity so that the edge of the battery hits the battery stop as shown in Figure X. The printer beeps one time when the first battery is installed. Do not force the battery into the battery cavity. When inserted properly, the battery easily slides and locks into place. If the battery does not easily slide into place, re- insert the battery. 4. Close the printer's cover. 5. Charge the batteries (batteries are shipped uncharged). For more information, see Charging the Batteries on page 9. Removing Batteries 1. Lift the battery up and out of the battery cavity while sliding it to the left (Figure X). 2. Remove the battery from the battery cavity. Charging the Batteries If the batteries are low when the printer turns on, the battery status LED displays red. For more information, see Using the Control Panel on page 17 . Perform the following procedure to charge the batteries: 1. Verify the battery is installed correctly. 2. Plug the AC adapter into the printer's power port (Figure X). Figure X LP3.book Page 9 Wednesday, April 12, 2006 4:41 PM OC-2 SERIES OF PRINTERS USER'S GUIDE 10 3. Plug the AC Adapter's power cord into an appropriate power source. 4. Charge the batteries. The Battery Status LED turns red while the batteries are charging and turns green when the batteries are fully charged. One complete charge takes 4 to 5 hours. Determining the Batteries' Condition The battery status LED displays the batteries' condition. When the battery status LED is solid red, the batteries must be charged; when solid orange, the batteries are at low power; when solid green, the batteries are charged. The batteries' voltage varies between 6.2 and 8.4 volts. For information on battery error conditions, see Using the Control Panel on page 17 . Power port Figure X Figure X LP3.book Page 10 Wednesday, April 12, 2006 4:41 PM SETTING UP YOUR PRINTER 11 Loading Printable Media Use the following procedure to load printable media: 1. Position the printer so that the O'Neil logo is facing you (Figure X). 2. Press and hold the printhead release button (Figure X). 3. Lift the printer's cover. 4. Place the paper roll between the metal paper roll holders as shown in Figure X. Make sure the paper exits “over” the roll and is firmly in place. 5. Unroll enough paper so that paper exits the printer (Figure X). Media Guidelines Media widthReceipt Paper: 2.25” Label Media: Roll capacity diameter Receipt Paper: 2.25” Label Media: Media typesReceipt paper media, thermal paper, hang tag stock. * Depending on the type of media used, you may need to configure your printer. For more information, see Configuring the Printer on page 15. Figure X Figure X LP3.book Page 11 Wednesday, April 12, 2006 4:41 PM OC-2 SERIES OF PRINTERS USER'S GUIDE 12 6. Close the printer's printhead cover. The printer's printhead cover “snaps” into place when completely closed. 7. Verify the media exits straight. 8. Push the Media Function button one time to advance the media (Figure X). 9. At either edge of the printer's printhead cover are serrated corners. Tear the media by pulling up and away from the printer's (Figure X). Warning: The tear bar and printhead cover's surface may be hot and/or sharp. Use caution when handling the printhead and tear bar. Figure X Figure X Figure X Figure X Figure X LP3.book Page 12 Wednesday, April 12, 2006 4:41 PM SETTING UP YOUR PRINTER 13 Printing a Self-Test 1. Press and hold the power button for approxi…

Text truncated - open the document above for the full version.

114 OLINDA DRIVE • •• • BREA, CALIFORNIA 92823 • •• • (714) 579-0500 • •• • FAX (714) 579-1850 March 24, 2010 ATCB 6731 Whittier Ave. McLean, VA 22101 Subject: Request for Certification of the Datamax / O’Neil SDABG1, Model: WL430220 for FCC and Industry Canada FCC ID: LGYWL430220 IC: 2640A-WL430220 Gentlemen: We have enclosed a package for the certification to FCC and Industry Canada for the Datamax / O’Neil SDABG1 Model: WL430220. We are requesting a limited modular approval for the EUT. The limited modular approval will cover the use of the EUT in five different Datamax / O’Neil printers. The model numbers of those printers are: LP3-L, MF2t-L, MF4t-L, OC2, and OC3. The 2412 MHz to 2462 MHz band for both 802.11 b and 802.11 g will be for all five printers. The 5745 MHz to 5825 MHz band for part of the 802.11 a band will only be for the LP3-L printer. We have enclosed the completed Form 731 and Industry Canada Application Form with the applicable exhibits. If you have any questions or need any additional information, please give me a call at (714) 579-0500. Sincerely, Kyle Fujimoto Test Engineer

Doug Noble From: Kyle Fujimoto [[email protected]] Sent: Wednesday, September 15, 2010 4:38 PM To: Doug Noble Subject: Fwd: Regarding the LGYWL430220 Page 1 of 3 9/16/2010 Doug, I had asked the FCC (see forward E-mail below) if it is was OK to just get the 5745 MHz to 5825 MHz bands for the 802.11 a bands approved and get the rest done at a later time has a class II permissive change. The FCC said this was OK and Marianne said it would be OK for IC. The cover letter also states that the 5745 MHz to 5825 MHz band will only be approved for the LP3-L (under the limited modular approval) at this time. This means there will be no UNII certification involved here. The official FCC responses is under tracking number: 344797. Regards, Kyle Fujimoto Test Engineer -- Compatible Electronics, Inc. -- Brea Division Phone:(714) 579-0500 Fax: (714) 579-1850 [email protected] http://www.celectronics.com -----Original Message----- From: Marianne Bosley <[email protected]> To: 'Kyle Fujimoto' <[email protected]> Date: Tue, 9 Mar 2010 21:13:49 -0500 Subject: FW: Question Regarding 802.11 a/b/g/Module (Fwd: Response to Inquiry to FCC (Tracking Number 344797)) Hi Kyle, It should be fine for IC. Marianne Marianne Bosley Customer Development Representative AmericanTCB Inc. Certification Resource for the Wireless Industry www.atcb.com Business: (703)847-4700 Direct: (717)676-3203 This message is intended only for the use of the individual or entity to which it is addressed and may contain information that is confidential and exempt from disclosure under applicable law. Cc: Marianne Bosley Sent: Monday, March 08, 2010 2:57 PM To: Marianne Bosley Subject: Question Regarding 802.11 a/b/g/Module (Fwd: Response to Inquiry to FCC (Tracking Number 344797)) Marianne, Can you please see if the follow below regarding an 802.11 a/b/g module is also acceptable for Industry Canada. We just got a response from the FCC today (Tracking Number 344797) that the below is acceptable and a class II permissive change can be done later for the UNII portions.: Inquiry: We are currently testing an 802.11 a/b/g module (EUT) for a limited modular approval. This limited modular approval will be used to covered the usage of the module in select printers that the EUT goes into. Can we just test the 802.11 b/g and the 5745 MHz to 5825 MHz bands of the 802.11 a portion right now and get that approved for certification and then come back later to do the 5150-5350 MHz and 5470 MHz to 5725 MHz bands for the 802.11 a portion later and cover that under the same FCC ID via a class II permissive change? There would be no changes to the actual 802.11 a/b/g module at all. The reason for this is that we are assessing an A version for a future launch. The end user will not be able to access the 802.11a at this time. Response: Yes this is acceptable Regards, Kyle Fujimoto Test Engineer -- Compatible Electronics, Inc. -- Brea Division Phone:(714) 579-0500 Fax: (714) 579-1850 [email protected] http://www.celectronics.com -----Original Message----- From: [email protected] To: [email protected] Date: Mon, 8 Mar 2010 14:42:07 -0500 (EST) Subject: Response to Inquiry to FCC (Tracking Number 344797) Inquiry: We are currently testing an 802.11 a/b/g module (EUT) for a limited modular approval. This limited modular approval will be used to covered the usage of the module in select printers that the EUT goes into. Can we just test the 802.11 b/g and the 5745 MHz to 5825 MHz bands of the 802.11 a portion right now and get that approved for certification and then come back later to do the 5150-5350 MHz and 5470 MHz to 5725 MHz bands for the 802.11 a portion later and cover that under the same FCC ID via a class II permissive change? There would be no changes to the actual 802.11 a/b/g module at all. The reason for this is that we are assessing an A version for a future launch. The end user will not be able to access the 802.11a at this time. FCC Home| Search| RSS| Updates| E-Filing| Initiatives | Consumers| Find People Office of Engineering and Technology Page 2 of 3 9/16/2010 Response: Yes this is acceptable Do not reply to this message. Please select the Reply to an Inquiry Response link from the OET Inquiry System to add any additional information pertaining to this inquiry. Page 3 of 3 9/16/2010

FCC ID: LGYWL430220 IC: 2640A-WL430220 Made in Japan Fabriqué au Japon 0017AC XXXXXX SDABG1WL430220

ANTENNA INFORMATION The antenna LEG-B has a gain of 3 dBi The antenna LEG-C2 has a gain of 2.4 dBi The antenna LEG-E has a gain of 0 dBi

© 2010 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 2867 Progress Place, Suite 4D • Escondido, CA 92029 • U.S.A. TEL (760) 737-3131 • FAX (760) 737-9131 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION O’Neil Product Development, Inc. Dates of Test: March 18, 2010 8 Mason Test Report Number: SAR.20100311 Irvine, CA 92618 This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1999 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2003, OET Bulletin 65 Supp. C, RSS-102 and Safety Code 6 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Certificate # 2387.01 FCC ID: LGYWL430220 IC Certificate: 2640-WL430220 Model(s): LP3 802.11 Test Sample: Production Unit Serial No.: LA08576 Equipment Type: Wireless Printer Classification: Portable Transmitter Next to Body TX Frequency Range: 2412 – 2462 MHz; 5180 – 5320 MHz; 5745 – 5825 MHz Frequency Tolerance: ± 25 ppm Maximum RF Output: 2.4 MHz, (b)19.90 dBm, (g)20.13 dBm; 5.2 GHz 21.35 dBm; 5.8 GHz 20.35 dBm Conducted Signal Modulation: DSSS, OFDM Antenna Type (Length): Internal(O’Neil Pro. Dev., P/N LP3) Battery: Std. (Totex P/N 550039-100) Battery Pack Application Type: Certification FCC Rule Parts: Part 15C, Sec. 15.247 Industry Canada: RSS-102, Safety Code 6 FCC ID: LGYWL430220 © 2010 RF Exposure Lab, LLC Page 2 of 156 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Table of Contents 1. Introduction ...........................................................................................................................3 SAR Definition [5]......................................................................................................................3 2. SAR Measurement Setup .....................................................................................................4 Robotic System .........................................................................................................................4 System Hardware .....................................................................................................................4 System Description ...................................................................................................................4 E-Field Probe ALS-E-020 ......................................................................................................... 5 3. Robot Specifications .............................................................................................................7 4. Probe and Dipole Calibration ................................................................................................8 5. Phantom & Simulating Tissue Specifications........................................................................9 SAM Phantom ...........................................................................................................................9 Brain & Muscle Simulating Mixture Characterization ................................................................9 Device Holder ...........................................................................................................................9 6. Definition of Reference Points.............................................................................................10 Ear Reference Point................................................................................................................10 Device Reference Points ........................................................................................................10 7. Test Configuration Positions ...............................................................................................11 Positioning for Cheek/Touch [5] ..............................................................................................11 Positioning for Ear / 15 ̊ Tilt [5] ................................................................................................12 Body Worn Configurations ......................................................................................................13 8. ANSI/IEEE C95.1 – 1999 RF Exposure Limits [2]...............................................................14 Uncontrolled Environment.......................................................................................................14 Controlled Environment .......................................................................................................... 14 9. Measurement Uncertainty ...................................................................................................15 10. System Validation ........................................................................................................... 16 Tissue Verification...................................................................................................................16 Test System Verification .........................................................................................................16 11. SAR Test Data Summary ................................................................................................17 Procedures Used To Establish Test Signal.............................................................................17 Device Test Condition ...........…

Text truncated - open the document above for the full version.

© 2010 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 2867 Progress Place, Suite 4D • Escondido, CA 92029 • U.S.A. TEL (760) 737-3131 • FAX (760) 737-9131 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION O’Neil Product Development, Inc. Dates of Test: March 18, 2010 8 Mason Test Report Number: SAR.20100305 Irvine, CA 92618 This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1999 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2003, OET Bulletin 65 Supp. C, RSS-102 and Safety Code 6 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Certificate # 2387.01 FCC ID: LGYWL430220 IC Certificate: 2640-WL430220 Model(s): MF2T 802.11 Test Sample: Production Unit Serial No.: TA04187 Equipment Type: Wireless Printer Classification: Portable Transmitter Next to Body TX Frequency Range: 2412 – 2462 MHz Frequency Tolerance: ± 25 ppm Maximum RF Output: 2412–2462 MHz, (b)19.90 dBm, (g)20.13 dBm Conducted Signal Modulation: DSSS, OFDM Antenna Type (Length): Internal(O’Neil Pro. Dev., P/N MF2T) Battery: Std. (Totex P/N 550041-100) Battery Pack Application Type: Certification FCC Rule Parts: Part 15C, Sec. 15.247 Industry Canada: RSS-102, Safety Code 6 FCC ID: LGYWL430220 © 2010 RF Exposure Lab, LLC Page 2 of 59 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Table of Contents 1. Introduction ...........................................................................................................................3 SAR Definition [5]......................................................................................................................3 2. SAR Measurement Setup .....................................................................................................4 Robotic System .........................................................................................................................4 System Hardware .....................................................................................................................4 System Description ...................................................................................................................4 E-Field Probe ALS-E-020 ......................................................................................................... 5 3. Robot Specifications .............................................................................................................7 4. Probe and Dipole Calibration ................................................................................................8 5. Phantom & Simulating Tissue Specifications........................................................................9 SAM Phantom ...........................................................................................................................9 Brain & Muscle Simulating Mixture Characterization ................................................................9 Device Holder ...........................................................................................................................9 6. Definition of Reference Points.............................................................................................10 Ear Reference Point................................................................................................................10 Device Reference Points ........................................................................................................10 7. Test Configuration Positions ...............................................................................................11 Positioning for Cheek/Touch [5] ..............................................................................................11 Positioning for Ear / 15 ̊ Tilt [5] ................................................................................................12 Body Worn Configurations ......................................................................................................13 8. ANSI/IEEE C95.1 – 1999 RF Exposure Limits [2]...............................................................14 Uncontrolled Environment.......................................................................................................14 Controlled Environment .......................................................................................................... 14 9. Measurement Uncertainty ...................................................................................................15 10. System Validation ........................................................................................................... 16 Tissue Verification...................................................................................................................16 Test System Verification .........................................................................................................16 11. SAR Test Data Summary ................................................................................................17 Procedures Used To Establish Test Signal.............................................................................17 Device Test Condition ............................................................................…

Text truncated - open the document above for the full version.

© 2010 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 2867 Progress Place, Suite 4D • Escondido, CA 92029 • U.S.A. TEL (760) 737-3131 • FAX (760) 737-9131 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION O’Neil Product Development, Inc. Dates of Test: March 18, 2010 8 Mason Test Report Number: SAR.20100307 Irvine, CA 92618 This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1999 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2003, OET Bulletin 65 Supp. C, RSS-102 and Safety Code 6 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Certificate # 2387.01 FCC ID: LGYWL430220 IC Certificate: 2640-WL430220 Model(s): MF4T 802.11 Test Sample: Production Unit Serial No.: MP19804 Equipment Type: Wireless Printer Classification: Portable Transmitter Next to Body TX Frequency Range: 2412 – 2462 MHz Frequency Tolerance: ± 25 ppm Maximum RF Output: 2412–2462 MHz, (b)19.90 dBm, (g)20.13 dBm Conducted Signal Modulation: DSSS, OFDM Antenna Type (Length): Internal(O’Neil Pro. Dev., P/N MF4T) Battery: Std. (Totex P/N 550039-100) Battery Pack Application Type: Certification FCC Rule Parts: Part 15C, Sec. 15.247 Industry Canada: RSS-102, Safety Code 6 FCC ID: LGYWL430220 © 2010 RF Exposure Lab, LLC Page 2 of 59 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Table of Contents 1. Introduction ...........................................................................................................................3 SAR Definition [5]......................................................................................................................3 2. SAR Measurement Setup .....................................................................................................4 Robotic System .........................................................................................................................4 System Hardware .....................................................................................................................4 System Description ...................................................................................................................4 E-Field Probe ALS-E-020 ......................................................................................................... 5 3. Robot Specifications .............................................................................................................7 4. Probe and Dipole Calibration ................................................................................................8 5. Phantom & Simulating Tissue Specifications........................................................................9 SAM Phantom ...........................................................................................................................9 Brain & Muscle Simulating Mixture Characterization ................................................................9 Device Holder ...........................................................................................................................9 6. Definition of Reference Points.............................................................................................10 Ear Reference Point................................................................................................................10 Device Reference Points ........................................................................................................10 7. Test Configuration Positions ...............................................................................................11 Positioning for Cheek/Touch [5] ..............................................................................................11 Positioning for Ear / 15 ̊ Tilt [5] ................................................................................................12 Body Worn Configurations ......................................................................................................13 8. ANSI/IEEE C95.1 – 1999 RF Exposure Limits [2]...............................................................14 Uncontrolled Environment.......................................................................................................14 Controlled Environment .......................................................................................................... 14 9. Measurement Uncertainty ...................................................................................................15 10. System Validation ........................................................................................................... 16 Tissue Verification...................................................................................................................16 Test System Verification .........................................................................................................16 11. SAR Test Data Summary ................................................................................................17 Procedures Used To Establish Test Signal.............................................................................17 Device Test Condition ............................................................................…

Text truncated - open the document above for the full version.

© 2010 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 2867 Progress Place, Suite 4D • Escondido, CA 92029 • U.S.A. TEL (760) 737-3131 • FAX (760) 737-9131 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION O’Neil Product Develo…

Text truncated - open the document above for the full version.