LNQ802RUN2Wireless Dual-Band USB Module

W725D0 802.11ABGN 2T2R USB Module Page 1 of 12 Product Specification Model Name: W725D0 Part No.: WW725D0566A20H IEEE 802.11ABGN 2T2R USB Module Version: 1.1 Date: June. 5. 2013 W725D0 802.11ABGN 2T2R USB Module Page 2 of 12 Release History DATE REV Description of Change 2012/07/30 0.1 Preliminary specification release 2012/10/02 0.2 Add power consumption 2012/10/04 0.3 Update block diagram 2012/10/13 0.4 Update dimension and power consumption 2012/11/15 1.0 Change model name to W725D0, update RF Spec. 2013/5/7 1.0 Customized for Actiontec 2013/6/5 1.1 Delete dual MAC description and Modify FCC Label W725D0 802.11ABGN 2T2R USB Module Page 3 of 12 W725D0 IEEE 802.11ABGN 2T2 USB Module 1 Product Features  Supports 2T2R 2.4/5GHz dual-band  Maximum PHY data rate up to 144.4 Mbps using 20MHz bandwidth, 300Mbps using 40MHz bandwidth  Short Guard Interval (400ns)  Sounding packet  Host interface complies with USB Specification Revision 2.0  Supports IEEE 802.11 e/ i/ h/ k  WAPI (Wireless Authentication Pivacy Infrastructure) cerified  Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU)  Low latency immediate High-Throughput Block Acknowledgement (HT-BA)  Long NAV for media reservation with CF-End for NAV release  PHY-level spoofing to enhance legacy compatibility  MIMO power saving mechanism  Channel management and co-existence  Supports Wake-On-WLAN via Magic Packet and Wake-up frame  Transmit Opportunity (TXOP) Short Inter-Frame Space (SIFS) bursting for higher multimedia bandwidth  WiFi Direct supports wireless peer to peer applications. W725D0 802.11ABGN 2T2R USB Module Page 4 of 12 2 Block Diagram W725D0 802.11ABGN 2T2R USB Module Page 5 of 12 3 General Specification   Module Name  W725D0  Product Specification  WLAN Standard IEEE 802.11a/b/g/n  Host Interface USB 2.0  Host Connector Options 4 pins header type connector  Major Chipset Realtek RTL8192DU  Dimensions (board size)  Minimum Typical Maximum Unit Length 60.2 60.5 60.8 mm  Width 22.4 22.6 22.8 mm  Height 2.9 3.1 3.3 mm  Weight 6.8 7 7.2 g  Antenna Connector Options 2 printed PCB antennas on board  Operating Condition  Minimum Typical Maximum Unit  Voltage DC 4.74 5 5.25 V  Temperature 0 70 °C  Storage temperature -20 70 °C  Humidity Non-Operating 10 80 %  Electrical Specification  Frequency Range 2400 ~ 2483 MHz; 5150 ~ 5825 MHz  Band Width 20MHz/ 40MHz Mixed mode 2.4GHz Band  Output power  Minimum Typical Maximum Unit 802.11b 15 17 19 dBm 802.11g 54Mbps 9 11 13 dBm 802.11n/ HT20 MCS7 7 9 11 dBm 802.11n/ HT40 MCS7 7 9 11 dBm  Receiver Sensitivity  Minimum Typical Maximum Unit 802.11b11Mbps -80 dBm 802.11g 54Mbps -65 dBm 802.11n/ HT20 MCS7 -64 dBm W725D0 802.11ABGN 2T2R USB Module Page 6 of 12 802.11n/ HT40 MCS7 -61 dBm 5GHz Band  Output power  Minimum Typical Maximum Unit 802.11a 54Mbps 8 10 12 dBm 802.11n/ HT20 MCS7 Lower/ Middle Band 7 9 11 dBm 802.11n/ HT20 MCS7 Upper Band 5 7 9 dBm 802.11n/ HT40 MCS7 Lower/ Middle Band 7 9 11 dBm 802.11n/ HT40 MCS7 Upper Band 5 7 9 dBm  Receiver Sensitivit y  Minimum Typical Maximum Unit 802.11a 54Mbps -65 dBm 802.11n/ HT20 MCS7 -64 dBm 802.11n/ HT40 MCS7 -61 dBm 4 Mechanical Dimension W725D0 802.11ABGN 2T2R USB Module Page 7 of 12 5 Power Consumption Test condition OS：Windows XP Channel 6：2437MHz Standard：IEEE802.11B,G.N Input voltage for whole circuit：4.97V TX uses continuous mode Test tool MP_Kit_RTL11n_DualMAC_9xD_USB_v019_20120307 5.1 Test result： Continuous TX/RX @ 2.4GHz Mode Standard Current (mA) mA DAC TX 1M 391 41 11M 238 41 6M 384 52 54M 384 52 HT20-MCS0 373 48 HT20-MCS7 373 48 HT40-MCS0 370 48 HT40-MCS7 371 48 RX 1M 249 41 11M 249 41 6M 243 52 54M 243 52 HT20-MCS0 245 48 HT20-MCS7 245 48 HT40-MCS0 245 48 HT40-MCS7 245 48 W725D0 802.11ABGN 2T2R USB Module Page 8 of 12 Test condition OS：Windows XP Channel 165：5825MHz Standard：IEEE802.11A, AN Input voltage for whole circuit：4.97V TX uses continuous mode 5.2 Test result： MP_Kit_RTL11n_DualMAC_9xD_USB_v019_20120307 Continuous TX/RX @ 5GHz Mode Standard Current (mA) mA DAC TX 6M 377 46 54M 378 46 HT20-MCS0 369 42 HT20-MCS7 369 42 HT40-MCS0 395 42 HT40-MCS7 394 45 RX 6M 242 46 54M 241 46 HT20-MCS0 241 42 HT20-MCS7 243 42 HT40-MCS0 244 45 HT40-MCS7 244 45 W725D0 802.11ABGN 2T2R USB Module Page 9 of 12 Test condition OS：Windows XP Channel 6：2437MHz Standard：IEEE802.11G,N RF output connects with AP (D-Link DIR-635, 2T3R) Input voltage for whole circuit：4.97V Throughput test mode Distance Limit: 1M (Signal & Quality 100%) Test driver Realtek, RTL8192DU_Drv_1016.1.0413.2012_UI_1.00.0180.All_In_One_Driver_Merge d_UI.L 5.3 Test result：Throughput test @2.4GHz Mode Standard Current (mA) Min Max TX 54M 197 210 HT20-MCS7 380 411 HT40-MCS7 275 382 RX 54M 194 198 HT20-MCS7 186 201 HT40-MCS7 197 205 Uninstall Driver 20 Idle (Non Connect) 178 Idle (associated) 183 Driver disable 126 W725D0 802.11ABGN 2T2R USB Module Page 10 of 12 Test condition OS：Windows XP Channel 165：5825MHz Standard：IEEE802.11A,N RF output connects with AP (D-Link DIR-635, 2T3R) Input voltage for whole circuit: 4.97V Throughput test mode Distance Limit: 1M (Signal & Quality 100%) Test driver Realtek, RTL8192DU_Drv_1016.1.0413.2012_UI_1.00.0180.All_In_One_Driver_Merge d_UI.L 8.4 Test result：Throughput test @5GHz Mode Standard Current (mA) Min Max TX 54M 313 323 HT20-MCS7 332 356 HT40-MCS7 320 367 RX 54M 271 281 HT20-MCS7 240 278 HT40-MCS7 243 276 Uninstall Driver 21 Idle (Non Connect) 168 Idle (associated) 245 Driver disable 140 W725D0 802.11ABGN 2T2R USB Module Page 12 of 12 10. Package 2006/8/16 v1.0 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used…

Text truncated - open the document above for the full version.

Actiontec Electronics, Inc. 760 North Mary Avenue • Sunnyvale • CA • 94085 • USA Phone (408) 752-7700 • Fax (408) 541-9003 • www.actiontec.com Solutions for the Digital Life™ DECLARATION LETTER Date: May 29, 2013 FCC ID: LNQ802RUN2 To whom it may concern: We, Actiontec Electronics, Inc. declares that the device does not have “Ad Hoc on non-US frequencies” and/or “on DFS frequencies” while applying for the following product. If you have any questions regarding the authorization, please do not hesitate to contact us. Thank you! Sincerely, Angela Yao/Sr. Program Manager Phone: (408) 752-7700 Fax: (408) 541-9003 Email: [email protected]

Actiontec Electronics, Inc. 760 North Mary Avenue • Sunnyvale • CA • 94085 • USA Phone (408) 752-7700 • Fax (408) 541-9003 • www.actiontec.com Solutions for the Digital Life™ Date: May 29, 2013 FCC ID: LNQ802RUN2 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to DA 04-1705 of the commission’s public notice, we request short-term confidential treatment for the following information until 180 days in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely, Angela Yao/Sr. Program Manager Phone: (408) 752-7700 Fax: (408) 541-9003 Email: [email protected]

Actiontec Electronics, Inc. 760 North Mary Avenue • Sunnyvale • CA • 94085 • USA Phone (408) 752-7700 • Fax (408) 541-9003 • www.actiontec.com Solutions for the Digital Life™ Date: May 29, 2013 FCC ID: LNQ802RUN2 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Angela Yao/Sr. Program Manager Phone: (408) 752-7700 Fax: (408) 541-9003 Email: [email protected]

Actiontec Electronics, Inc. 760 North Mary Avenue • Sunnyvale • CA • 94085 • USA Phone (408) 752-7700 • Fax (408) 541-9003 • www.actiontec.com Solutions for the Digital Life™ Date: May 29, 2013 AGENCY AUTHORIZATION LETTER We, the undersigned Actiontec Electronics, Inc. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC Part 15 and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely, Angela Yao/Sr. Program Manager Phone: (408) 752-7700 Fax: (408) 541-9003 Email: [email protected]

FCC ID: LNQ802RUN2 Report No.: RF 130502C19 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch June 3, 2013 Dear Application Examiner, Actiontec Electronics,Inc., FCC ID: LNQ802RUN2 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip RTL8192DU. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is RTL8192DU. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: LNQ802RUN2 Report No.: RF 130502C19 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

1 F 2 3 4 5 k n a r F E D C D T L , . o C S C I N O R T C E L E Y N O C I H C F 6 7 8 D E C L O B M Y S . V E R B A 1 2 3 4 5 A B A B 7 6 N O I T P I R C S E D E T A D 8 D E V O R P P A N G I S ) : s e t o N r e p a P e e r f d o o W : l a i r e t e M . 1 K B : r o l o C g n i t n i r P . 2 m m 41 x 02: e z i S . 3 m m : t i n U . 4 : s r e h t O . 5 Bottom view FCC ID: LNQ802RUN2. Model: 802RUN2 MAC ID: XX:XX:XX:XX:XX:XX ||||||||||||||||||||||| 1.0A Made in China FCC ID: LNQ802RUN 2 Model: 802RUN2 MAC ID: XX:XX:XX:XX:XX:XX ||||||||||||||||||||||| 1.0A Made in China

FCC ID: LNQ802RUN2 Model: 802RUN2 MAC ID: XX:XX:XX:XX:XX:XX ||||||||||||||||||||||| 1.0A Made in China MAC ID+ IC : 2496A-802RUN2

Page 2

FCC ID: LNQ802RUN2 Report No.: RF130502C19 Operational Description This device is a Wireless Dual-Band USB Module, which operates in both 2.4GHz and 5GHz bands; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 3.3Vdc by host equipment. The antenna is Printed antenna without antenna connector. The other instruction, please have a look at the users manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA130502C19 1 of 5 Report Format Version 5.1.0 RF EXPOSURE REPORT REPORT NO.: SA130502C19 MODEL NO.: 802RUN2 FCC ID: LNQ802RUN2 RECEIVED: May 02, 2013 TESTED: May 07 ~ May 11, 2013 ISSUED: May 27, 2013 APPLICANT: Actiontec Electronics, Inc. ADDRESS: 760 North Mary Ave. Sunyvale, CA 94085 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA130502C19 2 of 5 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 3 1. CERTIFICATION ....................................................................................................................... 4 2. RF EXPOSURE ........................................................................................................................ 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) .................................................. 5 2.2 MPE CALCULATION FORMULA .............................................................................................. 5 2.3 CLASSIFICATION ..................................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................................... 5 Report No.: SA130502C19 3 of 5 Report Format Version 5.1.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130502C19 Original release May 27, 2013 Report No.: SA130502C19 4 of 5 Report Format Version 5.1.0 1. CERTIFICATION PRODUCT: Wireless Dual-Band USB Module MODEL NO.: 802RUN2 BRAND: Actiontec APPLICANT: Actiontec Electronics, Inc. TESTED: May 07 ~ May 11, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: 802RUN2) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :May 27, 2013 Pettie Chen / Senior Specialist APPROVED BY: , DATE :May 27, 2013 Ken Liu / Senior Manager Report No.: SA130502C19 5 of 5 Report Format Version 5.1.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER Frequency band (MHz) Conducted power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) 2412~2462 27.74 6.61 20 0.542 1 5180~5240 16.54 6.21 20 0.037 1 5745~5825 25.02 6.21 20 0.264 1 Note: 2.4GHz: Directional gain = 3.6dBi + 10log(2) = 6.61dBi 5.0GHz: Directional gain = 3.2dBi + 10log(2) = 6.21dBi

Report No.: RF130502C19 1 of 81 Report Format Version 5.1.0 FCC TEST REPORT (15.247) REPORT NO.: RF130502C19 MODEL NO.: 802RUN2 FCC ID: LNQ802RUN2 RECEIVED: May 02, 2013 TESTED: May 07 ~ May 11, 2013 ISSUED: May 27, 2013 APPLICANT: Actiontec Electronics, Inc. ADDRESS: 760 North Mary Ave. Sunyvale, CA 94085 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130502C19 2 of 81 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .......................................................................................... 5 1. CERTIFICATION ................................................................................................ 6 2. SUMMARY OF TEST RESULTS ....................................................................... 7 2.1 MEASUREMENT UNCERTAINTY ..................................................................... 7 3. GENERAL INFORMATION ................................................................................ 8 3.1 GENERAL DESCRIPTION OF EUT .................................................................. 8 3.2 DESCRIPTION OF TEST MODES .................................................................... 9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................. 10 3.3 DESCRIPTION OF SUPPORT UNITS ............................................................ 14 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................. 14 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 14 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ...................................... 15 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .......................... 15 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ....... 15 4.1.2 TEST INSTRUMENTS ..................................................................................... 16 4.1.3 TEST PROCEDURES ..................................................................................... 17 4.1.4 DEVIATION FROM TEST STANDARD ............................................................ 17 4.1.5 TEST SETUP ................................................................................................... 18 4.1.6 EUT OPERATING CONDITIONS .................................................................... 18 4.1.7 TEST RESULTS .............................................................................................. 19 4.2 CONDUCTED EMISSION MEASUREMENT .................................................. 32 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ................................ 32 4.2.2 TEST INSTRUMENTS ..................................................................................... 32 4.2.3 TEST PROCEDURES ..................................................................................... 33 4.2.4 DEVIATION FROM TEST STANDARD ............................................................ 33 4.2.5 TEST SETUP ................................................................................................... 33 4.2.6 EUT OPERATING CONDITIONS .................................................................... 33 4.2.7 TEST RESULTS .............................................................................................. 34 4.3 6dB BANDWIDTH MEASUREMENT ............................................................... 36 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ............................................ 36 4.3.2 TEST SETUP ................................................................................................... 36 4.3.3 TEST INSTRUMENTS ..................................................................................... 36 4.3.4 TEST PROCEDURE ........................................................................................ 36 4.3.5 DEVIATION FROM TEST STANDARD ............................................................ 36 4.3.6 EUT OPERATING CONDITIONS .................................................................... 36 4.3.7 TEST RESULTS .............................................................................................. 37 4.4 CONDUCTED OUTPUT POWER .................................................................... 38 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT .................... 38 4.4.2 TEST SETUP .......................................................................…

Text truncated - open the document above for the full version.

Report No.: RF130502C19-1 1 of 44 Report Format Version 5.1.0 FCC TEST REPORT (15.407) REPORT NO.: RF130502C19-1 MODEL NO.: 802RUN2 FCC ID: LNQ802RUN2 RECEIVED: May 02, 2013 TESTED: May 07 ~ May 11, 2013 ISSUED: May 27, 2013 APPLICANT: Actiontec Electronics, Inc. ADDRESS: 760 North Mary Ave. Sunyvale, CA 94085 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130502C19-1 2 of 44 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................. 4 1. CERTIFICATION ...................................................................................................... 5 2. SUMMARY OF TEST RESULTS.............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 6 3. GENERAL INFORMATION ...................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................ 7 3.2 DESCRIPTION OF TEST MODES .......................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .......................... 9 3.3 DUTY CYCLE OF TEST SIGNAL .......................................................................... 11 3.4 DESCRIPTION OF SUPPORT UNITS ................................................................... 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 12 4. TEST TYPES AND RESULTS ................................................................................ 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 13 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS ......... 13 4.1.3 TEST INSTRUMENTS ........................................................................................... 14 4.1.4 TEST PROCEDURES ............................................................................................ 15 4.1.5 DEVIATION FROM TEST STANDARD .................................................................. 15 4.1.6 TEST SETUP ......................................................................................................... 16 4.1.7 EUT OPERATING CONDITION ............................................................................. 16 4.1.8 TEST RESULTS ..................................................................................................... 17 4.2 CONDUCTED EMISSION MEASUREMENT ......................................................... 26 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 26 4.2.2 TEST INSTRUMENTS ........................................................................................... 26 4.2.3 TEST PROCEDURES ............................................................................................ 27 4.2.4 DEVIATION FROM TEST STANDARD .............…

Text truncated - open the document above for the full version.