M8C-TP36RF433-152Remote control transmitter

1 2 3 OPERATIING INSTRUCTIONS 2. Open the battery cover. 3. To make fan operational, install two 1.5V AAA batteries (included). Replace the battery cover. NOTE: This remote control uses two 1.5V AAA batteries. Replace batteries with the correct size and type of battery. Clean the battery contacts and area inside the device prior to installing new batteries. Ensure the batteries are installed correctly with regard to the polarity ( + and -). NOTE: If not used for long periods of time, remove battery to prevent damage to transmitter. Store the remote control away from excessive heat and humidity. 1. Slide the transmitter out of the transmitter holder. Select a location to install your transmitter holder. Attach the transmitter holder with screws provided. ON ECE 1 2 3 4 5 ON ECE 12345 OFF HI MED LO 1 TP36RF433-152 MANUAL FCC ID: M8C-TP36RF433-152 4. 4 OPERATIING INSTRUCTIONS ON ECE 1 2 3 4 5 ON ECE 1 2 3 4 5 The remote unit has 32 different code combinations, each transmitter of this remote control carries a unique ID code to facilitate communication between paired devices. The ID code is set by factory and is not user changeable. However, you will be required to perform an “ID code learning” process manually under these circumstances. • If you have multiple fans installed within a close proximity and want to control all fans NOT using the same remote transmitter. NOTE: Each fan requires its own receiver. • When your remote control is not responding (make sure battery is not flat). • After you have replaced a faulty transmitter or receiver with a new one. Otherwise the remote control will not work. To perform this process manually, follow steps below: Simply change the combination code by sliding dip switches in the remote. Press the “ OFF” button within 1 minute after restoring power to the fan, the fan will beep five times . This indicate the code learning process has been completed. 5. 5 Remote functions: OFF: Turns off the fan HI: High speed MED: Medium speed LO: Low speed, Press the button for 5 seconds to turn ON/OFF the buzzer Special function! Start the fan without transmitter in the following way: Flip the power switch 3 times within 8 seconds to obtain High speed Flip the power switch 4 times within 8 seconds to obtain Medium speed Flip the power switch 5 times within 8 seconds to obtain Low speed OFF HI MED LO 2 LIMITED LIFETIME W ARRANTY The manufacturer warrants this fan to be free from defects in work FCC WARNING manship and material present at time of shipment from the factory for life (with limitations) from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at no charge or , at our option, replace the ceiling fan with a comparable or superior model. To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the ceiling fan by accident, misuse or improper installation, or by affixing accessories not produced by this warranty, are at the purchaser’s own responsibility. The manufacturer assumes no responsibility whatsoever for fan installation during the limited lifetime warranty. Any service performed by an unauthorized person will render the warranty invalid. Due to varying climatic conditions, this warranty does not cover changes in brass finish, rusting, pitting, tarnishing, corroding or peeling. Brass finish fans maintain their beauty when protected from varying weather conditions. Any replacement of defective parts for the ceiling fan must be reported within the first year from the date of purchase. For the balance of the warranty, call our customer service department at 888 - 251 - 1003 for return authorization and shipping instructions so that we may repair or replace the ceiling fan. Any fan or parts returned improperly packaged is the sole responsibility of the purchaser. There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The duration of any implied warranty which cannot be disclaimed is limited to the lifetime limited period as specified in our warranty. The manufacturer shall not be liable for incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be accorded by law. This warranty gives you specific legal rights, and you also have other rights which vary from state to state. This warranty supersedes all prior warranties. Note: A small amount of “wobble” is normal and should not be considered a defect. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: The remote control has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The remote control generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and the receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or mod…

Text truncated - open the document above for the full version.

Agent letter FCC attestation statement Kiwa Page 1 of 2 RF_753, Issue 2 15-02-2023 [PLACE ON APPLICANT/COMPANY LETTERHEAD] U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: Kiwa Nederland B.V. Wilmersdorf 50 7327 AC Apeldoorn Postbus 137 7300 AC Apeldoorn Netherlands ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Name: Ivy Hsu FRN: 0033415266 Street address: 8 Ravendale, Irvine CA. 92602 ZIP/City/State 92602 Telephone number: (949)923-1870 Email address: [email protected] Signature: Date: 2024.3.22 This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission- related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Fego Precision Industrial Co., Ltd Grantee Code: M8C-TP36RF433-152 Contact person name: Bruce Chang Street address: No.947 Linsen Rd.,Wufong Dist. ZIP/City/State 41352,Taichung ,Taiwan Telephone number: +886(4)23391802 Email address: [email protected] Signature: Date: 03/19/2024

External photo of EUT

Internal photo of EUT Internal photo of EUT Internal photo of EUT

Copyright © 2024 Intertek STATEMENT ON EXPOSURE TO ELECTROMAGNETIC FIELDS Report No.: 240300314THC-001 Equipment Information Type of equipment ： Remote control transmitter Type / Model ： TP36RF433-152 FCC ID: ： M8C-TP36RF433-152 Applicant ： Fego Precision Industrial Co., Ltd. No 947 Lin-Sen Rd. Wu Fong Shiang, Taichung Hsien, Taiwan By request of ： 47 CFR FCC 1.1310 KDB 447498 JUSTIFICATION 2.1.2 1-mW Test Exemption Per § 1.1307(b)(3)(i)(A), a single RF source is exempt RF device (from the requirement to show data demonstrating compliance to RF exposure limits, as previously mentioned) if the available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption applies to all operating configurations and exposure conditions, for the frequency range 100 kHz to 100 GHz, regardless of fixed, mobile, or portable device exposure conditions. This is a standalone exemption, and it cannot be applied in conjunction with any other test exemption. The maximum RF output power was -7.48 dBm(0.18mW).The product has an average emitted power less than 1mW. The emitted peak power is also less than 1mW. Since the above conducted output power is well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing. Date of issue: Apr. 02, 2024 Zero Chen Engineer Intertek Testing Services Taiwan Ltd., Hsinchu Laboratory No. 17, Ln. 246, Niupu S. Rd., Xiangshan Dist, Hsinchu City 300075, Taiwan

Fego Precision Industrial Co., Ltd. TEST REPORT Model: TP36RF433-152 REPORT NUMBER 240200072THC-001 ISSUE DATE Mar. 19, 2024 PAGES 18 DOCUMENT CONTROL NUMBER GFT-OP-10h (28-Nov-2018) © 2020 Intertek Report No.: 240200072THC-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. GFT-OP-10h (28-Nov-2018) Page 1 of 18 Test Report 0597 Radio Spectrum TEST REPORT Applicant: Fego Precision Industrial Co., Ltd. No 947 Lin-Sen Rd. Wu Fong Shiang, Taichung Hsien, Taiwan Product: Remote control transmitter Model No.: TP36RF433-152 FCC ID: M8C-TP36RF433-152 Test Method/ Standard: 47 CFR FCC Part 15.231 Test By: Intertek Testing Services Taiwan Ltd., Hsinchu Laboratory No. 17, Ln. 246, Niupu S. Rd., Xiangshan Dist, Hsinchu City 300075, Taiwan Rich Nien Engineer Zero Chen Reviewer Report No.: 240200072THC-001 GFT-OP-10h (28-Nov-2018) Page 2 of 18 TEST REPORT Revision History Report No. Issue Date Revision Summary 240200072THC-001 Mar. 19, 2024 Original report Report No.: 240200072THC-001 GFT-OP-10h (28-Nov-2018) Page 3 of 18 TEST REPORT Table of Contents Summary of Test Data ................................................................................................................ 4 1. General Information ............................................................................................................... 5 1.1 Identification of the EUT .................................................................................................. 5 1.2 Antenna description ......................................................................................................... 5 1.3 Operation mode ............................................................................................................... 6 1.4 Peripherals equipment ..................................................................................................... 6 2. Radiated emission test FCC 15.231 (b) ................................................................................... 7 2.1.1 Radiated emission from 9kHz to 30MHz uses Loop Antenna: ...................................... 7 2.1.2 Radiated emission below 1GHz using Bilog Antenna .................................................... 8 2.1.3 Radiated emission above 1GHz using Horn Antenna .................................................... 8 3. Measured bandwidth FCC 15.231(C) ................................................................................... 14 4. Timing requirement of operated transmitter....................................................................... 15 5. Conducted emission FCC 15.207 .......................................................................................... 16 Appendix A: Test equipment list ............................................................................................... 17 Appendix B: Measurement Uncertainty ................................................................................... 18 Report No.: 240200072THC-001 GFT-OP-10h (28-Nov-2018) Page 4 of 18 TEST REPORT Summary of Test Data Test Requirement Applicable Rule Result Radiated Emission test 15.231(b), 15.209 Pass Measured bandwidth 15.231(c) Pass Timing requirement of operated transmitter 15.231(b) Pass Conducted Emission test 15.207 N/A Antenna Requirement 15.203 Pass Note: Please note that the test results with statement of conformity, the decision rules which are based on: Safety Testing: the specification, standard or IEC Guide 115. Other Testing: the specification, standard and not taking into account the measurement uncertainty. Report No.: 240200072THC-001 GFT-OP-10h (28-Nov-2018) Page 5 of 18 TEST REPORT 1. General Information 1.1 Identification of the EUT Product: Remote control transmitter Model No.: TP36RF433-152 Operating Frequency: 433.92MHz Rated Power: DC 3V Power Cord: N/A Sample receiving date: 2024/02/16 Sample condition: Workable Test Date(s): 2024/03/05 ~ 2024/03/07 1.2 Antenna description Antenna Type : Printed Antenna Connector Type : Fixed Report No.: 240200072THC-001 GFT-OP-10h (28-Nov-2018) Page 6 of 18 TEST REPORT 1.3 Operation mode The EUT was supplied with DC 3V from battery. The EUT is set in engineer mode to transmit continuously. The signal is maximized through rotation and placement in the three orthogonal axes. X axis Y axis Z axis After verifying three axes, we found the maximum electromagnetic field was occurred at Y axis. The final test data was executed under this configuration. Frequency (MHz) Signal on time (ms) Signal on & off time (ms) Duty Cycle Duty Cycle factor 433.92 38.55 100.00 0.386 8.28 1.4 Peripherals equipment Peripherals Brand Model No. Serial No. Data cable Battery * 2 GP R03 N/A N/A Report No.: 240200072THC-001 GFT-OP-10h (28-Nov-2018) Page 7 of 18 TEST REPORT 2. Radiated emission test FCC 15.231 (b) 2.1 Test setup & procedure 2.1.1 Radiated emission from 9kHz to 30MHz uses Loop Antenna: EUT & Peripherals 0.8m EMI Test Receiver □ 3 meters Loop Antenna 1m Report No.: 240200072THC-001 GFT-OP-10h (28-Nov-2018) Page 8 of 18 TEST REPORT 2.1.2 Radiated emission below 1GHz using Bilog Antenna 2.1.3 Radiated emission above 1GHz using Horn Antenna EMI Test…

Text truncated - open the document above for the full version.

Radiated Emission Test set-up photo 9kHz~30MHz Radiated Emission Test set-up photo 30MHz~1GHz Radiated Emission Test set-up photo Above 1GHz