MHIFYX-1WLAN 802.11bgn 2.4GHz 1x1 and BLE v4.0 Bridge

Card Access Products is a trademark of Card Access, Inc. registered in the United States. Qualcomm is a trademark of QUALCOMM, Incorporated, registered in the United States and other countries. FYX is a trademark of Qualcomm Labs, Inc., a wholly owned subsidiary of QUALCOMM, Incorporated. All QUALCOMM, Incorpo- rated and Qualcomm Labs, Inc. trademarks are used with permission. Bluetooth is a registered trademark of the Bluetooth SIG. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Other marks may be the property of their respective owners. Quick Start Guide For additional information, visit www.getfyx.com. FYX ™ HUB Proximity-based receiver and transmitter What is the FYX Hub? The FYX™ Hub is a proximity-based receiver and transmitter. It is an always-on device and plugs into a standard electrical outlet. It discovers, receives and transmits proximity and other data of interest from FYX Beacons and other devices running FYX-enabled applications via Bluetooth® Low Energy (BLE) short-range radio transmissions. Then, using Wi-Fi® transmissions, the Hub communicates this proximity and other data of interest to the GetFyx.com web service. The BLE and Wi-Fi radio signals transmitted from Beacons and transmit- ted and received by the Hub employ industry standard security tech- niques designed to prevent intruders from listening in on these mes- sages. The Hub is a password-protected device with a web-based Control Panel user interface (UI) for Hub setup and management. Before perform- ing the Hub setup, please visit http://www.getfyx.com/ to get started. Creating Rich Consumer Advertising and Marketing Experiences With the FYX Hub placed in indoor or outdoor business environments, proximity-based triggers provide dynamic customer experiences to en- gage, entice and interact with your business on a one-to-one level. With the FYX Hub, proximity detection creates a new level of interaction between mobile, web and in-store campaigns. Important Safety Instructions Read all instructions in this guide before using the FYX Hub. When using this product, the safety precautions below must be taken to avoid possi- ble legal liabilities and damages. Retain and follow all product safety and operating instructions. Observe all warnings in the operating instructions on the product. To reduce the risk of bodily injury, electric shock, fire and damage to the equipment, observe the following precautions: • The FYX Hub is for indoor use only and should be kept away from water or chemical contact. • The FYX Hub is an Information Technology device and is intended for use in households only. Do not install the device in locations that may expose the product to ignitable or flammable gases or liquids. • Do not expose the FYX Hub to extreme temperatures. • Plug the FYX Hub only into a power source in accordance with the input voltage ratings marked on the device. • Do no operate the FYX Hub with a damaged plug, or after the prod- uct malfunctions or is dropped or damaged in any manner. Avoid dropping the device. • To obtain a replacement product or service for examination, repair, electrical or mechanical adjustment, see the Warranty section of this document. • The FYX Hub is provided with double insulation and has no service- able parts. In a double insulated appliance, two levels of insulation are provided instead of grounding as a means of protecting the user from risk of electric shock. Servicing of a double-insulated appli- ance requires extreme care and knowledge of the system and should only be done by qualified service personnel. Replacement parts for double-insulated appliances must be identical to those parts in the appliance. A double-insulated appliance is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”, or the symbol: PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. 1 2 Before You Begin Before you begin setting up the FYX Hub for use with the GetFyx.com web service, you will need the following information (for easy reference, please write them in the spaces provided below). FYX Hub Information 1. Your FYX Hub Activation Code (the 9 alpha-numeric characters on the FYX Hub’s rear label appearing below the word “GetFYX.com”). 2. The FYX Hub Wi-Fi MAC Address (specifically, the last 6 of the 12 alpha-numeric characters printed on the Hub’s rear label in the lower left area). FYX Hub Activation Code: FYX Hub Wi-Fi MAC Address: 3 Plugging in Your FYX Hub Before you begin your FYX Hub setup, plug it into a power outlet. To do this, you must first attach the plug head to the back side of the Hub by performing the following steps: 1. Place the proper plug head into the socket on the back side of the Hub by aligning the four plug head tabs in the socket. 2. Push the plug head in and then up until the release button at the top of the socket clicks and locks the plug head into place. NOTE: To remove the plug head, press in the release button at the top of the socket and reverse the above steps. 3. Plug the Hub into the power outlet. NOTE: After plugging in the Hub, wait for AT LEAST ONE MINUTE to allow the Hub to initialize before connecting the Hub to your Wi-Fi Network. 5 Connecting Your FYX Hub to Your Wi-Fi Network Once you have visited http://www.getfyx.com/ to get started and followed the instructions there, you’re ready to connect the Hub to your Wi-Fi Network. This one-time setup is accomplished with the following steps: 1. If you have not plugged the Hub into an electrical outlet, please do so now (see Figure 1 in the previous section). 2. From your smartphone, tablet or computer, perform your device’s required steps to connect to a wireless network. 3. Connect to the Wi-Fi Network named FYX Hub (xxxxxx). NOTE: the “(xxxxxx)” alphanumeric characters in the Wi-Fi Network name are replaced with the last six characters of the Hub’s actual Wi-Fi MAC address. This address is printed on the Hub’s rear label. It is found on the Hub label’s lower left (See the Before You Begin section of th…

Text truncated - open the document above for the full version.

April 15, 2013 UL LLC Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL LLC to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL LLC on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL LLC as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; 2 g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, James A. Stout, Vice President of Engineering Card Access, Inc.

April 15, 2013 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: MHIFYX-1 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 10/15/2013 External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, James A. Stout, Vice President of Engineering Card Access, Inc.

Exhibit 9 FYX Hub External Photographs FCC Part 15 Certification FCC ID: MHIFYX-1 Model: CA-FYX100 STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Report Prepared by: QUALCOMM Labs Inc. 5775 Morehouse Drive San Diego, CA 92121-1714

Exhibit 8 FYX Hub FCC Label & Location FCC Part 15 Certification FCC ID: MHIFYX-1 Model: CA-FYX100 STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Report Prepared by: QUALCOMM Labs Inc. 5775 Morehouse Drive San Diego, CA 92121-1714

Exhibit 10 FYX Beacon Internal Photographs FCC Part 15 Certification FCC ID: MHIFYX-1 Model: CA-FYX100 STATEMENT OF CERTIFICATION The data, data evaluation and equipment configuration represented herein are a true and accurate representation of the measurements of the sample’s radio frequency interference emissions characteristics as of the dates and at the times of the test under the conditions herein specified. Report Prepared by: QUALCOMM Labs Inc. 5775 Morehouse Drive San Diego, CA 92121-1714

Qualcomm Labs, Inc. 5775 Morehouse Drive www.qualcommlabs.com San Diego, CA 92121-1714 (858) 587-1121 Page 1 of 1 Confidential and Proprietary – Qualcomm Labs, Inc. 04/09/2013 To: UL Japan, Inc. 4383-326 Asama-cho, Ise, Mie 516-0021 Japan Re: FYX Hub Japan Antenna Document Attn: To Whom it may concern The antennas in the FYX Hub device have the following characteristics: Type: PIFA Total Gain: 2.1dBi Return Loss: -15 dB ___________________________________________ Robert Scodellaro Senior Staff Engineer Qualcomm Labs, Inc.

FCC Part 1 Subpart I FCC Part 2 Subpart J INDUSTRY CANADA RSS 102 ISSUE 3 RF EXPOSURE REPORT FOR WLAN 802.11bgn 2.4GHz 1x1 and Bluetooth LE v4.0 Bridge MODEL NUMBER: CA-FYX100 FCC ID: MHIFYX-1 IC: 3681C FYX-1 REPORT NUMBER: 12U14684-18 ISSUE DATE: APRIL 26, 2013 Prepared for CARD ACCESS, INC 11778 SOUTH ELECTION ROAD SUITE 260 DRAPER, UT 84020, U.S.A. Prepared by UL CCS 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 12U14684-18 DATE: APRIL 26, 2012 FCC ID: MHIFYX-1 IC: 3681C FYX-1 Page 2 of 11 UL CCS FORM NO: CCSUP4701H 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Revision History Rev. Issue Date Revisions Revised By -- 04/26/13 Initial Issue F. Ibrahim REPORT NO: 12U14684-18 DATE: APRIL 26, 2012 FCC ID: MHIFYX-1 IC: 3681C FYX-1 Page 3 of 11 UL CCS FORM NO: CCSUP4701H 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. REFERENCES ................................................................................................................... 5 4. FACILITIES AND ACCREDITATION ................................................................................. 5 5. MAXIMUM PERMISSIBLE RF EXPOSURE ....................................................................... 6 5.1. FCC RULES ................................................................................................................ 6 5.2. IC RULES .................................................................................................................... 7 5.3. EQUATIONS ................................................................................................................ 8 5.4. LIMITS AND IC EXEMPTION .....................................................................................10 6. RF EXPOSURE RESULTS ................................................................................................11 REPORT NO: 12U14684-18 DATE: APRIL 26, 2012 FCC ID: MHIFYX-1 IC: 3681C FYX-1 Page 4 of 11 UL CCS FORM NO: CCSUP4701H 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: CARD ACCESS, INC 11778 SOUTH ELECTION ROAD SUITE 260 DRAPER, UT 84020, U.S.A. EUT DESCRIPTION: WLAN 802.11bgn 2.4GHz 1x1 and Bluetooth LE v4.0 Bridge MODEL: CA-FYX100 SERIAL NUMBER: CONDUCTED (CB1), RADIATED (RF1) DATE TESTED: JANUARY 30 - FEBRUARY 23, 2013 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 1 SUBPART I & PART 2 SUBPART J Pass INDUSTRY CANADA RSS 102 ISSUE 3 Pass UL CCS calculated the RF Exposure of the above equipment in accordance with the requirements set forth in the above standards, using test results reported in the test report documents referenced below and/or documentation furnished by the applicant. All indications of Pass/Fail in this report are opinions expressed by UL CCS based on interpretations of these calculations. The results show that the equipment is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL CCS and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL CCS will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For UL CCS By: Calculated By: FRANK IBRAHIM STEVE AGUILAR WiSE PROGRAM MANAGER EMC ENGINEER UL CCS UL CCS REPORT NO: 12U14684-18 DATE: APRIL 26, 2012 FCC ID: MHIFYX-1 IC: 3681C FYX-1 Page 5 of 11 UL CCS FORM NO: CCSUP4701H 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 2. TEST METHODOLOGY All calculations were made in accordance with FCC OET Bulletin 65 Edition 97-01 and IC Safety Code 6. 3. REFERENCES All measurements were made as documented in test report BNUL CCS Document 12U14684-2 (WLAN) and 12U14684-1 (BLE) for operation in the 2.4 GHz band. Output power, Duty cycle and Antenna gain data is excerpted from the applicable test reports. Antenna gain data is excerpted from the applicable test reports. 4. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 47173 Benicia Street, Fremont, California, USA. UL CCS is accredited by NVLAP, Laboratory Code 200065-0. The full scope of accreditation can be viewed at http://www.ccsemc.com. REPORT NO: 12U14684-18 DATE: APRIL 26, 2012 FCC ID: MHIFYX-1 IC: 3681C FYX-1 Page 6 of 11 UL CCS FORM NO: CCSUP4701H 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 5. MAXIMUM PERMISSIBLE RF EXPOSURE 5.1. FCC RULES §1.1310 The criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in §1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of §2.1093 of this chapter. REPORT NO: 12U14684-18 DATE…

Text truncated - open the document above for the full version.

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 BLUETOOTH LOW ENERGY CERTIFICATION TEST REPORT FOR WLAN 802.11bgn 2.4GHz 1x1 and Bluetooth LE v4.0 Bridge MODEL NUMBER: CA-FYX100 FCC ID: MHIFYX-1 IC: 3681C-FYX1 REPORT NUMBER: 12U14684-16 ISSUE DATE: APRIL 26, 2013 Prepared for CARD ACCESS, INC 11778 SOUTH ELECTION ROAD SUITE 260 DRAPER, UT 84020, U.S.A. Prepared by UL CCS 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 12U14684-16 DATE: APRIL 26, 2013 FCC ID: MHIFYX-1 IC: 3681C-FYX1 Page 2 of 50 UL CCS FORM NO: CCSUP4701G 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Revision History Rev. Issue Date Revisions Revised By -- 04/26/13 Initial Issue F. Ibrahim REPORT NO: 12U14684-16 DATE: APRIL 26, 2013 FCC ID: MHIFYX-1 IC: 3681C-FYX1 Page 3 of 50 UL CCS FORM NO: CCSUP4701G 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. FACILITIES AND ACCREDITATION ................................................................................. 5 4. CALIBRATION AND UNCERTAINTY ................................................................................ 5 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 5 4.2. SAMPLE CALCULATION ............................................................................................ 5 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 5 5. EQUIPMENT UNDER TEST ............................................................................................... 6 5.1. DESCRIPTION OF EUT .............................................................................................. 6 5.2. MAXIMUM OUTPUT POWER...................................................................................... 6 5.3. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 6 5.4. SOFTWARE AND FIRMWARE .................................................................................... 6 5.5. WORST-CASE CONFIGURATION AND MODE .......................................................... 6 5.6. DESCRIPTION OF TEST SETUP ................................................................................ 7 6. TEST AND MEASUREMENT EQUIPMENT ......................................................................10 7. ANTENNA PORT TEST RESULTS ...................................................................................11 7.1. ON TIME, DUTY CYCLE ............................................................................................11 7.2. 6 dB BANDWIDTH ......................................................................................................12 7.3. 99% BANDWIDTH ......................................................................................................15 7.4. OUTPUT POWER.......................................................................................................18 7.5. AVERAGE POWER ....................................................................................................21 7.6. POWER SPECTRAL DENSITY ..................................................................................22 7.7. CONDUCTED SPURIOUS EMISSIONS .....................................................................25 8. RADIATED TEST RESULTS .............................................................................................29 8.1. LIMITS AND PROCEDURE ........................................................................................29 8.2. TRANSMITTER ABOVE 1 GHz ..................................................................................30 8.3. WORST-CASE BELOW 1 GHz ...................................................................................38 9. AC POWER LINE CONDUCTED EMISSIONS ..................................................................41 10. SETUP PHOTOS ...........................................................................................................45 REPORT NO: 12U14684-16 DATE: APRIL 26, 2013 FCC ID: MHIFYX-1 IC: 3681C-FYX1 Page 4 of 50 UL CCS FORM NO: CCSUP4701G 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: CARD ACCESS, INC 11778 SOUTH ELECTION ROAD SUITE 260 DRAPER, UT 84020, U.S.A. EUT DESCRIPTION: WLAN 802.11bgn 2.4GHz 1x1 and Bluetooth LE v4.0 Bridge MODEL: CA-FYX100 SERIAL NUMBER: CONDUCTED (CB1), RADIATED (RF1) DATE TESTED: February 4 th -7 th , 2013 APPLICABLE STANDARDS STANDARD TEST RESULTS CFR 47 Part 15 Subpart C Pass INDUSTRY CANADA RSS-210 Issue 8 Annex 8 Pass INDUSTRY CANADA RSS-GEN Issue 3 Pass UL CCS tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL CCS based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL CCS and all revisions are duly note…

Text truncated - open the document above for the full version.

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 CERTIFICATION TEST REPORT FOR WLAN 802.11bgn 2.4GHz 1x1 and Bluetooth LE v4.0 Bridge MODEL NUMBER: CA-FYX100 FCC ID: MHIFYX-1 IC: 3681C-FYX1 REPORT NUMBER: 12U14684-17A ISSUE DATE: APRIL 26, 2013 Prepared for CARD ACCESS, INC 11778 SOUTH ELECTION ROAD SUITE 260 DRAPER, UT 84020, U.S.A. Prepared by UL CCS 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 12U14684-17A DATE: APRIL 26, 2013 FCC ID: MHIFYX-1 IC: 3681C-FYX1 Page 2 of 128 UL CCS FORM NO: CCSUP4701H 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Revision History Rev. Issue Date Revisions Revised By -- 04/26/13 Initial Issue F. Ibrahim REPORT NO: 12U14684-17A DATE: APRIL 26, 2013 FCC ID: MHIFYX-1 IC: 3681C-FYX1 Page 3 of 128 UL CCS FORM NO: CCSUP4701H 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 5 2. TEST METHODOLOGY ..................................................................................................... 6 3. FACILITIES AND ACCREDITATION ................................................................................. 6 4. CALIBRATION AND UNCERTAINTY ................................................................................ 6 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 6 4.2. SAMPLE CALCULATION ............................................................................................ 6 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 6 5. EQUIPMENT UNDER TEST ............................................................................................... 7 5.1. DESCRIPTION OF EUT .............................................................................................. 7 5.2. MAXIMUM OUTPUT POWER...................................................................................... 7 5.3. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 7 5.4. SOFTWARE AND FIRMWARE .................................................................................... 7 5.5. WORST-CASE CONFIGURATION AND MODE .......................................................... 8 5.6. DESCRIPTION OF TEST SETUP ................................................................................ 9 6. TEST AND MEASUREMENT EQUIPMENT ......................................................................12 7. ON TIME, DUTY CYCLE AND MEASUREMENT METHODS ...........................................13 7.1. ON TIME AND DUTY CYCLE RESULTS done ...........................................................13 7.2. MEASUREMENT METHODS .....................................................................................13 7.3. DUTY CYCLE PLOTS done ........................................................................................14 8. ANTENNA PORT TEST RESULTS ...................................................................................16 8.1. 802.11b MODE IN THE 2.4 GHz BAND ......................................................................16 8.1.1. 6 dB BANDWIDTH ...............................................................................................16 8.1.2. 99% BANDWIDTH ...............................................................................................19 8.1.3. AVERAGE POWER .............................................................................................22 8.1.4. OUTPUT POWER ...............................................................................................23 8.1.5. POWER SPECTRAL DENSITY ...........................................................................26 8.1.6. OUT-OF-BAND EMISSIONS ...............................................................................29 8.2. 802.11g MODE IN THE 2.4 GHz BAND ......................................................................34 8.2.1. 6 dB BANDWIDTH ...............................................................................................34 8.2.2. 99% BANDWIDTH ...............................................................................................37 8.2.3. AVERAGE POWER .............................................................................................40 8.2.4. OUTPUT POWER ...............................................................................................41 8.2.5. POWER SPECTRAL DENSITY ...........................................................................44 8.2.6. OUT-OF-BAND EMISSIONS ...............................................................................47 8.3. 802.11n HT20 MODE IN THE 2.4 GHz BAND ............................................................51 8.3.1. 6 dB BANDWIDTH ...............................................................................................51 REPORT NO: 12U14684-17A DATE: APRIL 26, 2013 FCC ID: MHIFYX-1 IC: 3681C-FYX1 Page 4 of 128 UL CCS FORM NO: CCSUP4701H 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 8.3.2. 99% BANDWIDTH ...............................................................................................54 8.3.3. AVERAGE POWER ...........................…

Text truncated - open the document above for the full version.