MI7-EZPRO25RFEzPro P-25 Base Station radio/repeater

T T E E C C H H N N I I C C A A L L D D E E S S C C R R I I P P T T I I O O N N A A P P C C O O P P 2 2 5 5 E E Z Z P P R R O O 2 2 5 5 R R F F – – I I N N S S T T A A L L L L A A T T I I O O N N G G U U I I D D E E Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 2 of 21 Initial Release Revision: 00 INDEX 1. INTRODUCTION 3 2. UNPACKING AND CHECKING 5 3. PREVIOUS CONSIDERATIONS 5 4. INFORMATION ON SAFETY AND ELECTROMAGNETIC COMPATIBILITY 5 5. EQUIPMENT DESCRIPTION 6 5.1 FRONT VIEW 7 5.2 REAR VIEW 8 5.3 MODULES 9 5.4 CABLING AND CONNECTORS 13 6. INSTALLATION GUIDE 14 6.1 LOCATION 14 6.2 POWER SUPPLY CONNECTION 14 6.3 ANTENNA CONNECTION 15 6.4 SWITCHING ON THE EZPRO25 RF 15 7. CONFIGURATION 16 8. INCIDENTS 16 8.1 ALARMS 16 8.2 ALARMS WITHOUT STATUS LEDS 19 Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 3 of 21 Initial Release Revision: 00 Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 4 of 21 Initial Release Revision: 00 1. INTRODUCTION The EZPRO25 RF module (Base Station Repeater) are a modular design, high performance products used as APCO repeaters. The radio system is available in the 806-870Mhz frequency band. The proper functioning of any electronic device depends on its correct use. It is therefore recommended that the instructions in this manual be followed. Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 5 of 21 Initial Release Revision: 00 2. UNPACKING AND CHECKING The following elements are supplied in the box: EZPRO25 RF 2 cables SMB RF Installation manual The equipment is supplied with all the modules already assembled in the rack and with the RF cables connected. The modules in the basic configuration are: Control (RCPU P25), Transmitter (RTX P25), power module (RPA P25), Receiver (RRX P25) and the power supply module (RPS P25). IMPORTANT: if any of these elements is missing or damaged, contact your dealer and / or installer. 3. PREVIOUS CONSIDERATIONS This manual contains information on instructions for installation, maintenance and use. Read the following pages before using this equipment. It is inadvisable to switch on the equipment without having previously connected the antenna or, in case of the EZPRO25 RF, the 50Ω load to the TNC connector. Doing so may seriously damage the equipment and even cause irreparable damage to the transmitter circuits. It is important to use an antenna adjusted to the work frequency. 4. INFORMATION ON SAFETY AND ELECTROMAGNETIC COMPATIBILITY The equipment has been designed according to the following standards: ‰ ETSI ETS 300 392-2 - V2.5.2 (2005-11) ‰ ETSI ETS 300 394-1 - V2.4.0 (2005-10) ‰ ETSI EN 301 489-18 - V1.3.1 (2002-08) ‰ EN 60950-1 - 2001 ‰ EN 60950-1:2001/A11:2004 ‰ EN 60215-1989 ‰ EN 60215:1989/A1:1992 ‰ EN 60215:1989/A2:1994 Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 6 of 21 Initial Release Revision: 00 These standards ensure the essential requirements established in article 3 of directive 1999/5/CE. In any case, take the following points into consideration: ‰ Most electronic equipment is susceptible to electromagnetic interference if it is not duly protected. If the EZPRO25 RF is placed near unprotected electronic devices, they may malfunction. ‰ The EZPRO25 RF must not transmit without its antenna connected or, in case of the EZPRO25 RF, without the 50Ω load in the TNC connector. ‰ When installing the antenna, follow the guidelines for exposure of the human body to high and low frequency electromagnetic fields. Follow the supplier’s / manufacturer’s instructions. ‰ Burns may be suffered if the antenna connector output of the power module (RPA P25) is touched by bare skin when the EZPRO25 RF are transmitting with the antenna disconnected. ‰ Take care when handling the EZPRO25 RF. It has sharp edges, which may cut if handled incorrectly. ‰ Maintenance and repair of these repeaters must be carried out by qualified personnel only. ‰ Connect the EZPRO25 RF chassis to the earth intake in the cabinet where it is to be installed. ‰ Switch off the EZPRO25 RF before inserting/removing any of its modules. ! Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 7 of 21 Initial Release Revision: 00 5. EQUIPMENT DESCRIPTION 5.1 FRONT VIEW ♦ EZPRO25 RF 1.- RPS P25 (Repeater Power Supply) 2.- RPA P25 (Repeater Power Amplifier) 3.- RTX P25 (Repeater Transmitter) 4.- RRX P25 (Repeater Receiver) 5.- Option RRX2 P25/BSYNC P25 ( Repeater Receiver 2 / EZPRO25 RF Synchronism) 6.- RCPU P25 (Repeater Control Processing Unit) 7 1 2 3 4 5 6 Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 8 of 21 Initial Release Revision: 00 5.2 REAR VIEW ♦ EZPRO25 RF 24 23 22 21 20 19 1817 16 15 14 9 10 1112 13 8 25 Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 9 of 21 Initial Release Revision: 00 5.3 MODULES 1. RPS P25 (REPEATER POWER SUPPLY) LEDs to indicate module status. LED TYPE NORMAL STATUS FUNCTIÓN SUPPLY Green On There are 26.4V at the RPS P25 input 24V or 26.4V Green On There are 26.4V at the RPS P25 output 13.2V Green On There are 13.2V at the RPS P25 output Power on switch (Ref. 7): ON/OFF switch to connect to and disconnect from the EZPRO25 RF 2. RPA P25 (REPEATER POWER AMPLIFIER) LEDs to indicate module status. LED TYPE NORMAL STATUS FUNCTIÓN ON Green On Power supply correct TX POWER Green On Module transmitting 3. RTX P25 (REPEATER TRANSMITTER) LEDs to indicate module status. LED TYPE NORMAL STATUS FUNCTIÓN ON Green On Power supply correct REF. ERROR Red Off Failure in the 10 MHz reference INT. ERROR Red Off Internal failure BBSR ERROR Red Off Communication failure with the RCPU P25 module RPA ERROR Red Off RPA P25 failure RPW ERRORRed Off Reflected power failure Code: Installation Guide EZPRO25 RF.do INSTALLATION GUIDE Date: 12/18/2007 Page: 10 of 21 Initial Release Revision: 00 Code: Installati…

Text truncated - open the document above for the full version.

EZPRO25 RF BLOCK DIAGRAMS Initial Release Revision: A PRODUCT: EZPRO25 RF DOCUMENT NUMBER: B800014_FDS VERSION: Initial Release REVISION: A DATE: 12/18/2007 CLASSIFICATION: General information Internal document DOCUMENT MAINTENANCE THIS DOCUMENT HAS 7 PAGES Revision History DATE AUTHOR DESCRIPTION A 12/18/2007 Doron Ben-Yehezkel Initial Release DOCUMENT APPROVAL ACTIVITY NAME DATE SIGNATURE Prepared Doron Ben-Yehezkel 12/18/2007 Revised Project Manager Approved R&D Director Document Number: 516.80551 EZPRO25 RF BLOCK DIAGRAMS Date: 12/18/2007 Page: 2 of 7 Initial Release Revision: A Disclaimer Although every reasonable effort has been made to ensure the accuracy of the information contained herein and any other referred document, this should not be construed as a commitment on the part of IP MobileNet S.A. Unipersonal, and the liability of IP MobileNet S.A. Unipersonal for any errors and omissions shall be limited to the correction of such errors and omissions. IP MobileNet S.A. Unipersonal welcomes any comment as a way to improve any delivered documentation. The information contained herein has been prepared for the use of appropriately trained personnel, and it is intended for the purpose of the agreement under which the information is submitted. Any party using or relying upon this information assumes full responsibility for such use and in no event shall IP MobileNet S.A. Unipersonal be liable to anyone for especial, collateral, incidental, or consequential damages in connection with or arising out of the use of this information. The information or statements given in these documents regarding the suitability, capacity or performance of the mentioned hardware or software products cannot be considered binding but shall be defined in the agreement made between IP MobileNet S.A. Unipersonal and the customer. IP MobileNet S.A. Unipersonal reserves the right to revise these documents and to make changes to its content at any time, without prior notification. Copyrights No part of the information contained herein and the other referred documents may be copied, distributed or transmitted by any means to any other party without prior written permission of IP MobileNet S.A. Unipersonal. The distribution of this document may be also covered by NDA (non-disclosure agreement) between IP MobileNet S.A. Unipersonal and the receiver. Please also note that part of these contents even may be covered by patent rights. This document, the referred documents and the described product are considered protected by copyright according to the applicable laws. IP MobileNet and the IP MobileNet logo are registered trademarks of IP MobileNet S.A. Unipersonal. Copyright © IP MobileNet S.A. Unipersonal. All rights reserved. Document Number: 516.80551 EZPRO25 RF BLOCK DIAGRAMS Date: 12/18/2007 Page: 3 of 7 Initial Release Revision: A CONTENTS: 1. EZPRO25 RF....................................................ERROR! BOOKMARK NOT DEFINED. 1.1. INTRODUCTION .................................................................................................... 4 1.2. GENERAL BLOCK DIAGRAMS ........................................................................... 5 Document Number: 516.80551 EZPRO25 RF BLOCK DIAGRAMS Date: 12/18/2007 Page: 4 of 7 Initial Release Revision: A 1. EZPRO25 RF 1.1. INTRODUCTION The EZPRO 25 RF is the APCO carrier of the EZPRO 25 system, with a transmitter output power of 100W. Document Number: 516.80551 EZPRO25 RF BLOCK DIAGRAMS Date: 12/18/2007 Page: 5 of 7 Initial Release Revision: A 1.2. GENERAL BLOCK DIAGRAMS DSP RRX Serial Control DSP RRX Paralell Control Reference 10 Mhz Power Amplifier Harmonic Filter Coupler Rev Power Detector PA Temp Detector RPA DSP RTX Paralell Control RAM 32 K words A Synchronism NMEA + PPS DSP RRX TMS320VC5410 DSP RTX TMS320VC5410 MPC860 HPI Driver Ethernet Synthesis Fi Synthesi s DRAM 1M x32 bits Flash 512K x8 bits EEPROM BDM Connector Monitor Expand RX Paralell Expand TX Paralell J-TAG Expand DSP RX Expand DSP TX Synch Signals MAX23 10 BaseT Ethernet VT100 Referencia 10 MHz / 0.2 ppm Expand MPC Paralell LEDs Power Supplies 5V,3.3V,2.5V 24 Vcc RCPU Filter 12.8 Mhz RADIO CH2 RRX RADIO CH1 RRX Synthesis RF (400Mhz) Synthesis Fi (36.864 Mhz) MODEM CLC 5902 CAG ADC CAG ADC Microcontrol M30624 LVDS LVDS Logic Monitor Power Supplies 5V / 3.3V RRX2 9.216Mhz EEPRO MAX23 SEGGE BSR Serial Control Protocol Reference 12.8 Mhz 24 Vcc VT100 Filter 12.8 Mhz RADIO CH2 RRX RADIO CH1 RRX Synthesis RF (400Mhz) Synthesis Fi (36.864 Mhz) MODEM CLC 5902 CAG ADC CAG ADC Microcontrol M30624 LVDS LVDS Logic Monitor Power Supplies 5V / 3.3V RRX1 9.216Mhz EEPRO MAX23 SEGGE 80 Mhz RPS DC/DC 24/13.2V 3A 24Vcc T Filter 10 Mhz Synthesis RF (400Mhz) Synthesis Fi (9,216Mhz) CMX 980 EEPRO Microcontrol M30624 LVDS LVDS DSP RTX Serial Control Monitor Power Supplies 5V,3.3V,13.2V 24 Vcc CPLD I/Q Switch Cartesion Loop Modulator RTX BSR Serial Control Protocol MAX23 VT 100 SEGGE 13,2 Reset Hardware Sync 1/2 Sync 1/2 Sync 1/2 Switch 13,2 Switch 24 24 Vcc Document Number: 516.80551 EZPRO25 RF BLOCK DIAGRAMS Date: 12/18/2007 Page: 6 of 7 Initial Release Revision: A Filter 12.8 Mhz RADIO CH2 RRX RADIO CH1 RRX Synthesis RF (400Mhz) Synthesis Fi (36.864 Mhz) MODEM CLC 5902 CAG ADC CAG ADC Microcontrol M30624 LVDS LVDS Logic Monitor Power Supplies 5V / 3.3V RRX2 9.216Mhz EEPRO MAX23 SEGGE BSR Serial Control Protocol Reference 10 Mhz 27 Vcc VT100 Filter RADIO CH2 RRX RADIO CH1 RRX Synthesis RF Synthesis IF DIGITAL DEMOD IF CAG ADC CAG ADC Microcontrol 16 bits LVDS LVDS Logic MONIT Power Supplies 5V / 3.3V RRX1 EEPRO RS232 PRGM RRX Parallel Bus RRX CONTROL BLOCK DIAGRAM T Filter Synthesis RF Synthesis IF BBP EEPRO Microcontrol 16bits LVDS LVDS DSP RTX Serial Control MONITO Power Supplies 5V,3.3V,13.2V Cartesion Loop Modulator RTX RS232 SEGGE BSR Serial Control Protocol Reference 10 Mhz 27 Vcc VT100 CPLD I/Q SWITCH RTX CONTROL BLOCK DIAGRAM Document Number: 516.80551 EZPRO25 RF BLOCK DIAGRAMS Date: 12/18/2007 Pa…

Text truncated - open the document above for the full version.

RPA BSR Photos Initial Release Revision: A 1. RPA P25 1.1. FRONT PICTURE

RXX BSR Photos Initial Release Revision: A 1. RRX P25 1.1. FRONT PICTURE

RTX BSR Photos Initial Release Revision: A 1. RTX P25 1.1. FRONT PICTURE

TOP LEVEL AND BACKPLANE PHOTOS Date: 12/18/2007 Page: 2 of 4 Initial Release Revision: A 1.4. REAR PICTURE Top Level and Backplane BSR Photos Initial Release Revision: A 1.5. GENERAL PICTURES TOP LEVEL AND BACKPLANE PHOTOS Date: 12/18/2007 Page: 4 of 4 Initial Release Revision: A

BSYNC BSR Photos Initial Release Revision: A 1. BSYNC BSR P25 1.1. FRONT PICTURE BSYNC PHOTOS Date: 12/18/2007 Page: 2 of 2 Initial Release Revision: A 1.2. BSYNC PCB TOP LAYER PICTURE 1.3. BSYNC PCB BOTTOM LAYER PICTURE Crystal Oscillator Package

RPA BSR Photos Initial Release Revision: A CONTENTS: 1. RPA P25 ....................................................................................................................... 2 1.1 FRONT PICTURE 4 1.2 RPA PCB TOP PICTURE 5 1.3 RPA PCB BOTTOM PICTURE 6 1.4 INPUT PCB TOP PICTURE 7 1.5 INPUT PCB BOTTOM PICTURE 8 1.6 OUTPUT PCB TOP PICTURE 9 1.7 OUTPUT PCB BOTTOM PICTURE 10 1.8 RPA P25 GENERAL PICTURES 11 RPA PHOTOS Date: 12/18/2007 Page: 2 of 12 Initial Release Revision: A 1. RPA P25 1.1. FRONT PICTURE RPA PHOTOS Date: 12/18/2007 Page: 3 of 12 Initial Release Revision: A 1.2. RPA PCB TOP PICTURE RPA PHOTOS Date: 12/18/2007 Page: 4 of 12 Initial Release Revision: A 1.3 RPA PCB BOTTOM PICTURE RPA PHOTOS Date: 12/18/2007 Page: 5 of 12 Initial Release Revision: A 1.4 INPUT PCB TOP PICTURE RPA PHOTOS Date: 12/18/2007 Page: 6 of 12 Initial Release Revision: A 1.5 INPUT PCB BOTTOM PICTURE RPA PHOTOS Date: 12/18/2007 Page: 7 of 12 Initial Release Revision: A 1.6 OUTPUT PCB TOP PICTURE RPA PHOTOS Date: 12/18/2007 Page: 8 of 12 Initial Release Revision: A 1.7 OUTPUT PCB BOTTOM PICTURE RPA PHOTOS Date: 12/18/2007 Page: 9 of 12 Initial Release Revision: A RPA PHOTOS Date: 12/18/2007 Page: 10 of 12 Initial Release Revision: A 1.8 RPA GENERAL PICTURES RPA PHOTOS Date: 12/18/2007 Page: 11 of 12 Initial Release Revision: A RPA PHOTOS Date: 12/18/2007 Page: 12 of 12 Initial Release Revision: A

RPS BSR Photos Initial Release Revision: A 1. RPS P25 1.1. FRONT PICTURE RPS PHOTOS Date: 12/18/2007 Page: 2 of 2 Initial Release Revision: A 1.2. RPS PCB TOP LAYER PICTURE 1.3. RPS PCB BOTTOM LAYER PICTURE

RXX BSR Photos Initial Release Revision: A 1. RRX P25 1.1. FRONT PICTURE RXX PHOTOS Date: 12/18/2007 Page: 2 of 4 Initial Release Revision: A 1.2. RRX PCB TOP LAYER PICTURE RXX PHOTOS Date: 12/18/2007 Page: 3 of 4 Initial Release Revision: A 1.3. RRX PCB BOTTOM LAYER PICTURE 1.4. GENERAL PICTURES RXX PHOTOS Date: 12/18/2007 Page: 4 of 4 Initial Release Revision: A

RTX BSR Photos Initial Release Revision: A 1. RTX P25 1.1. FRONT PICTURE RTX PHOTOS Date: 12/18/2007 Page: 2 of 4 Initial Release Revision: A 1.2. RTX PCB TOP LAYER PICTURE RTX PHOTOS Date: 12/18/2007 Page: 3 of 4 Initial Release Revision: A 1.3. RTX PCB BOTTOM LAYER PICTURE RTX PHOTOS Date: 12/18/2007 Page: 4 of 4 Initial Release Revision: A 1.4. GENERAL PICTURES

Top Level and Backplane BSR Photos Initial Release Revision: A 1. BACKPLANE P25 1.1. BACKPLANE PCB TOP LAYER PICTURE 1.2. BACKPLANE PCB BOTTOM LAYER PICTURE 1.3. FRONT PICTURE

RCPU BSR Photos Initial Release Revision: A 1. RCPU P25 1.1. FRONT PICTURE RCPU PHOTOS Date: 12/18/2007 Page: 2 of 3 Initial Release Revision: A 1.2. RCPU PCB TOP LAYER PICTURE RCPU PHOTOS Date: 12/18/2007 Page: 3 of 3 Initial Release Revision: A 1.3. RCPU PCB BOTTOM LAYER PICTURE

Page 1 of 56 Report No.: FC08-015 IP MOBILENET TEST REPORT FOR THE BASE STATION RADIO, BSR P25 FCC PART 90, FCC PART 15 SUBPART B SECTIONS 15.107 CLASS A, 15.109 CLASS A & 15.111 AND RSS-119 TESTING DATE OF ISSUE: FEBRUARY 18, 2008 PREPARED FOR: IP MobileNet 16842 Von Karman Avenue Irvine, CA 92606 PREPARED BY: Mary Ellen Clayton CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 P.O. No.: 005459-00 Date of test:February 4-12, 2008 W.O. No.: 87564 Report No.: FC08-015 This report contains a total of 56 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. The results in this report apply only to the items tested, as identified herein. Page 2 of 56 Report No.: FC08-015 TABLE OF CONTENTS Administrative Information .............................................................................................3 Approvals .........................................................................................................................3 Summary of Results .........................................................................................................4 Conditions During Testing ...............................................................................................4 Equipment Under Test (EUT) Description ......................................................................5 Equipment Under Test .....................................................................................................5 Peripheral Devices ...........................................................................................................5 Temperature and Humidity During Testing .....................................................................6 FCC 2.1033(c)(3) User’s Manual ....................................................................................6 FCC 2.1033(c)(4) Type of Emissions ..............................................................................6 FCC 2.1033(c)(5) Frequency Range ................................................................................6 FCC 2.1033(c)(6) Operating Power .................................................................................6 FCC 2.1033(c)(8) DC Voltages .......................................................................................6 FCC 2.1033(c)(9) Tune-Up Procedure ............................................................................6 FCC 2.1033(c)(10) Schematics and Circuitry Description ..............................................6 FCC 2.1033(c)(11) Label and Placement ........................................................................6 FCC 2.1033(c)(12) Submittal Photos ..............................................................................6 FCC 2.1033(c)(13) Modulation Information ...................................................................6 FCC 15.107 – AC Conducted Emissions .........................................................................7 FCC 15.109 – Radiated Emissions ..................................................................................26 FCC 15.111 – AC Conducted Emissions .........................................................................33 FCC 2.1033(c)(14)/2.1046/90.205(j) - RF Power Output ...............................................37 FCC 2.1033(c)(14)/2.1049(i)/90.209(b)(5) - Bandwidth Limitations .............................38 FCC 2.1033(c)(14)/2.1049(i)/90.210(g) & (h) – Emissions Mask ..................................41 FCC 2.1033(c)(14)/2.1049(i) – 99% Bandwidth .............................................................45 FCC 2.1033(c)(14)/2.1051/90.210(g) - Spurious Emissions at Antenna Terminal .........48 FCC 2.1033(c)(14)/2.1053/90.210(g) - Field Strength of Spurious Radiation ................50 FCC 2.1033(c)(14)/2.1055/90.213(a) - Frequency Stability ...........................................55 Page 3 of 56 Report No.: FC08-015 ADMINISTRATIVE INFORMATION DATE OF TEST: February 4-12, 2008 DATE OF RECEIPT: February 4, 2008 REPRESENTATIVE: Behruz Rezvani MANUFACTURER: TELTRONIC S.A.U. Poligono Malpica, Calle F-Oeste 50057 Zaragoza, Spain TEST LOCATION: CKC Laboratories, Inc. 110 Olinda Place Brea, CA 92823 FREQUENCY RANGE TESTED: 9 kHz -9 GHz TEST METHOD: TIA/EIA 603, FCC Part 90, RSS-119 and RSS-GEN PURPOSE OF TEST: To perform the testing of the Base Station Radio, BSR P25 with the requirements for FCC Part 90, FCC Part 15 Subpart B Sections 15.107 Class A, 15.109 Class A & 15.111, and RSS-119 devices. APPROVALS QUALITY ASSURANCE: TEST PERSONNEL: Steve Behm, Director of Engineering Services Shamnderjit Hundal, Test Technologist Stuart Yamamoto, EMC Engineer Page 4 of 56 Report No.: FC08-015 SUMMARY OF RESULTS Test Specification/Method Results Mains Conducted Emissions FCC Part 15 Subpart B Section 15.107 Class A Pass Radiated Emissions FCC Part 15 Subpart B Section 15.109 Class A Pass Antenna Port Test for Receivers FCC Part 15 Subpart B Section 15.111 Pass RF Power Output FCC 2.1046/90.205(j) Pass Bandwidth Limitations FCC 2.1049/90.209(b)(5) Pass Emissions Mask FCC 2.1049/90.210 Pass Antenna Conducted Spurious Emissions FCC2.1051/90.210(g) Pass Field Strength Spurious Emissions FCC 2.1053/90.210(g) Pass Frequency Stability FCC 2.1055(a) & (d)/90.213(a) Pass 99% Bandwidth RSS-119 Pass CONDITIONS DURING TESTING No modifications to the EUT were necessary during testing. Page 5 of 56 Report No.: FC08-015 EQUIPMENT UNDER TEST (EUT) DESCRIPTION The customer declares the EUT tested by CKC Laboratories was representative of a production unit. EQUIPMENT UNDER TEST Base Station Radio Manuf: TELTRONIC S.A.U. Model: BSR P25 806-870 Serial: 820978 FCC ID: MI7-BSRP25 (pending) PERIPHERAL DEVICES The EUT was tested with the following peripheral device(s): Power Supply Manuf: Astron Model: VLS-35M Serial: 208010009 Laptop Computer Manuf: Dell Corporation Model: Inspiron 4100 Serial: 8J6H711 Page 6 of 56 Report No.: FC08-015 TEMPERATURE AND H…

Text truncated - open the document above for the full version.

Test Setup Photos